138 lines
3.9 KiB
YAML
138 lines
3.9 KiB
YAML
# SPDX-License-Identifier: (GPL-2.0-only or BSD-2-Clause)
|
|
%YAML 1.2
|
|
---
|
|
$id: http://devicetree.org/schemas/display/panel/panel-mipi-dbi-spi.yaml#
|
|
$schema: http://devicetree.org/meta-schemas/core.yaml#
|
|
|
|
title: MIPI DBI SPI Panel
|
|
|
|
maintainers:
|
|
- Noralf Trønnes <noralf@tronnes.org>
|
|
|
|
description: |
|
|
This binding is for display panels using a MIPI DBI compatible controller
|
|
in SPI mode.
|
|
|
|
The MIPI Alliance Standard for Display Bus Interface defines the electrical
|
|
and logical interfaces for display controllers historically used in mobile
|
|
phones. The standard defines 4 display architecture types and this binding is
|
|
for type 1 which has full frame memory. There are 3 interface types in the
|
|
standard and type C is the serial interface.
|
|
|
|
The standard defines the following interface signals for type C:
|
|
- Power:
|
|
- Vdd: Power supply for display module
|
|
Called power-supply in this binding.
|
|
- Vddi: Logic level supply for interface signals
|
|
Called io-supply in this binding.
|
|
- Interface:
|
|
- CSx: Chip select
|
|
- SCL: Serial clock
|
|
- Dout: Serial out
|
|
- Din: Serial in
|
|
- SDA: Bidrectional in/out
|
|
- D/CX: Data/command selection, high=data, low=command
|
|
Called dc-gpios in this binding.
|
|
- RESX: Reset when low
|
|
Called reset-gpios in this binding.
|
|
|
|
The type C interface has 3 options:
|
|
|
|
- Option 1: 9-bit mode and D/CX as the 9th bit
|
|
| Command | the next command or following data |
|
|
|<0><D7><D6><D5><D4><D3><D2><D1><D0>|<D/CX><D7><D6><D5><D4><D3><D2><D1><D0>|
|
|
|
|
- Option 2: 16-bit mode and D/CX as a 9th bit
|
|
| Command or data |
|
|
|<X><X><X><X><X><X><X><D/CX><D7><D6><D5><D4><D3><D2><D1><D0>|
|
|
|
|
- Option 3: 8-bit mode and D/CX as a separate interface line
|
|
| Command or data |
|
|
|<D7><D6><D5><D4><D3><D2><D1><D0>|
|
|
|
|
The panel resolution is specified using the panel-timing node properties
|
|
hactive (width) and vactive (height). The other mandatory panel-timing
|
|
properties should be set to zero except clock-frequency which can be
|
|
optionally set to inform about the actual pixel clock frequency.
|
|
|
|
If the panel is wired to the controller at an offset specify this using
|
|
hback-porch (x-offset) and vback-porch (y-offset).
|
|
|
|
allOf:
|
|
- $ref: panel-common.yaml#
|
|
- $ref: /schemas/spi/spi-peripheral-props.yaml#
|
|
|
|
properties:
|
|
compatible:
|
|
items:
|
|
- enum:
|
|
- sainsmart18
|
|
- shineworld,lh133k
|
|
- const: panel-mipi-dbi-spi
|
|
|
|
write-only:
|
|
type: boolean
|
|
description:
|
|
Controller is not readable (ie. Din (MISO on the SPI interface) is not
|
|
wired up).
|
|
|
|
dc-gpios:
|
|
maxItems: 1
|
|
description: |
|
|
Controller data/command selection (D/CX) in 4-line SPI mode.
|
|
If not set, the controller is in 3-line SPI mode.
|
|
|
|
io-supply:
|
|
description: |
|
|
Logic level supply for interface signals (Vddi).
|
|
No need to set if this is the same as power-supply.
|
|
|
|
spi-3wire: true
|
|
|
|
required:
|
|
- compatible
|
|
- reg
|
|
- width-mm
|
|
- height-mm
|
|
- panel-timing
|
|
|
|
unevaluatedProperties: false
|
|
|
|
examples:
|
|
- |
|
|
#include <dt-bindings/gpio/gpio.h>
|
|
|
|
spi {
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
display@0{
|
|
compatible = "sainsmart18", "panel-mipi-dbi-spi";
|
|
reg = <0>;
|
|
spi-max-frequency = <40000000>;
|
|
|
|
dc-gpios = <&gpio 24 GPIO_ACTIVE_HIGH>;
|
|
reset-gpios = <&gpio 25 GPIO_ACTIVE_HIGH>;
|
|
write-only;
|
|
|
|
backlight = <&backlight>;
|
|
|
|
width-mm = <35>;
|
|
height-mm = <28>;
|
|
|
|
panel-timing {
|
|
hactive = <160>;
|
|
vactive = <128>;
|
|
hback-porch = <0>;
|
|
vback-porch = <0>;
|
|
clock-frequency = <0>;
|
|
hfront-porch = <0>;
|
|
hsync-len = <0>;
|
|
vfront-porch = <0>;
|
|
vsync-len = <0>;
|
|
};
|
|
};
|
|
};
|
|
|
|
...
|