# SPDX-License-Identifier: GPL-2.0-only menuconfig CAN_DEV tristate "CAN Device Drivers" default y depends on CAN help Controller Area Network (CAN) is serial communications protocol up to 1Mbit/s for its original release (now known as Classical CAN) and up to 8Mbit/s for the more recent CAN with Flexible Data-Rate (CAN-FD). The CAN bus was originally mainly for automotive, but is now widely used in marine (NMEA2000), industrial, and medical applications. More information on the CAN network protocol family PF_CAN is contained in . This section contains all the CAN(-FD) device drivers including the virtual ones. If you own such devices or plan to use the virtual CAN interfaces to develop applications, say Y here. To compile as a module, choose M here: the module will be called can-dev. if CAN_DEV config CAN_VCAN tristate "Virtual Local CAN Interface (vcan)" help Similar to the network loopback devices, vcan offers a virtual local CAN interface. This driver can also be built as a module. If so, the module will be called vcan. config CAN_VXCAN tristate "Virtual CAN Tunnel (vxcan)" help Similar to the virtual ethernet driver veth, vxcan implements a local CAN traffic tunnel between two virtual CAN network devices. When creating a vxcan, two vxcan devices are created as pair. When one end receives the packet it appears on its pair and vice versa. The vxcan can be used for cross namespace communication. In opposite to vcan loopback devices the vxcan only forwards CAN frames to its pair and does *not* provide a local echo of sent CAN frames. To disable a potential echo in af_can.c the vxcan driver announces IFF_ECHO in the interface flags. To have a clean start in each namespace the CAN GW hop counter is set to zero. This driver can also be built as a module. If so, the module will be called vxcan. config CAN_NETLINK bool "CAN device drivers with Netlink support" default y help Enables the common framework for CAN device drivers. This is the standard library and provides features for the Netlink interface such as bittiming validation, support of CAN error states, device restart and others. The additional features selected by this option will be added to the can-dev module. This is required by all platform and hardware CAN drivers. If you plan to use such devices or if unsure, say Y. if CAN_NETLINK config CAN_CALC_BITTIMING bool "CAN bit-timing calculation" default y help If enabled, CAN bit-timing parameters will be calculated for the bit-rate specified via Netlink argument "bitrate" when the device get started. This works fine for the most common CAN controllers with standard bit-rates but may fail for exotic bit-rates or CAN source clock frequencies. Disabling saves some space, but then the bit-timing parameters must be specified directly using the Netlink arguments "tq", "prop_seg", "phase_seg1", "phase_seg2" and "sjw". The additional features selected by this option will be added to the can-dev module. If unsure, say Y. config CAN_RX_OFFLOAD bool config CAN_AT91 tristate "Atmel AT91 onchip CAN controller" depends on (ARCH_AT91 || COMPILE_TEST) && HAS_IOMEM help This is a driver for the SoC CAN controller in Atmel's AT91SAM9263 and AT91SAM9X5 processors. config CAN_BXCAN tristate "STM32 Basic Extended CAN (bxCAN) devices" depends on ARCH_STM32 || COMPILE_TEST depends on HAS_IOMEM select CAN_RX_OFFLOAD help Say yes here to build support for the STMicroelectronics STM32 basic extended CAN Controller (bxCAN). This driver can also be built as a module. If so, the module will be called bxcan. config CAN_CAN327 tristate "Serial / USB serial ELM327 based OBD-II Interfaces (can327)" depends on TTY select CAN_RX_OFFLOAD help CAN driver for several 'low cost' OBD-II interfaces based on the ELM327 OBD-II interpreter chip. This is a best effort driver - the ELM327 interface was never designed to be used as a standalone CAN interface. However, it can still be used for simple request-response protocols (such as OBD II), and to monitor broadcast messages on a bus (such as in a vehicle). Please refer to the documentation for information on how to use it: Documentation/networking/device_drivers/can/can327.rst If this driver is built as a module, it will be called can327. config CAN_FLEXCAN tristate "Support for Freescale FLEXCAN based chips" depends on OF || COLDFIRE || COMPILE_TEST depends on HAS_IOMEM select CAN_RX_OFFLOAD help Say Y here if you want to support for Freescale FlexCAN. config CAN_GRCAN tristate "Aeroflex Gaisler GRCAN and GRHCAN CAN devices" depends on OF && HAS_DMA && HAS_IOMEM help Say Y here if you want to use Aeroflex Gaisler GRCAN or GRHCAN. Note that the driver supports little endian, even though little endian syntheses of the cores would need some modifications on the hardware level to work. config CAN_JANZ_ICAN3 tristate "Janz VMOD-ICAN3 Intelligent CAN controller" depends on MFD_JANZ_CMODIO help Driver for Janz VMOD-ICAN3 Intelligent CAN controller module, which connects to a MODULbus carrier board. This driver can also be built as a module. If so, the module will be called janz-ican3.ko. config CAN_KVASER_PCIEFD depends on PCI tristate "Kvaser PCIe FD cards" help This is a driver for the Kvaser PCI Express CAN FD family. Supported devices: Kvaser PCIEcan 4xHS Kvaser PCIEcan 2xHS v2 Kvaser PCIEcan HS v2 Kvaser Mini PCI Express HS v2 Kvaser Mini PCI Express 2xHS v2 config CAN_SLCAN tristate "Serial / USB serial CAN Adaptors (slcan)" depends on TTY help CAN driver for several 'low cost' CAN interfaces that are attached via serial lines or via USB-to-serial adapters using the LAWICEL ASCII protocol. The driver implements the tty linediscipline N_SLCAN. As only the sending and receiving of CAN frames is implemented, this driver should work with the (serial/USB) CAN hardware from: www.canusb.com / www.can232.com / www.mictronics.de / www.canhack.de Userspace tools to attach the SLCAN line discipline (slcan_attach, slcand) can be found in the can-utils at the linux-can project, see https://github.com/linux-can/can-utils for details. The slcan driver supports up to 10 CAN netdevices by default which can be changed by the 'maxdev=xx' module option. This driver can also be built as a module. If so, the module will be called slcan. config CAN_SUN4I tristate "Allwinner A10 CAN controller" depends on MACH_SUN4I || MACH_SUN7I || RISCV || COMPILE_TEST help Say Y here if you want to use CAN controller found on Allwinner A10/A20/D1 SoCs. To compile this driver as a module, choose M here: the module will be called sun4i_can. config CAN_TI_HECC depends on ARM tristate "TI High End CAN Controller" select CAN_RX_OFFLOAD help Driver for TI HECC (High End CAN Controller) module found on many TI devices. The device specifications are available from www.ti.com config CAN_XILINXCAN tristate "Xilinx CAN" depends on ARCH_ZYNQ || ARM64 || MICROBLAZE || COMPILE_TEST depends on COMMON_CLK && HAS_IOMEM help Xilinx CAN driver. This driver supports both soft AXI CAN IP and Zynq CANPS IP. source "drivers/net/can/c_can/Kconfig" source "drivers/net/can/cc770/Kconfig" source "drivers/net/can/ctucanfd/Kconfig" source "drivers/net/can/ifi_canfd/Kconfig" source "drivers/net/can/m_can/Kconfig" source "drivers/net/can/mscan/Kconfig" source "drivers/net/can/peak_canfd/Kconfig" source "drivers/net/can/rcar/Kconfig" source "drivers/net/can/sja1000/Kconfig" source "drivers/net/can/softing/Kconfig" source "drivers/net/can/spi/Kconfig" source "drivers/net/can/usb/Kconfig" endif #CAN_NETLINK config CAN_DEBUG_DEVICES bool "CAN devices debugging messages" help Say Y here if you want the CAN device drivers to produce a bunch of debug messages to the system log. Select this if you are having a problem with CAN support and want to see more of what is going on. endif #CAN_DEV