99 lines
3.6 KiB
Plaintext
99 lines
3.6 KiB
Plaintext
TI PHY: DT DOCUMENTATION FOR PHYs in TI PLATFORMs
|
|
|
|
OMAP CONTROL PHY
|
|
|
|
Required properties:
|
|
- compatible: Should be one of
|
|
"ti,control-phy-otghs" - if it has otghs_control mailbox register as on OMAP4.
|
|
"ti,control-phy-usb2" - if it has Power down bit in control_dev_conf register
|
|
e.g. USB2_PHY on OMAP5.
|
|
"ti,control-phy-pipe3" - if it has DPLL and individual Rx & Tx power control
|
|
e.g. USB3 PHY and SATA PHY on OMAP5.
|
|
"ti,control-phy-pcie" - for pcie to support external clock for pcie and to
|
|
set PCS delay value.
|
|
e.g. PCIE PHY in DRA7x
|
|
"ti,control-phy-usb2-dra7" - if it has power down register like USB2 PHY on
|
|
DRA7 platform.
|
|
"ti,control-phy-usb2-am437" - if it has power down register like USB2 PHY on
|
|
AM437 platform.
|
|
- reg : register ranges as listed in the reg-names property
|
|
- reg-names: "otghs_control" for control-phy-otghs
|
|
"power", "pcie_pcs" and "control_sma" for control-phy-pcie
|
|
"power" for all other types
|
|
|
|
omap_control_usb: omap-control-usb@4a002300 {
|
|
compatible = "ti,control-phy-otghs";
|
|
reg = <0x4a00233c 0x4>;
|
|
reg-names = "otghs_control";
|
|
};
|
|
|
|
TI PIPE3 PHY
|
|
|
|
Required properties:
|
|
- compatible: Should be "ti,phy-usb3", "ti,phy-pipe3-sata" or
|
|
"ti,phy-pipe3-pcie. "ti,omap-usb3" is deprecated.
|
|
- reg : Address and length of the register set for the device.
|
|
- reg-names: The names of the register addresses corresponding to the registers
|
|
filled in "reg".
|
|
- #phy-cells: determine the number of cells that should be given in the
|
|
phandle while referencing this phy.
|
|
- clocks: a list of phandles and clock-specifier pairs, one for each entry in
|
|
clock-names.
|
|
- clock-names: should include:
|
|
* "wkupclk" - wakeup clock.
|
|
* "sysclk" - system clock.
|
|
* "refclk" - reference clock.
|
|
* "dpll_ref" - external dpll ref clk
|
|
* "dpll_ref_m2" - external dpll ref clk
|
|
* "phy-div" - divider for apll
|
|
* "div-clk" - apll clock
|
|
|
|
Optional properties:
|
|
- id: If there are multiple instance of the same type, in order to
|
|
differentiate between each instance "id" can be used (e.g., multi-lane PCIe
|
|
PHY). If "id" is not provided, it is set to default value of '1'.
|
|
- syscon-pllreset: Handle to system control region that contains the
|
|
CTRL_CORE_SMA_SW_0 register and register offset to the CTRL_CORE_SMA_SW_0
|
|
register that contains the SATA_PLL_SOFT_RESET bit. Only valid for sata_phy.
|
|
- syscon-pcs : phandle/offset pair. Phandle to the system control module and the
|
|
register offset to write the PCS delay value.
|
|
|
|
Deprecated properties:
|
|
- ctrl-module : phandle of the control module used by PHY driver to power on
|
|
the PHY.
|
|
|
|
Recommended properies:
|
|
- syscon-phy-power : phandle/offset pair. Phandle to the system control
|
|
module and the register offset to power on/off the PHY.
|
|
|
|
This is usually a subnode of ocp2scp to which it is connected.
|
|
|
|
usb3phy@4a084400 {
|
|
compatible = "ti,phy-usb3";
|
|
reg = <0x4a084400 0x80>,
|
|
<0x4a084800 0x64>,
|
|
<0x4a084c00 0x40>;
|
|
reg-names = "phy_rx", "phy_tx", "pll_ctrl";
|
|
ctrl-module = <&omap_control_usb>;
|
|
#phy-cells = <0>;
|
|
clocks = <&usb_phy_cm_clk32k>,
|
|
<&sys_clkin>,
|
|
<&usb_otg_ss_refclk960m>;
|
|
clock-names = "wkupclk",
|
|
"sysclk",
|
|
"refclk";
|
|
};
|
|
|
|
sata_phy: phy@4a096000 {
|
|
compatible = "ti,phy-pipe3-sata";
|
|
reg = <0x4A096000 0x80>, /* phy_rx */
|
|
<0x4A096400 0x64>, /* phy_tx */
|
|
<0x4A096800 0x40>; /* pll_ctrl */
|
|
reg-names = "phy_rx", "phy_tx", "pll_ctrl";
|
|
ctrl-module = <&omap_control_sata>;
|
|
clocks = <&sys_clkin1>, <&sata_ref_clk>;
|
|
clock-names = "sysclk", "refclk";
|
|
syscon-pllreset = <&scm_conf 0x3fc>;
|
|
#phy-cells = <0>;
|
|
};
|