96 lines
2.7 KiB
C
96 lines
2.7 KiB
C
|
/* SPDX-License-Identifier: GPL-2.0 */
|
||
|
|
#ifndef _BMC150_ACCEL_H_
|
||
|
|
#define _BMC150_ACCEL_H_
|
||
|
|
|
||
|
|
#include <linux/atomic.h>
|
||
|
|
#include <linux/iio/iio.h>
|
||
|
|
#include <linux/mutex.h>
|
||
|
|
#include <linux/regulator/consumer.h>
|
||
|
|
#include <linux/workqueue.h>
|
||
|
|
|
||
|
|
struct regmap;
|
||
|
|
struct i2c_client;
|
||
|
|
struct bmc150_accel_chip_info;
|
||
|
|
struct bmc150_accel_interrupt_info;
|
||
|
|
|
||
|
|
/*
|
||
|
|
* We can often guess better than "UNKNOWN" based on the device IDs
|
||
|
|
* but unfortunately this information is not always accurate. There are some
|
||
|
|
* devices where ACPI firmware specifies an ID like "BMA250E" when the device
|
||
|
|
* actually has a BMA222E. The driver attempts to detect those by reading the
|
||
|
|
* chip ID from the registers but this information is not always enough either.
|
||
|
|
*
|
||
|
|
* Therefore, this enum should be only used when the chip ID detection is not
|
||
|
|
* enough and we can be reasonably sure that the device IDs are reliable
|
||
|
|
* in practice (e.g. for device tree platforms).
|
||
|
|
*/
|
||
|
|
enum bmc150_type {
|
||
|
|
BOSCH_UNKNOWN,
|
||
|
|
BOSCH_BMC156,
|
||
|
|
};
|
||
|
|
|
||
|
|
struct bmc150_accel_interrupt {
|
||
|
|
const struct bmc150_accel_interrupt_info *info;
|
||
|
|
atomic_t users;
|
||
|
|
};
|
||
|
|
|
||
|
|
struct bmc150_accel_trigger {
|
||
|
|
struct bmc150_accel_data *data;
|
||
|
|
struct iio_trigger *indio_trig;
|
||
|
|
int (*setup)(struct bmc150_accel_trigger *t, bool state);
|
||
|
|
int intr;
|
||
|
|
bool enabled;
|
||
|
|
};
|
||
|
|
|
||
|
|
enum bmc150_accel_interrupt_id {
|
||
|
|
BMC150_ACCEL_INT_DATA_READY,
|
||
|
|
BMC150_ACCEL_INT_ANY_MOTION,
|
||
|
|
BMC150_ACCEL_INT_WATERMARK,
|
||
|
|
BMC150_ACCEL_INTERRUPTS,
|
||
|
|
};
|
||
|
|
|
||
|
|
enum bmc150_accel_trigger_id {
|
||
|
|
BMC150_ACCEL_TRIGGER_DATA_READY,
|
||
|
|
BMC150_ACCEL_TRIGGER_ANY_MOTION,
|
||
|
|
BMC150_ACCEL_TRIGGERS,
|
||
|
|
};
|
||
|
|
|
||
|
|
struct bmc150_accel_data {
|
||
|
|
struct regmap *regmap;
|
||
|
|
struct regulator_bulk_data regulators[2];
|
||
|
|
struct bmc150_accel_interrupt interrupts[BMC150_ACCEL_INTERRUPTS];
|
||
|
|
struct bmc150_accel_trigger triggers[BMC150_ACCEL_TRIGGERS];
|
||
|
|
struct mutex mutex;
|
||
|
|
u8 fifo_mode, watermark;
|
||
|
|
s16 buffer[8];
|
||
|
|
/*
|
||
|
|
* Ensure there is sufficient space and correct alignment for
|
||
|
|
* the timestamp if enabled
|
||
|
|
*/
|
||
|
|
struct {
|
||
|
|
__le16 channels[3];
|
||
|
|
s64 ts __aligned(8);
|
||
|
|
} scan;
|
||
|
|
u8 bw_bits;
|
||
|
|
u32 slope_dur;
|
||
|
|
u32 slope_thres;
|
||
|
|
u32 range;
|
||
|
|
int ev_enable_state;
|
||
|
|
int64_t timestamp, old_timestamp; /* Only used in hw fifo mode. */
|
||
|
|
const struct bmc150_accel_chip_info *chip_info;
|
||
|
|
enum bmc150_type type;
|
||
|
|
struct i2c_client *second_device;
|
||
|
|
void (*resume_callback)(struct device *dev);
|
||
|
|
struct delayed_work resume_work;
|
||
|
|
struct iio_mount_matrix orientation;
|
||
|
|
};
|
||
|
|
|
||
|
|
int bmc150_accel_core_probe(struct device *dev, struct regmap *regmap, int irq,
|
||
|
|
enum bmc150_type type, const char *name,
|
||
|
|
bool block_supported);
|
||
|
|
void bmc150_accel_core_remove(struct device *dev);
|
||
|
|
extern const struct dev_pm_ops bmc150_accel_pm_ops;
|
||
|
|
extern const struct regmap_config bmc150_regmap_conf;
|
||
|
|
|
||
|
|
#endif /* _BMC150_ACCEL_H_ */
|