2023-08-30 17:31:07 +02:00
|
|
|
# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
|
|
|
|
# Copyright (C) 2019 Renesas Electronics Corp.
|
|
|
|
%YAML 1.2
|
|
|
|
---
|
|
|
|
$id: http://devicetree.org/schemas/media/i2c/maxim,max9286.yaml#
|
|
|
|
$schema: http://devicetree.org/meta-schemas/core.yaml#
|
|
|
|
|
|
|
|
title: Maxim Integrated Quad GMSL Deserializer
|
|
|
|
|
|
|
|
maintainers:
|
|
|
|
- Jacopo Mondi <jacopo+renesas@jmondi.org>
|
|
|
|
- Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
|
|
|
|
- Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
|
|
|
|
- Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
|
|
|
|
|
|
|
|
description: |
|
|
|
|
The MAX9286 deserializer receives video data on up to 4 Gigabit Multimedia
|
|
|
|
Serial Links (GMSL) and outputs them on a CSI-2 D-PHY port using up to 4 data
|
|
|
|
lanes.
|
|
|
|
|
|
|
|
In addition to video data, the GMSL links carry a bidirectional control
|
|
|
|
channel that encapsulates I2C messages. The MAX9286 forwards all I2C traffic
|
|
|
|
not addressed to itself to the other side of the links, where a GMSL
|
|
|
|
serializer will output it on a local I2C bus. In the other direction all I2C
|
|
|
|
traffic received over GMSL by the MAX9286 is output on the local I2C bus.
|
|
|
|
|
|
|
|
properties:
|
|
|
|
'#address-cells':
|
|
|
|
const: 1
|
|
|
|
|
|
|
|
'#size-cells':
|
|
|
|
const: 0
|
|
|
|
|
|
|
|
compatible:
|
|
|
|
const: maxim,max9286
|
|
|
|
|
|
|
|
reg:
|
|
|
|
description: I2C device address
|
|
|
|
maxItems: 1
|
|
|
|
|
|
|
|
poc-supply:
|
|
|
|
description: Regulator providing Power over Coax to all the ports
|
|
|
|
|
|
|
|
enable-gpios:
|
|
|
|
description: GPIO connected to the \#PWDN pin with inverted polarity
|
|
|
|
maxItems: 1
|
|
|
|
|
|
|
|
gpio-controller: true
|
|
|
|
|
|
|
|
'#gpio-cells':
|
|
|
|
const: 2
|
|
|
|
|
|
|
|
maxim,bus-width:
|
|
|
|
$ref: /schemas/types.yaml#/definitions/uint32
|
|
|
|
enum: [ 24, 27, 32 ]
|
|
|
|
description: |
|
|
|
|
The GMSL serial data bus width. This setting is normally controlled by
|
|
|
|
the BWS pin, but may be overridden with this property. The value must
|
|
|
|
match the configuration of the remote serializers.
|
|
|
|
|
|
|
|
maxim,i2c-remote-bus-hz:
|
|
|
|
enum: [ 8470, 28300, 84700, 105000, 173000, 339000, 533000, 837000 ]
|
|
|
|
default: 105000
|
|
|
|
description: |
|
|
|
|
The I2C clock frequency for the remote I2C buses. The value must match
|
|
|
|
the configuration of the remote serializers.
|
|
|
|
|
|
|
|
maxim,reverse-channel-microvolt:
|
|
|
|
minimum: 30000
|
|
|
|
maximum: 200000
|
|
|
|
default: 170000
|
|
|
|
description: |
|
|
|
|
Initial amplitude of the reverse control channel, in micro volts.
|
|
|
|
|
|
|
|
The initial amplitude shall be adjusted to a value compatible with the
|
|
|
|
configuration of the connected remote serializer.
|
|
|
|
|
|
|
|
Some camera modules (for example RDACM20) include an on-board MCU that
|
|
|
|
pre-programs the embedded serializer with power supply noise immunity
|
|
|
|
(high-threshold) enabled. A typical value of the deserializer's reverse
|
|
|
|
channel amplitude to communicate with pre-programmed serializers is
|
|
|
|
170000 micro volts.
|
|
|
|
|
|
|
|
A typical value for the reverse channel amplitude to communicate with
|
|
|
|
a remote serializer whose high-threshold noise immunity is not enabled
|
|
|
|
is 100000 micro volts
|
|
|
|
|
|
|
|
maxim,gpio-poc:
|
2023-10-24 12:59:35 +02:00
|
|
|
$ref: /schemas/types.yaml#/definitions/uint32-array
|
2023-08-30 17:31:07 +02:00
|
|
|
minItems: 2
|
|
|
|
maxItems: 2
|
|
|
|
description: |
|
|
|
|
Index of the MAX9286 gpio output line (0 or 1) that controls Power over
|
|
|
|
Coax to the cameras and its associated polarity flag.
|
|
|
|
|
|
|
|
The property accepts an array of two unsigned integers, the first being
|
|
|
|
the gpio line index (0 or 1) and the second being the gpio line polarity
|
|
|
|
flag (GPIO_ACTIVE_HIGH or GPIO_ACTIVE_LOW) as defined in
|
|
|
|
<include/dt-bindings/gpio/gpio.h>.
|
|
|
|
|
|
|
|
When the remote cameras power is controlled by one of the MAX9286 gpio
|
|
|
|
lines, this property has to be used to specify which line among the two
|
|
|
|
available ones controls the remote camera power enablement.
|
|
|
|
|
|
|
|
When this property is used it is not possible to register a gpio
|
|
|
|
controller as the gpio lines are controlled directly by the MAX9286 and
|
|
|
|
not available for consumers, nor the 'poc-supply' property should be
|
|
|
|
specified.
|
|
|
|
|
|
|
|
ports:
|
|
|
|
$ref: /schemas/graph.yaml#/properties/ports
|
|
|
|
|
|
|
|
properties:
|
|
|
|
port@0:
|
|
|
|
$ref: /schemas/graph.yaml#/properties/port
|
|
|
|
description: GMSL Input 0
|
|
|
|
|
|
|
|
port@1:
|
|
|
|
$ref: /schemas/graph.yaml#/properties/port
|
|
|
|
description: GMSL Input 1
|
|
|
|
|
|
|
|
port@2:
|
|
|
|
$ref: /schemas/graph.yaml#/properties/port
|
|
|
|
description: GMSL Input 2
|
|
|
|
|
|
|
|
port@3:
|
|
|
|
$ref: /schemas/graph.yaml#/properties/port
|
|
|
|
description: GMSL Input 3
|
|
|
|
|
|
|
|
port@4:
|
|
|
|
$ref: /schemas/graph.yaml#/$defs/port-base
|
|
|
|
unevaluatedProperties: false
|
|
|
|
description: CSI-2 Output
|
|
|
|
|
|
|
|
properties:
|
|
|
|
endpoint:
|
|
|
|
$ref: /schemas/media/video-interfaces.yaml#
|
|
|
|
unevaluatedProperties: false
|
|
|
|
|
|
|
|
properties:
|
|
|
|
data-lanes: true
|
|
|
|
|
|
|
|
required:
|
|
|
|
- data-lanes
|
|
|
|
|
|
|
|
required:
|
|
|
|
- port@4
|
|
|
|
|
|
|
|
i2c-mux:
|
|
|
|
type: object
|
|
|
|
$ref: /schemas/i2c/i2c-mux.yaml#
|
|
|
|
unevaluatedProperties: false
|
|
|
|
description: |
|
|
|
|
Each GMSL link is modelled as a child bus of an i2c bus multiplexer/switch.
|
|
|
|
|
|
|
|
patternProperties:
|
|
|
|
"^i2c@[0-3]$":
|
|
|
|
type: object
|
2023-10-24 12:59:35 +02:00
|
|
|
additionalProperties: false
|
2023-08-30 17:31:07 +02:00
|
|
|
description: |
|
|
|
|
Child node of the i2c bus multiplexer which represents a GMSL link.
|
|
|
|
Each serializer device on the GMSL link remote end is represented with
|
|
|
|
an i2c-mux child node. The MAX9286 chip supports up to 4 GMSL
|
|
|
|
channels.
|
|
|
|
|
|
|
|
properties:
|
|
|
|
reg:
|
|
|
|
description: The index of the GMSL channel.
|
|
|
|
maxItems: 1
|
|
|
|
|
2023-10-24 12:59:35 +02:00
|
|
|
'#address-cells':
|
|
|
|
const: 1
|
|
|
|
|
|
|
|
'#size-cells':
|
|
|
|
const: 0
|
|
|
|
|
2023-08-30 17:31:07 +02:00
|
|
|
patternProperties:
|
|
|
|
"^camera@[a-f0-9]+$":
|
|
|
|
type: object
|
|
|
|
description: |
|
|
|
|
The remote camera device, composed by a GMSL serializer and a
|
|
|
|
connected video source.
|
|
|
|
|
|
|
|
properties:
|
|
|
|
compatible:
|
|
|
|
description: The remote device compatible string.
|
|
|
|
|
|
|
|
reg:
|
|
|
|
minItems: 2
|
|
|
|
maxItems: 3
|
|
|
|
description: |
|
|
|
|
The I2C addresses to be assigned to the remote devices through
|
|
|
|
address reprogramming. The number of entries depends on the
|
|
|
|
requirements of the currently connected remote device.
|
|
|
|
|
|
|
|
port:
|
|
|
|
$ref: /schemas/graph.yaml#/properties/port
|
|
|
|
description: Connection to the MAX9286 sink.
|
|
|
|
|
|
|
|
required:
|
|
|
|
- compatible
|
|
|
|
- reg
|
|
|
|
- port
|
|
|
|
|
|
|
|
additionalProperties: false
|
|
|
|
|
|
|
|
patternProperties:
|
|
|
|
"^port[0-3]-poc-supply$":
|
|
|
|
description: Regulator providing Power over Coax for a particular port
|
|
|
|
|
|
|
|
required:
|
|
|
|
- compatible
|
|
|
|
- reg
|
|
|
|
- ports
|
|
|
|
- i2c-mux
|
|
|
|
|
|
|
|
allOf:
|
|
|
|
# Only one way of specifying power supplies is allowed: 'maxim,gpio-poc',
|
|
|
|
# 'poc-supply' or per-port poc-supply. Additionally, if 'maxim,gpio-poc' is
|
|
|
|
# present, then 'gpio-controller' isn't allowed.
|
|
|
|
- if:
|
|
|
|
required:
|
|
|
|
- maxim,gpio-poc
|
|
|
|
then:
|
|
|
|
properties:
|
|
|
|
poc-supply: false
|
|
|
|
gpio-controller: false
|
|
|
|
patternProperties:
|
|
|
|
"^port[0-3]-poc-supply$": false
|
|
|
|
|
|
|
|
- if:
|
|
|
|
required:
|
|
|
|
- poc-supply
|
|
|
|
then:
|
|
|
|
patternProperties:
|
|
|
|
"^port[0-3]-poc-supply$": false
|
|
|
|
|
|
|
|
additionalProperties: false
|
|
|
|
|
|
|
|
examples:
|
|
|
|
- |
|
|
|
|
#include <dt-bindings/gpio/gpio.h>
|
|
|
|
|
|
|
|
i2c@e66d8000 {
|
|
|
|
#address-cells = <1>;
|
|
|
|
#size-cells = <0>;
|
|
|
|
|
|
|
|
reg = <0 0xe66d8000>;
|
|
|
|
|
|
|
|
gmsl-deserializer@2c {
|
|
|
|
compatible = "maxim,max9286";
|
|
|
|
reg = <0x2c>;
|
|
|
|
poc-supply = <&camera_poc_12v>;
|
|
|
|
enable-gpios = <&gpio 13 GPIO_ACTIVE_HIGH>;
|
|
|
|
|
|
|
|
gpio-controller;
|
|
|
|
#gpio-cells = <2>;
|
|
|
|
|
|
|
|
maxim,i2c-remote-bus-hz = <339000>;
|
|
|
|
maxim,reverse-channel-microvolt = <170000>;
|
|
|
|
|
|
|
|
ports {
|
|
|
|
#address-cells = <1>;
|
|
|
|
#size-cells = <0>;
|
|
|
|
|
|
|
|
port@0 {
|
|
|
|
reg = <0>;
|
|
|
|
|
|
|
|
max9286_in0: endpoint {
|
|
|
|
remote-endpoint = <&rdacm20_out0>;
|
|
|
|
};
|
|
|
|
};
|
|
|
|
|
|
|
|
port@1 {
|
|
|
|
reg = <1>;
|
|
|
|
|
|
|
|
max9286_in1: endpoint {
|
|
|
|
remote-endpoint = <&rdacm20_out1>;
|
|
|
|
};
|
|
|
|
};
|
|
|
|
|
|
|
|
port@2 {
|
|
|
|
reg = <2>;
|
|
|
|
|
|
|
|
max9286_in2: endpoint {
|
|
|
|
remote-endpoint = <&rdacm20_out2>;
|
|
|
|
};
|
|
|
|
};
|
|
|
|
|
|
|
|
port@3 {
|
|
|
|
reg = <3>;
|
|
|
|
|
|
|
|
max9286_in3: endpoint {
|
|
|
|
remote-endpoint = <&rdacm20_out3>;
|
|
|
|
};
|
|
|
|
};
|
|
|
|
|
|
|
|
port@4 {
|
|
|
|
reg = <4>;
|
|
|
|
|
|
|
|
max9286_out: endpoint {
|
|
|
|
data-lanes = <1 2 3 4>;
|
|
|
|
remote-endpoint = <&csi40_in>;
|
|
|
|
};
|
|
|
|
};
|
|
|
|
};
|
|
|
|
|
|
|
|
i2c-mux {
|
|
|
|
#address-cells = <1>;
|
|
|
|
#size-cells = <0>;
|
|
|
|
|
|
|
|
i2c@0 {
|
|
|
|
#address-cells = <1>;
|
|
|
|
#size-cells = <0>;
|
|
|
|
reg = <0>;
|
|
|
|
|
|
|
|
camera@51 {
|
|
|
|
compatible = "imi,rdacm20";
|
|
|
|
reg = <0x51>, <0x61>;
|
|
|
|
|
|
|
|
port {
|
|
|
|
rdacm20_out0: endpoint {
|
|
|
|
remote-endpoint = <&max9286_in0>;
|
|
|
|
};
|
|
|
|
};
|
|
|
|
|
|
|
|
};
|
|
|
|
};
|
|
|
|
|
|
|
|
i2c@1 {
|
|
|
|
#address-cells = <1>;
|
|
|
|
#size-cells = <0>;
|
|
|
|
reg = <1>;
|
|
|
|
|
|
|
|
camera@52 {
|
|
|
|
compatible = "imi,rdacm20";
|
|
|
|
reg = <0x52>, <0x62>;
|
|
|
|
|
|
|
|
port {
|
|
|
|
rdacm20_out1: endpoint {
|
|
|
|
remote-endpoint = <&max9286_in1>;
|
|
|
|
};
|
|
|
|
};
|
|
|
|
};
|
|
|
|
};
|
|
|
|
|
|
|
|
i2c@2 {
|
|
|
|
#address-cells = <1>;
|
|
|
|
#size-cells = <0>;
|
|
|
|
reg = <2>;
|
|
|
|
|
|
|
|
camera@53 {
|
|
|
|
compatible = "imi,rdacm20";
|
|
|
|
reg = <0x53>, <0x63>;
|
|
|
|
|
|
|
|
port {
|
|
|
|
rdacm20_out2: endpoint {
|
|
|
|
remote-endpoint = <&max9286_in2>;
|
|
|
|
};
|
|
|
|
};
|
|
|
|
};
|
|
|
|
};
|
|
|
|
|
|
|
|
i2c@3 {
|
|
|
|
#address-cells = <1>;
|
|
|
|
#size-cells = <0>;
|
|
|
|
reg = <3>;
|
|
|
|
|
|
|
|
camera@54 {
|
|
|
|
compatible = "imi,rdacm20";
|
|
|
|
reg = <0x54>, <0x64>;
|
|
|
|
|
|
|
|
port {
|
|
|
|
rdacm20_out3: endpoint {
|
|
|
|
remote-endpoint = <&max9286_in3>;
|
|
|
|
};
|
|
|
|
};
|
|
|
|
};
|
|
|
|
};
|
|
|
|
};
|
|
|
|
};
|
|
|
|
|
|
|
|
/*
|
|
|
|
* Example of a deserializer that controls the camera Power over Coax
|
|
|
|
* through one of its gpio lines.
|
|
|
|
*/
|
|
|
|
gmsl-deserializer@6c {
|
|
|
|
compatible = "maxim,max9286";
|
|
|
|
reg = <0x6c>;
|
|
|
|
enable-gpios = <&gpio 14 GPIO_ACTIVE_HIGH>;
|
|
|
|
|
|
|
|
/*
|
|
|
|
* The remote camera power is controlled by MAX9286 GPIO line #0.
|
|
|
|
* No 'poc-supply' nor 'gpio-controller' are specified.
|
|
|
|
*/
|
|
|
|
maxim,gpio-poc = <0 GPIO_ACTIVE_LOW>;
|
|
|
|
|
|
|
|
/*
|
|
|
|
* Do not describe connections as they're the same as in the previous
|
|
|
|
* example.
|
|
|
|
*/
|
|
|
|
ports {
|
|
|
|
#address-cells = <1>;
|
|
|
|
#size-cells = <0>;
|
|
|
|
|
|
|
|
port@4 {
|
|
|
|
reg = <4>;
|
|
|
|
};
|
|
|
|
};
|
|
|
|
|
|
|
|
i2c-mux {
|
|
|
|
#address-cells = <1>;
|
|
|
|
#size-cells = <0>;
|
|
|
|
};
|
|
|
|
};
|
|
|
|
};
|