123 lines
3.8 KiB
Plaintext
123 lines
3.8 KiB
Plaintext
|
# SPDX-License-Identifier: GPL-2.0-only
|
||
|
|
#
|
||
|
|
# Multiplexer I2C chip drivers configuration
|
||
|
|
#
|
||
|
|
|
||
|
|
menu "Multiplexer I2C Chip support"
|
||
|
|
depends on I2C_MUX
|
||
|
|
|
||
|
|
config I2C_ARB_GPIO_CHALLENGE
|
||
|
|
tristate "GPIO-based I2C arbitration"
|
||
|
|
depends on GPIOLIB || COMPILE_TEST
|
||
|
|
depends on OF
|
||
|
|
help
|
||
|
|
If you say yes to this option, support will be included for an
|
||
|
|
I2C multimaster arbitration scheme using GPIOs and a challenge &
|
||
|
|
response mechanism where masters have to claim the bus by asserting
|
||
|
|
a GPIO.
|
||
|
|
|
||
|
|
This driver can also be built as a module. If so, the module
|
||
|
|
will be called i2c-arb-gpio-challenge.
|
||
|
|
|
||
|
|
config I2C_MUX_GPIO
|
||
|
|
tristate "GPIO-based I2C multiplexer"
|
||
|
|
depends on GPIOLIB
|
||
|
|
help
|
||
|
|
If you say yes to this option, support will be included for a
|
||
|
|
GPIO based I2C multiplexer. This driver provides access to
|
||
|
|
I2C busses connected through a MUX, which is controlled
|
||
|
|
through GPIO pins.
|
||
|
|
|
||
|
|
This driver can also be built as a module. If so, the module
|
||
|
|
will be called i2c-mux-gpio.
|
||
|
|
|
||
|
|
config I2C_MUX_GPMUX
|
||
|
|
tristate "General Purpose I2C multiplexer"
|
||
|
|
select MULTIPLEXER
|
||
|
|
depends on OF
|
||
|
|
help
|
||
|
|
If you say yes to this option, support will be included for a
|
||
|
|
general purpose I2C multiplexer. This driver provides access to
|
||
|
|
I2C busses connected through a MUX, which in turn is controlled
|
||
|
|
by a MUX-controller from the MUX subsystem.
|
||
|
|
|
||
|
|
This driver can also be built as a module. If so, the module
|
||
|
|
will be called i2c-mux-gpmux.
|
||
|
|
|
||
|
|
config I2C_MUX_LTC4306
|
||
|
|
tristate "LTC LTC4306/5 I2C multiplexer"
|
||
|
|
select GPIOLIB
|
||
|
|
select REGMAP_I2C
|
||
|
|
help
|
||
|
|
If you say yes here you get support for the Analog Devices
|
||
|
|
LTC4306 or LTC4305 I2C mux/switch devices.
|
||
|
|
|
||
|
|
This driver can also be built as a module. If so, the module
|
||
|
|
will be called i2c-mux-ltc4306.
|
||
|
|
|
||
|
|
config I2C_MUX_PCA9541
|
||
|
|
tristate "NXP PCA9541 I2C Master Selector"
|
||
|
|
help
|
||
|
|
If you say yes here you get support for the NXP PCA9541
|
||
|
|
I2C Master Selector.
|
||
|
|
|
||
|
|
This driver can also be built as a module. If so, the module
|
||
|
|
will be called i2c-mux-pca9541.
|
||
|
|
|
||
|
|
config I2C_MUX_PCA954x
|
||
|
|
tristate "NXP PCA954x and PCA984x I2C Mux/switches"
|
||
|
|
depends on GPIOLIB || COMPILE_TEST
|
||
|
|
help
|
||
|
|
If you say yes here you get support for the NXP PCA954x
|
||
|
|
and PCA984x I2C mux/switch devices.
|
||
|
|
|
||
|
|
This driver can also be built as a module. If so, the module
|
||
|
|
will be called i2c-mux-pca954x.
|
||
|
|
|
||
|
|
config I2C_MUX_PINCTRL
|
||
|
|
tristate "pinctrl-based I2C multiplexer"
|
||
|
|
depends on PINCTRL
|
||
|
|
depends on OF
|
||
|
|
help
|
||
|
|
If you say yes to this option, support will be included for an I2C
|
||
|
|
multiplexer that uses the pinctrl subsystem, i.e. pin multiplexing.
|
||
|
|
This is useful for SoCs whose I2C module's signals can be routed to
|
||
|
|
different sets of pins at run-time.
|
||
|
|
|
||
|
|
This driver can also be built as a module. If so, the module will be
|
||
|
|
called i2c-mux-pinctrl.
|
||
|
|
|
||
|
|
config I2C_MUX_REG
|
||
|
|
tristate "Register-based I2C multiplexer"
|
||
|
|
depends on HAS_IOMEM
|
||
|
|
help
|
||
|
|
If you say yes to this option, support will be included for a
|
||
|
|
register based I2C multiplexer. This driver provides access to
|
||
|
|
I2C busses connected through a MUX, which is controlled
|
||
|
|
by a single register.
|
||
|
|
|
||
|
|
This driver can also be built as a module. If so, the module
|
||
|
|
will be called i2c-mux-reg.
|
||
|
|
|
||
|
|
config I2C_DEMUX_PINCTRL
|
||
|
|
tristate "pinctrl-based I2C demultiplexer"
|
||
|
|
depends on PINCTRL && OF
|
||
|
|
select OF_DYNAMIC
|
||
|
|
help
|
||
|
|
If you say yes to this option, support will be included for an I2C
|
||
|
|
demultiplexer that uses the pinctrl subsystem. This is useful if you
|
||
|
|
want to change the I2C master at run-time depending on features.
|
||
|
|
|
||
|
|
config I2C_MUX_MLXCPLD
|
||
|
|
tristate "Mellanox CPLD based I2C multiplexer"
|
||
|
|
help
|
||
|
|
If you say yes to this option, support will be included for a
|
||
|
|
CPLD based I2C multiplexer. This driver provides access to
|
||
|
|
I2C busses connected through a MUX, which is controlled
|
||
|
|
by a CPLD register.
|
||
|
|
|
||
|
|
This driver can also be built as a module. If so, the module
|
||
|
|
will be called i2c-mux-mlxcpld.
|
||
|
|
|
||
|
|
endmenu
|