228 lines
7.1 KiB
YAML
228 lines
7.1 KiB
YAML
# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
|
|
%YAML 1.2
|
|
---
|
|
$id: http://devicetree.org/schemas/pinctrl/mediatek,pinctrl-mt6795.yaml#
|
|
$schema: http://devicetree.org/meta-schemas/core.yaml#
|
|
|
|
title: Mediatek MT6795 Pin Controller
|
|
|
|
maintainers:
|
|
- AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
|
|
- Sean Wang <sean.wang@kernel.org>
|
|
|
|
description: |
|
|
The Mediatek's Pin controller is used to control SoC pins.
|
|
|
|
properties:
|
|
compatible:
|
|
const: mediatek,mt6795-pinctrl
|
|
|
|
gpio-controller: true
|
|
|
|
'#gpio-cells':
|
|
description: |
|
|
Number of cells in GPIO specifier. Since the generic GPIO binding is used,
|
|
the amount of cells must be specified as 2. See the below
|
|
mentioned gpio binding representation for description of particular cells.
|
|
const: 2
|
|
|
|
gpio-ranges:
|
|
description: GPIO valid number range.
|
|
maxItems: 1
|
|
|
|
reg:
|
|
description:
|
|
Physical address base for gpio base and eint registers.
|
|
minItems: 2
|
|
|
|
reg-names:
|
|
items:
|
|
- const: base
|
|
- const: eint
|
|
|
|
interrupt-controller: true
|
|
|
|
'#interrupt-cells':
|
|
const: 2
|
|
|
|
interrupts:
|
|
description: Interrupt outputs to the system interrupt controller (sysirq).
|
|
minItems: 1
|
|
items:
|
|
- description: EINT interrupt
|
|
- description: EINT event_b interrupt
|
|
|
|
# PIN CONFIGURATION NODES
|
|
patternProperties:
|
|
'-pins$':
|
|
type: object
|
|
additionalProperties: false
|
|
patternProperties:
|
|
'^pins':
|
|
type: object
|
|
additionalProperties: false
|
|
description: |
|
|
A pinctrl node should contain at least one subnodes representing the
|
|
pinctrl groups available on the machine. Each subnode will list the
|
|
pins it needs, and how they should be configured, with regard to muxer
|
|
configuration, pullups, drive strength, input enable/disable and
|
|
input schmitt.
|
|
An example of using macro:
|
|
pincontroller {
|
|
/* GPIO0 set as multifunction GPIO0 */
|
|
gpio-pins {
|
|
pins {
|
|
pinmux = <PINMUX_GPIO0__FUNC_GPIO0>;
|
|
}
|
|
};
|
|
/* GPIO45 set as multifunction SDA0 */
|
|
i2c0-pins {
|
|
pins {
|
|
pinmux = <PINMUX_GPIO45__FUNC_SDA0>;
|
|
}
|
|
};
|
|
};
|
|
$ref: "pinmux-node.yaml"
|
|
|
|
properties:
|
|
pinmux:
|
|
description: |
|
|
Integer array, represents gpio pin number and mux setting.
|
|
Supported pin number and mux varies for different SoCs, and are
|
|
defined as macros in dt-bindings/pinctrl/<soc>-pinfunc.h
|
|
directly.
|
|
|
|
drive-strength:
|
|
enum: [2, 4, 6, 8, 10, 12, 14, 16]
|
|
|
|
bias-pull-down:
|
|
oneOf:
|
|
- type: boolean
|
|
- enum: [100, 101, 102, 103]
|
|
description: mt6795 pull down PUPD/R0/R1 type define value.
|
|
description: |
|
|
For normal pull down type, it is not necessary to specify R1R0
|
|
values; When pull down type is PUPD/R0/R1, adding R1R0 defines
|
|
will set different resistance values.
|
|
|
|
bias-pull-up:
|
|
oneOf:
|
|
- type: boolean
|
|
- enum: [100, 101, 102, 103]
|
|
description: mt6795 pull up PUPD/R0/R1 type define value.
|
|
description: |
|
|
For normal pull up type, it is not necessary to specify R1R0
|
|
values; When pull up type is PUPD/R0/R1, adding R1R0 defines
|
|
will set different resistance values.
|
|
|
|
bias-disable: true
|
|
|
|
output-high: true
|
|
|
|
output-low: true
|
|
|
|
input-enable: true
|
|
|
|
input-disable: true
|
|
|
|
input-schmitt-enable: true
|
|
|
|
input-schmitt-disable: true
|
|
|
|
mediatek,pull-up-adv:
|
|
description: |
|
|
Pull up setings for 2 pull resistors, R0 and R1. User can
|
|
configure those special pins. Valid arguments are described as below:
|
|
0: (R1, R0) = (0, 0) which means R1 disabled and R0 disabled.
|
|
1: (R1, R0) = (0, 1) which means R1 disabled and R0 enabled.
|
|
2: (R1, R0) = (1, 0) which means R1 enabled and R0 disabled.
|
|
3: (R1, R0) = (1, 1) which means R1 enabled and R0 enabled.
|
|
$ref: /schemas/types.yaml#/definitions/uint32
|
|
enum: [0, 1, 2, 3]
|
|
|
|
mediatek,pull-down-adv:
|
|
description: |
|
|
Pull down settings for 2 pull resistors, R0 and R1. User can
|
|
configure those special pins. Valid arguments are described as below:
|
|
0: (R1, R0) = (0, 0) which means R1 disabled and R0 disabled.
|
|
1: (R1, R0) = (0, 1) which means R1 disabled and R0 enabled.
|
|
2: (R1, R0) = (1, 0) which means R1 enabled and R0 disabled.
|
|
3: (R1, R0) = (1, 1) which means R1 enabled and R0 enabled.
|
|
$ref: /schemas/types.yaml#/definitions/uint32
|
|
enum: [0, 1, 2, 3]
|
|
|
|
required:
|
|
- pinmux
|
|
|
|
allOf:
|
|
- $ref: "pinctrl.yaml#"
|
|
|
|
required:
|
|
- compatible
|
|
- reg
|
|
- reg-names
|
|
- interrupts
|
|
- interrupt-controller
|
|
- '#interrupt-cells'
|
|
- gpio-controller
|
|
- '#gpio-cells'
|
|
- gpio-ranges
|
|
|
|
additionalProperties: false
|
|
|
|
examples:
|
|
- |
|
|
#include <dt-bindings/interrupt-controller/arm-gic.h>
|
|
#include <dt-bindings/interrupt-controller/irq.h>
|
|
#include <dt-bindings/pinctrl/mt6795-pinfunc.h>
|
|
|
|
soc {
|
|
#address-cells = <2>;
|
|
#size-cells = <2>;
|
|
|
|
pio: pinctrl@10005000 {
|
|
compatible = "mediatek,mt6795-pinctrl";
|
|
reg = <0 0x10005000 0 0x1000>, <0 0x1000b000 0 0x1000>;
|
|
reg-names = "base", "eint";
|
|
gpio-controller;
|
|
#gpio-cells = <2>;
|
|
gpio-ranges = <&pio 0 0 196>;
|
|
interrupt-controller;
|
|
interrupts = <GIC_SPI 153 IRQ_TYPE_LEVEL_HIGH>;
|
|
#interrupt-cells = <2>;
|
|
|
|
i2c0-pins {
|
|
pins-sda-scl {
|
|
pinmux = <PINMUX_GPIO45__FUNC_SDA0>,
|
|
<PINMUX_GPIO46__FUNC_SCL0>;
|
|
};
|
|
};
|
|
|
|
mmc0-pins {
|
|
pins-cmd-dat {
|
|
pinmux = <PINMUX_GPIO154__FUNC_MSDC0_DAT0>,
|
|
<PINMUX_GPIO155__FUNC_MSDC0_DAT1>,
|
|
<PINMUX_GPIO156__FUNC_MSDC0_DAT2>,
|
|
<PINMUX_GPIO157__FUNC_MSDC0_DAT3>,
|
|
<PINMUX_GPIO158__FUNC_MSDC0_DAT4>,
|
|
<PINMUX_GPIO159__FUNC_MSDC0_DAT5>,
|
|
<PINMUX_GPIO160__FUNC_MSDC0_DAT6>,
|
|
<PINMUX_GPIO161__FUNC_MSDC0_DAT7>,
|
|
<PINMUX_GPIO162__FUNC_MSDC0_CMD>;
|
|
input-enable;
|
|
bias-pull-up = <MTK_PUPD_SET_R1R0_01>;
|
|
};
|
|
|
|
pins-clk {
|
|
pinmux = <PINMUX_GPIO163__FUNC_MSDC0_CLK>;
|
|
bias-pull-down = <MTK_PUPD_SET_R1R0_10>;
|
|
};
|
|
|
|
pins-rst {
|
|
pinmux = <PINMUX_GPIO165__FUNC_MSDC0_RSTB>;
|
|
bias-pull-up = <MTK_PUPD_SET_R1R0_10>;
|
|
};
|
|
};
|
|
};
|
|
};
|