linux-zen-desktop/drivers/atm/midway.h

267 lines
7.6 KiB
C

/* SPDX-License-Identifier: GPL-2.0 */
/* drivers/atm/midway.h - Efficient Networks Midway (SAR) description */
/* Written 1995-1999 by Werner Almesberger, EPFL LRC/ICA */
#ifndef DRIVERS_ATM_MIDWAY_H
#define DRIVERS_ATM_MIDWAY_H
#define NR_VCI 1024 /* number of VCIs */
#define NR_VCI_LD 10 /* log2(NR_VCI) */
#define NR_DMA_RX 512 /* RX DMA queue entries */
#define NR_DMA_TX 512 /* TX DMA queue entries */
#define NR_SERVICE NR_VCI /* service list size */
#define NR_CHAN 8 /* number of TX channels */
#define TS_CLOCK 25000000 /* traffic shaper clock (cell/sec) */
#define MAP_MAX_SIZE 0x00400000 /* memory window for max config */
#define EPROM_SIZE 0x00010000
#define MEM_VALID 0xffc00000 /* mask base address with this */
#define PHY_BASE 0x00020000 /* offset of PHY register are */
#define REG_BASE 0x00040000 /* offset of Midway register area */
#define RAM_BASE 0x00200000 /* offset of RAM area */
#define RAM_INCREMENT 0x00020000 /* probe for RAM every 128kB */
#define MID_VCI_BASE RAM_BASE
#define MID_DMA_RX_BASE (MID_VCI_BASE+NR_VCI*16)
#define MID_DMA_TX_BASE (MID_DMA_RX_BASE+NR_DMA_RX*8)
#define MID_SERVICE_BASE (MID_DMA_TX_BASE+NR_DMA_TX*8)
#define MID_FREE_BASE (MID_SERVICE_BASE+NR_SERVICE*4)
#define MAC_LEN 6 /* atm.h */
#define MID_MIN_BUF_SIZE (1024) /* 1 kB is minimum */
#define MID_MAX_BUF_SIZE (128*1024) /* 128 kB is maximum */
#define RX_DESCR_SIZE 1 /* RX PDU descr is 1 longword */
#define TX_DESCR_SIZE 2 /* TX PDU descr is 2 longwords */
#define AAL5_TRAILER (ATM_AAL5_TRAILER/4) /* AAL5 trailer is 2 longwords */
#define TX_GAP 8 /* TX buffer gap (words) */
/*
* Midway Reset/ID
*
* All values read-only. Writing to this register resets Midway chip.
*/
#define MID_RES_ID_MCON 0x00 /* Midway Reset/ID */
#define MID_ID 0xf0000000 /* Midway version */
#define MID_SHIFT 24
#define MID_MOTHER_ID 0x00000700 /* mother board id */
#define MID_MOTHER_SHIFT 8
#define MID_CON_TI 0x00000080 /* 0: normal ctrl; 1: SABRE */
#define MID_CON_SUNI 0x00000040 /* 0: UTOPIA; 1: SUNI */
#define MID_CON_V6 0x00000020 /* 0: non-pipel UTOPIA (required iff
!CON_SUNI; 1: UTOPIA */
#define DAUGHTER_ID 0x0000001f /* daughter board id */
/*
* Interrupt Status Acknowledge, Interrupt Status & Interrupt Enable
*/
#define MID_ISA 0x01 /* Interrupt Status Acknowledge */
#define MID_IS 0x02 /* Interrupt Status */
#define MID_IE 0x03 /* Interrupt Enable */
#define MID_TX_COMPLETE_7 0x00010000 /* channel N completed a PDU */
#define MID_TX_COMPLETE_6 0x00008000 /* transmission */
#define MID_TX_COMPLETE_5 0x00004000
#define MID_TX_COMPLETE_4 0x00002000
#define MID_TX_COMPLETE_3 0x00001000
#define MID_TX_COMPLETE_2 0x00000800
#define MID_TX_COMPLETE_1 0x00000400
#define MID_TX_COMPLETE_0 0x00000200
#define MID_TX_COMPLETE 0x0001fe00 /* any TX */
#define MID_TX_DMA_OVFL 0x00000100 /* DMA to adapter overflow */
#define MID_TX_IDENT_MISM 0x00000080 /* TX: ident mismatch => halted */
#define MID_DMA_LERR_ACK 0x00000040 /* LERR - SBus ? */
#define MID_DMA_ERR_ACK 0x00000020 /* DMA error */
#define MID_RX_DMA_COMPLETE 0x00000010 /* DMA to host done */
#define MID_TX_DMA_COMPLETE 0x00000008 /* DMA from host done */
#define MID_SERVICE 0x00000004 /* something in service list */
#define MID_SUNI_INT 0x00000002 /* interrupt from SUNI */
#define MID_STAT_OVFL 0x00000001 /* statistics overflow */
/*
* Master Control/Status
*/
#define MID_MC_S 0x04
#define MID_INT_SELECT 0x000001C0 /* Interrupt level (000: off) */
#define MID_INT_SEL_SHIFT 6
#define MID_TX_LOCK_MODE 0x00000020 /* 0: streaming; 1: TX ovfl->lock */
#define MID_DMA_ENABLE 0x00000010 /* R: 0: disable; 1: enable
W: 0: no change; 1: enable */
#define MID_TX_ENABLE 0x00000008 /* R: 0: TX disabled; 1: enabled
W: 0: no change; 1: enable */
#define MID_RX_ENABLE 0x00000004 /* like TX */
#define MID_WAIT_1MS 0x00000002 /* R: 0: timer not running; 1: running
W: 0: no change; 1: no interrupts
for 1 ms */
#define MID_WAIT_500US 0x00000001 /* like WAIT_1MS, but 0.5 ms */
/*
* Statistics
*
* Cleared when reading.
*/
#define MID_STAT 0x05
#define MID_VCI_TRASH 0xFFFF0000 /* trashed cells because of VCI mode */
#define MID_VCI_TRASH_SHIFT 16
#define MID_OVFL_TRASH 0x0000FFFF /* trashed cells because of overflow */
/*
* Address registers
*/
#define MID_SERV_WRITE 0x06 /* free pos in service area (R, 10 bits) */
#define MID_DMA_ADDR 0x07 /* virtual DMA address (R, 32 bits) */
#define MID_DMA_WR_RX 0x08 /* (RW, 9 bits) */
#define MID_DMA_RD_RX 0x09
#define MID_DMA_WR_TX 0x0A
#define MID_DMA_RD_TX 0x0B
/*
* Transmit Place Registers (0x10+4*channel)
*/
#define MID_TX_PLACE(c) (0x10+4*(c))
#define MID_SIZE 0x00003800 /* size, N*256 x 32 bit */
#define MID_SIZE_SHIFT 11
#define MID_LOCATION 0x000007FF /* location in adapter memory (word) */
#define MID_LOC_SKIP 8 /* 8 bits of location are always zero
(applies to all uses of location) */
/*
* Transmit ReadPtr Registers (0x11+4*channel)
*/
#define MID_TX_RDPTR(c) (0x11+4*(c))
#define MID_READ_PTR 0x00007FFF /* next word for PHY */
/*
* Transmit DescrStart Registers (0x12+4*channel)
*/
#define MID_TX_DESCRSTART(c) (0x12+4*(c))
#define MID_DESCR_START 0x00007FFF /* seg buffer being DMAed */
#define ENI155_MAGIC 0xa54b872d
struct midway_eprom {
unsigned char mac[MAC_LEN],inv_mac[MAC_LEN];
unsigned char pad[36];
u32 serial,inv_serial;
u32 magic,inv_magic;
};
/*
* VCI table entry
*/
#define MID_VCI_IN_SERVICE 0x00000001 /* set if VCI is currently in
service list */
#define MID_VCI_SIZE 0x00038000 /* reassembly buffer size,
2*<size> kB */
#define MID_VCI_SIZE_SHIFT 15
#define MID_VCI_LOCATION 0x1ffc0000 /* buffer location */
#define MID_VCI_LOCATION_SHIFT 18
#define MID_VCI_PTI_MODE 0x20000000 /* 0: trash, 1: preserve */
#define MID_VCI_MODE 0xc0000000
#define MID_VCI_MODE_SHIFT 30
#define MID_VCI_READ 0x00007fff
#define MID_VCI_READ_SHIFT 0
#define MID_VCI_DESCR 0x7fff0000
#define MID_VCI_DESCR_SHIFT 16
#define MID_VCI_COUNT 0x000007ff
#define MID_VCI_COUNT_SHIFT 0
#define MID_VCI_STATE 0x0000c000
#define MID_VCI_STATE_SHIFT 14
#define MID_VCI_WRITE 0x7fff0000
#define MID_VCI_WRITE_SHIFT 16
#define MID_MODE_TRASH 0
#define MID_MODE_RAW 1
#define MID_MODE_AAL5 2
/*
* Reassembly buffer descriptor
*/
#define MID_RED_COUNT 0x000007ff
#define MID_RED_CRC_ERR 0x00000800
#define MID_RED_T 0x00001000
#define MID_RED_CE 0x00010000
#define MID_RED_CLP 0x01000000
#define MID_RED_IDEN 0xfe000000
#define MID_RED_SHIFT 25
#define MID_RED_RX_ID 0x1b /* constant identifier */
/*
* Segmentation buffer descriptor
*/
#define MID_SEG_COUNT MID_RED_COUNT
#define MID_SEG_RATE 0x01f80000
#define MID_SEG_RATE_SHIFT 19
#define MID_SEG_PR 0x06000000
#define MID_SEG_PR_SHIFT 25
#define MID_SEG_AAL5 0x08000000
#define MID_SEG_ID 0xf0000000
#define MID_SEG_ID_SHIFT 28
#define MID_SEG_MAX_RATE 63
#define MID_SEG_CLP 0x00000001
#define MID_SEG_PTI 0x0000000e
#define MID_SEG_PTI_SHIFT 1
#define MID_SEG_VCI 0x00003ff0
#define MID_SEG_VCI_SHIFT 4
#define MID_SEG_TX_ID 0xb /* constant identifier */
/*
* DMA entry
*/
#define MID_DMA_COUNT 0xffff0000
#define MID_DMA_COUNT_SHIFT 16
#define MID_DMA_END 0x00000020
#define MID_DMA_TYPE 0x0000000f
#define MID_DT_JK 0x3
#define MID_DT_WORD 0x0
#define MID_DT_2W 0x7
#define MID_DT_4W 0x4
#define MID_DT_8W 0x5
#define MID_DT_16W 0x6
#define MID_DT_2WM 0xf
#define MID_DT_4WM 0xc
#define MID_DT_8WM 0xd
#define MID_DT_16WM 0xe
/* only for RX*/
#define MID_DMA_VCI 0x0000ffc0
#define MID_DMA_VCI_SHIFT 6
/* only for TX */
#define MID_DMA_CHAN 0x000001c0
#define MID_DMA_CHAN_SHIFT 6
#define MID_DT_BYTE 0x1
#define MID_DT_HWORD 0x2
#endif