63 lines
2.0 KiB
YAML
63 lines
2.0 KiB
YAML
|
# SPDX-License-Identifier: GPL-2.0
|
||
|
|
%YAML 1.2
|
||
|
|
---
|
||
|
|
$id: http://devicetree.org/schemas/serial/rs485.yaml#
|
||
|
|
$schema: http://devicetree.org/meta-schemas/core.yaml#
|
||
|
|
|
||
|
|
title: RS485 serial communications
|
||
|
|
|
||
|
|
description: The RTS signal is capable of automatically controlling line
|
||
|
|
direction for the built-in half-duplex mode. The properties described
|
||
|
|
hereafter shall be given to a half-duplex capable UART node.
|
||
|
|
|
||
|
|
maintainers:
|
||
|
|
- Rob Herring <robh@kernel.org>
|
||
|
|
|
||
|
|
properties:
|
||
|
|
rs485-rts-delay:
|
||
|
|
description: prop-encoded-array <a b>
|
||
|
|
$ref: /schemas/types.yaml#/definitions/uint32-array
|
||
|
|
items:
|
||
|
|
items:
|
||
|
|
- description: Delay between rts signal and beginning of data sent in
|
||
|
|
milliseconds. It corresponds to the delay before sending data.
|
||
|
|
default: 0
|
||
|
|
maximum: 100
|
||
|
|
- description: Delay between end of data sent and rts signal in milliseconds.
|
||
|
|
It corresponds to the delay after sending data and actual release
|
||
|
|
of the line.
|
||
|
|
default: 0
|
||
|
|
maximum: 100
|
||
|
|
|
||
|
|
rs485-rts-active-low:
|
||
|
|
description: drive RTS low when sending (default is high).
|
||
|
|
$ref: /schemas/types.yaml#/definitions/flag
|
||
|
|
|
||
|
|
rs485-rx-active-high:
|
||
|
|
description: Polarity of receiver enable signal (when separate from RTS).
|
||
|
|
True indicates active high (default is low).
|
||
|
|
$ref: /schemas/types.yaml#/definitions/flag
|
||
|
|
|
||
|
|
linux,rs485-enabled-at-boot-time:
|
||
|
|
description: enables the rs485 feature at boot time. It can be disabled
|
||
|
|
later with proper ioctl.
|
||
|
|
$ref: /schemas/types.yaml#/definitions/flag
|
||
|
|
|
||
|
|
rs485-rx-during-tx:
|
||
|
|
description: enables the receiving of data even while sending data.
|
||
|
|
$ref: /schemas/types.yaml#/definitions/flag
|
||
|
|
|
||
|
|
rs485-term-gpios:
|
||
|
|
description: GPIO pin to enable RS485 bus termination.
|
||
|
|
maxItems: 1
|
||
|
|
|
||
|
|
rs485-rx-during-tx-gpios:
|
||
|
|
description: Output GPIO pin that sets the state of rs485-rx-during-tx. This
|
||
|
|
signal can be used to control the RX part of an RS485 transceiver. Thereby
|
||
|
|
the active state enables RX during TX.
|
||
|
|
maxItems: 1
|
||
|
|
|
||
|
|
additionalProperties: true
|
||
|
|
|
||
|
|
...
|