116 lines
3.1 KiB
YAML
116 lines
3.1 KiB
YAML
|
# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
|
||
|
|
%YAML 1.2
|
||
|
|
---
|
||
|
|
$id: http://devicetree.org/schemas/input/touchscreen/zinitix,bt400.yaml#
|
||
|
|
$schema: http://devicetree.org/meta-schemas/core.yaml#
|
||
|
|
|
||
|
|
title: Zinitix BT4xx and BT5xx series touchscreen controller
|
||
|
|
|
||
|
|
description: The Zinitix BT4xx and BT5xx series of touchscreen controllers
|
||
|
|
are Korea-produced touchscreens with embedded microcontrollers. The
|
||
|
|
BT4xx series was produced 2010-2013 and the BT5xx series 2013-2014.
|
||
|
|
|
||
|
|
maintainers:
|
||
|
|
- Michael Srba <Michael.Srba@seznam.cz>
|
||
|
|
- Linus Walleij <linus.walleij@linaro.org>
|
||
|
|
|
||
|
|
allOf:
|
||
|
|
- $ref: touchscreen.yaml#
|
||
|
|
|
||
|
|
properties:
|
||
|
|
$nodename:
|
||
|
|
pattern: "^touchscreen(@.*)?$"
|
||
|
|
|
||
|
|
compatible:
|
||
|
|
enum:
|
||
|
|
- zinitix,bt402
|
||
|
|
- zinitix,bt403
|
||
|
|
- zinitix,bt404
|
||
|
|
- zinitix,bt412
|
||
|
|
- zinitix,bt413
|
||
|
|
- zinitix,bt431
|
||
|
|
- zinitix,bt432
|
||
|
|
- zinitix,bt531
|
||
|
|
- zinitix,bt532
|
||
|
|
- zinitix,bt538
|
||
|
|
- zinitix,bt541
|
||
|
|
- zinitix,bt548
|
||
|
|
- zinitix,bt554
|
||
|
|
- zinitix,at100
|
||
|
|
|
||
|
|
reg:
|
||
|
|
description: I2C address on the I2C bus
|
||
|
|
|
||
|
|
clock-frequency:
|
||
|
|
description: I2C client clock frequency, defined for host when using
|
||
|
|
the device on the I2C bus
|
||
|
|
minimum: 0
|
||
|
|
maximum: 400000
|
||
|
|
|
||
|
|
interrupts:
|
||
|
|
description: Interrupt to host
|
||
|
|
maxItems: 1
|
||
|
|
|
||
|
|
vcca-supply:
|
||
|
|
description: Analog power supply regulator on the VCCA pin
|
||
|
|
|
||
|
|
vdd-supply:
|
||
|
|
description: Digital power supply regulator on the VDD pin.
|
||
|
|
In older device trees this can be the accidental name for the analog
|
||
|
|
supply on the VCCA pin, and in that case the deprecated vddo-supply is
|
||
|
|
used for the digital power supply.
|
||
|
|
|
||
|
|
vddo-supply:
|
||
|
|
description: Deprecated name for the digital power supply, use vdd-supply
|
||
|
|
as this reflects the real name of the pin. If this supply is present,
|
||
|
|
the vdd-supply represents VCCA instead of VDD. Implementers should first
|
||
|
|
check for this property, and if it is present assume that the vdd-supply
|
||
|
|
represents the analog supply.
|
||
|
|
deprecated: true
|
||
|
|
|
||
|
|
reset-gpios:
|
||
|
|
description: Reset line for the touchscreen, should be tagged
|
||
|
|
as GPIO_ACTIVE_LOW
|
||
|
|
|
||
|
|
zinitix,mode:
|
||
|
|
description: Mode of reporting touch points. Some modes may not work
|
||
|
|
with a particular ts firmware for unknown reasons. Available modes are
|
||
|
|
1 and 2. Mode 2 is the default and preferred.
|
||
|
|
$ref: /schemas/types.yaml#/definitions/uint32
|
||
|
|
enum: [1, 2]
|
||
|
|
|
||
|
|
touchscreen-size-x: true
|
||
|
|
touchscreen-size-y: true
|
||
|
|
touchscreen-fuzz-x: true
|
||
|
|
touchscreen-fuzz-y: true
|
||
|
|
|
||
|
|
additionalProperties: false
|
||
|
|
|
||
|
|
required:
|
||
|
|
- compatible
|
||
|
|
- reg
|
||
|
|
- interrupts
|
||
|
|
- touchscreen-size-x
|
||
|
|
- touchscreen-size-y
|
||
|
|
|
||
|
|
examples:
|
||
|
|
- |
|
||
|
|
#include <dt-bindings/interrupt-controller/irq.h>
|
||
|
|
#include <dt-bindings/gpio/gpio.h>
|
||
|
|
i2c {
|
||
|
|
#address-cells = <1>;
|
||
|
|
#size-cells = <0>;
|
||
|
|
|
||
|
|
touchscreen@20 {
|
||
|
|
compatible = "zinitix,bt541";
|
||
|
|
reg = <0x20>;
|
||
|
|
interrupt-parent = <&gpio>;
|
||
|
|
interrupts = <13 IRQ_TYPE_EDGE_FALLING>;
|
||
|
|
vcca-supply = <®_vcca_tsp>;
|
||
|
|
vdd-supply = <®_vdd_tsp>;
|
||
|
|
touchscreen-size-x = <540>;
|
||
|
|
touchscreen-size-y = <960>;
|
||
|
|
zinitix,mode = <2>;
|
||
|
|
};
|
||
|
|
};
|