625 lines
16 KiB
C
625 lines
16 KiB
C
// SPDX-License-Identifier: GPL-2.0+
|
|
/*
|
|
* Marvell 88x2222 dual-port multi-speed ethernet transceiver.
|
|
*
|
|
* Supports:
|
|
* XAUI on the host side.
|
|
* 1000Base-X or 10GBase-R on the line side.
|
|
* SGMII over 1000Base-X.
|
|
*/
|
|
#include <linux/module.h>
|
|
#include <linux/phy.h>
|
|
#include <linux/gpio.h>
|
|
#include <linux/delay.h>
|
|
#include <linux/mdio.h>
|
|
#include <linux/marvell_phy.h>
|
|
#include <linux/of.h>
|
|
#include <linux/of_device.h>
|
|
#include <linux/of_gpio.h>
|
|
#include <linux/sfp.h>
|
|
#include <linux/netdevice.h>
|
|
|
|
/* Port PCS Configuration */
|
|
#define MV_PCS_CONFIG 0xF002
|
|
#define MV_PCS_HOST_XAUI 0x73
|
|
#define MV_PCS_LINE_10GBR (0x71 << 8)
|
|
#define MV_PCS_LINE_1GBX_AN (0x7B << 8)
|
|
#define MV_PCS_LINE_SGMII_AN (0x7F << 8)
|
|
|
|
/* Port Reset and Power Down */
|
|
#define MV_PORT_RST 0xF003
|
|
#define MV_LINE_RST_SW BIT(15)
|
|
#define MV_HOST_RST_SW BIT(7)
|
|
#define MV_PORT_RST_SW (MV_LINE_RST_SW | MV_HOST_RST_SW)
|
|
|
|
/* PMD Receive Signal Detect */
|
|
#define MV_RX_SIGNAL_DETECT 0x000A
|
|
#define MV_RX_SIGNAL_DETECT_GLOBAL BIT(0)
|
|
|
|
/* 1000Base-X/SGMII Control Register */
|
|
#define MV_1GBX_CTRL (0x2000 + MII_BMCR)
|
|
|
|
/* 1000BASE-X/SGMII Status Register */
|
|
#define MV_1GBX_STAT (0x2000 + MII_BMSR)
|
|
|
|
/* 1000Base-X Auto-Negotiation Advertisement Register */
|
|
#define MV_1GBX_ADVERTISE (0x2000 + MII_ADVERTISE)
|
|
|
|
/* 1000Base-X PHY Specific Status Register */
|
|
#define MV_1GBX_PHY_STAT 0xA003
|
|
#define MV_1GBX_PHY_STAT_AN_RESOLVED BIT(11)
|
|
#define MV_1GBX_PHY_STAT_DUPLEX BIT(13)
|
|
#define MV_1GBX_PHY_STAT_SPEED100 BIT(14)
|
|
#define MV_1GBX_PHY_STAT_SPEED1000 BIT(15)
|
|
|
|
#define AUTONEG_TIMEOUT 3
|
|
|
|
struct mv2222_data {
|
|
phy_interface_t line_interface;
|
|
__ETHTOOL_DECLARE_LINK_MODE_MASK(supported);
|
|
bool sfp_link;
|
|
};
|
|
|
|
/* SFI PMA transmit enable */
|
|
static int mv2222_tx_enable(struct phy_device *phydev)
|
|
{
|
|
return phy_clear_bits_mmd(phydev, MDIO_MMD_PMAPMD, MDIO_PMA_TXDIS,
|
|
MDIO_PMD_TXDIS_GLOBAL);
|
|
}
|
|
|
|
/* SFI PMA transmit disable */
|
|
static int mv2222_tx_disable(struct phy_device *phydev)
|
|
{
|
|
return phy_set_bits_mmd(phydev, MDIO_MMD_PMAPMD, MDIO_PMA_TXDIS,
|
|
MDIO_PMD_TXDIS_GLOBAL);
|
|
}
|
|
|
|
static int mv2222_soft_reset(struct phy_device *phydev)
|
|
{
|
|
int val, ret;
|
|
|
|
ret = phy_write_mmd(phydev, MDIO_MMD_VEND2, MV_PORT_RST,
|
|
MV_PORT_RST_SW);
|
|
if (ret < 0)
|
|
return ret;
|
|
|
|
return phy_read_mmd_poll_timeout(phydev, MDIO_MMD_VEND2, MV_PORT_RST,
|
|
val, !(val & MV_PORT_RST_SW),
|
|
5000, 1000000, true);
|
|
}
|
|
|
|
static int mv2222_disable_aneg(struct phy_device *phydev)
|
|
{
|
|
int ret = phy_clear_bits_mmd(phydev, MDIO_MMD_PCS, MV_1GBX_CTRL,
|
|
BMCR_ANENABLE | BMCR_ANRESTART);
|
|
if (ret < 0)
|
|
return ret;
|
|
|
|
return mv2222_soft_reset(phydev);
|
|
}
|
|
|
|
static int mv2222_enable_aneg(struct phy_device *phydev)
|
|
{
|
|
int ret = phy_set_bits_mmd(phydev, MDIO_MMD_PCS, MV_1GBX_CTRL,
|
|
BMCR_ANENABLE | BMCR_RESET);
|
|
if (ret < 0)
|
|
return ret;
|
|
|
|
return mv2222_soft_reset(phydev);
|
|
}
|
|
|
|
static int mv2222_set_sgmii_speed(struct phy_device *phydev)
|
|
{
|
|
struct mv2222_data *priv = phydev->priv;
|
|
|
|
switch (phydev->speed) {
|
|
default:
|
|
case SPEED_1000:
|
|
if ((linkmode_test_bit(ETHTOOL_LINK_MODE_1000baseT_Full_BIT,
|
|
priv->supported) ||
|
|
linkmode_test_bit(ETHTOOL_LINK_MODE_1000baseT_Half_BIT,
|
|
priv->supported)))
|
|
return phy_modify_mmd(phydev, MDIO_MMD_PCS,
|
|
MV_1GBX_CTRL,
|
|
BMCR_SPEED1000 | BMCR_SPEED100,
|
|
BMCR_SPEED1000);
|
|
|
|
fallthrough;
|
|
case SPEED_100:
|
|
if ((linkmode_test_bit(ETHTOOL_LINK_MODE_100baseT_Full_BIT,
|
|
priv->supported) ||
|
|
linkmode_test_bit(ETHTOOL_LINK_MODE_100baseT_Half_BIT,
|
|
priv->supported)))
|
|
return phy_modify_mmd(phydev, MDIO_MMD_PCS,
|
|
MV_1GBX_CTRL,
|
|
BMCR_SPEED1000 | BMCR_SPEED100,
|
|
BMCR_SPEED100);
|
|
fallthrough;
|
|
case SPEED_10:
|
|
if ((linkmode_test_bit(ETHTOOL_LINK_MODE_10baseT_Full_BIT,
|
|
priv->supported) ||
|
|
linkmode_test_bit(ETHTOOL_LINK_MODE_10baseT_Half_BIT,
|
|
priv->supported)))
|
|
return phy_modify_mmd(phydev, MDIO_MMD_PCS,
|
|
MV_1GBX_CTRL,
|
|
BMCR_SPEED1000 | BMCR_SPEED100,
|
|
BMCR_SPEED10);
|
|
|
|
return -EINVAL;
|
|
}
|
|
}
|
|
|
|
static bool mv2222_is_10g_capable(struct phy_device *phydev)
|
|
{
|
|
struct mv2222_data *priv = phydev->priv;
|
|
|
|
return (linkmode_test_bit(ETHTOOL_LINK_MODE_10000baseT_Full_BIT,
|
|
priv->supported) ||
|
|
linkmode_test_bit(ETHTOOL_LINK_MODE_10000baseCR_Full_BIT,
|
|
priv->supported) ||
|
|
linkmode_test_bit(ETHTOOL_LINK_MODE_10000baseSR_Full_BIT,
|
|
priv->supported) ||
|
|
linkmode_test_bit(ETHTOOL_LINK_MODE_10000baseLR_Full_BIT,
|
|
priv->supported) ||
|
|
linkmode_test_bit(ETHTOOL_LINK_MODE_10000baseLRM_Full_BIT,
|
|
priv->supported) ||
|
|
linkmode_test_bit(ETHTOOL_LINK_MODE_10000baseER_Full_BIT,
|
|
priv->supported));
|
|
}
|
|
|
|
static bool mv2222_is_1gbx_capable(struct phy_device *phydev)
|
|
{
|
|
struct mv2222_data *priv = phydev->priv;
|
|
|
|
return linkmode_test_bit(ETHTOOL_LINK_MODE_1000baseX_Full_BIT,
|
|
priv->supported);
|
|
}
|
|
|
|
static bool mv2222_is_sgmii_capable(struct phy_device *phydev)
|
|
{
|
|
struct mv2222_data *priv = phydev->priv;
|
|
|
|
return (linkmode_test_bit(ETHTOOL_LINK_MODE_1000baseT_Full_BIT,
|
|
priv->supported) ||
|
|
linkmode_test_bit(ETHTOOL_LINK_MODE_1000baseT_Half_BIT,
|
|
priv->supported) ||
|
|
linkmode_test_bit(ETHTOOL_LINK_MODE_100baseT_Full_BIT,
|
|
priv->supported) ||
|
|
linkmode_test_bit(ETHTOOL_LINK_MODE_100baseT_Half_BIT,
|
|
priv->supported) ||
|
|
linkmode_test_bit(ETHTOOL_LINK_MODE_10baseT_Full_BIT,
|
|
priv->supported) ||
|
|
linkmode_test_bit(ETHTOOL_LINK_MODE_10baseT_Half_BIT,
|
|
priv->supported));
|
|
}
|
|
|
|
static int mv2222_config_line(struct phy_device *phydev)
|
|
{
|
|
struct mv2222_data *priv = phydev->priv;
|
|
|
|
switch (priv->line_interface) {
|
|
case PHY_INTERFACE_MODE_10GBASER:
|
|
return phy_write_mmd(phydev, MDIO_MMD_VEND2, MV_PCS_CONFIG,
|
|
MV_PCS_HOST_XAUI | MV_PCS_LINE_10GBR);
|
|
case PHY_INTERFACE_MODE_1000BASEX:
|
|
return phy_write_mmd(phydev, MDIO_MMD_VEND2, MV_PCS_CONFIG,
|
|
MV_PCS_HOST_XAUI | MV_PCS_LINE_1GBX_AN);
|
|
case PHY_INTERFACE_MODE_SGMII:
|
|
return phy_write_mmd(phydev, MDIO_MMD_VEND2, MV_PCS_CONFIG,
|
|
MV_PCS_HOST_XAUI | MV_PCS_LINE_SGMII_AN);
|
|
default:
|
|
return -EINVAL;
|
|
}
|
|
}
|
|
|
|
/* Switch between 1G (1000Base-X/SGMII) and 10G (10GBase-R) modes */
|
|
static int mv2222_swap_line_type(struct phy_device *phydev)
|
|
{
|
|
struct mv2222_data *priv = phydev->priv;
|
|
bool changed = false;
|
|
int ret;
|
|
|
|
switch (priv->line_interface) {
|
|
case PHY_INTERFACE_MODE_10GBASER:
|
|
if (mv2222_is_1gbx_capable(phydev)) {
|
|
priv->line_interface = PHY_INTERFACE_MODE_1000BASEX;
|
|
changed = true;
|
|
}
|
|
|
|
if (mv2222_is_sgmii_capable(phydev)) {
|
|
priv->line_interface = PHY_INTERFACE_MODE_SGMII;
|
|
changed = true;
|
|
}
|
|
|
|
break;
|
|
case PHY_INTERFACE_MODE_1000BASEX:
|
|
case PHY_INTERFACE_MODE_SGMII:
|
|
if (mv2222_is_10g_capable(phydev)) {
|
|
priv->line_interface = PHY_INTERFACE_MODE_10GBASER;
|
|
changed = true;
|
|
}
|
|
|
|
break;
|
|
default:
|
|
return -EINVAL;
|
|
}
|
|
|
|
if (changed) {
|
|
ret = mv2222_config_line(phydev);
|
|
if (ret < 0)
|
|
return ret;
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int mv2222_setup_forced(struct phy_device *phydev)
|
|
{
|
|
struct mv2222_data *priv = phydev->priv;
|
|
int ret;
|
|
|
|
if (priv->line_interface == PHY_INTERFACE_MODE_10GBASER) {
|
|
if (phydev->speed < SPEED_10000 &&
|
|
phydev->speed != SPEED_UNKNOWN) {
|
|
ret = mv2222_swap_line_type(phydev);
|
|
if (ret < 0)
|
|
return ret;
|
|
}
|
|
}
|
|
|
|
if (priv->line_interface == PHY_INTERFACE_MODE_SGMII) {
|
|
ret = mv2222_set_sgmii_speed(phydev);
|
|
if (ret < 0)
|
|
return ret;
|
|
}
|
|
|
|
return mv2222_disable_aneg(phydev);
|
|
}
|
|
|
|
static int mv2222_config_aneg(struct phy_device *phydev)
|
|
{
|
|
struct mv2222_data *priv = phydev->priv;
|
|
int ret, adv;
|
|
|
|
/* SFP is not present, do nothing */
|
|
if (priv->line_interface == PHY_INTERFACE_MODE_NA)
|
|
return 0;
|
|
|
|
if (phydev->autoneg == AUTONEG_DISABLE ||
|
|
priv->line_interface == PHY_INTERFACE_MODE_10GBASER)
|
|
return mv2222_setup_forced(phydev);
|
|
|
|
adv = linkmode_adv_to_mii_adv_x(priv->supported,
|
|
ETHTOOL_LINK_MODE_1000baseX_Full_BIT);
|
|
|
|
ret = phy_modify_mmd(phydev, MDIO_MMD_PCS, MV_1GBX_ADVERTISE,
|
|
ADVERTISE_1000XFULL |
|
|
ADVERTISE_1000XPAUSE | ADVERTISE_1000XPSE_ASYM,
|
|
adv);
|
|
if (ret < 0)
|
|
return ret;
|
|
|
|
return mv2222_enable_aneg(phydev);
|
|
}
|
|
|
|
static int mv2222_aneg_done(struct phy_device *phydev)
|
|
{
|
|
int ret;
|
|
|
|
if (mv2222_is_10g_capable(phydev)) {
|
|
ret = phy_read_mmd(phydev, MDIO_MMD_PCS, MDIO_STAT1);
|
|
if (ret < 0)
|
|
return ret;
|
|
|
|
if (ret & MDIO_STAT1_LSTATUS)
|
|
return 1;
|
|
}
|
|
|
|
ret = phy_read_mmd(phydev, MDIO_MMD_PCS, MV_1GBX_STAT);
|
|
if (ret < 0)
|
|
return ret;
|
|
|
|
return (ret & BMSR_ANEGCOMPLETE);
|
|
}
|
|
|
|
/* Returns negative on error, 0 if link is down, 1 if link is up */
|
|
static int mv2222_read_status_10g(struct phy_device *phydev)
|
|
{
|
|
static int timeout;
|
|
int val, link = 0;
|
|
|
|
val = phy_read_mmd(phydev, MDIO_MMD_PCS, MDIO_STAT1);
|
|
if (val < 0)
|
|
return val;
|
|
|
|
if (val & MDIO_STAT1_LSTATUS) {
|
|
link = 1;
|
|
|
|
/* 10GBASE-R do not support auto-negotiation */
|
|
phydev->autoneg = AUTONEG_DISABLE;
|
|
phydev->speed = SPEED_10000;
|
|
phydev->duplex = DUPLEX_FULL;
|
|
} else {
|
|
if (phydev->autoneg == AUTONEG_ENABLE) {
|
|
timeout++;
|
|
|
|
if (timeout > AUTONEG_TIMEOUT) {
|
|
timeout = 0;
|
|
|
|
val = mv2222_swap_line_type(phydev);
|
|
if (val < 0)
|
|
return val;
|
|
|
|
return mv2222_config_aneg(phydev);
|
|
}
|
|
}
|
|
}
|
|
|
|
return link;
|
|
}
|
|
|
|
/* Returns negative on error, 0 if link is down, 1 if link is up */
|
|
static int mv2222_read_status_1g(struct phy_device *phydev)
|
|
{
|
|
static int timeout;
|
|
int val, link = 0;
|
|
|
|
val = phy_read_mmd(phydev, MDIO_MMD_PCS, MV_1GBX_STAT);
|
|
if (val < 0)
|
|
return val;
|
|
|
|
if (phydev->autoneg == AUTONEG_ENABLE &&
|
|
!(val & BMSR_ANEGCOMPLETE)) {
|
|
timeout++;
|
|
|
|
if (timeout > AUTONEG_TIMEOUT) {
|
|
timeout = 0;
|
|
|
|
val = mv2222_swap_line_type(phydev);
|
|
if (val < 0)
|
|
return val;
|
|
|
|
return mv2222_config_aneg(phydev);
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
|
|
if (!(val & BMSR_LSTATUS))
|
|
return 0;
|
|
|
|
link = 1;
|
|
|
|
val = phy_read_mmd(phydev, MDIO_MMD_PCS, MV_1GBX_PHY_STAT);
|
|
if (val < 0)
|
|
return val;
|
|
|
|
if (val & MV_1GBX_PHY_STAT_AN_RESOLVED) {
|
|
if (val & MV_1GBX_PHY_STAT_DUPLEX)
|
|
phydev->duplex = DUPLEX_FULL;
|
|
else
|
|
phydev->duplex = DUPLEX_HALF;
|
|
|
|
if (val & MV_1GBX_PHY_STAT_SPEED1000)
|
|
phydev->speed = SPEED_1000;
|
|
else if (val & MV_1GBX_PHY_STAT_SPEED100)
|
|
phydev->speed = SPEED_100;
|
|
else
|
|
phydev->speed = SPEED_10;
|
|
}
|
|
|
|
return link;
|
|
}
|
|
|
|
static bool mv2222_link_is_operational(struct phy_device *phydev)
|
|
{
|
|
struct mv2222_data *priv = phydev->priv;
|
|
int val;
|
|
|
|
val = phy_read_mmd(phydev, MDIO_MMD_PMAPMD, MV_RX_SIGNAL_DETECT);
|
|
if (val < 0 || !(val & MV_RX_SIGNAL_DETECT_GLOBAL))
|
|
return false;
|
|
|
|
if (phydev->sfp_bus && !priv->sfp_link)
|
|
return false;
|
|
|
|
return true;
|
|
}
|
|
|
|
static int mv2222_read_status(struct phy_device *phydev)
|
|
{
|
|
struct mv2222_data *priv = phydev->priv;
|
|
int link;
|
|
|
|
phydev->link = 0;
|
|
phydev->speed = SPEED_UNKNOWN;
|
|
phydev->duplex = DUPLEX_UNKNOWN;
|
|
|
|
if (!mv2222_link_is_operational(phydev))
|
|
return 0;
|
|
|
|
if (priv->line_interface == PHY_INTERFACE_MODE_10GBASER)
|
|
link = mv2222_read_status_10g(phydev);
|
|
else
|
|
link = mv2222_read_status_1g(phydev);
|
|
|
|
if (link < 0)
|
|
return link;
|
|
|
|
phydev->link = link;
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int mv2222_resume(struct phy_device *phydev)
|
|
{
|
|
return mv2222_tx_enable(phydev);
|
|
}
|
|
|
|
static int mv2222_suspend(struct phy_device *phydev)
|
|
{
|
|
return mv2222_tx_disable(phydev);
|
|
}
|
|
|
|
static int mv2222_get_features(struct phy_device *phydev)
|
|
{
|
|
/* All supported linkmodes are set at probe */
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int mv2222_config_init(struct phy_device *phydev)
|
|
{
|
|
if (phydev->interface != PHY_INTERFACE_MODE_XAUI)
|
|
return -EINVAL;
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int mv2222_sfp_insert(void *upstream, const struct sfp_eeprom_id *id)
|
|
{
|
|
DECLARE_PHY_INTERFACE_MASK(interfaces);
|
|
struct phy_device *phydev = upstream;
|
|
phy_interface_t sfp_interface;
|
|
struct mv2222_data *priv;
|
|
struct device *dev;
|
|
int ret;
|
|
|
|
__ETHTOOL_DECLARE_LINK_MODE_MASK(sfp_supported) = { 0, };
|
|
|
|
priv = phydev->priv;
|
|
dev = &phydev->mdio.dev;
|
|
|
|
sfp_parse_support(phydev->sfp_bus, id, sfp_supported, interfaces);
|
|
phydev->port = sfp_parse_port(phydev->sfp_bus, id, sfp_supported);
|
|
sfp_interface = sfp_select_interface(phydev->sfp_bus, sfp_supported);
|
|
|
|
dev_info(dev, "%s SFP module inserted\n", phy_modes(sfp_interface));
|
|
|
|
if (sfp_interface != PHY_INTERFACE_MODE_10GBASER &&
|
|
sfp_interface != PHY_INTERFACE_MODE_1000BASEX &&
|
|
sfp_interface != PHY_INTERFACE_MODE_SGMII) {
|
|
dev_err(dev, "Incompatible SFP module inserted\n");
|
|
|
|
return -EINVAL;
|
|
}
|
|
|
|
priv->line_interface = sfp_interface;
|
|
linkmode_and(priv->supported, phydev->supported, sfp_supported);
|
|
|
|
ret = mv2222_config_line(phydev);
|
|
if (ret < 0)
|
|
return ret;
|
|
|
|
if (mutex_trylock(&phydev->lock)) {
|
|
ret = mv2222_config_aneg(phydev);
|
|
mutex_unlock(&phydev->lock);
|
|
}
|
|
|
|
return ret;
|
|
}
|
|
|
|
static void mv2222_sfp_remove(void *upstream)
|
|
{
|
|
struct phy_device *phydev = upstream;
|
|
struct mv2222_data *priv;
|
|
|
|
priv = phydev->priv;
|
|
|
|
priv->line_interface = PHY_INTERFACE_MODE_NA;
|
|
linkmode_zero(priv->supported);
|
|
phydev->port = PORT_NONE;
|
|
}
|
|
|
|
static void mv2222_sfp_link_up(void *upstream)
|
|
{
|
|
struct phy_device *phydev = upstream;
|
|
struct mv2222_data *priv;
|
|
|
|
priv = phydev->priv;
|
|
priv->sfp_link = true;
|
|
}
|
|
|
|
static void mv2222_sfp_link_down(void *upstream)
|
|
{
|
|
struct phy_device *phydev = upstream;
|
|
struct mv2222_data *priv;
|
|
|
|
priv = phydev->priv;
|
|
priv->sfp_link = false;
|
|
}
|
|
|
|
static const struct sfp_upstream_ops sfp_phy_ops = {
|
|
.module_insert = mv2222_sfp_insert,
|
|
.module_remove = mv2222_sfp_remove,
|
|
.link_up = mv2222_sfp_link_up,
|
|
.link_down = mv2222_sfp_link_down,
|
|
.attach = phy_sfp_attach,
|
|
.detach = phy_sfp_detach,
|
|
};
|
|
|
|
static int mv2222_probe(struct phy_device *phydev)
|
|
{
|
|
struct device *dev = &phydev->mdio.dev;
|
|
struct mv2222_data *priv = NULL;
|
|
|
|
__ETHTOOL_DECLARE_LINK_MODE_MASK(supported) = { 0, };
|
|
|
|
linkmode_set_bit(ETHTOOL_LINK_MODE_Autoneg_BIT, supported);
|
|
linkmode_set_bit(ETHTOOL_LINK_MODE_Pause_BIT, supported);
|
|
linkmode_set_bit(ETHTOOL_LINK_MODE_Asym_Pause_BIT, supported);
|
|
linkmode_set_bit(ETHTOOL_LINK_MODE_FIBRE_BIT, supported);
|
|
linkmode_set_bit(ETHTOOL_LINK_MODE_TP_BIT, supported);
|
|
linkmode_set_bit(ETHTOOL_LINK_MODE_10baseT_Half_BIT, supported);
|
|
linkmode_set_bit(ETHTOOL_LINK_MODE_10baseT_Full_BIT, supported);
|
|
linkmode_set_bit(ETHTOOL_LINK_MODE_100baseT_Half_BIT, supported);
|
|
linkmode_set_bit(ETHTOOL_LINK_MODE_100baseT_Full_BIT, supported);
|
|
linkmode_set_bit(ETHTOOL_LINK_MODE_1000baseT_Half_BIT, supported);
|
|
linkmode_set_bit(ETHTOOL_LINK_MODE_1000baseT_Full_BIT, supported);
|
|
linkmode_set_bit(ETHTOOL_LINK_MODE_1000baseX_Full_BIT, supported);
|
|
linkmode_set_bit(ETHTOOL_LINK_MODE_10000baseT_Full_BIT, supported);
|
|
linkmode_set_bit(ETHTOOL_LINK_MODE_10000baseCR_Full_BIT, supported);
|
|
linkmode_set_bit(ETHTOOL_LINK_MODE_10000baseSR_Full_BIT, supported);
|
|
linkmode_set_bit(ETHTOOL_LINK_MODE_10000baseLR_Full_BIT, supported);
|
|
linkmode_set_bit(ETHTOOL_LINK_MODE_10000baseLRM_Full_BIT, supported);
|
|
linkmode_set_bit(ETHTOOL_LINK_MODE_10000baseER_Full_BIT, supported);
|
|
|
|
linkmode_copy(phydev->supported, supported);
|
|
|
|
priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
|
|
if (!priv)
|
|
return -ENOMEM;
|
|
|
|
priv->line_interface = PHY_INTERFACE_MODE_NA;
|
|
phydev->priv = priv;
|
|
|
|
return phy_sfp_probe(phydev, &sfp_phy_ops);
|
|
}
|
|
|
|
static struct phy_driver mv2222_drivers[] = {
|
|
{
|
|
.phy_id = MARVELL_PHY_ID_88X2222,
|
|
.phy_id_mask = MARVELL_PHY_ID_MASK,
|
|
.name = "Marvell 88X2222",
|
|
.get_features = mv2222_get_features,
|
|
.soft_reset = mv2222_soft_reset,
|
|
.config_init = mv2222_config_init,
|
|
.config_aneg = mv2222_config_aneg,
|
|
.aneg_done = mv2222_aneg_done,
|
|
.probe = mv2222_probe,
|
|
.suspend = mv2222_suspend,
|
|
.resume = mv2222_resume,
|
|
.read_status = mv2222_read_status,
|
|
},
|
|
};
|
|
module_phy_driver(mv2222_drivers);
|
|
|
|
static struct mdio_device_id __maybe_unused mv2222_tbl[] = {
|
|
{ MARVELL_PHY_ID_88X2222, MARVELL_PHY_ID_MASK },
|
|
{ }
|
|
};
|
|
MODULE_DEVICE_TABLE(mdio, mv2222_tbl);
|
|
|
|
MODULE_DESCRIPTION("Marvell 88x2222 ethernet transceiver driver");
|
|
MODULE_LICENSE("GPL");
|