130 lines
2.7 KiB
Plaintext
130 lines
2.7 KiB
Plaintext
Vitesse VSC73xx Switches
|
|
========================
|
|
|
|
This defines device tree bindings for the Vitesse VSC73xx switch chips.
|
|
The Vitesse company has been acquired by Microsemi and Microsemi has
|
|
been acquired Microchip but retains this vendor branding.
|
|
|
|
The currently supported switch chips are:
|
|
Vitesse VSC7385 SparX-G5 5+1-port Integrated Gigabit Ethernet Switch
|
|
Vitesse VSC7388 SparX-G8 8-port Integrated Gigabit Ethernet Switch
|
|
Vitesse VSC7395 SparX-G5e 5+1-port Integrated Gigabit Ethernet Switch
|
|
Vitesse VSC7398 SparX-G8e 8-port Integrated Gigabit Ethernet Switch
|
|
|
|
This switch could have two different management interface.
|
|
|
|
If SPI interface is used, the device tree node is an SPI device so it must
|
|
reside inside a SPI bus device tree node, see spi/spi-bus.txt
|
|
|
|
When the chip is connected to a parallel memory bus and work in memory-mapped
|
|
I/O mode, a platform device is used to represent the vsc73xx. In this case it
|
|
must reside inside a platform bus device tree node.
|
|
|
|
Required properties:
|
|
|
|
- compatible: must be exactly one of:
|
|
"vitesse,vsc7385"
|
|
"vitesse,vsc7388"
|
|
"vitesse,vsc7395"
|
|
"vitesse,vsc7398"
|
|
- gpio-controller: indicates that this switch is also a GPIO controller,
|
|
see gpio/gpio.txt
|
|
- #gpio-cells: this must be set to <2> and indicates that we are a twocell
|
|
GPIO controller, see gpio/gpio.txt
|
|
|
|
Optional properties:
|
|
|
|
- reset-gpios: a handle to a GPIO line that can issue reset of the chip.
|
|
It should be tagged as active low.
|
|
|
|
Required subnodes:
|
|
|
|
See net/dsa/dsa.txt for a list of additional required and optional properties
|
|
and subnodes of DSA switches.
|
|
|
|
Examples:
|
|
|
|
SPI:
|
|
switch@0 {
|
|
compatible = "vitesse,vsc7395";
|
|
reg = <0>;
|
|
/* Specified for 2.5 MHz or below */
|
|
spi-max-frequency = <2500000>;
|
|
gpio-controller;
|
|
#gpio-cells = <2>;
|
|
|
|
ports {
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
port@0 {
|
|
reg = <0>;
|
|
label = "lan1";
|
|
};
|
|
port@1 {
|
|
reg = <1>;
|
|
label = "lan2";
|
|
};
|
|
port@2 {
|
|
reg = <2>;
|
|
label = "lan3";
|
|
};
|
|
port@3 {
|
|
reg = <3>;
|
|
label = "lan4";
|
|
};
|
|
vsc: port@6 {
|
|
reg = <6>;
|
|
ethernet = <&gmac1>;
|
|
phy-mode = "rgmii";
|
|
fixed-link {
|
|
speed = <1000>;
|
|
full-duplex;
|
|
pause;
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
Platform:
|
|
switch@2,0 {
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
compatible = "vitesse,vsc7385";
|
|
reg = <0x2 0x0 0x20000>;
|
|
reset-gpios = <&gpio0 12 GPIO_ACTIVE_LOW>;
|
|
|
|
ports {
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
port@0 {
|
|
reg = <0>;
|
|
label = "lan1";
|
|
};
|
|
port@1 {
|
|
reg = <1>;
|
|
label = "lan2";
|
|
};
|
|
port@2 {
|
|
reg = <2>;
|
|
label = "lan3";
|
|
};
|
|
port@3 {
|
|
reg = <3>;
|
|
label = "lan4";
|
|
};
|
|
vsc: port@6 {
|
|
reg = <6>;
|
|
ethernet = <&enet0>;
|
|
phy-mode = "rgmii";
|
|
fixed-link {
|
|
speed = <1000>;
|
|
full-duplex;
|
|
pause;
|
|
};
|
|
};
|
|
};
|
|
|
|
};
|