71 lines
2.2 KiB
Plaintext
71 lines
2.2 KiB
Plaintext
|
Amlogic Meson AXG DWC PCIE SoC controller
|
||
|
|
|
||
|
|
Amlogic Meson PCIe host controller is based on the Synopsys DesignWare PCI core.
|
||
|
|
It shares common functions with the PCIe DesignWare core driver and
|
||
|
|
inherits common properties defined in
|
||
|
|
Documentation/devicetree/bindings/pci/snps,dw-pcie.yaml.
|
||
|
|
|
||
|
|
Additional properties are described here:
|
||
|
|
|
||
|
|
Required properties:
|
||
|
|
- compatible:
|
||
|
|
should contain :
|
||
|
|
- "amlogic,axg-pcie" for AXG SoC Family
|
||
|
|
- "amlogic,g12a-pcie" for G12A SoC Family
|
||
|
|
to identify the core.
|
||
|
|
- reg:
|
||
|
|
should contain the configuration address space.
|
||
|
|
- reg-names: Must be
|
||
|
|
- "elbi" External local bus interface registers
|
||
|
|
- "cfg" Meson specific registers
|
||
|
|
- "config" PCIe configuration space
|
||
|
|
- reset-gpios: The GPIO to generate PCIe PERST# assert and deassert signal.
|
||
|
|
- clocks: Must contain an entry for each entry in clock-names.
|
||
|
|
- clock-names: Must include the following entries:
|
||
|
|
- "pclk" PCIe GEN 100M PLL clock
|
||
|
|
- "port" PCIe_x(A or B) RC clock gate
|
||
|
|
- "general" PCIe Phy clock
|
||
|
|
- resets: phandle to the reset lines.
|
||
|
|
- reset-names: must contain "port" and "apb"
|
||
|
|
- "port" Port A or B reset
|
||
|
|
- "apb" Share APB reset
|
||
|
|
- phys: should contain a phandle to the PCIE phy
|
||
|
|
- phy-names: must contain "pcie"
|
||
|
|
|
||
|
|
- device_type:
|
||
|
|
should be "pci". As specified in snps,dw-pcie.yaml
|
||
|
|
|
||
|
|
|
||
|
|
Example configuration:
|
||
|
|
|
||
|
|
pcie: pcie@f9800000 {
|
||
|
|
compatible = "amlogic,axg-pcie", "snps,dw-pcie";
|
||
|
|
reg = <0x0 0xf9800000 0x0 0x400000
|
||
|
|
0x0 0xff646000 0x0 0x2000
|
||
|
|
0x0 0xf9f00000 0x0 0x100000>;
|
||
|
|
reg-names = "elbi", "cfg", "config";
|
||
|
|
reset-gpios = <&gpio GPIOX_19 GPIO_ACTIVE_HIGH>;
|
||
|
|
interrupts = <GIC_SPI 177 IRQ_TYPE_EDGE_RISING>;
|
||
|
|
#interrupt-cells = <1>;
|
||
|
|
interrupt-map-mask = <0 0 0 0>;
|
||
|
|
interrupt-map = <0 0 0 0 &gic GIC_SPI 179 IRQ_TYPE_EDGE_RISING>;
|
||
|
|
bus-range = <0x0 0xff>;
|
||
|
|
#address-cells = <3>;
|
||
|
|
#size-cells = <2>;
|
||
|
|
device_type = "pci";
|
||
|
|
ranges = <0x82000000 0 0 0x0 0xf9c00000 0 0x00300000>;
|
||
|
|
|
||
|
|
clocks = <&clkc CLKID_USB
|
||
|
|
&clkc CLKID_PCIE_A
|
||
|
|
&clkc CLKID_PCIE_CML_EN0>;
|
||
|
|
clock-names = "general",
|
||
|
|
"pclk",
|
||
|
|
"port";
|
||
|
|
resets = <&reset RESET_PCIE_A>,
|
||
|
|
<&reset RESET_PCIE_APB>;
|
||
|
|
reset-names = "port",
|
||
|
|
"apb";
|
||
|
|
phys = <&pcie_phy>;
|
||
|
|
phy-names = "pcie";
|
||
|
|
};
|