647 lines
15 KiB
C
647 lines
15 KiB
C
// SPDX-License-Identifier: GPL-2.0-only
|
|
/*
|
|
* ADMV1013 driver
|
|
*
|
|
* Copyright 2021 Analog Devices Inc.
|
|
*/
|
|
|
|
#include <linux/bitfield.h>
|
|
#include <linux/bits.h>
|
|
#include <linux/clk.h>
|
|
#include <linux/device.h>
|
|
#include <linux/iio/iio.h>
|
|
#include <linux/module.h>
|
|
#include <linux/mod_devicetable.h>
|
|
#include <linux/notifier.h>
|
|
#include <linux/property.h>
|
|
#include <linux/regulator/consumer.h>
|
|
#include <linux/spi/spi.h>
|
|
#include <linux/units.h>
|
|
|
|
#include <asm/unaligned.h>
|
|
|
|
/* ADMV1013 Register Map */
|
|
#define ADMV1013_REG_SPI_CONTROL 0x00
|
|
#define ADMV1013_REG_ALARM 0x01
|
|
#define ADMV1013_REG_ALARM_MASKS 0x02
|
|
#define ADMV1013_REG_ENABLE 0x03
|
|
#define ADMV1013_REG_LO_AMP_I 0x05
|
|
#define ADMV1013_REG_LO_AMP_Q 0x06
|
|
#define ADMV1013_REG_OFFSET_ADJUST_I 0x07
|
|
#define ADMV1013_REG_OFFSET_ADJUST_Q 0x08
|
|
#define ADMV1013_REG_QUAD 0x09
|
|
#define ADMV1013_REG_VVA_TEMP_COMP 0x0A
|
|
|
|
/* ADMV1013_REG_SPI_CONTROL Map */
|
|
#define ADMV1013_PARITY_EN_MSK BIT(15)
|
|
#define ADMV1013_SPI_SOFT_RESET_MSK BIT(14)
|
|
#define ADMV1013_CHIP_ID_MSK GENMASK(11, 4)
|
|
#define ADMV1013_CHIP_ID 0xA
|
|
#define ADMV1013_REVISION_ID_MSK GENMASK(3, 0)
|
|
|
|
/* ADMV1013_REG_ALARM Map */
|
|
#define ADMV1013_PARITY_ERROR_MSK BIT(15)
|
|
#define ADMV1013_TOO_FEW_ERRORS_MSK BIT(14)
|
|
#define ADMV1013_TOO_MANY_ERRORS_MSK BIT(13)
|
|
#define ADMV1013_ADDRESS_RANGE_ERROR_MSK BIT(12)
|
|
|
|
/* ADMV1013_REG_ENABLE Map */
|
|
#define ADMV1013_VGA_PD_MSK BIT(15)
|
|
#define ADMV1013_MIXER_PD_MSK BIT(14)
|
|
#define ADMV1013_QUAD_PD_MSK GENMASK(13, 11)
|
|
#define ADMV1013_BG_PD_MSK BIT(10)
|
|
#define ADMV1013_MIXER_IF_EN_MSK BIT(7)
|
|
#define ADMV1013_DET_EN_MSK BIT(5)
|
|
|
|
/* ADMV1013_REG_LO_AMP Map */
|
|
#define ADMV1013_LOAMP_PH_ADJ_FINE_MSK GENMASK(13, 7)
|
|
#define ADMV1013_MIXER_VGATE_MSK GENMASK(6, 0)
|
|
|
|
/* ADMV1013_REG_OFFSET_ADJUST Map */
|
|
#define ADMV1013_MIXER_OFF_ADJ_P_MSK GENMASK(15, 9)
|
|
#define ADMV1013_MIXER_OFF_ADJ_N_MSK GENMASK(8, 2)
|
|
|
|
/* ADMV1013_REG_QUAD Map */
|
|
#define ADMV1013_QUAD_SE_MODE_MSK GENMASK(9, 6)
|
|
#define ADMV1013_QUAD_FILTERS_MSK GENMASK(3, 0)
|
|
|
|
/* ADMV1013_REG_VVA_TEMP_COMP Map */
|
|
#define ADMV1013_VVA_TEMP_COMP_MSK GENMASK(15, 0)
|
|
|
|
/* ADMV1013 Miscellaneous Defines */
|
|
#define ADMV1013_READ BIT(7)
|
|
#define ADMV1013_REG_ADDR_READ_MSK GENMASK(6, 1)
|
|
#define ADMV1013_REG_ADDR_WRITE_MSK GENMASK(22, 17)
|
|
#define ADMV1013_REG_DATA_MSK GENMASK(16, 1)
|
|
|
|
enum {
|
|
ADMV1013_IQ_MODE,
|
|
ADMV1013_IF_MODE
|
|
};
|
|
|
|
enum {
|
|
ADMV1013_RFMOD_I_CALIBPHASE,
|
|
ADMV1013_RFMOD_Q_CALIBPHASE,
|
|
};
|
|
|
|
enum {
|
|
ADMV1013_SE_MODE_POS = 6,
|
|
ADMV1013_SE_MODE_NEG = 9,
|
|
ADMV1013_SE_MODE_DIFF = 12
|
|
};
|
|
|
|
struct admv1013_state {
|
|
struct spi_device *spi;
|
|
struct clk *clkin;
|
|
/* Protect against concurrent accesses to the device and to data */
|
|
struct mutex lock;
|
|
struct regulator *reg;
|
|
struct notifier_block nb;
|
|
unsigned int input_mode;
|
|
unsigned int quad_se_mode;
|
|
bool det_en;
|
|
u8 data[3] __aligned(IIO_DMA_MINALIGN);
|
|
};
|
|
|
|
static int __admv1013_spi_read(struct admv1013_state *st, unsigned int reg,
|
|
unsigned int *val)
|
|
{
|
|
int ret;
|
|
struct spi_transfer t = {0};
|
|
|
|
st->data[0] = ADMV1013_READ | FIELD_PREP(ADMV1013_REG_ADDR_READ_MSK, reg);
|
|
st->data[1] = 0x0;
|
|
st->data[2] = 0x0;
|
|
|
|
t.rx_buf = &st->data[0];
|
|
t.tx_buf = &st->data[0];
|
|
t.len = 3;
|
|
|
|
ret = spi_sync_transfer(st->spi, &t, 1);
|
|
if (ret)
|
|
return ret;
|
|
|
|
*val = FIELD_GET(ADMV1013_REG_DATA_MSK, get_unaligned_be24(&st->data[0]));
|
|
|
|
return ret;
|
|
}
|
|
|
|
static int admv1013_spi_read(struct admv1013_state *st, unsigned int reg,
|
|
unsigned int *val)
|
|
{
|
|
int ret;
|
|
|
|
mutex_lock(&st->lock);
|
|
ret = __admv1013_spi_read(st, reg, val);
|
|
mutex_unlock(&st->lock);
|
|
|
|
return ret;
|
|
}
|
|
|
|
static int __admv1013_spi_write(struct admv1013_state *st,
|
|
unsigned int reg,
|
|
unsigned int val)
|
|
{
|
|
put_unaligned_be24(FIELD_PREP(ADMV1013_REG_DATA_MSK, val) |
|
|
FIELD_PREP(ADMV1013_REG_ADDR_WRITE_MSK, reg), &st->data[0]);
|
|
|
|
return spi_write(st->spi, &st->data[0], 3);
|
|
}
|
|
|
|
static int admv1013_spi_write(struct admv1013_state *st, unsigned int reg,
|
|
unsigned int val)
|
|
{
|
|
int ret;
|
|
|
|
mutex_lock(&st->lock);
|
|
ret = __admv1013_spi_write(st, reg, val);
|
|
mutex_unlock(&st->lock);
|
|
|
|
return ret;
|
|
}
|
|
|
|
static int __admv1013_spi_update_bits(struct admv1013_state *st, unsigned int reg,
|
|
unsigned int mask, unsigned int val)
|
|
{
|
|
int ret;
|
|
unsigned int data, temp;
|
|
|
|
ret = __admv1013_spi_read(st, reg, &data);
|
|
if (ret)
|
|
return ret;
|
|
|
|
temp = (data & ~mask) | (val & mask);
|
|
|
|
return __admv1013_spi_write(st, reg, temp);
|
|
}
|
|
|
|
static int admv1013_spi_update_bits(struct admv1013_state *st, unsigned int reg,
|
|
unsigned int mask, unsigned int val)
|
|
{
|
|
int ret;
|
|
|
|
mutex_lock(&st->lock);
|
|
ret = __admv1013_spi_update_bits(st, reg, mask, val);
|
|
mutex_unlock(&st->lock);
|
|
|
|
return ret;
|
|
}
|
|
|
|
static int admv1013_read_raw(struct iio_dev *indio_dev,
|
|
struct iio_chan_spec const *chan,
|
|
int *val, int *val2, long info)
|
|
{
|
|
struct admv1013_state *st = iio_priv(indio_dev);
|
|
unsigned int data, addr;
|
|
int ret;
|
|
|
|
switch (info) {
|
|
case IIO_CHAN_INFO_CALIBBIAS:
|
|
switch (chan->channel) {
|
|
case IIO_MOD_I:
|
|
addr = ADMV1013_REG_OFFSET_ADJUST_I;
|
|
break;
|
|
case IIO_MOD_Q:
|
|
addr = ADMV1013_REG_OFFSET_ADJUST_Q;
|
|
break;
|
|
default:
|
|
return -EINVAL;
|
|
}
|
|
|
|
ret = admv1013_spi_read(st, addr, &data);
|
|
if (ret)
|
|
return ret;
|
|
|
|
if (!chan->channel)
|
|
*val = FIELD_GET(ADMV1013_MIXER_OFF_ADJ_P_MSK, data);
|
|
else
|
|
*val = FIELD_GET(ADMV1013_MIXER_OFF_ADJ_N_MSK, data);
|
|
|
|
return IIO_VAL_INT;
|
|
default:
|
|
return -EINVAL;
|
|
}
|
|
}
|
|
|
|
static int admv1013_write_raw(struct iio_dev *indio_dev,
|
|
struct iio_chan_spec const *chan,
|
|
int val, int val2, long info)
|
|
{
|
|
struct admv1013_state *st = iio_priv(indio_dev);
|
|
unsigned int addr, data, msk;
|
|
|
|
switch (info) {
|
|
case IIO_CHAN_INFO_CALIBBIAS:
|
|
switch (chan->channel2) {
|
|
case IIO_MOD_I:
|
|
addr = ADMV1013_REG_OFFSET_ADJUST_I;
|
|
break;
|
|
case IIO_MOD_Q:
|
|
addr = ADMV1013_REG_OFFSET_ADJUST_Q;
|
|
break;
|
|
default:
|
|
return -EINVAL;
|
|
}
|
|
|
|
if (!chan->channel) {
|
|
msk = ADMV1013_MIXER_OFF_ADJ_P_MSK;
|
|
data = FIELD_PREP(ADMV1013_MIXER_OFF_ADJ_P_MSK, val);
|
|
} else {
|
|
msk = ADMV1013_MIXER_OFF_ADJ_N_MSK;
|
|
data = FIELD_PREP(ADMV1013_MIXER_OFF_ADJ_N_MSK, val);
|
|
}
|
|
|
|
return admv1013_spi_update_bits(st, addr, msk, data);
|
|
default:
|
|
return -EINVAL;
|
|
}
|
|
}
|
|
|
|
static ssize_t admv1013_read(struct iio_dev *indio_dev,
|
|
uintptr_t private,
|
|
const struct iio_chan_spec *chan,
|
|
char *buf)
|
|
{
|
|
struct admv1013_state *st = iio_priv(indio_dev);
|
|
unsigned int data, addr;
|
|
int ret;
|
|
|
|
switch ((u32)private) {
|
|
case ADMV1013_RFMOD_I_CALIBPHASE:
|
|
addr = ADMV1013_REG_LO_AMP_I;
|
|
break;
|
|
case ADMV1013_RFMOD_Q_CALIBPHASE:
|
|
addr = ADMV1013_REG_LO_AMP_Q;
|
|
break;
|
|
default:
|
|
return -EINVAL;
|
|
}
|
|
|
|
ret = admv1013_spi_read(st, addr, &data);
|
|
if (ret)
|
|
return ret;
|
|
|
|
data = FIELD_GET(ADMV1013_LOAMP_PH_ADJ_FINE_MSK, data);
|
|
|
|
return sysfs_emit(buf, "%u\n", data);
|
|
}
|
|
|
|
static ssize_t admv1013_write(struct iio_dev *indio_dev,
|
|
uintptr_t private,
|
|
const struct iio_chan_spec *chan,
|
|
const char *buf, size_t len)
|
|
{
|
|
struct admv1013_state *st = iio_priv(indio_dev);
|
|
unsigned int data;
|
|
int ret;
|
|
|
|
ret = kstrtou32(buf, 10, &data);
|
|
if (ret)
|
|
return ret;
|
|
|
|
data = FIELD_PREP(ADMV1013_LOAMP_PH_ADJ_FINE_MSK, data);
|
|
|
|
switch ((u32)private) {
|
|
case ADMV1013_RFMOD_I_CALIBPHASE:
|
|
ret = admv1013_spi_update_bits(st, ADMV1013_REG_LO_AMP_I,
|
|
ADMV1013_LOAMP_PH_ADJ_FINE_MSK,
|
|
data);
|
|
if (ret)
|
|
return ret;
|
|
break;
|
|
case ADMV1013_RFMOD_Q_CALIBPHASE:
|
|
ret = admv1013_spi_update_bits(st, ADMV1013_REG_LO_AMP_Q,
|
|
ADMV1013_LOAMP_PH_ADJ_FINE_MSK,
|
|
data);
|
|
if (ret)
|
|
return ret;
|
|
break;
|
|
default:
|
|
return -EINVAL;
|
|
}
|
|
|
|
return ret ? ret : len;
|
|
}
|
|
|
|
static int admv1013_update_quad_filters(struct admv1013_state *st)
|
|
{
|
|
unsigned int filt_raw;
|
|
u64 rate = clk_get_rate(st->clkin);
|
|
|
|
if (rate >= (5400 * HZ_PER_MHZ) && rate <= (7000 * HZ_PER_MHZ))
|
|
filt_raw = 15;
|
|
else if (rate >= (5400 * HZ_PER_MHZ) && rate <= (8000 * HZ_PER_MHZ))
|
|
filt_raw = 10;
|
|
else if (rate >= (6600 * HZ_PER_MHZ) && rate <= (9200 * HZ_PER_MHZ))
|
|
filt_raw = 5;
|
|
else
|
|
filt_raw = 0;
|
|
|
|
return __admv1013_spi_update_bits(st, ADMV1013_REG_QUAD,
|
|
ADMV1013_QUAD_FILTERS_MSK,
|
|
FIELD_PREP(ADMV1013_QUAD_FILTERS_MSK, filt_raw));
|
|
}
|
|
|
|
static int admv1013_update_mixer_vgate(struct admv1013_state *st)
|
|
{
|
|
unsigned int mixer_vgate;
|
|
int vcm;
|
|
|
|
vcm = regulator_get_voltage(st->reg);
|
|
if (vcm < 0)
|
|
return vcm;
|
|
|
|
if (vcm < 1800000)
|
|
mixer_vgate = (2389 * vcm / 1000000 + 8100) / 100;
|
|
else if (vcm > 1800000 && vcm < 2600000)
|
|
mixer_vgate = (2375 * vcm / 1000000 + 125) / 100;
|
|
else
|
|
return -EINVAL;
|
|
|
|
return __admv1013_spi_update_bits(st, ADMV1013_REG_LO_AMP_I,
|
|
ADMV1013_MIXER_VGATE_MSK,
|
|
FIELD_PREP(ADMV1013_MIXER_VGATE_MSK, mixer_vgate));
|
|
}
|
|
|
|
static int admv1013_reg_access(struct iio_dev *indio_dev,
|
|
unsigned int reg,
|
|
unsigned int write_val,
|
|
unsigned int *read_val)
|
|
{
|
|
struct admv1013_state *st = iio_priv(indio_dev);
|
|
|
|
if (read_val)
|
|
return admv1013_spi_read(st, reg, read_val);
|
|
else
|
|
return admv1013_spi_write(st, reg, write_val);
|
|
}
|
|
|
|
static const struct iio_info admv1013_info = {
|
|
.read_raw = admv1013_read_raw,
|
|
.write_raw = admv1013_write_raw,
|
|
.debugfs_reg_access = &admv1013_reg_access,
|
|
};
|
|
|
|
static int admv1013_freq_change(struct notifier_block *nb, unsigned long action, void *data)
|
|
{
|
|
struct admv1013_state *st = container_of(nb, struct admv1013_state, nb);
|
|
int ret;
|
|
|
|
if (action == POST_RATE_CHANGE) {
|
|
mutex_lock(&st->lock);
|
|
ret = notifier_from_errno(admv1013_update_quad_filters(st));
|
|
mutex_unlock(&st->lock);
|
|
return ret;
|
|
}
|
|
|
|
return NOTIFY_OK;
|
|
}
|
|
|
|
#define _ADMV1013_EXT_INFO(_name, _shared, _ident) { \
|
|
.name = _name, \
|
|
.read = admv1013_read, \
|
|
.write = admv1013_write, \
|
|
.private = _ident, \
|
|
.shared = _shared, \
|
|
}
|
|
|
|
static const struct iio_chan_spec_ext_info admv1013_ext_info[] = {
|
|
_ADMV1013_EXT_INFO("i_calibphase", IIO_SEPARATE, ADMV1013_RFMOD_I_CALIBPHASE),
|
|
_ADMV1013_EXT_INFO("q_calibphase", IIO_SEPARATE, ADMV1013_RFMOD_Q_CALIBPHASE),
|
|
{ },
|
|
};
|
|
|
|
#define ADMV1013_CHAN_PHASE(_channel, _channel2, _admv1013_ext_info) { \
|
|
.type = IIO_ALTVOLTAGE, \
|
|
.output = 0, \
|
|
.indexed = 1, \
|
|
.channel2 = _channel2, \
|
|
.channel = _channel, \
|
|
.differential = 1, \
|
|
.ext_info = _admv1013_ext_info, \
|
|
}
|
|
|
|
#define ADMV1013_CHAN_CALIB(_channel, rf_comp) { \
|
|
.type = IIO_ALTVOLTAGE, \
|
|
.output = 0, \
|
|
.indexed = 1, \
|
|
.channel = _channel, \
|
|
.channel2 = IIO_MOD_##rf_comp, \
|
|
.info_mask_separate = BIT(IIO_CHAN_INFO_CALIBBIAS), \
|
|
}
|
|
|
|
static const struct iio_chan_spec admv1013_channels[] = {
|
|
ADMV1013_CHAN_PHASE(0, 1, admv1013_ext_info),
|
|
ADMV1013_CHAN_CALIB(0, I),
|
|
ADMV1013_CHAN_CALIB(0, Q),
|
|
ADMV1013_CHAN_CALIB(1, I),
|
|
ADMV1013_CHAN_CALIB(1, Q),
|
|
};
|
|
|
|
static int admv1013_init(struct admv1013_state *st)
|
|
{
|
|
int ret;
|
|
unsigned int data;
|
|
struct spi_device *spi = st->spi;
|
|
|
|
/* Perform a software reset */
|
|
ret = __admv1013_spi_update_bits(st, ADMV1013_REG_SPI_CONTROL,
|
|
ADMV1013_SPI_SOFT_RESET_MSK,
|
|
FIELD_PREP(ADMV1013_SPI_SOFT_RESET_MSK, 1));
|
|
if (ret)
|
|
return ret;
|
|
|
|
ret = __admv1013_spi_update_bits(st, ADMV1013_REG_SPI_CONTROL,
|
|
ADMV1013_SPI_SOFT_RESET_MSK,
|
|
FIELD_PREP(ADMV1013_SPI_SOFT_RESET_MSK, 0));
|
|
if (ret)
|
|
return ret;
|
|
|
|
ret = __admv1013_spi_read(st, ADMV1013_REG_SPI_CONTROL, &data);
|
|
if (ret)
|
|
return ret;
|
|
|
|
data = FIELD_GET(ADMV1013_CHIP_ID_MSK, data);
|
|
if (data != ADMV1013_CHIP_ID) {
|
|
dev_err(&spi->dev, "Invalid Chip ID.\n");
|
|
return -EINVAL;
|
|
}
|
|
|
|
ret = __admv1013_spi_write(st, ADMV1013_REG_VVA_TEMP_COMP, 0xE700);
|
|
if (ret)
|
|
return ret;
|
|
|
|
data = FIELD_PREP(ADMV1013_QUAD_SE_MODE_MSK, st->quad_se_mode);
|
|
|
|
ret = __admv1013_spi_update_bits(st, ADMV1013_REG_QUAD,
|
|
ADMV1013_QUAD_SE_MODE_MSK, data);
|
|
if (ret)
|
|
return ret;
|
|
|
|
ret = admv1013_update_mixer_vgate(st);
|
|
if (ret)
|
|
return ret;
|
|
|
|
ret = admv1013_update_quad_filters(st);
|
|
if (ret)
|
|
return ret;
|
|
|
|
return __admv1013_spi_update_bits(st, ADMV1013_REG_ENABLE,
|
|
ADMV1013_DET_EN_MSK |
|
|
ADMV1013_MIXER_IF_EN_MSK,
|
|
st->det_en |
|
|
st->input_mode);
|
|
}
|
|
|
|
static void admv1013_reg_disable(void *data)
|
|
{
|
|
regulator_disable(data);
|
|
}
|
|
|
|
static void admv1013_powerdown(void *data)
|
|
{
|
|
unsigned int enable_reg, enable_reg_msk;
|
|
|
|
/* Disable all components in the Enable Register */
|
|
enable_reg_msk = ADMV1013_VGA_PD_MSK |
|
|
ADMV1013_MIXER_PD_MSK |
|
|
ADMV1013_QUAD_PD_MSK |
|
|
ADMV1013_BG_PD_MSK |
|
|
ADMV1013_MIXER_IF_EN_MSK |
|
|
ADMV1013_DET_EN_MSK;
|
|
|
|
enable_reg = FIELD_PREP(ADMV1013_VGA_PD_MSK, 1) |
|
|
FIELD_PREP(ADMV1013_MIXER_PD_MSK, 1) |
|
|
FIELD_PREP(ADMV1013_QUAD_PD_MSK, 7) |
|
|
FIELD_PREP(ADMV1013_BG_PD_MSK, 1) |
|
|
FIELD_PREP(ADMV1013_MIXER_IF_EN_MSK, 0) |
|
|
FIELD_PREP(ADMV1013_DET_EN_MSK, 0);
|
|
|
|
admv1013_spi_update_bits(data, ADMV1013_REG_ENABLE, enable_reg_msk, enable_reg);
|
|
}
|
|
|
|
static int admv1013_properties_parse(struct admv1013_state *st)
|
|
{
|
|
int ret;
|
|
const char *str;
|
|
struct spi_device *spi = st->spi;
|
|
|
|
st->det_en = device_property_read_bool(&spi->dev, "adi,detector-enable");
|
|
|
|
ret = device_property_read_string(&spi->dev, "adi,input-mode", &str);
|
|
if (ret)
|
|
st->input_mode = ADMV1013_IQ_MODE;
|
|
|
|
if (!strcmp(str, "iq"))
|
|
st->input_mode = ADMV1013_IQ_MODE;
|
|
else if (!strcmp(str, "if"))
|
|
st->input_mode = ADMV1013_IF_MODE;
|
|
else
|
|
return -EINVAL;
|
|
|
|
ret = device_property_read_string(&spi->dev, "adi,quad-se-mode", &str);
|
|
if (ret)
|
|
st->quad_se_mode = ADMV1013_SE_MODE_DIFF;
|
|
|
|
if (!strcmp(str, "diff"))
|
|
st->quad_se_mode = ADMV1013_SE_MODE_DIFF;
|
|
else if (!strcmp(str, "se-pos"))
|
|
st->quad_se_mode = ADMV1013_SE_MODE_POS;
|
|
else if (!strcmp(str, "se-neg"))
|
|
st->quad_se_mode = ADMV1013_SE_MODE_NEG;
|
|
else
|
|
return -EINVAL;
|
|
|
|
st->reg = devm_regulator_get(&spi->dev, "vcm");
|
|
if (IS_ERR(st->reg))
|
|
return dev_err_probe(&spi->dev, PTR_ERR(st->reg),
|
|
"failed to get the common-mode voltage\n");
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int admv1013_probe(struct spi_device *spi)
|
|
{
|
|
struct iio_dev *indio_dev;
|
|
struct admv1013_state *st;
|
|
int ret;
|
|
|
|
indio_dev = devm_iio_device_alloc(&spi->dev, sizeof(*st));
|
|
if (!indio_dev)
|
|
return -ENOMEM;
|
|
|
|
st = iio_priv(indio_dev);
|
|
|
|
indio_dev->info = &admv1013_info;
|
|
indio_dev->name = "admv1013";
|
|
indio_dev->channels = admv1013_channels;
|
|
indio_dev->num_channels = ARRAY_SIZE(admv1013_channels);
|
|
|
|
st->spi = spi;
|
|
|
|
ret = admv1013_properties_parse(st);
|
|
if (ret)
|
|
return ret;
|
|
|
|
ret = regulator_enable(st->reg);
|
|
if (ret) {
|
|
dev_err(&spi->dev, "Failed to enable specified Common-Mode Voltage!\n");
|
|
return ret;
|
|
}
|
|
|
|
ret = devm_add_action_or_reset(&spi->dev, admv1013_reg_disable,
|
|
st->reg);
|
|
if (ret)
|
|
return ret;
|
|
|
|
st->clkin = devm_clk_get_enabled(&spi->dev, "lo_in");
|
|
if (IS_ERR(st->clkin))
|
|
return dev_err_probe(&spi->dev, PTR_ERR(st->clkin),
|
|
"failed to get the LO input clock\n");
|
|
|
|
st->nb.notifier_call = admv1013_freq_change;
|
|
ret = devm_clk_notifier_register(&spi->dev, st->clkin, &st->nb);
|
|
if (ret)
|
|
return ret;
|
|
|
|
mutex_init(&st->lock);
|
|
|
|
ret = admv1013_init(st);
|
|
if (ret) {
|
|
dev_err(&spi->dev, "admv1013 init failed\n");
|
|
return ret;
|
|
}
|
|
|
|
ret = devm_add_action_or_reset(&spi->dev, admv1013_powerdown, st);
|
|
if (ret)
|
|
return ret;
|
|
|
|
return devm_iio_device_register(&spi->dev, indio_dev);
|
|
}
|
|
|
|
static const struct spi_device_id admv1013_id[] = {
|
|
{ "admv1013", 0 },
|
|
{}
|
|
};
|
|
MODULE_DEVICE_TABLE(spi, admv1013_id);
|
|
|
|
static const struct of_device_id admv1013_of_match[] = {
|
|
{ .compatible = "adi,admv1013" },
|
|
{},
|
|
};
|
|
MODULE_DEVICE_TABLE(of, admv1013_of_match);
|
|
|
|
static struct spi_driver admv1013_driver = {
|
|
.driver = {
|
|
.name = "admv1013",
|
|
.of_match_table = admv1013_of_match,
|
|
},
|
|
.probe = admv1013_probe,
|
|
.id_table = admv1013_id,
|
|
};
|
|
module_spi_driver(admv1013_driver);
|
|
|
|
MODULE_AUTHOR("Antoniu Miclaus <antoniu.miclaus@analog.com");
|
|
MODULE_DESCRIPTION("Analog Devices ADMV1013");
|
|
MODULE_LICENSE("GPL v2");
|