# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
%YAML 1.2
---
$id: http://devicetree.org/schemas/net/dsa/nxp,sja1105.yaml#
$schema: http://devicetree.org/meta-schemas/core.yaml#

title: NXP SJA1105 Automotive Ethernet Switch Family

description:
  The SJA1105 SPI interface requires a CS-to-CLK time (t2 in UM10944.pdf) of at
  least one half of t_CLK. At an SPI frequency of 1MHz, this means a minimum
  cs_sck_delay of 500ns. Ensuring that this SPI timing requirement is observed
  depends on the SPI bus master driver.

allOf:
  - $ref: dsa.yaml#/$defs/ethernet-ports
  - $ref: /schemas/spi/spi-peripheral-props.yaml#

maintainers:
  - Vladimir Oltean <vladimir.oltean@nxp.com>

properties:
  compatible:
    enum:
      - nxp,sja1105e
      - nxp,sja1105t
      - nxp,sja1105p
      - nxp,sja1105q
      - nxp,sja1105r
      - nxp,sja1105s
      - nxp,sja1110a
      - nxp,sja1110b
      - nxp,sja1110c
      - nxp,sja1110d

  reg:
    maxItems: 1

  # Optional container node for the 2 internal MDIO buses of the SJA1110
  # (one for the internal 100base-T1 PHYs and the other for the single
  # 100base-TX PHY). The "reg" property does not have physical significance.
  # The PHY addresses to port correspondence is as follows: for 100base-T1,
  # port 5 has PHY 1, port 6 has PHY 2 etc, while for 100base-TX, port 1 has
  # PHY 1.
  mdios:
    type: object

    properties:
      '#address-cells':
        const: 1
      '#size-cells':
        const: 0

    patternProperties:
      "^mdio@[0-1]$":
        $ref: /schemas/net/mdio.yaml#
        unevaluatedProperties: false

        properties:
          compatible:
            oneOf:
              - enum:
                  - nxp,sja1110-base-t1-mdio
                  - nxp,sja1110-base-tx-mdio

          reg:
            oneOf:
              - enum:
                  - 0
                  - 1

        required:
          - compatible
          - reg

patternProperties:
  "^(ethernet-)?ports$":
    patternProperties:
      "^(ethernet-)?port@[0-9]+$":
        allOf:
          - if:
              properties:
                phy-mode:
                  contains:
                    enum:
                      - rgmii
                      - rgmii-rxid
                      - rgmii-txid
                      - rgmii-id
            then:
              properties:
                rx-internal-delay-ps:
                  $ref: "#/$defs/internal-delay-ps"
                tx-internal-delay-ps:
                  $ref: "#/$defs/internal-delay-ps"

required:
  - compatible
  - reg

$defs:
  internal-delay-ps:
    description:
      Disable tunable delay lines using 0 ps, or enable them and select
      the phase between 1640 ps (73.8 degree shift at 1Gbps) and 2260 ps
      (101.7 degree shift) in increments of 0.9 degrees (20 ps).
    enum:
      [0, 1640, 1660, 1680, 1700, 1720, 1740, 1760, 1780, 1800, 1820, 1840,
       1860, 1880, 1900, 1920, 1940, 1960, 1980, 2000, 2020, 2040, 2060, 2080,
       2100, 2120, 2140, 2160, 2180, 2200, 2220, 2240, 2260]

unevaluatedProperties: false

examples:
  - |
    spi {
            #address-cells = <1>;
            #size-cells = <0>;

            ethernet-switch@1 {
                    reg = <0x1>;
                    compatible = "nxp,sja1105t";

                    ethernet-ports {
                            #address-cells = <1>;
                            #size-cells = <0>;

                            port@0 {
                                    phy-handle = <&rgmii_phy6>;
                                    phy-mode = "rgmii-id";
                                    rx-internal-delay-ps = <0>;
                                    tx-internal-delay-ps = <0>;
                                    reg = <0>;
                            };

                            port@1 {
                                    phy-handle = <&rgmii_phy3>;
                                    phy-mode = "rgmii-id";
                                    rx-internal-delay-ps = <0>;
                                    tx-internal-delay-ps = <0>;
                                    reg = <1>;
                            };

                            port@2 {
                                    phy-handle = <&rgmii_phy4>;
                                    phy-mode = "rgmii-id";
                                    rx-internal-delay-ps = <0>;
                                    tx-internal-delay-ps = <0>;
                                    reg = <2>;
                            };

                            port@3 {
                                    phy-handle = <&rgmii_phy4>;
                                    phy-mode = "rgmii-id";
                                    rx-internal-delay-ps = <0>;
                                    tx-internal-delay-ps = <0>;
                                    reg = <3>;
                            };

                            port@4 {
                                    ethernet = <&enet2>;
                                    phy-mode = "rgmii";
                                    rx-internal-delay-ps = <0>;
                                    tx-internal-delay-ps = <0>;
                                    reg = <4>;

                                    fixed-link {
                                            speed = <1000>;
                                            full-duplex;
                                    };
                            };
                    };
            };
    };