72 lines
2.0 KiB
Plaintext
72 lines
2.0 KiB
Plaintext
|
STMicroelectronics STM32H7 Reset and Clock Controller
|
||
|
|
=====================================================
|
||
|
|
|
||
|
|
The RCC IP is both a reset and a clock controller.
|
||
|
|
|
||
|
|
Please refer to clock-bindings.txt for common clock controller binding usage.
|
||
|
|
Please also refer to reset.txt for common reset controller binding usage.
|
||
|
|
|
||
|
|
Required properties:
|
||
|
|
- compatible: Should be:
|
||
|
|
"st,stm32h743-rcc"
|
||
|
|
|
||
|
|
- reg: should be register base and length as documented in the
|
||
|
|
datasheet
|
||
|
|
|
||
|
|
- #reset-cells: 1, see below
|
||
|
|
|
||
|
|
- #clock-cells : from common clock binding; shall be set to 1
|
||
|
|
|
||
|
|
- clocks: External oscillator clock phandle
|
||
|
|
- high speed external clock signal (HSE)
|
||
|
|
- low speed external clock signal (LSE)
|
||
|
|
- external I2S clock (I2S_CKIN)
|
||
|
|
|
||
|
|
Optional properties:
|
||
|
|
- st,syscfg: phandle for pwrcfg, mandatory to disable/enable backup domain
|
||
|
|
write protection (RTC clock).
|
||
|
|
|
||
|
|
Example:
|
||
|
|
|
||
|
|
rcc: reset-clock-controller@58024400 {
|
||
|
|
compatible = "st,stm32h743-rcc", "st,stm32-rcc";
|
||
|
|
reg = <0x58024400 0x400>;
|
||
|
|
#reset-cells = <1>;
|
||
|
|
#clock-cells = <1>;
|
||
|
|
clocks = <&clk_hse>, <&clk_lse>, <&clk_i2s_ckin>;
|
||
|
|
|
||
|
|
st,syscfg = <&pwrcfg>;
|
||
|
|
};
|
||
|
|
|
||
|
|
The peripheral clock consumer should specify the desired clock by
|
||
|
|
having the clock ID in its "clocks" phandle cell.
|
||
|
|
|
||
|
|
Example:
|
||
|
|
|
||
|
|
timer5: timer@40000c00 {
|
||
|
|
compatible = "st,stm32-timer";
|
||
|
|
reg = <0x40000c00 0x400>;
|
||
|
|
interrupts = <50>;
|
||
|
|
clocks = <&rcc TIM5_CK>;
|
||
|
|
};
|
||
|
|
|
||
|
|
Specifying softreset control of devices
|
||
|
|
=======================================
|
||
|
|
|
||
|
|
Device nodes should specify the reset channel required in their "resets"
|
||
|
|
property, containing a phandle to the reset device node and an index specifying
|
||
|
|
which channel to use.
|
||
|
|
The index is the bit number within the RCC registers bank, starting from RCC
|
||
|
|
base address.
|
||
|
|
It is calculated as: index = register_offset / 4 * 32 + bit_offset.
|
||
|
|
Where bit_offset is the bit offset within the register.
|
||
|
|
|
||
|
|
For example, for CRC reset:
|
||
|
|
crc = AHB4RSTR_offset / 4 * 32 + CRCRST_bit_offset = 0x88 / 4 * 32 + 19 = 1107
|
||
|
|
|
||
|
|
Example:
|
||
|
|
|
||
|
|
timer2 {
|
||
|
|
resets = <&rcc STM32H7_APB1L_RESET(TIM2)>;
|
||
|
|
};
|