110 lines
2.9 KiB
YAML
110 lines
2.9 KiB
YAML
# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
|
|
%YAML 1.2
|
|
---
|
|
$id: http://devicetree.org/schemas/input/ti,drv260x.yaml#
|
|
$schema: http://devicetree.org/meta-schemas/core.yaml#
|
|
|
|
title: Texas Instruments - drv260x Haptics driver family
|
|
|
|
maintainers:
|
|
- Andrew Davis <afd@ti.com>
|
|
|
|
properties:
|
|
compatible:
|
|
enum:
|
|
- ti,drv2604
|
|
- ti,drv2605
|
|
- ti,drv2605l
|
|
|
|
reg:
|
|
maxItems: 1
|
|
|
|
vbat-supply:
|
|
description: Power supply to the haptic motor
|
|
|
|
# TODO: Deprecate 'mode' in favor of differently named property
|
|
mode:
|
|
$ref: /schemas/types.yaml#/definitions/uint32
|
|
description: |
|
|
Power up mode of the chip
|
|
(defined in include/dt-bindings/input/ti-drv260x.h)
|
|
|
|
DRV260X_LRA_MODE
|
|
Linear Resonance Actuator mode (Piezoelectric)
|
|
|
|
DRV260X_LRA_NO_CAL_MODE
|
|
This is a LRA Mode but there is no calibration sequence during init.
|
|
And the device is configured for real time playback mode (RTP mode).
|
|
|
|
DRV260X_ERM_MODE
|
|
Eccentric Rotating Mass mode (Rotary vibrator)
|
|
enum: [ 0, 1, 2 ]
|
|
|
|
library-sel:
|
|
$ref: /schemas/types.yaml#/definitions/uint32
|
|
description: |
|
|
These are ROM based waveforms pre-programmed into the IC.
|
|
This should be set to set the library to use at power up.
|
|
(defined in include/dt-bindings/input/ti-drv260x.h)
|
|
|
|
DRV260X_LIB_EMPTY - Do not use a pre-programmed library
|
|
DRV260X_ERM_LIB_A - Pre-programmed Library
|
|
DRV260X_ERM_LIB_B - Pre-programmed Library
|
|
DRV260X_ERM_LIB_C - Pre-programmed Library
|
|
DRV260X_ERM_LIB_D - Pre-programmed Library
|
|
DRV260X_ERM_LIB_E - Pre-programmed Library
|
|
DRV260X_ERM_LIB_F - Pre-programmed Library
|
|
DRV260X_LIB_LRA - Pre-programmed LRA Library
|
|
enum: [ 0, 1, 2, 3, 4, 5, 6, 7 ]
|
|
|
|
enable-gpio:
|
|
maxItems: 1
|
|
deprecated: true
|
|
|
|
enable-gpios:
|
|
maxItems: 1
|
|
|
|
vib-rated-mv:
|
|
$ref: /schemas/types.yaml#/definitions/uint32
|
|
description: |
|
|
The rated voltage of the actuator in millivolts.
|
|
If this is not set then the value will be defaulted to 3200 mV.
|
|
default: 3200
|
|
|
|
vib-overdrive-mv:
|
|
$ref: /schemas/types.yaml#/definitions/uint32
|
|
description: |
|
|
The overdrive voltage of the actuator in millivolts.
|
|
If this is not set then the value will be defaulted to 3200 mV.
|
|
default: 3200
|
|
|
|
required:
|
|
- compatible
|
|
- reg
|
|
- enable-gpios
|
|
- mode
|
|
- library-sel
|
|
|
|
additionalProperties: false
|
|
|
|
examples:
|
|
- |
|
|
#include <dt-bindings/gpio/gpio.h>
|
|
#include <dt-bindings/input/ti-drv260x.h>
|
|
|
|
i2c {
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
haptics@5a {
|
|
compatible = "ti,drv2605l";
|
|
reg = <0x5a>;
|
|
vbat-supply = <&vbat>;
|
|
enable-gpios = <&gpio1 28 GPIO_ACTIVE_HIGH>;
|
|
mode = <DRV260X_LRA_MODE>;
|
|
library-sel = <DRV260X_LIB_LRA>;
|
|
vib-rated-mv = <3200>;
|
|
vib-overdrive-mv = <3200>;
|
|
};
|
|
};
|