480 lines
12 KiB
C
480 lines
12 KiB
C
// SPDX-License-Identifier: GPL-2.0-only
|
|
/*
|
|
* Driver for Semtech SX8654 I2C touchscreen controller.
|
|
*
|
|
* Copyright (c) 2015 Armadeus Systems
|
|
* Sébastien Szymanski <sebastien.szymanski@armadeus.com>
|
|
*
|
|
* Using code from:
|
|
* - sx865x.c
|
|
* Copyright (c) 2013 U-MoBo Srl
|
|
* Pierluigi Passaro <p.passaro@u-mobo.com>
|
|
* - sx8650.c
|
|
* Copyright (c) 2009 Wayne Roberts
|
|
* - tsc2007.c
|
|
* Copyright (c) 2008 Kwangwoo Lee
|
|
* - ads7846.c
|
|
* Copyright (c) 2005 David Brownell
|
|
* Copyright (c) 2006 Nokia Corporation
|
|
* - corgi_ts.c
|
|
* Copyright (C) 2004-2005 Richard Purdie
|
|
* - omap_ts.[hc], ads7846.h, ts_osk.c
|
|
* Copyright (C) 2002 MontaVista Software
|
|
* Copyright (C) 2004 Texas Instruments
|
|
* Copyright (C) 2005 Dirk Behme
|
|
*/
|
|
|
|
#include <linux/bitops.h>
|
|
#include <linux/delay.h>
|
|
#include <linux/gpio/consumer.h>
|
|
#include <linux/i2c.h>
|
|
#include <linux/input.h>
|
|
#include <linux/input/touchscreen.h>
|
|
#include <linux/interrupt.h>
|
|
#include <linux/irq.h>
|
|
#include <linux/module.h>
|
|
#include <linux/of.h>
|
|
|
|
/* register addresses */
|
|
#define I2C_REG_TOUCH0 0x00
|
|
#define I2C_REG_TOUCH1 0x01
|
|
#define I2C_REG_CHANMASK 0x04
|
|
#define I2C_REG_IRQMASK 0x22
|
|
#define I2C_REG_IRQSRC 0x23
|
|
#define I2C_REG_SOFTRESET 0x3f
|
|
|
|
#define I2C_REG_SX8650_STAT 0x05
|
|
#define SX8650_STAT_CONVIRQ BIT(7)
|
|
|
|
/* commands */
|
|
#define CMD_READ_REGISTER 0x40
|
|
#define CMD_PENTRG 0xe0
|
|
|
|
/* value for I2C_REG_SOFTRESET */
|
|
#define SOFTRESET_VALUE 0xde
|
|
|
|
/* bits for I2C_REG_IRQSRC */
|
|
#define IRQ_PENTOUCH_TOUCHCONVDONE BIT(3)
|
|
#define IRQ_PENRELEASE BIT(2)
|
|
|
|
/* bits for RegTouch1 */
|
|
#define CONDIRQ 0x20
|
|
#define RPDNT_100K 0x00
|
|
#define FILT_7SA 0x03
|
|
|
|
/* bits for I2C_REG_CHANMASK */
|
|
#define CONV_X BIT(7)
|
|
#define CONV_Y BIT(6)
|
|
|
|
/* coordinates rate: higher nibble of CTRL0 register */
|
|
#define RATE_MANUAL 0x00
|
|
#define RATE_5000CPS 0xf0
|
|
|
|
/* power delay: lower nibble of CTRL0 register */
|
|
#define POWDLY_1_1MS 0x0b
|
|
|
|
/* for sx8650, as we have no pen release IRQ there: timeout in ns following the
|
|
* last PENIRQ after which we assume the pen is lifted.
|
|
*/
|
|
#define SX8650_PENIRQ_TIMEOUT msecs_to_jiffies(10)
|
|
|
|
#define MAX_12BIT ((1 << 12) - 1)
|
|
#define MAX_I2C_READ_LEN 10 /* see datasheet section 5.1.5 */
|
|
|
|
/* channel definition */
|
|
#define CH_X 0x00
|
|
#define CH_Y 0x01
|
|
|
|
struct sx865x_data {
|
|
u8 cmd_manual;
|
|
u8 chan_mask;
|
|
bool has_irq_penrelease;
|
|
bool has_reg_irqmask;
|
|
irq_handler_t irqh;
|
|
};
|
|
|
|
struct sx8654 {
|
|
struct input_dev *input;
|
|
struct i2c_client *client;
|
|
struct gpio_desc *gpio_reset;
|
|
|
|
spinlock_t lock; /* for input reporting from irq/timer */
|
|
struct timer_list timer;
|
|
|
|
struct touchscreen_properties props;
|
|
|
|
const struct sx865x_data *data;
|
|
};
|
|
|
|
static inline void sx865x_penrelease(struct sx8654 *ts)
|
|
{
|
|
struct input_dev *input_dev = ts->input;
|
|
|
|
input_report_key(input_dev, BTN_TOUCH, 0);
|
|
input_sync(input_dev);
|
|
}
|
|
|
|
static void sx865x_penrelease_timer_handler(struct timer_list *t)
|
|
{
|
|
struct sx8654 *ts = from_timer(ts, t, timer);
|
|
unsigned long flags;
|
|
|
|
spin_lock_irqsave(&ts->lock, flags);
|
|
sx865x_penrelease(ts);
|
|
spin_unlock_irqrestore(&ts->lock, flags);
|
|
dev_dbg(&ts->client->dev, "penrelease by timer\n");
|
|
}
|
|
|
|
static irqreturn_t sx8650_irq(int irq, void *handle)
|
|
{
|
|
struct sx8654 *ts = handle;
|
|
struct device *dev = &ts->client->dev;
|
|
int len, i;
|
|
unsigned long flags;
|
|
u8 stat;
|
|
u16 x, y;
|
|
u16 ch;
|
|
u16 chdata;
|
|
__be16 data[MAX_I2C_READ_LEN / sizeof(__be16)];
|
|
u8 nchan = hweight32(ts->data->chan_mask);
|
|
u8 readlen = nchan * sizeof(*data);
|
|
|
|
stat = i2c_smbus_read_byte_data(ts->client, CMD_READ_REGISTER
|
|
| I2C_REG_SX8650_STAT);
|
|
|
|
if (!(stat & SX8650_STAT_CONVIRQ)) {
|
|
dev_dbg(dev, "%s ignore stat [0x%02x]", __func__, stat);
|
|
return IRQ_HANDLED;
|
|
}
|
|
|
|
len = i2c_master_recv(ts->client, (u8 *)data, readlen);
|
|
if (len != readlen) {
|
|
dev_dbg(dev, "ignore short recv (%d)\n", len);
|
|
return IRQ_HANDLED;
|
|
}
|
|
|
|
spin_lock_irqsave(&ts->lock, flags);
|
|
|
|
x = 0;
|
|
y = 0;
|
|
for (i = 0; i < nchan; i++) {
|
|
chdata = be16_to_cpu(data[i]);
|
|
|
|
if (unlikely(chdata == 0xFFFF)) {
|
|
dev_dbg(dev, "invalid qualified data @ %d\n", i);
|
|
continue;
|
|
} else if (unlikely(chdata & 0x8000)) {
|
|
dev_warn(dev, "hibit @ %d [0x%04x]\n", i, chdata);
|
|
continue;
|
|
}
|
|
|
|
ch = chdata >> 12;
|
|
if (ch == CH_X)
|
|
x = chdata & MAX_12BIT;
|
|
else if (ch == CH_Y)
|
|
y = chdata & MAX_12BIT;
|
|
else
|
|
dev_warn(dev, "unknown channel %d [0x%04x]\n", ch,
|
|
chdata);
|
|
}
|
|
|
|
touchscreen_report_pos(ts->input, &ts->props, x, y, false);
|
|
input_report_key(ts->input, BTN_TOUCH, 1);
|
|
input_sync(ts->input);
|
|
dev_dbg(dev, "point(%4d,%4d)\n", x, y);
|
|
|
|
mod_timer(&ts->timer, jiffies + SX8650_PENIRQ_TIMEOUT);
|
|
spin_unlock_irqrestore(&ts->lock, flags);
|
|
|
|
return IRQ_HANDLED;
|
|
}
|
|
|
|
static irqreturn_t sx8654_irq(int irq, void *handle)
|
|
{
|
|
struct sx8654 *sx8654 = handle;
|
|
int irqsrc;
|
|
u8 data[4];
|
|
unsigned int x, y;
|
|
int retval;
|
|
|
|
irqsrc = i2c_smbus_read_byte_data(sx8654->client,
|
|
CMD_READ_REGISTER | I2C_REG_IRQSRC);
|
|
dev_dbg(&sx8654->client->dev, "irqsrc = 0x%x", irqsrc);
|
|
|
|
if (irqsrc < 0)
|
|
goto out;
|
|
|
|
if (irqsrc & IRQ_PENRELEASE) {
|
|
dev_dbg(&sx8654->client->dev, "pen release interrupt");
|
|
|
|
input_report_key(sx8654->input, BTN_TOUCH, 0);
|
|
input_sync(sx8654->input);
|
|
}
|
|
|
|
if (irqsrc & IRQ_PENTOUCH_TOUCHCONVDONE) {
|
|
dev_dbg(&sx8654->client->dev, "pen touch interrupt");
|
|
|
|
retval = i2c_master_recv(sx8654->client, data, sizeof(data));
|
|
if (retval != sizeof(data))
|
|
goto out;
|
|
|
|
/* invalid data */
|
|
if (unlikely(data[0] & 0x80 || data[2] & 0x80))
|
|
goto out;
|
|
|
|
x = ((data[0] & 0xf) << 8) | (data[1]);
|
|
y = ((data[2] & 0xf) << 8) | (data[3]);
|
|
|
|
touchscreen_report_pos(sx8654->input, &sx8654->props, x, y,
|
|
false);
|
|
input_report_key(sx8654->input, BTN_TOUCH, 1);
|
|
input_sync(sx8654->input);
|
|
|
|
dev_dbg(&sx8654->client->dev, "point(%4d,%4d)\n", x, y);
|
|
}
|
|
|
|
out:
|
|
return IRQ_HANDLED;
|
|
}
|
|
|
|
static int sx8654_reset(struct sx8654 *ts)
|
|
{
|
|
int err;
|
|
|
|
if (ts->gpio_reset) {
|
|
gpiod_set_value_cansleep(ts->gpio_reset, 1);
|
|
udelay(2); /* Tpulse > 1µs */
|
|
gpiod_set_value_cansleep(ts->gpio_reset, 0);
|
|
} else {
|
|
dev_dbg(&ts->client->dev, "NRST unavailable, try softreset\n");
|
|
err = i2c_smbus_write_byte_data(ts->client, I2C_REG_SOFTRESET,
|
|
SOFTRESET_VALUE);
|
|
if (err)
|
|
return err;
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int sx8654_open(struct input_dev *dev)
|
|
{
|
|
struct sx8654 *sx8654 = input_get_drvdata(dev);
|
|
struct i2c_client *client = sx8654->client;
|
|
int error;
|
|
|
|
/* enable pen trigger mode */
|
|
error = i2c_smbus_write_byte_data(client, I2C_REG_TOUCH0,
|
|
RATE_5000CPS | POWDLY_1_1MS);
|
|
if (error) {
|
|
dev_err(&client->dev, "writing to I2C_REG_TOUCH0 failed");
|
|
return error;
|
|
}
|
|
|
|
error = i2c_smbus_write_byte(client, CMD_PENTRG);
|
|
if (error) {
|
|
dev_err(&client->dev, "writing command CMD_PENTRG failed");
|
|
return error;
|
|
}
|
|
|
|
enable_irq(client->irq);
|
|
|
|
return 0;
|
|
}
|
|
|
|
static void sx8654_close(struct input_dev *dev)
|
|
{
|
|
struct sx8654 *sx8654 = input_get_drvdata(dev);
|
|
struct i2c_client *client = sx8654->client;
|
|
int error;
|
|
|
|
disable_irq(client->irq);
|
|
|
|
if (!sx8654->data->has_irq_penrelease)
|
|
del_timer_sync(&sx8654->timer);
|
|
|
|
/* enable manual mode mode */
|
|
error = i2c_smbus_write_byte(client, sx8654->data->cmd_manual);
|
|
if (error) {
|
|
dev_err(&client->dev, "writing command CMD_MANUAL failed");
|
|
return;
|
|
}
|
|
|
|
error = i2c_smbus_write_byte_data(client, I2C_REG_TOUCH0, RATE_MANUAL);
|
|
if (error) {
|
|
dev_err(&client->dev, "writing to I2C_REG_TOUCH0 failed");
|
|
return;
|
|
}
|
|
}
|
|
|
|
static int sx8654_probe(struct i2c_client *client)
|
|
{
|
|
const struct i2c_device_id *id = i2c_client_get_device_id(client);
|
|
struct sx8654 *sx8654;
|
|
struct input_dev *input;
|
|
int error;
|
|
|
|
if (!i2c_check_functionality(client->adapter,
|
|
I2C_FUNC_SMBUS_READ_WORD_DATA))
|
|
return -ENXIO;
|
|
|
|
sx8654 = devm_kzalloc(&client->dev, sizeof(*sx8654), GFP_KERNEL);
|
|
if (!sx8654)
|
|
return -ENOMEM;
|
|
|
|
sx8654->gpio_reset = devm_gpiod_get_optional(&client->dev, "reset",
|
|
GPIOD_OUT_HIGH);
|
|
if (IS_ERR(sx8654->gpio_reset)) {
|
|
error = PTR_ERR(sx8654->gpio_reset);
|
|
if (error != -EPROBE_DEFER)
|
|
dev_err(&client->dev, "unable to get reset-gpio: %d\n",
|
|
error);
|
|
return error;
|
|
}
|
|
dev_dbg(&client->dev, "got GPIO reset pin\n");
|
|
|
|
sx8654->data = device_get_match_data(&client->dev);
|
|
if (!sx8654->data)
|
|
sx8654->data = (const struct sx865x_data *)id->driver_data;
|
|
if (!sx8654->data) {
|
|
dev_err(&client->dev, "invalid or missing device data\n");
|
|
return -EINVAL;
|
|
}
|
|
|
|
if (!sx8654->data->has_irq_penrelease) {
|
|
dev_dbg(&client->dev, "use timer for penrelease\n");
|
|
timer_setup(&sx8654->timer, sx865x_penrelease_timer_handler, 0);
|
|
spin_lock_init(&sx8654->lock);
|
|
}
|
|
|
|
input = devm_input_allocate_device(&client->dev);
|
|
if (!input)
|
|
return -ENOMEM;
|
|
|
|
input->name = "SX8654 I2C Touchscreen";
|
|
input->id.bustype = BUS_I2C;
|
|
input->dev.parent = &client->dev;
|
|
input->open = sx8654_open;
|
|
input->close = sx8654_close;
|
|
|
|
__set_bit(INPUT_PROP_DIRECT, input->propbit);
|
|
input_set_capability(input, EV_KEY, BTN_TOUCH);
|
|
input_set_abs_params(input, ABS_X, 0, MAX_12BIT, 0, 0);
|
|
input_set_abs_params(input, ABS_Y, 0, MAX_12BIT, 0, 0);
|
|
|
|
touchscreen_parse_properties(input, false, &sx8654->props);
|
|
|
|
sx8654->client = client;
|
|
sx8654->input = input;
|
|
|
|
input_set_drvdata(sx8654->input, sx8654);
|
|
|
|
error = sx8654_reset(sx8654);
|
|
if (error) {
|
|
dev_err(&client->dev, "reset failed");
|
|
return error;
|
|
}
|
|
|
|
error = i2c_smbus_write_byte_data(client, I2C_REG_CHANMASK,
|
|
sx8654->data->chan_mask);
|
|
if (error) {
|
|
dev_err(&client->dev, "writing to I2C_REG_CHANMASK failed");
|
|
return error;
|
|
}
|
|
|
|
if (sx8654->data->has_reg_irqmask) {
|
|
error = i2c_smbus_write_byte_data(client, I2C_REG_IRQMASK,
|
|
IRQ_PENTOUCH_TOUCHCONVDONE |
|
|
IRQ_PENRELEASE);
|
|
if (error) {
|
|
dev_err(&client->dev, "writing I2C_REG_IRQMASK failed");
|
|
return error;
|
|
}
|
|
}
|
|
|
|
error = i2c_smbus_write_byte_data(client, I2C_REG_TOUCH1,
|
|
CONDIRQ | RPDNT_100K | FILT_7SA);
|
|
if (error) {
|
|
dev_err(&client->dev, "writing to I2C_REG_TOUCH1 failed");
|
|
return error;
|
|
}
|
|
|
|
error = devm_request_threaded_irq(&client->dev, client->irq,
|
|
NULL, sx8654->data->irqh,
|
|
IRQF_ONESHOT,
|
|
client->name, sx8654);
|
|
if (error) {
|
|
dev_err(&client->dev,
|
|
"Failed to enable IRQ %d, error: %d\n",
|
|
client->irq, error);
|
|
return error;
|
|
}
|
|
|
|
/* Disable the IRQ, we'll enable it in sx8654_open() */
|
|
disable_irq(client->irq);
|
|
|
|
error = input_register_device(sx8654->input);
|
|
if (error)
|
|
return error;
|
|
|
|
return 0;
|
|
}
|
|
|
|
static const struct sx865x_data sx8650_data = {
|
|
.cmd_manual = 0xb0,
|
|
.has_irq_penrelease = false,
|
|
.has_reg_irqmask = false,
|
|
.chan_mask = (CONV_X | CONV_Y),
|
|
.irqh = sx8650_irq,
|
|
};
|
|
|
|
static const struct sx865x_data sx8654_data = {
|
|
.cmd_manual = 0xc0,
|
|
.has_irq_penrelease = true,
|
|
.has_reg_irqmask = true,
|
|
.chan_mask = (CONV_X | CONV_Y),
|
|
.irqh = sx8654_irq,
|
|
};
|
|
|
|
#ifdef CONFIG_OF
|
|
static const struct of_device_id sx8654_of_match[] = {
|
|
{
|
|
.compatible = "semtech,sx8650",
|
|
.data = &sx8650_data,
|
|
}, {
|
|
.compatible = "semtech,sx8654",
|
|
.data = &sx8654_data,
|
|
}, {
|
|
.compatible = "semtech,sx8655",
|
|
.data = &sx8654_data,
|
|
}, {
|
|
.compatible = "semtech,sx8656",
|
|
.data = &sx8654_data,
|
|
},
|
|
{ }
|
|
};
|
|
MODULE_DEVICE_TABLE(of, sx8654_of_match);
|
|
#endif
|
|
|
|
static const struct i2c_device_id sx8654_id_table[] = {
|
|
{ .name = "semtech_sx8650", .driver_data = (long)&sx8650_data },
|
|
{ .name = "semtech_sx8654", .driver_data = (long)&sx8654_data },
|
|
{ .name = "semtech_sx8655", .driver_data = (long)&sx8654_data },
|
|
{ .name = "semtech_sx8656", .driver_data = (long)&sx8654_data },
|
|
{ }
|
|
};
|
|
MODULE_DEVICE_TABLE(i2c, sx8654_id_table);
|
|
|
|
static struct i2c_driver sx8654_driver = {
|
|
.driver = {
|
|
.name = "sx8654",
|
|
.of_match_table = of_match_ptr(sx8654_of_match),
|
|
},
|
|
.id_table = sx8654_id_table,
|
|
.probe = sx8654_probe,
|
|
};
|
|
module_i2c_driver(sx8654_driver);
|
|
|
|
MODULE_AUTHOR("Sébastien Szymanski <sebastien.szymanski@armadeus.com>");
|
|
MODULE_DESCRIPTION("Semtech SX8654 I2C Touchscreen Driver");
|
|
MODULE_LICENSE("GPL");
|