130 lines
3.0 KiB
YAML
130 lines
3.0 KiB
YAML
|
# SPDX-License-Identifier: GPL-2.0
|
||
|
|
%YAML 1.2
|
||
|
|
---
|
||
|
|
$id: http://devicetree.org/schemas/input/touchscreen/edt-ft5x06.yaml#
|
||
|
|
$schema: http://devicetree.org/meta-schemas/core.yaml#
|
||
|
|
|
||
|
|
title: FocalTech EDT-FT5x06 Polytouch
|
||
|
|
|
||
|
|
description: |
|
||
|
|
There are 5 variants of the chip for various touch panel sizes
|
||
|
|
FT5206GE1 2.8" .. 3.8"
|
||
|
|
FT5306DE4 4.3" .. 7"
|
||
|
|
FT5406EE8 7" .. 8.9"
|
||
|
|
FT5506EEG 7" .. 8.9"
|
||
|
|
FT5726NEI 5.7” .. 11.6"
|
||
|
|
|
||
|
|
maintainers:
|
||
|
|
- Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
||
|
|
|
||
|
|
allOf:
|
||
|
|
- $ref: touchscreen.yaml#
|
||
|
|
- if:
|
||
|
|
properties:
|
||
|
|
compatible:
|
||
|
|
contains:
|
||
|
|
enum:
|
||
|
|
- evervision,ev-ft5726
|
||
|
|
|
||
|
|
then:
|
||
|
|
properties:
|
||
|
|
offset-x: true
|
||
|
|
offset-y: true
|
||
|
|
|
||
|
|
properties:
|
||
|
|
compatible:
|
||
|
|
enum:
|
||
|
|
- edt,edt-ft5206
|
||
|
|
- edt,edt-ft5306
|
||
|
|
- edt,edt-ft5406
|
||
|
|
- edt,edt-ft5506
|
||
|
|
- evervision,ev-ft5726
|
||
|
|
- focaltech,ft6236
|
||
|
|
|
||
|
|
reg:
|
||
|
|
maxItems: 1
|
||
|
|
|
||
|
|
interrupts:
|
||
|
|
maxItems: 1
|
||
|
|
|
||
|
|
reset-gpios:
|
||
|
|
maxItems: 1
|
||
|
|
|
||
|
|
wake-gpios:
|
||
|
|
maxItems: 1
|
||
|
|
|
||
|
|
wakeup-source: true
|
||
|
|
|
||
|
|
vcc-supply: true
|
||
|
|
iovcc-supply: true
|
||
|
|
|
||
|
|
gain:
|
||
|
|
description: Allows setting the sensitivity in the range from 0 to 31.
|
||
|
|
Note that lower values indicate higher sensitivity.
|
||
|
|
$ref: /schemas/types.yaml#/definitions/uint32
|
||
|
|
minimum: 0
|
||
|
|
maximum: 31
|
||
|
|
|
||
|
|
offset:
|
||
|
|
description: Allows setting the edge compensation in the range from 0 to 31.
|
||
|
|
$ref: /schemas/types.yaml#/definitions/uint32
|
||
|
|
minimum: 0
|
||
|
|
maximum: 31
|
||
|
|
|
||
|
|
offset-x:
|
||
|
|
description: Same as offset, but applies only to the horizontal position.
|
||
|
|
Range from 0 to 80, only supported by evervision,ev-ft5726 devices.
|
||
|
|
$ref: /schemas/types.yaml#/definitions/uint32
|
||
|
|
minimum: 0
|
||
|
|
maximum: 80
|
||
|
|
|
||
|
|
offset-y:
|
||
|
|
description: Same as offset, but applies only to the vertical position.
|
||
|
|
Range from 0 to 80, only supported by evervision,ev-ft5726 devices.
|
||
|
|
$ref: /schemas/types.yaml#/definitions/uint32
|
||
|
|
minimum: 0
|
||
|
|
maximum: 80
|
||
|
|
|
||
|
|
report-rate-hz:
|
||
|
|
description: |
|
||
|
|
Allows setting the scan rate in Hertz.
|
||
|
|
M06 supports range from 30 to 140 Hz.
|
||
|
|
M12 supports range from 1 to 255 Hz.
|
||
|
|
minimum: 1
|
||
|
|
maximum: 255
|
||
|
|
|
||
|
|
touchscreen-size-x: true
|
||
|
|
touchscreen-size-y: true
|
||
|
|
touchscreen-fuzz-x: true
|
||
|
|
touchscreen-fuzz-y: true
|
||
|
|
touchscreen-inverted-x: true
|
||
|
|
touchscreen-inverted-y: true
|
||
|
|
touchscreen-swapped-x-y: true
|
||
|
|
interrupt-controller: true
|
||
|
|
|
||
|
|
additionalProperties: false
|
||
|
|
|
||
|
|
required:
|
||
|
|
- compatible
|
||
|
|
- reg
|
||
|
|
- interrupts
|
||
|
|
|
||
|
|
examples:
|
||
|
|
- |
|
||
|
|
#include <dt-bindings/gpio/gpio.h>
|
||
|
|
#include <dt-bindings/interrupt-controller/arm-gic.h>
|
||
|
|
i2c {
|
||
|
|
#address-cells = <1>;
|
||
|
|
#size-cells = <0>;
|
||
|
|
edt-ft5x06@38 {
|
||
|
|
compatible = "edt,edt-ft5406";
|
||
|
|
reg = <0x38>;
|
||
|
|
interrupt-parent = <&gpio2>;
|
||
|
|
interrupts = <5 IRQ_TYPE_EDGE_FALLING>;
|
||
|
|
reset-gpios = <&gpio2 6 GPIO_ACTIVE_LOW>;
|
||
|
|
wake-gpios = <&gpio4 9 GPIO_ACTIVE_HIGH>;
|
||
|
|
};
|
||
|
|
};
|
||
|
|
|
||
|
|
...
|