kvj
/
linux-zen-desktop
1
0
Fork 0
Code Issues Pull Requests Packages Projects Releases Wiki Activity
linux-zen-desktop/drivers/input/touchscreen/edt-ft5x06.c

1523 lines
39 KiB
C
Raw Permalink Blame History

// SPDX-License-Identifier: GPL-2.0
/*
* Copyright (C) 2012 Simon Budig, <simon.budig@kernelconcepts.de>
* Daniel Wagener <daniel.wagener@kernelconcepts.de> (M09 firmware support)
* Lothar Waßmann <LW@KARO-electronics.de> (DT support)
* Dario Binacchi <dario.binacchi@amarulasolutions.com> (regmap support)
*/
/*
* This is a driver for the EDT "Polytouch" family of touch controllers
* based on the FocalTech FT5x06 line of chips.
*
* Development of this driver has been sponsored by Glyn:
* http://www.glyn.com/Products/Displays
*/
#include <linux/debugfs.h>
#include <linux/delay.h>
#include <linux/gpio/consumer.h>
#include <linux/i2c.h>
#include <linux/interrupt.h>
#include <linux/input.h>
#include <linux/input/mt.h>
#include <linux/input/touchscreen.h>
#include <linux/irq.h>
#include <linux/kernel.h>
#include <linux/module.h>
#include <linux/property.h>
#include <linux/ratelimit.h>
#include <linux/regmap.h>
#include <linux/regulator/consumer.h>
#include <linux/slab.h>
#include <linux/uaccess.h>
#include <asm/unaligned.h>
#define WORK_REGISTER_THRESHOLD 0x00
#define WORK_REGISTER_REPORT_RATE 0x08
#define WORK_REGISTER_GAIN 0x30
#define WORK_REGISTER_OFFSET 0x31
#define WORK_REGISTER_NUM_X 0x33
#define WORK_REGISTER_NUM_Y 0x34
#define PMOD_REGISTER_ACTIVE 0x00
#define PMOD_REGISTER_HIBERNATE 0x03
#define M09_REGISTER_THRESHOLD 0x80
#define M09_REGISTER_GAIN 0x92
#define M09_REGISTER_OFFSET 0x93
#define M09_REGISTER_NUM_X 0x94
#define M09_REGISTER_NUM_Y 0x95
#define M12_REGISTER_REPORT_RATE 0x88
#define EV_REGISTER_THRESHOLD 0x40
#define EV_REGISTER_GAIN 0x41
#define EV_REGISTER_OFFSET_Y 0x45
#define EV_REGISTER_OFFSET_X 0x46
#define NO_REGISTER 0xff
#define WORK_REGISTER_OPMODE 0x3c
#define FACTORY_REGISTER_OPMODE 0x01
#define PMOD_REGISTER_OPMODE 0xa5
#define TOUCH_EVENT_DOWN 0x00
#define TOUCH_EVENT_UP 0x01
#define TOUCH_EVENT_ON 0x02
#define TOUCH_EVENT_RESERVED 0x03
#define EDT_NAME_LEN 23
#define EDT_SWITCH_MODE_RETRIES 10
#define EDT_SWITCH_MODE_DELAY 5 /* msec */
#define EDT_RAW_DATA_RETRIES 100
#define EDT_RAW_DATA_DELAY 1000 /* usec */
#define EDT_DEFAULT_NUM_X 1024
#define EDT_DEFAULT_NUM_Y 1024
#define M06_REG_CMD(factory) ((factory) ? 0xf3 : 0xfc)
#define M06_REG_ADDR(factory, addr) ((factory) ? (addr) & 0x7f : (addr) & 0x3f)
enum edt_pmode {
EDT_PMODE_NOT_SUPPORTED,
EDT_PMODE_HIBERNATE,
EDT_PMODE_POWEROFF,
};
enum edt_ver {
EDT_M06,
EDT_M09,
EDT_M12,
EV_FT,
GENERIC_FT,
};
struct edt_reg_addr {
int reg_threshold;
int reg_report_rate;
int reg_gain;
int reg_offset;
int reg_offset_x;
int reg_offset_y;
int reg_num_x;
int reg_num_y;
};
struct edt_ft5x06_ts_data {
struct i2c_client *client;
struct input_dev *input;
struct touchscreen_properties prop;
u16 num_x;
u16 num_y;
struct regulator *vcc;
struct regulator *iovcc;
struct gpio_desc *reset_gpio;
struct gpio_desc *wake_gpio;
struct regmap *regmap;
#if defined(CONFIG_DEBUG_FS)
struct dentry *debug_dir;
u8 *raw_buffer;
size_t raw_bufsize;
#endif
struct mutex mutex;
bool factory_mode;
enum edt_pmode suspend_mode;
int threshold;
int gain;
int offset;
int offset_x;
int offset_y;
int report_rate;
int max_support_points;
int point_len;
u8 tdata_cmd;
int tdata_len;
int tdata_offset;
char name[EDT_NAME_LEN];
char fw_version[EDT_NAME_LEN];
struct edt_reg_addr reg_addr;
enum edt_ver version;
unsigned int crc_errors;
unsigned int header_errors;
};
struct edt_i2c_chip_data {
int max_support_points;
};
static const struct regmap_config edt_ft5x06_i2c_regmap_config = {
.reg_bits = 8,
.val_bits = 8,
};
static bool edt_ft5x06_ts_check_crc(struct edt_ft5x06_ts_data *tsdata,
u8 *buf, int buflen)
{
int i;
u8 crc = 0;
for (i = 0; i < buflen - 1; i++)
crc ^= buf[i];
if (crc != buf[buflen - 1]) {
tsdata->crc_errors++;
dev_err_ratelimited(&tsdata->client->dev,
"crc error: 0x%02x expected, got 0x%02x\n",
crc, buf[buflen - 1]);
return false;
}
return true;
}
static int edt_M06_i2c_read(void *context, const void *reg_buf, size_t reg_size,
void *val_buf, size_t val_size)
{
struct device *dev = context;
struct i2c_client *i2c = to_i2c_client(dev);
struct edt_ft5x06_ts_data *tsdata = i2c_get_clientdata(i2c);
struct i2c_msg xfer[2];
bool reg_read = false;
u8 addr;
u8 wlen;
u8 wbuf[4], rbuf[3];
int ret;
addr = *((u8 *)reg_buf);
wbuf[0] = addr;
switch (addr) {
case 0xf5:
wlen = 3;
wbuf[0] = 0xf5;
wbuf[1] = 0xe;
wbuf[2] = *((u8 *)val_buf);
break;
case 0xf9:
wlen = 1;
break;
default:
wlen = 2;
reg_read = true;
wbuf[0] = M06_REG_CMD(tsdata->factory_mode);
wbuf[1] = M06_REG_ADDR(tsdata->factory_mode, addr);
wbuf[1] |= tsdata->factory_mode ? 0x80 : 0x40;
}
xfer[0].addr = i2c->addr;
xfer[0].flags = 0;
xfer[0].len = wlen;
xfer[0].buf = wbuf;
xfer[1].addr = i2c->addr;
xfer[1].flags = I2C_M_RD;
xfer[1].len = reg_read ? 2 : val_size;
xfer[1].buf = reg_read ? rbuf : val_buf;
ret = i2c_transfer(i2c->adapter, xfer, 2);
if (ret != 2) {
if (ret < 0)
return ret;
return -EIO;
}
if (addr == 0xf9) {
u8 *buf = (u8 *)val_buf;
if (buf[0] != 0xaa || buf[1] != 0xaa ||
buf[2] != val_size) {
tsdata->header_errors++;
dev_err_ratelimited(dev,
"Unexpected header: %02x%02x%02x\n",
buf[0], buf[1], buf[2]);
return -EIO;
}
if (!edt_ft5x06_ts_check_crc(tsdata, val_buf, val_size))
return -EIO;
} else if (reg_read) {
wbuf[2] = rbuf[0];
wbuf[3] = rbuf[1];
if (!edt_ft5x06_ts_check_crc(tsdata, wbuf, 4))
return -EIO;
*((u8 *)val_buf) = rbuf[0];
}
return 0;
}
static int edt_M06_i2c_write(void *context, const void *data, size_t count)
{
struct device *dev = context;
struct i2c_client *i2c = to_i2c_client(dev);
struct edt_ft5x06_ts_data *tsdata = i2c_get_clientdata(i2c);
u8 addr, val;
u8 wbuf[4];
struct i2c_msg xfer;
int ret;
addr = *((u8 *)data);
val = *((u8 *)data + 1);
wbuf[0] = M06_REG_CMD(tsdata->factory_mode);
wbuf[1] = M06_REG_ADDR(tsdata->factory_mode, addr);
wbuf[2] = val;
wbuf[3] = wbuf[0] ^ wbuf[1] ^ wbuf[2];
xfer.addr = i2c->addr;
xfer.flags = 0;
xfer.len = 4;
xfer.buf = wbuf;
ret = i2c_transfer(i2c->adapter, &xfer, 1);
if (ret != 1) {
if (ret < 0)
return ret;
return -EIO;
}
return 0;
}
static const struct regmap_config edt_M06_i2c_regmap_config = {
.reg_bits = 8,
.val_bits = 8,
.read = edt_M06_i2c_read,
.write = edt_M06_i2c_write,
};
static irqreturn_t edt_ft5x06_ts_isr(int irq, void *dev_id)
{
struct edt_ft5x06_ts_data *tsdata = dev_id;
struct device *dev = &tsdata->client->dev;
u8 rdbuf[63];
int i, type, x, y, id;
int error;
memset(rdbuf, 0, sizeof(rdbuf));
error = regmap_bulk_read(tsdata->regmap, tsdata->tdata_cmd, rdbuf,
tsdata->tdata_len);
if (error) {
dev_err_ratelimited(dev, "Unable to fetch data, error: %d\n",
error);
goto out;
}
for (i = 0; i < tsdata->max_support_points; i++) {
u8 *buf = &rdbuf[i * tsdata->point_len + tsdata->tdata_offset];
type = buf[0] >> 6;
/* ignore Reserved events */
if (type == TOUCH_EVENT_RESERVED)
continue;
/* M06 sometimes sends bogus coordinates in TOUCH_DOWN */
if (tsdata->version == EDT_M06 && type == TOUCH_EVENT_DOWN)
continue;
x = get_unaligned_be16(buf) & 0x0fff;
y = get_unaligned_be16(buf + 2) & 0x0fff;
/* The FT5x26 send the y coordinate first */
if (tsdata->version == EV_FT)
swap(x, y);
id = (buf[2] >> 4) & 0x0f;
input_mt_slot(tsdata->input, id);
if (input_mt_report_slot_state(tsdata->input, MT_TOOL_FINGER,
type != TOUCH_EVENT_UP))
touchscreen_report_pos(tsdata->input, &tsdata->prop,
x, y, true);
}
input_mt_report_pointer_emulation(tsdata->input, true);
input_sync(tsdata->input);
out:
return IRQ_HANDLED;
}
struct edt_ft5x06_attribute {
struct device_attribute dattr;
size_t field_offset;
u8 limit_low;
u8 limit_high;
u8 addr_m06;
u8 addr_m09;
u8 addr_ev;
};
#define EDT_ATTR(_field, _mode, _addr_m06, _addr_m09, _addr_ev, \
_limit_low, _limit_high) \
struct edt_ft5x06_attribute edt_ft5x06_attr_##_field = { \
.dattr = __ATTR(_field, _mode, \
edt_ft5x06_setting_show, \
edt_ft5x06_setting_store), \
.field_offset = offsetof(struct edt_ft5x06_ts_data, _field), \
.addr_m06 = _addr_m06, \
.addr_m09 = _addr_m09, \
.addr_ev = _addr_ev, \
.limit_low = _limit_low, \
.limit_high = _limit_high, \
}
static ssize_t edt_ft5x06_setting_show(struct device *dev,
struct device_attribute *dattr,
char *buf)
{
struct i2c_client *client = to_i2c_client(dev);
struct edt_ft5x06_ts_data *tsdata = i2c_get_clientdata(client);
struct edt_ft5x06_attribute *attr =
container_of(dattr, struct edt_ft5x06_attribute, dattr);
u8 *field = (u8 *)tsdata + attr->field_offset;
unsigned int val;
size_t count = 0;
int error = 0;
u8 addr;
mutex_lock(&tsdata->mutex);
if (tsdata->factory_mode) {
error = -EIO;
goto out;
}
switch (tsdata->version) {
case EDT_M06:
addr = attr->addr_m06;
break;
case EDT_M09:
case EDT_M12:
case GENERIC_FT:
addr = attr->addr_m09;
break;
case EV_FT:
addr = attr->addr_ev;
break;
default:
error = -ENODEV;
goto out;
}
if (addr != NO_REGISTER) {
error = regmap_read(tsdata->regmap, addr, &val);
if (error) {
dev_err(&tsdata->client->dev,
"Failed to fetch attribute %s, error %d\n",
dattr->attr.name, error);
goto out;
}
} else {
val = *field;
}
if (val != *field) {
dev_warn(&tsdata->client->dev,
"%s: read (%d) and stored value (%d) differ\n",
dattr->attr.name, val, *field);
*field = val;
}
count = scnprintf(buf, PAGE_SIZE, "%d\n", val);
out:
mutex_unlock(&tsdata->mutex);
return error ?: count;
}
static ssize_t edt_ft5x06_setting_store(struct device *dev,
struct device_attribute *dattr,
const char *buf, size_t count)
{
struct i2c_client *client = to_i2c_client(dev);
struct edt_ft5x06_ts_data *tsdata = i2c_get_clientdata(client);
struct edt_ft5x06_attribute *attr =
container_of(dattr, struct edt_ft5x06_attribute, dattr);
u8 *field = (u8 *)tsdata + attr->field_offset;
unsigned int val;
int error;
u8 addr;
mutex_lock(&tsdata->mutex);
if (tsdata->factory_mode) {
error = -EIO;
goto out;
}
error = kstrtouint(buf, 0, &val);
if (error)
goto out;
if (val < attr->limit_low || val > attr->limit_high) {
error = -ERANGE;
goto out;
}
switch (tsdata->version) {
case EDT_M06:
addr = attr->addr_m06;
break;
case EDT_M09:
case EDT_M12:
case GENERIC_FT:
addr = attr->addr_m09;
break;
case EV_FT:
addr = attr->addr_ev;
break;
default:
error = -ENODEV;
goto out;
}
if (addr != NO_REGISTER) {
error = regmap_write(tsdata->regmap, addr, val);
if (error) {
dev_err(&tsdata->client->dev,
"Failed to update attribute %s, error: %d\n",
dattr->attr.name, error);
goto out;
}
}
*field = val;
out:
mutex_unlock(&tsdata->mutex);
return error ?: count;
}
/* m06, m09: range 0-31, m12: range 0-5 */
static EDT_ATTR(gain, S_IWUSR | S_IRUGO, WORK_REGISTER_GAIN,
M09_REGISTER_GAIN, EV_REGISTER_GAIN, 0, 31);
/* m06, m09: range 0-31, m12: range 0-16 */
static EDT_ATTR(offset, S_IWUSR | S_IRUGO, WORK_REGISTER_OFFSET,
M09_REGISTER_OFFSET, NO_REGISTER, 0, 31);
/* m06, m09, m12: no supported, ev_ft: range 0-80 */
static EDT_ATTR(offset_x, S_IWUSR | S_IRUGO, NO_REGISTER, NO_REGISTER,
EV_REGISTER_OFFSET_X, 0, 80);
/* m06, m09, m12: no supported, ev_ft: range 0-80 */
static EDT_ATTR(offset_y, S_IWUSR | S_IRUGO, NO_REGISTER, NO_REGISTER,
EV_REGISTER_OFFSET_Y, 0, 80);
/* m06: range 20 to 80, m09: range 0 to 30, m12: range 1 to 255... */
static EDT_ATTR(threshold, S_IWUSR | S_IRUGO, WORK_REGISTER_THRESHOLD,
M09_REGISTER_THRESHOLD, EV_REGISTER_THRESHOLD, 0, 255);
/* m06: range 3 to 14, m12: range 1 to 255 */
static EDT_ATTR(report_rate, S_IWUSR | S_IRUGO, WORK_REGISTER_REPORT_RATE,
M12_REGISTER_REPORT_RATE, NO_REGISTER, 0, 255);
static ssize_t model_show(struct device *dev, struct device_attribute *attr,
char *buf)
{
struct i2c_client *client = to_i2c_client(dev);
struct edt_ft5x06_ts_data *tsdata = i2c_get_clientdata(client);
return sysfs_emit(buf, "%s\n", tsdata->name);
}
static DEVICE_ATTR_RO(model);
static ssize_t fw_version_show(struct device *dev,
struct device_attribute *attr, char *buf)
{
struct i2c_client *client = to_i2c_client(dev);
struct edt_ft5x06_ts_data *tsdata = i2c_get_clientdata(client);
return sysfs_emit(buf, "%s\n", tsdata->fw_version);
}
static DEVICE_ATTR_RO(fw_version);
/* m06 only */
static ssize_t header_errors_show(struct device *dev,
struct device_attribute *attr, char *buf)
{
struct i2c_client *client = to_i2c_client(dev);
struct edt_ft5x06_ts_data *tsdata = i2c_get_clientdata(client);
return sysfs_emit(buf, "%d\n", tsdata->header_errors);
}
static DEVICE_ATTR_RO(header_errors);
/* m06 only */
static ssize_t crc_errors_show(struct device *dev,
struct device_attribute *attr, char *buf)
{
struct i2c_client *client = to_i2c_client(dev);
struct edt_ft5x06_ts_data *tsdata = i2c_get_clientdata(client);
return sysfs_emit(buf, "%d\n", tsdata->crc_errors);
}
static DEVICE_ATTR_RO(crc_errors);
static struct attribute *edt_ft5x06_attrs[] = {
&edt_ft5x06_attr_gain.dattr.attr,
&edt_ft5x06_attr_offset.dattr.attr,
&edt_ft5x06_attr_offset_x.dattr.attr,
&edt_ft5x06_attr_offset_y.dattr.attr,
&edt_ft5x06_attr_threshold.dattr.attr,
&edt_ft5x06_attr_report_rate.dattr.attr,
&dev_attr_model.attr,
&dev_attr_fw_version.attr,
&dev_attr_header_errors.attr,
&dev_attr_crc_errors.attr,
NULL
};
static const struct attribute_group edt_ft5x06_attr_group = {
.attrs = edt_ft5x06_attrs,
};
static void edt_ft5x06_restore_reg_parameters(struct edt_ft5x06_ts_data *tsdata)
{
struct edt_reg_addr *reg_addr = &tsdata->reg_addr;
struct regmap *regmap = tsdata->regmap;
regmap_write(regmap, reg_addr->reg_threshold, tsdata->threshold);
regmap_write(regmap, reg_addr->reg_gain, tsdata->gain);
if (reg_addr->reg_offset != NO_REGISTER)
regmap_write(regmap, reg_addr->reg_offset, tsdata->offset);
if (reg_addr->reg_offset_x != NO_REGISTER)
regmap_write(regmap, reg_addr->reg_offset_x, tsdata->offset_x);
if (reg_addr->reg_offset_y != NO_REGISTER)
regmap_write(regmap, reg_addr->reg_offset_y, tsdata->offset_y);
if (reg_addr->reg_report_rate != NO_REGISTER)
regmap_write(regmap, reg_addr->reg_report_rate,
tsdata->report_rate);
}
#ifdef CONFIG_DEBUG_FS
static int edt_ft5x06_factory_mode(struct edt_ft5x06_ts_data *tsdata)
{
struct i2c_client *client = tsdata->client;
int retries = EDT_SWITCH_MODE_RETRIES;
unsigned int val;
int error;
if (tsdata->version != EDT_M06) {
dev_err(&client->dev,
"No factory mode support for non-M06 devices\n");
return -EINVAL;
}
disable_irq(client->irq);
if (!tsdata->raw_buffer) {
tsdata->raw_bufsize = tsdata->num_x * tsdata->num_y *
sizeof(u16);
tsdata->raw_buffer = kzalloc(tsdata->raw_bufsize, GFP_KERNEL);
if (!tsdata->raw_buffer) {
error = -ENOMEM;
goto err_out;
}
}
/* mode register is 0x3c when in the work mode */
error = regmap_write(tsdata->regmap, WORK_REGISTER_OPMODE, 0x03);
if (error) {
dev_err(&client->dev,
"failed to switch to factory mode, error %d\n", error);
goto err_out;
}
tsdata->factory_mode = true;
do {
mdelay(EDT_SWITCH_MODE_DELAY);
/* mode register is 0x01 when in factory mode */
error = regmap_read(tsdata->regmap, FACTORY_REGISTER_OPMODE,
&val);
if (!error && val == 0x03)
break;
} while (--retries > 0);
if (retries == 0) {
dev_err(&client->dev, "not in factory mode after %dms.\n",
EDT_SWITCH_MODE_RETRIES * EDT_SWITCH_MODE_DELAY);
error = -EIO;
goto err_out;
}
return 0;
err_out:
kfree(tsdata->raw_buffer);
tsdata->raw_buffer = NULL;
tsdata->factory_mode = false;
enable_irq(client->irq);
return error;
}
static int edt_ft5x06_work_mode(struct edt_ft5x06_ts_data *tsdata)
{
struct i2c_client *client = tsdata->client;
int retries = EDT_SWITCH_MODE_RETRIES;
unsigned int val;
int error;
/* mode register is 0x01 when in the factory mode */
error = regmap_write(tsdata->regmap, FACTORY_REGISTER_OPMODE, 0x1);
if (error) {
dev_err(&client->dev,
"failed to switch to work mode, error: %d\n", error);
return error;
}
tsdata->factory_mode = false;
do {
mdelay(EDT_SWITCH_MODE_DELAY);
/* mode register is 0x01 when in factory mode */
error = regmap_read(tsdata->regmap, WORK_REGISTER_OPMODE, &val);
if (!error && val == 0x01)
break;
} while (--retries > 0);
if (retries == 0) {
dev_err(&client->dev, "not in work mode after %dms.\n",
EDT_SWITCH_MODE_RETRIES * EDT_SWITCH_MODE_DELAY);
tsdata->factory_mode = true;
return -EIO;
}
kfree(tsdata->raw_buffer);
tsdata->raw_buffer = NULL;
edt_ft5x06_restore_reg_parameters(tsdata);
enable_irq(client->irq);
return 0;
}
static int edt_ft5x06_debugfs_mode_get(void *data, u64 *mode)
{
struct edt_ft5x06_ts_data *tsdata = data;
*mode = tsdata->factory_mode;
return 0;
};
static int edt_ft5x06_debugfs_mode_set(void *data, u64 mode)
{
struct edt_ft5x06_ts_data *tsdata = data;
int retval = 0;
if (mode > 1)
return -ERANGE;
mutex_lock(&tsdata->mutex);
if (mode != tsdata->factory_mode) {
retval = mode ? edt_ft5x06_factory_mode(tsdata) :
edt_ft5x06_work_mode(tsdata);
}
mutex_unlock(&tsdata->mutex);
return retval;
};
DEFINE_SIMPLE_ATTRIBUTE(debugfs_mode_fops, edt_ft5x06_debugfs_mode_get,
edt_ft5x06_debugfs_mode_set, "%llu\n");
static ssize_t edt_ft5x06_debugfs_raw_data_read(struct file *file,
char __user *buf, size_t count,
loff_t *off)
{
struct edt_ft5x06_ts_data *tsdata = file->private_data;
struct i2c_client *client = tsdata->client;
int retries = EDT_RAW_DATA_RETRIES;
unsigned int val;
int i, error;
size_t read = 0;
int colbytes;
u8 *rdbuf;
if (*off < 0 || *off >= tsdata->raw_bufsize)
return 0;
mutex_lock(&tsdata->mutex);
if (!tsdata->factory_mode || !tsdata->raw_buffer) {
error = -EIO;
goto out;
}
error = regmap_write(tsdata->regmap, 0x08, 0x01);
if (error) {
dev_err(&client->dev,
"failed to write 0x08 register, error %d\n", error);
goto out;
}
do {
usleep_range(EDT_RAW_DATA_DELAY, EDT_RAW_DATA_DELAY + 100);
error = regmap_read(tsdata->regmap, 0x08, &val);
if (error) {
dev_err(&client->dev,
"failed to read 0x08 register, error %d\n",
error);
goto out;
}
if (val == 1)
break;
} while (--retries > 0);
if (retries == 0) {
dev_err(&client->dev,
"timed out waiting for register to settle\n");
error = -ETIMEDOUT;
goto out;
}
rdbuf = tsdata->raw_buffer;
colbytes = tsdata->num_y * sizeof(u16);
for (i = 0; i < tsdata->num_x; i++) {
rdbuf[0] = i; /* column index */
error = regmap_bulk_read(tsdata->regmap, 0xf5, rdbuf, colbytes);
if (error)
goto out;
rdbuf += colbytes;
}
read = min_t(size_t, count, tsdata->raw_bufsize - *off);
if (copy_to_user(buf, tsdata->raw_buffer + *off, read)) {
error = -EFAULT;
goto out;
}
*off += read;
out:
mutex_unlock(&tsdata->mutex);
return error ?: read;
};
static const struct file_operations debugfs_raw_data_fops = {
.open = simple_open,
.read = edt_ft5x06_debugfs_raw_data_read,
};
static void edt_ft5x06_ts_prepare_debugfs(struct edt_ft5x06_ts_data *tsdata,
const char *debugfs_name)
{
tsdata->debug_dir = debugfs_create_dir(debugfs_name, NULL);
debugfs_create_u16("num_x", S_IRUSR, tsdata->debug_dir, &tsdata->num_x);
debugfs_create_u16("num_y", S_IRUSR, tsdata->debug_dir, &tsdata->num_y);
debugfs_create_file("mode", S_IRUSR | S_IWUSR,
tsdata->debug_dir, tsdata, &debugfs_mode_fops);
debugfs_create_file("raw_data", S_IRUSR,
tsdata->debug_dir, tsdata, &debugfs_raw_data_fops);
}
static void edt_ft5x06_ts_teardown_debugfs(struct edt_ft5x06_ts_data *tsdata)
{
debugfs_remove_recursive(tsdata->debug_dir);
kfree(tsdata->raw_buffer);
}
#else
static int edt_ft5x06_factory_mode(struct edt_ft5x06_ts_data *tsdata)
{
return -ENOSYS;
}
static void edt_ft5x06_ts_prepare_debugfs(struct edt_ft5x06_ts_data *tsdata,
const char *debugfs_name)
{
}
static void edt_ft5x06_ts_teardown_debugfs(struct edt_ft5x06_ts_data *tsdata)
{
}
#endif /* CONFIG_DEBUGFS */
static int edt_ft5x06_ts_identify(struct i2c_client *client,
struct edt_ft5x06_ts_data *tsdata)
{
u8 rdbuf[EDT_NAME_LEN];
char *p;
int error;
char *model_name = tsdata->name;
char *fw_version = tsdata->fw_version;
/* see what we find if we assume it is a M06 *
* if we get less than EDT_NAME_LEN, we don't want
* to have garbage in there
*/
memset(rdbuf, 0, sizeof(rdbuf));
error = regmap_bulk_read(tsdata->regmap, 0xBB, rdbuf, EDT_NAME_LEN - 1);
if (error)
return error;
/* Probe content for something consistent.
* M06 starts with a response byte, M12 gives the data directly.
* M09/Generic does not provide model number information.
*/
if (!strncasecmp(rdbuf + 1, "EP0", 3)) {
tsdata->version = EDT_M06;
/* remove last '$' end marker */
rdbuf[EDT_NAME_LEN - 1] = '\0';
if (rdbuf[EDT_NAME_LEN - 2] == '$')
rdbuf[EDT_NAME_LEN - 2] = '\0';
/* look for Model/Version separator */
p = strchr(rdbuf, '*');
if (p)
*p++ = '\0';
strscpy(model_name, rdbuf + 1, EDT_NAME_LEN);
strscpy(fw_version, p ? p : "", EDT_NAME_LEN);
regmap_exit(tsdata->regmap);
tsdata->regmap = regmap_init_i2c(client,
&edt_M06_i2c_regmap_config);
if (IS_ERR(tsdata->regmap)) {
dev_err(&client->dev, "regmap allocation failed\n");
return PTR_ERR(tsdata->regmap);
}
} else if (!strncasecmp(rdbuf, "EP0", 3)) {
tsdata->version = EDT_M12;
/* remove last '$' end marker */
rdbuf[EDT_NAME_LEN - 2] = '\0';
if (rdbuf[EDT_NAME_LEN - 3] == '$')
rdbuf[EDT_NAME_LEN - 3] = '\0';
/* look for Model/Version separator */
p = strchr(rdbuf, '*');
if (p)
*p++ = '\0';
strscpy(model_name, rdbuf, EDT_NAME_LEN);
strscpy(fw_version, p ? p : "", EDT_NAME_LEN);
} else {
/* If it is not an EDT M06/M12 touchscreen, then the model
* detection is a bit hairy. The different ft5x06
* firmwares around don't reliably implement the
* identification registers. Well, we'll take a shot.
*
* The main difference between generic focaltec based
* touches and EDT M09 is that we know how to retrieve
* the max coordinates for the latter.
*/
tsdata->version = GENERIC_FT;
error = regmap_bulk_read(tsdata->regmap, 0xA6, rdbuf, 2);
if (error)
return error;
strscpy(fw_version, rdbuf, 2);
error = regmap_bulk_read(tsdata->regmap, 0xA8, rdbuf, 1);
if (error)
return error;
/* This "model identification" is not exact. Unfortunately
* not all firmwares for the ft5x06 put useful values in
* the identification registers.
*/
switch (rdbuf[0]) {
case 0x11: /* EDT EP0110M09 */
case 0x35: /* EDT EP0350M09 */
case 0x43: /* EDT EP0430M09 */
case 0x50: /* EDT EP0500M09 */
case 0x57: /* EDT EP0570M09 */
case 0x70: /* EDT EP0700M09 */
tsdata->version = EDT_M09;
snprintf(model_name, EDT_NAME_LEN, "EP0%i%i0M09",
rdbuf[0] >> 4, rdbuf[0] & 0x0F);
break;
case 0xa1: /* EDT EP1010ML00 */
tsdata->version = EDT_M09;
snprintf(model_name, EDT_NAME_LEN, "EP%i%i0ML00",
rdbuf[0] >> 4, rdbuf[0] & 0x0F);
break;
case 0x5a: /* Solomon Goldentek Display */
snprintf(model_name, EDT_NAME_LEN, "GKTW50SCED1R0");
break;
case 0x59: /* Evervision Display with FT5xx6 TS */
tsdata->version = EV_FT;
error = regmap_bulk_read(tsdata->regmap, 0x53, rdbuf, 1);
if (error)
return error;
strscpy(fw_version, rdbuf, 1);
snprintf(model_name, EDT_NAME_LEN,
"EVERVISION-FT5726NEi");
break;
default:
snprintf(model_name, EDT_NAME_LEN,
"generic ft5x06 (%02x)",
rdbuf[0]);
break;
}
}
return 0;
}
static void edt_ft5x06_ts_get_defaults(struct device *dev,
struct edt_ft5x06_ts_data *tsdata)
{
struct edt_reg_addr *reg_addr = &tsdata->reg_addr;
struct regmap *regmap = tsdata->regmap;
u32 val;
int error;
error = device_property_read_u32(dev, "threshold", &val);
if (!error) {
regmap_write(regmap, reg_addr->reg_threshold, val);
tsdata->threshold = val;
}
error = device_property_read_u32(dev, "gain", &val);
if (!error) {
regmap_write(regmap, reg_addr->reg_gain, val);
tsdata->gain = val;
}
error = device_property_read_u32(dev, "offset", &val);
if (!error) {
if (reg_addr->reg_offset != NO_REGISTER)
regmap_write(regmap, reg_addr->reg_offset, val);
tsdata->offset = val;
}
error = device_property_read_u32(dev, "offset-x", &val);
if (!error) {
if (reg_addr->reg_offset_x != NO_REGISTER)
regmap_write(regmap, reg_addr->reg_offset_x, val);
tsdata->offset_x = val;
}
error = device_property_read_u32(dev, "offset-y", &val);
if (!error) {
if (reg_addr->reg_offset_y != NO_REGISTER)
regmap_write(regmap, reg_addr->reg_offset_y, val);
tsdata->offset_y = val;
}
}
static void edt_ft5x06_ts_get_parameters(struct edt_ft5x06_ts_data *tsdata)
{
struct edt_reg_addr *reg_addr = &tsdata->reg_addr;
struct regmap *regmap = tsdata->regmap;
unsigned int val;
regmap_read(regmap, reg_addr->reg_threshold, &tsdata->threshold);
regmap_read(regmap, reg_addr->reg_gain, &tsdata->gain);
if (reg_addr->reg_offset != NO_REGISTER)
regmap_read(regmap, reg_addr->reg_offset, &tsdata->offset);
if (reg_addr->reg_offset_x != NO_REGISTER)
regmap_read(regmap, reg_addr->reg_offset_x, &tsdata->offset_x);
if (reg_addr->reg_offset_y != NO_REGISTER)
regmap_read(regmap, reg_addr->reg_offset_y, &tsdata->offset_y);
if (reg_addr->reg_report_rate != NO_REGISTER)
regmap_read(regmap, reg_addr->reg_report_rate,
&tsdata->report_rate);
tsdata->num_x = EDT_DEFAULT_NUM_X;
if (reg_addr->reg_num_x != NO_REGISTER) {
if (!regmap_read(regmap, reg_addr->reg_num_x, &val))
tsdata->num_x = val;
}
tsdata->num_y = EDT_DEFAULT_NUM_Y;
if (reg_addr->reg_num_y != NO_REGISTER) {
if (!regmap_read(regmap, reg_addr->reg_num_y, &val))
tsdata->num_y = val;
}
}
static void edt_ft5x06_ts_set_tdata_parameters(struct edt_ft5x06_ts_data *tsdata)
{
int crclen;
if (tsdata->version == EDT_M06) {
tsdata->tdata_cmd = 0xf9;
tsdata->tdata_offset = 5;
tsdata->point_len = 4;
crclen = 1;
} else {
tsdata->tdata_cmd = 0x0;
tsdata->tdata_offset = 3;
tsdata->point_len = 6;
crclen = 0;
}
tsdata->tdata_len = tsdata->point_len * tsdata->max_support_points +
tsdata->tdata_offset + crclen;
}
static void edt_ft5x06_ts_set_regs(struct edt_ft5x06_ts_data *tsdata)
{
struct edt_reg_addr *reg_addr = &tsdata->reg_addr;
switch (tsdata->version) {
case EDT_M06:
reg_addr->reg_threshold = WORK_REGISTER_THRESHOLD;
reg_addr->reg_report_rate = WORK_REGISTER_REPORT_RATE;
reg_addr->reg_gain = WORK_REGISTER_GAIN;
reg_addr->reg_offset = WORK_REGISTER_OFFSET;
reg_addr->reg_offset_x = NO_REGISTER;
reg_addr->reg_offset_y = NO_REGISTER;
reg_addr->reg_num_x = WORK_REGISTER_NUM_X;
reg_addr->reg_num_y = WORK_REGISTER_NUM_Y;
break;
case EDT_M09:
case EDT_M12:
reg_addr->reg_threshold = M09_REGISTER_THRESHOLD;
reg_addr->reg_report_rate = tsdata->version == EDT_M12 ?
M12_REGISTER_REPORT_RATE : NO_REGISTER;
reg_addr->reg_gain = M09_REGISTER_GAIN;
reg_addr->reg_offset = M09_REGISTER_OFFSET;
reg_addr->reg_offset_x = NO_REGISTER;
reg_addr->reg_offset_y = NO_REGISTER;
reg_addr->reg_num_x = M09_REGISTER_NUM_X;
reg_addr->reg_num_y = M09_REGISTER_NUM_Y;
break;
case EV_FT:
reg_addr->reg_threshold = EV_REGISTER_THRESHOLD;
reg_addr->reg_report_rate = NO_REGISTER;
reg_addr->reg_gain = EV_REGISTER_GAIN;
reg_addr->reg_offset = NO_REGISTER;
reg_addr->reg_offset_x = EV_REGISTER_OFFSET_X;
reg_addr->reg_offset_y = EV_REGISTER_OFFSET_Y;
reg_addr->reg_num_x = NO_REGISTER;
reg_addr->reg_num_y = NO_REGISTER;
break;
case GENERIC_FT:
/* this is a guesswork */
reg_addr->reg_threshold = M09_REGISTER_THRESHOLD;
reg_addr->reg_report_rate = NO_REGISTER;
reg_addr->reg_gain = M09_REGISTER_GAIN;
reg_addr->reg_offset = M09_REGISTER_OFFSET;
reg_addr->reg_offset_x = NO_REGISTER;
reg_addr->reg_offset_y = NO_REGISTER;
reg_addr->reg_num_x = NO_REGISTER;
reg_addr->reg_num_y = NO_REGISTER;
break;
}
}
static void edt_ft5x06_disable_regulators(void *arg)
{
struct edt_ft5x06_ts_data *data = arg;
regulator_disable(data->vcc);
regulator_disable(data->iovcc);
}
static int edt_ft5x06_ts_probe(struct i2c_client *client)
{
const struct i2c_device_id *id = i2c_client_get_device_id(client);
const struct edt_i2c_chip_data *chip_data;
struct edt_ft5x06_ts_data *tsdata;
unsigned int val;
struct input_dev *input;
unsigned long irq_flags;
int error;
u32 report_rate;
dev_dbg(&client->dev, "probing for EDT FT5x06 I2C\n");
tsdata = devm_kzalloc(&client->dev, sizeof(*tsdata), GFP_KERNEL);
if (!tsdata) {
dev_err(&client->dev, "failed to allocate driver data.\n");
return -ENOMEM;
}
tsdata->regmap = regmap_init_i2c(client, &edt_ft5x06_i2c_regmap_config);
if (IS_ERR(tsdata->regmap)) {
dev_err(&client->dev, "regmap allocation failed\n");
return PTR_ERR(tsdata->regmap);
}
chip_data = device_get_match_data(&client->dev);
if (!chip_data)
chip_data = (const struct edt_i2c_chip_data *)id->driver_data;
if (!chip_data || !chip_data->max_support_points) {
dev_err(&client->dev, "invalid or missing chip data\n");
return -EINVAL;
}
tsdata->max_support_points = chip_data->max_support_points;
tsdata->vcc = devm_regulator_get(&client->dev, "vcc");
if (IS_ERR(tsdata->vcc)) {
error = PTR_ERR(tsdata->vcc);
if (error != -EPROBE_DEFER)
dev_err(&client->dev,
"failed to request regulator: %d\n", error);
return error;
}
tsdata->iovcc = devm_regulator_get(&client->dev, "iovcc");
if (IS_ERR(tsdata->iovcc)) {
error = PTR_ERR(tsdata->iovcc);
if (error != -EPROBE_DEFER)
dev_err(&client->dev,
"failed to request iovcc regulator: %d\n", error);
return error;
}
error = regulator_enable(tsdata->iovcc);
if (error < 0) {
dev_err(&client->dev, "failed to enable iovcc: %d\n", error);
return error;
}
/* Delay enabling VCC for > 10us (T_ivd) after IOVCC */
usleep_range(10, 100);
error = regulator_enable(tsdata->vcc);
if (error < 0) {
dev_err(&client->dev, "failed to enable vcc: %d\n", error);
regulator_disable(tsdata->iovcc);
return error;
}
error = devm_add_action_or_reset(&client->dev,
edt_ft5x06_disable_regulators,
tsdata);
if (error)
return error;
tsdata->reset_gpio = devm_gpiod_get_optional(&client->dev,
"reset", GPIOD_OUT_HIGH);
if (IS_ERR(tsdata->reset_gpio)) {
error = PTR_ERR(tsdata->reset_gpio);
dev_err(&client->dev,
"Failed to request GPIO reset pin, error %d\n", error);
return error;
}
tsdata->wake_gpio = devm_gpiod_get_optional(&client->dev,
"wake", GPIOD_OUT_LOW);
if (IS_ERR(tsdata->wake_gpio)) {
error = PTR_ERR(tsdata->wake_gpio);
dev_err(&client->dev,
"Failed to request GPIO wake pin, error %d\n", error);
return error;
}
/*
* Check which sleep modes we can support. Power-off requieres the
* reset-pin to ensure correct power-down/power-up behaviour. Start with
* the EDT_PMODE_POWEROFF test since this is the deepest possible sleep
* mode.
*/
if (tsdata->reset_gpio)
tsdata->suspend_mode = EDT_PMODE_POWEROFF;
else if (tsdata->wake_gpio)
tsdata->suspend_mode = EDT_PMODE_HIBERNATE;
else
tsdata->suspend_mode = EDT_PMODE_NOT_SUPPORTED;
if (tsdata->wake_gpio) {
usleep_range(5000, 6000);
gpiod_set_value_cansleep(tsdata->wake_gpio, 1);
usleep_range(5000, 6000);
}
if (tsdata->reset_gpio) {
usleep_range(5000, 6000);
gpiod_set_value_cansleep(tsdata->reset_gpio, 0);
msleep(300);
}
input = devm_input_allocate_device(&client->dev);
if (!input) {
dev_err(&client->dev, "failed to allocate input device.\n");
return -ENOMEM;
}
mutex_init(&tsdata->mutex);
tsdata->client = client;
tsdata->input = input;
tsdata->factory_mode = false;
i2c_set_clientdata(client, tsdata);
error = edt_ft5x06_ts_identify(client, tsdata);
if (error) {
dev_err(&client->dev, "touchscreen probe failed\n");
return error;
}
/*
* Dummy read access. EP0700MLP1 returns bogus data on the first
* register read access and ignores writes.
*/
regmap_read(tsdata->regmap, 0x00, &val);
edt_ft5x06_ts_set_tdata_parameters(tsdata);
edt_ft5x06_ts_set_regs(tsdata);
edt_ft5x06_ts_get_defaults(&client->dev, tsdata);
edt_ft5x06_ts_get_parameters(tsdata);
if (tsdata->reg_addr.reg_report_rate != NO_REGISTER &&
!device_property_read_u32(&client->dev,
"report-rate-hz", &report_rate)) {
if (tsdata->version == EDT_M06)
tsdata->report_rate = clamp_val(report_rate, 30, 140);
else
tsdata->report_rate = clamp_val(report_rate, 1, 255);
if (report_rate != tsdata->report_rate)
dev_warn(&client->dev,
"report-rate %dHz is unsupported, use %dHz\n",
report_rate, tsdata->report_rate);
if (tsdata->version == EDT_M06)
tsdata->report_rate /= 10;
regmap_write(tsdata->regmap, tsdata->reg_addr.reg_report_rate,
tsdata->report_rate);
}
dev_dbg(&client->dev,
"Model \"%s\", Rev. \"%s\", %dx%d sensors\n",
tsdata->name, tsdata->fw_version, tsdata->num_x, tsdata->num_y);
input->name = tsdata->name;
input->id.bustype = BUS_I2C;
input->dev.parent = &client->dev;
input_set_abs_params(input, ABS_MT_POSITION_X,
0, tsdata->num_x * 64 - 1, 0, 0);
input_set_abs_params(input, ABS_MT_POSITION_Y,
0, tsdata->num_y * 64 - 1, 0, 0);
touchscreen_parse_properties(input, true, &tsdata->prop);
error = input_mt_init_slots(input, tsdata->max_support_points,
INPUT_MT_DIRECT);
if (error) {
dev_err(&client->dev, "Unable to init MT slots.\n");
return error;
}
irq_flags = irq_get_trigger_type(client->irq);
if (irq_flags == IRQF_TRIGGER_NONE)
irq_flags = IRQF_TRIGGER_FALLING;
irq_flags |= IRQF_ONESHOT;
error = devm_request_threaded_irq(&client->dev, client->irq,
NULL, edt_ft5x06_ts_isr, irq_flags,
client->name, tsdata);
if (error) {
dev_err(&client->dev, "Unable to request touchscreen IRQ.\n");
return error;
}
error = devm_device_add_group(&client->dev, &edt_ft5x06_attr_group);
if (error)
return error;
error = input_register_device(input);
if (error)
return error;
edt_ft5x06_ts_prepare_debugfs(tsdata, dev_driver_string(&client->dev));
dev_dbg(&client->dev,
"EDT FT5x06 initialized: IRQ %d, WAKE pin %d, Reset pin %d.\n",
client->irq,
tsdata->wake_gpio ? desc_to_gpio(tsdata->wake_gpio) : -1,
tsdata->reset_gpio ? desc_to_gpio(tsdata->reset_gpio) : -1);
return 0;
}
static void edt_ft5x06_ts_remove(struct i2c_client *client)
{
struct edt_ft5x06_ts_data *tsdata = i2c_get_clientdata(client);
edt_ft5x06_ts_teardown_debugfs(tsdata);
regmap_exit(tsdata->regmap);
}
static int edt_ft5x06_ts_suspend(struct device *dev)
{
struct i2c_client *client = to_i2c_client(dev);
struct edt_ft5x06_ts_data *tsdata = i2c_get_clientdata(client);
struct gpio_desc *reset_gpio = tsdata->reset_gpio;
int ret;
if (device_may_wakeup(dev))
return 0;
if (tsdata->suspend_mode == EDT_PMODE_NOT_SUPPORTED)
return 0;
/* Enter hibernate mode. */
ret = regmap_write(tsdata->regmap, PMOD_REGISTER_OPMODE,
PMOD_REGISTER_HIBERNATE);
if (ret)
dev_warn(dev, "Failed to set hibernate mode\n");
if (tsdata->suspend_mode == EDT_PMODE_HIBERNATE)
return 0;
/*
* Power-off according the datasheet. Cut the power may leaf the irq
* line in an undefined state depending on the host pull resistor
* settings. Disable the irq to avoid adjusting each host till the
* device is back in a full functional state.
*/
disable_irq(tsdata->client->irq);
gpiod_set_value_cansleep(reset_gpio, 1);
usleep_range(1000, 2000);
ret = regulator_disable(tsdata->vcc);
if (ret)
dev_warn(dev, "Failed to disable vcc\n");
ret = regulator_disable(tsdata->iovcc);
if (ret)
dev_warn(dev, "Failed to disable iovcc\n");
return 0;
}
static int edt_ft5x06_ts_resume(struct device *dev)
{
struct i2c_client *client = to_i2c_client(dev);
struct edt_ft5x06_ts_data *tsdata = i2c_get_clientdata(client);
int ret = 0;
if (device_may_wakeup(dev))
return 0;
if (tsdata->suspend_mode == EDT_PMODE_NOT_SUPPORTED)
return 0;
if (tsdata->suspend_mode == EDT_PMODE_POWEROFF) {
struct gpio_desc *reset_gpio = tsdata->reset_gpio;
/*
* We can't check if the regulator is a dummy or a real
* regulator. So we need to specify the 5ms reset time (T_rst)
* here instead of the 100us T_rtp time. We also need to wait
* 300ms in case it was a real supply and the power was cutted
* of. Toggle the reset pin is also a way to exit the hibernate
* mode.
*/
gpiod_set_value_cansleep(reset_gpio, 1);
usleep_range(5000, 6000);
ret = regulator_enable(tsdata->iovcc);
if (ret) {
dev_err(dev, "Failed to enable iovcc\n");
return ret;
}
/* Delay enabling VCC for > 10us (T_ivd) after IOVCC */
usleep_range(10, 100);
ret = regulator_enable(tsdata->vcc);
if (ret) {
dev_err(dev, "Failed to enable vcc\n");
regulator_disable(tsdata->iovcc);
return ret;
}
usleep_range(1000, 2000);
gpiod_set_value_cansleep(reset_gpio, 0);
msleep(300);
edt_ft5x06_restore_reg_parameters(tsdata);
enable_irq(tsdata->client->irq);
if (tsdata->factory_mode)
ret = edt_ft5x06_factory_mode(tsdata);
} else {
struct gpio_desc *wake_gpio = tsdata->wake_gpio;
gpiod_set_value_cansleep(wake_gpio, 0);
usleep_range(5000, 6000);
gpiod_set_value_cansleep(wake_gpio, 1);
}
return ret;
}
static DEFINE_SIMPLE_DEV_PM_OPS(edt_ft5x06_ts_pm_ops,
edt_ft5x06_ts_suspend, edt_ft5x06_ts_resume);
static const struct edt_i2c_chip_data edt_ft5x06_data = {
.max_support_points = 5,
};
static const struct edt_i2c_chip_data edt_ft5506_data = {
.max_support_points = 10,
};
static const struct edt_i2c_chip_data edt_ft6236_data = {
.max_support_points = 2,
};
static const struct i2c_device_id edt_ft5x06_ts_id[] = {
{ .name = "edt-ft5x06", .driver_data = (long)&edt_ft5x06_data },
{ .name = "edt-ft5506", .driver_data = (long)&edt_ft5506_data },
{ .name = "ev-ft5726", .driver_data = (long)&edt_ft5506_data },
/* Note no edt- prefix for compatibility with the ft6236.c driver */
{ .name = "ft6236", .driver_data = (long)&edt_ft6236_data },
{ /* sentinel */ }
};
MODULE_DEVICE_TABLE(i2c, edt_ft5x06_ts_id);
static const struct of_device_id edt_ft5x06_of_match[] = {
{ .compatible = "edt,edt-ft5206", .data = &edt_ft5x06_data },
{ .compatible = "edt,edt-ft5306", .data = &edt_ft5x06_data },
{ .compatible = "edt,edt-ft5406", .data = &edt_ft5x06_data },
{ .compatible = "edt,edt-ft5506", .data = &edt_ft5506_data },
{ .compatible = "evervision,ev-ft5726", .data = &edt_ft5506_data },
/* Note focaltech vendor prefix for compatibility with ft6236.c */
{ .compatible = "focaltech,ft6236", .data = &edt_ft6236_data },
{ /* sentinel */ }
};
MODULE_DEVICE_TABLE(of, edt_ft5x06_of_match);
static struct i2c_driver edt_ft5x06_ts_driver = {
.driver = {
.name = "edt_ft5x06",
.of_match_table = edt_ft5x06_of_match,
.pm = pm_sleep_ptr(&edt_ft5x06_ts_pm_ops),
.probe_type = PROBE_PREFER_ASYNCHRONOUS,
},
.id_table = edt_ft5x06_ts_id,
.probe = edt_ft5x06_ts_probe,
.remove = edt_ft5x06_ts_remove,
};
module_i2c_driver(edt_ft5x06_ts_driver);
MODULE_AUTHOR("Simon Budig <simon.budig@kernelconcepts.de>");
MODULE_DESCRIPTION("EDT FT5x06 I2C Touchscreen Driver");
MODULE_LICENSE("GPL v2");
Reference in New Issue View Git Blame Copy Permalink