155 lines
3.9 KiB
YAML
155 lines
3.9 KiB
YAML
# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
|
|
# Copyright (c) 2020 MediaTek Inc.
|
|
%YAML 1.2
|
|
---
|
|
$id: http://devicetree.org/schemas/media/i2c/ovti,ov02a10.yaml#
|
|
$schema: http://devicetree.org/meta-schemas/core.yaml#
|
|
|
|
title: Omnivision OV02A10 CMOS Sensor
|
|
|
|
maintainers:
|
|
- Dongchun Zhu <dongchun.zhu@mediatek.com>
|
|
|
|
description: |-
|
|
The Omnivision OV02A10 is a low-cost, high performance, 1/5-inch, 2 megapixel
|
|
image sensor, which is the latest production derived from Omnivision's CMOS
|
|
image sensor technology. Ihis chip supports high frame rate speeds up to 30fps
|
|
@ 1600x1200 (UXGA) resolution transferred over a 1-lane MIPI interface. The
|
|
sensor output is available via CSI-2 serial data output.
|
|
|
|
allOf:
|
|
- $ref: /schemas/media/video-interface-devices.yaml#
|
|
|
|
properties:
|
|
compatible:
|
|
const: ovti,ov02a10
|
|
|
|
reg:
|
|
maxItems: 1
|
|
|
|
clocks:
|
|
maxItems: 1
|
|
|
|
clock-names:
|
|
description:
|
|
External clock for the sensor.
|
|
items:
|
|
- const: eclk
|
|
|
|
clock-frequency:
|
|
description:
|
|
Frequency of the eclk clock in Hz.
|
|
|
|
dovdd-supply:
|
|
description:
|
|
Definition of the regulator used as Digital I/O voltage supply.
|
|
|
|
avdd-supply:
|
|
description:
|
|
Definition of the regulator used as Analog voltage supply.
|
|
|
|
dvdd-supply:
|
|
description:
|
|
Definition of the regulator used as Digital core voltage supply.
|
|
|
|
powerdown-gpios:
|
|
description:
|
|
Must be the device tree identifier of the GPIO connected to the
|
|
PD_PAD pin. This pin is used to place the OV02A10 into standby mode
|
|
or shutdown mode. As the line needs to be high for the powerdown mode
|
|
to be active, it should be marked GPIO_ACTIVE_HIGH.
|
|
maxItems: 1
|
|
|
|
reset-gpios:
|
|
description:
|
|
Must be the device tree identifier of the GPIO connected to the
|
|
RST_PD pin. If specified, it will be asserted during driver probe.
|
|
As the line needs to be low for the reset to be active, it should be
|
|
marked GPIO_ACTIVE_LOW.
|
|
maxItems: 1
|
|
|
|
rotation:
|
|
enum:
|
|
- 0 # Sensor Mounted Upright
|
|
- 180 # Sensor Mounted Upside Down
|
|
default: 0
|
|
|
|
port:
|
|
$ref: /schemas/graph.yaml#/$defs/port-base
|
|
additionalProperties: false
|
|
description:
|
|
Output port node, single endpoint describing the CSI-2 transmitter.
|
|
|
|
properties:
|
|
endpoint:
|
|
$ref: /schemas/media/video-interfaces.yaml#
|
|
unevaluatedProperties: false
|
|
|
|
properties:
|
|
link-frequencies: true
|
|
ovti,mipi-clock-voltage:
|
|
$ref: /schemas/types.yaml#/definitions/uint32
|
|
description:
|
|
Definition of MIPI clock voltage unit. This entry corresponds to
|
|
the link speed defined by the 'link-frequencies' property.
|
|
If present, the value shall be in the range of 0-4.
|
|
default: 4
|
|
|
|
required:
|
|
- link-frequencies
|
|
|
|
required:
|
|
- endpoint
|
|
|
|
required:
|
|
- compatible
|
|
- reg
|
|
- clocks
|
|
- clock-names
|
|
- clock-frequency
|
|
- dovdd-supply
|
|
- avdd-supply
|
|
- dvdd-supply
|
|
- powerdown-gpios
|
|
- reset-gpios
|
|
- port
|
|
|
|
additionalProperties: false
|
|
|
|
examples:
|
|
- |
|
|
#include <dt-bindings/gpio/gpio.h>
|
|
|
|
i2c {
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
ov02a10: camera-sensor@3d {
|
|
compatible = "ovti,ov02a10";
|
|
reg = <0x3d>;
|
|
|
|
powerdown-gpios = <&pio 107 GPIO_ACTIVE_HIGH>;
|
|
reset-gpios = <&pio 109 GPIO_ACTIVE_LOW>;
|
|
|
|
clocks = <&ov02a10_clk>;
|
|
clock-names = "eclk";
|
|
clock-frequency = <24000000>;
|
|
|
|
rotation = <180>;
|
|
|
|
dovdd-supply = <&ov02a10_dovdd>;
|
|
avdd-supply = <&ov02a10_avdd>;
|
|
dvdd-supply = <&ov02a10_dvdd>;
|
|
|
|
port {
|
|
wcam_out: endpoint {
|
|
link-frequencies = /bits/ 64 <390000000>;
|
|
ovti,mipi-clock-voltage = <3>;
|
|
remote-endpoint = <&mipi_in_wcam>;
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
...
|