308 lines
9.7 KiB
YAML
308 lines
9.7 KiB
YAML
# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
|
|
%YAML 1.2
|
|
---
|
|
$id: http://devicetree.org/schemas/pinctrl/starfive,jh7100-pinctrl.yaml#
|
|
$schema: http://devicetree.org/meta-schemas/core.yaml#
|
|
|
|
title: StarFive JH7100 Pin Controller
|
|
|
|
description: |
|
|
Bindings for the JH7100 RISC-V SoC from StarFive Ltd.
|
|
|
|
Out of the SoC's many pins only the ones named PAD_GPIO[0] to PAD_GPIO[63]
|
|
and PAD_FUNC_SHARE[0] to PAD_FUNC_SHARE[141] can be multiplexed and have
|
|
configurable bias, drive strength, schmitt trigger etc. The SoC has an
|
|
interesting 2-layered approach to pin muxing best illustrated by the diagram
|
|
below.
|
|
|
|
Signal group 0, 1, ... or 6
|
|
___|___
|
|
| |
|
|
LCD output -----------------| |
|
|
CMOS Camera interface ------| |--- PAD_GPIO[0]
|
|
Ethernet PHY interface -----| MUX |--- PAD_GPIO[1]
|
|
... | | ...
|
|
| |--- PAD_GPIO[63]
|
|
-------- GPIO0 ------------| |
|
|
| -------|-- GPIO1 --------| |--- PAD_FUNC_SHARE[0]
|
|
| | | | | |--- PAD_FUNC_SHARE[1]
|
|
| | | | ... | | ...
|
|
| | | | | |--- PAD_FUNC_SHARE[141]
|
|
| | -----|---|-- GPIO63 ---| |
|
|
| | | | | | -------
|
|
UART0 UART1 --
|
|
|
|
|
|
The big MUX in the diagram only has 7 different ways of mapping peripherals
|
|
on the left to pins on the right. StarFive calls the 7 configurations "signal
|
|
groups".
|
|
However some peripherals have their I/O go through the 64 "GPIOs". The
|
|
diagram only shows UART0 and UART1, but this also includes a number of other
|
|
UARTs, I2Cs, SPIs, PWMs etc. All these peripherals are connected to all 64
|
|
GPIOs such that any GPIO can be set up to be controlled by any of the
|
|
peripherals.
|
|
Note that signal group 0 doesn't map any of the GPIOs to pins, and only
|
|
signal group 1 maps the GPIOs to the pins named PAD_GPIO[0] to PAD_GPIO[63].
|
|
|
|
maintainers:
|
|
- Emil Renner Berthing <kernel@esmil.dk>
|
|
- Drew Fustini <drew@beagleboard.org>
|
|
|
|
properties:
|
|
compatible:
|
|
const: starfive,jh7100-pinctrl
|
|
|
|
reg:
|
|
minItems: 2
|
|
maxItems: 2
|
|
|
|
reg-names:
|
|
items:
|
|
- const: gpio
|
|
- const: padctl
|
|
|
|
clocks:
|
|
maxItems: 1
|
|
|
|
resets:
|
|
maxItems: 1
|
|
|
|
gpio-controller: true
|
|
|
|
"#gpio-cells":
|
|
const: 2
|
|
|
|
interrupts:
|
|
maxItems: 1
|
|
description: The GPIO parent interrupt.
|
|
|
|
interrupt-controller: true
|
|
|
|
"#interrupt-cells":
|
|
const: 2
|
|
|
|
starfive,signal-group:
|
|
description: |
|
|
Select one of the 7 signal groups. If this property is not set it
|
|
defaults to the configuration already chosen by the earlier boot stages.
|
|
$ref: /schemas/types.yaml#/definitions/uint32
|
|
enum: [0, 1, 2, 3, 4, 5, 6]
|
|
|
|
required:
|
|
- compatible
|
|
- reg
|
|
- reg-names
|
|
- clocks
|
|
- gpio-controller
|
|
- "#gpio-cells"
|
|
- interrupts
|
|
- interrupt-controller
|
|
- "#interrupt-cells"
|
|
|
|
patternProperties:
|
|
'-[0-9]+$':
|
|
type: object
|
|
patternProperties:
|
|
'-pins$':
|
|
type: object
|
|
description: |
|
|
A pinctrl node should contain at least one subnode representing the
|
|
pinctrl groups available on the machine. Each subnode will list the
|
|
pins it needs, and how they should be configured, with regard to
|
|
muxer configuration, bias, input enable/disable, input schmitt
|
|
trigger enable/disable, slew-rate and drive strength.
|
|
$ref: /schemas/pinctrl/pincfg-node.yaml
|
|
|
|
properties:
|
|
pins:
|
|
description: |
|
|
The list of pin identifiers that properties in the node apply to.
|
|
This should be set using either the PAD_GPIO or PAD_FUNC_SHARE
|
|
macros.
|
|
Either this or "pinmux" has to be specified, but not both.
|
|
$ref: /schemas/pinctrl/pinmux-node.yaml#/properties/pins
|
|
|
|
pinmux:
|
|
description: |
|
|
The list of GPIOs and their mux settings that properties in the
|
|
node apply to. This should be set using the GPIOMUX macro.
|
|
Either this or "pins" has to be specified, but not both.
|
|
$ref: /schemas/pinctrl/pinmux-node.yaml#/properties/pinmux
|
|
|
|
bias-disable: true
|
|
|
|
bias-pull-up:
|
|
type: boolean
|
|
|
|
bias-pull-down:
|
|
type: boolean
|
|
|
|
drive-strength:
|
|
enum: [ 14, 21, 28, 35, 42, 49, 56, 63 ]
|
|
|
|
input-enable: true
|
|
|
|
input-disable: true
|
|
|
|
input-schmitt-enable: true
|
|
|
|
input-schmitt-disable: true
|
|
|
|
slew-rate:
|
|
maximum: 7
|
|
|
|
starfive,strong-pull-up:
|
|
description: enable strong pull-up.
|
|
type: boolean
|
|
|
|
additionalProperties: false
|
|
|
|
additionalProperties: false
|
|
|
|
additionalProperties: false
|
|
|
|
examples:
|
|
- |
|
|
#include <dt-bindings/clock/starfive-jh7100.h>
|
|
#include <dt-bindings/reset/starfive-jh7100.h>
|
|
#include <dt-bindings/pinctrl/pinctrl-starfive-jh7100.h>
|
|
|
|
soc {
|
|
#address-cells = <2>;
|
|
#size-cells = <2>;
|
|
|
|
pinctrl@11910000 {
|
|
compatible = "starfive,jh7100-pinctrl";
|
|
reg = <0x0 0x11910000 0x0 0x10000>,
|
|
<0x0 0x11858000 0x0 0x1000>;
|
|
reg-names = "gpio", "padctl";
|
|
clocks = <&clkgen JH7100_CLK_GPIO_APB>;
|
|
resets = <&clkgen JH7100_RSTN_GPIO_APB>;
|
|
interrupts = <32>;
|
|
gpio-controller;
|
|
#gpio-cells = <2>;
|
|
interrupt-controller;
|
|
#interrupt-cells = <2>;
|
|
starfive,signal-group = <6>;
|
|
|
|
gmac_pins_default: gmac-0 {
|
|
gtxclk-pins {
|
|
pins = <PAD_FUNC_SHARE(115)>;
|
|
bias-pull-up;
|
|
drive-strength = <35>;
|
|
input-enable;
|
|
input-schmitt-enable;
|
|
slew-rate = <0>;
|
|
};
|
|
miitxclk-pins {
|
|
pins = <PAD_FUNC_SHARE(116)>;
|
|
bias-pull-up;
|
|
drive-strength = <14>;
|
|
input-enable;
|
|
input-schmitt-disable;
|
|
slew-rate = <0>;
|
|
};
|
|
tx-pins {
|
|
pins = <PAD_FUNC_SHARE(117)>,
|
|
<PAD_FUNC_SHARE(119)>,
|
|
<PAD_FUNC_SHARE(120)>,
|
|
<PAD_FUNC_SHARE(121)>,
|
|
<PAD_FUNC_SHARE(122)>,
|
|
<PAD_FUNC_SHARE(123)>,
|
|
<PAD_FUNC_SHARE(124)>,
|
|
<PAD_FUNC_SHARE(125)>,
|
|
<PAD_FUNC_SHARE(126)>;
|
|
bias-disable;
|
|
drive-strength = <35>;
|
|
input-disable;
|
|
input-schmitt-disable;
|
|
slew-rate = <0>;
|
|
};
|
|
rxclk-pins {
|
|
pins = <PAD_FUNC_SHARE(127)>;
|
|
bias-pull-up;
|
|
drive-strength = <14>;
|
|
input-enable;
|
|
input-schmitt-disable;
|
|
slew-rate = <6>;
|
|
};
|
|
rxer-pins {
|
|
pins = <PAD_FUNC_SHARE(129)>;
|
|
bias-pull-up;
|
|
drive-strength = <14>;
|
|
input-enable;
|
|
input-schmitt-disable;
|
|
slew-rate = <0>;
|
|
};
|
|
rx-pins {
|
|
pins = <PAD_FUNC_SHARE(128)>,
|
|
<PAD_FUNC_SHARE(130)>,
|
|
<PAD_FUNC_SHARE(131)>,
|
|
<PAD_FUNC_SHARE(132)>,
|
|
<PAD_FUNC_SHARE(133)>,
|
|
<PAD_FUNC_SHARE(134)>,
|
|
<PAD_FUNC_SHARE(135)>,
|
|
<PAD_FUNC_SHARE(136)>,
|
|
<PAD_FUNC_SHARE(137)>,
|
|
<PAD_FUNC_SHARE(138)>,
|
|
<PAD_FUNC_SHARE(139)>,
|
|
<PAD_FUNC_SHARE(140)>,
|
|
<PAD_FUNC_SHARE(141)>;
|
|
bias-pull-up;
|
|
drive-strength = <14>;
|
|
input-enable;
|
|
input-schmitt-enable;
|
|
slew-rate = <0>;
|
|
};
|
|
};
|
|
|
|
i2c0_pins_default: i2c0-0 {
|
|
i2c-pins {
|
|
pinmux = <GPIOMUX(62, GPO_LOW,
|
|
GPO_I2C0_PAD_SCK_OEN,
|
|
GPI_I2C0_PAD_SCK_IN)>,
|
|
<GPIOMUX(61, GPO_LOW,
|
|
GPO_I2C0_PAD_SDA_OEN,
|
|
GPI_I2C0_PAD_SDA_IN)>;
|
|
bias-disable; /* external pull-up */
|
|
input-enable;
|
|
input-schmitt-enable;
|
|
};
|
|
};
|
|
|
|
uart3_pins_default: uart3-0 {
|
|
rx-pins {
|
|
pinmux = <GPIOMUX(13, GPO_LOW, GPO_DISABLE,
|
|
GPI_UART3_PAD_SIN)>;
|
|
bias-pull-up;
|
|
input-enable;
|
|
input-schmitt-enable;
|
|
};
|
|
tx-pins {
|
|
pinmux = <GPIOMUX(14, GPO_UART3_PAD_SOUT,
|
|
GPO_ENABLE, GPI_NONE)>;
|
|
bias-disable;
|
|
input-disable;
|
|
input-schmitt-disable;
|
|
};
|
|
};
|
|
};
|
|
|
|
gmac {
|
|
pinctrl-0 = <&gmac_pins_default>;
|
|
pinctrl-names = "default";
|
|
};
|
|
|
|
i2c {
|
|
pinctrl-0 = <&i2c0_pins_default>;
|
|
pinctrl-names = "default";
|
|
};
|
|
|
|
uart3 {
|
|
pinctrl-0 = <&uart3_pins_default>;
|
|
pinctrl-names = "default";
|
|
};
|
|
};
|
|
|
|
...
|