237 lines
6.2 KiB
C
237 lines
6.2 KiB
C
/* SPDX-License-Identifier: GPL-2.0-or-later */
|
|
/*
|
|
* include/linux/mfd/wm8994/pdata.h -- Platform data for WM8994
|
|
*
|
|
* Copyright 2009 Wolfson Microelectronics PLC.
|
|
*
|
|
* Author: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
*/
|
|
|
|
#ifndef __MFD_WM8994_PDATA_H__
|
|
#define __MFD_WM8994_PDATA_H__
|
|
|
|
#define WM8994_NUM_LDO 2
|
|
#define WM8994_NUM_GPIO 11
|
|
#define WM8994_NUM_AIF 3
|
|
|
|
struct wm8994_ldo_pdata {
|
|
const struct regulator_init_data *init_data;
|
|
};
|
|
|
|
#define WM8994_CONFIGURE_GPIO 0x10000
|
|
|
|
#define WM8994_DRC_REGS 5
|
|
#define WM8994_EQ_REGS 20
|
|
#define WM8958_MBC_CUTOFF_REGS 20
|
|
#define WM8958_MBC_COEFF_REGS 48
|
|
#define WM8958_MBC_COMBINED_REGS 56
|
|
#define WM8958_VSS_HPF_REGS 2
|
|
#define WM8958_VSS_REGS 148
|
|
#define WM8958_ENH_EQ_REGS 32
|
|
|
|
/**
|
|
* DRC configurations are specified with a label and a set of register
|
|
* values to write (the enable bits will be ignored). At runtime an
|
|
* enumerated control will be presented for each DRC block allowing
|
|
* the user to choose the configuration to use.
|
|
*
|
|
* Configurations may be generated by hand or by using the DRC control
|
|
* panel provided by the WISCE - see http://www.wolfsonmicro.com/wisce/
|
|
* for details.
|
|
*/
|
|
struct wm8994_drc_cfg {
|
|
const char *name;
|
|
u16 regs[WM8994_DRC_REGS];
|
|
};
|
|
|
|
/**
|
|
* ReTune Mobile configurations are specified with a label, sample
|
|
* rate and set of values to write (the enable bits will be ignored).
|
|
*
|
|
* Configurations are expected to be generated using the ReTune Mobile
|
|
* control panel in WISCE - see http://www.wolfsonmicro.com/wisce/
|
|
*/
|
|
struct wm8994_retune_mobile_cfg {
|
|
const char *name;
|
|
unsigned int rate;
|
|
u16 regs[WM8994_EQ_REGS];
|
|
};
|
|
|
|
/**
|
|
* Multiband compressor configurations are specified with a label and
|
|
* two sets of values to write. Configurations are expected to be
|
|
* generated using the multiband compressor configuration panel in
|
|
* WISCE - see http://www.wolfsonmicro.com/wisce/
|
|
*/
|
|
struct wm8958_mbc_cfg {
|
|
const char *name;
|
|
u16 cutoff_regs[WM8958_MBC_CUTOFF_REGS];
|
|
u16 coeff_regs[WM8958_MBC_COEFF_REGS];
|
|
|
|
/* Coefficient layout when using MBC+VSS firmware */
|
|
u16 combined_regs[WM8958_MBC_COMBINED_REGS];
|
|
};
|
|
|
|
/**
|
|
* VSS HPF configurations are specified with a label and two values to
|
|
* write. Configurations are expected to be generated using the
|
|
* multiband compressor configuration panel in WISCE - see
|
|
* http://www.wolfsonmicro.com/wisce/
|
|
*/
|
|
struct wm8958_vss_hpf_cfg {
|
|
const char *name;
|
|
u16 regs[WM8958_VSS_HPF_REGS];
|
|
};
|
|
|
|
/**
|
|
* VSS configurations are specified with a label and array of values
|
|
* to write. Configurations are expected to be generated using the
|
|
* multiband compressor configuration panel in WISCE - see
|
|
* http://www.wolfsonmicro.com/wisce/
|
|
*/
|
|
struct wm8958_vss_cfg {
|
|
const char *name;
|
|
u16 regs[WM8958_VSS_REGS];
|
|
};
|
|
|
|
/**
|
|
* Enhanced EQ configurations are specified with a label and array of
|
|
* values to write. Configurations are expected to be generated using
|
|
* the multiband compressor configuration panel in WISCE - see
|
|
* http://www.wolfsonmicro.com/wisce/
|
|
*/
|
|
struct wm8958_enh_eq_cfg {
|
|
const char *name;
|
|
u16 regs[WM8958_ENH_EQ_REGS];
|
|
};
|
|
|
|
/**
|
|
* Microphone detection rates, used to tune response rates and power
|
|
* consumption for WM8958/WM1811 microphone detection.
|
|
*
|
|
* @sysclk: System clock rate to use this configuration for.
|
|
* @idle: True if this configuration should use when no accessory is detected,
|
|
* false otherwise.
|
|
* @start: Value for MICD_BIAS_START_TIME register field (not shifted).
|
|
* @rate: Value for MICD_RATE register field (not shifted).
|
|
*/
|
|
struct wm8958_micd_rate {
|
|
int sysclk;
|
|
bool idle;
|
|
int start;
|
|
int rate;
|
|
};
|
|
|
|
struct wm8994_pdata {
|
|
int gpio_base;
|
|
|
|
/**
|
|
* Default values for GPIOs if non-zero, WM8994_CONFIGURE_GPIO
|
|
* can be used for all zero values.
|
|
*/
|
|
int gpio_defaults[WM8994_NUM_GPIO];
|
|
|
|
struct wm8994_ldo_pdata ldo[WM8994_NUM_LDO];
|
|
|
|
int irq_base; /** Base IRQ number for WM8994, required for IRQs */
|
|
unsigned long irq_flags; /** user irq flags */
|
|
|
|
int num_drc_cfgs;
|
|
struct wm8994_drc_cfg *drc_cfgs;
|
|
|
|
int num_retune_mobile_cfgs;
|
|
struct wm8994_retune_mobile_cfg *retune_mobile_cfgs;
|
|
|
|
int num_mbc_cfgs;
|
|
struct wm8958_mbc_cfg *mbc_cfgs;
|
|
|
|
int num_vss_cfgs;
|
|
struct wm8958_vss_cfg *vss_cfgs;
|
|
|
|
int num_vss_hpf_cfgs;
|
|
struct wm8958_vss_hpf_cfg *vss_hpf_cfgs;
|
|
|
|
int num_enh_eq_cfgs;
|
|
struct wm8958_enh_eq_cfg *enh_eq_cfgs;
|
|
|
|
int num_micd_rates;
|
|
struct wm8958_micd_rate *micd_rates;
|
|
|
|
/* Power up delays to add after microphone bias power up (ms) */
|
|
int micb1_delay;
|
|
int micb2_delay;
|
|
|
|
/* LINEOUT can be differential or single ended */
|
|
unsigned int lineout1_diff:1;
|
|
unsigned int lineout2_diff:1;
|
|
|
|
/* Common mode feedback */
|
|
unsigned int lineout1fb:1;
|
|
unsigned int lineout2fb:1;
|
|
|
|
/* Delay between detecting a jack and starting microphone
|
|
* detect (specified in ms)
|
|
*/
|
|
int micdet_delay;
|
|
|
|
/* Delay between microphone detect completing and reporting on
|
|
* insert (specified in ms)
|
|
*/
|
|
int mic_id_delay;
|
|
|
|
/* IRQ for microphone detection if brought out directly as a
|
|
* signal.
|
|
*/
|
|
int micdet_irq;
|
|
|
|
/* WM8994 microphone biases: 0=0.9*AVDD1 1=0.65*AVVD1 */
|
|
unsigned int micbias1_lvl:1;
|
|
unsigned int micbias2_lvl:1;
|
|
|
|
/* WM8994 jack detect threashold levels, see datasheet for values */
|
|
unsigned int jd_scthr:2;
|
|
unsigned int jd_thr:2;
|
|
|
|
/* Configure WM1811 jack detection for use with external capacitor */
|
|
unsigned int jd_ext_cap:1;
|
|
|
|
/* WM8958 microphone bias configuration */
|
|
int micbias[2];
|
|
|
|
/* WM8958 microphone detection ranges */
|
|
u16 micd_lvl_sel;
|
|
|
|
/* Disable the internal pull downs on the LDOs if they are
|
|
* always driven (eg, connected to an always on supply or
|
|
* GPIO that always drives an output. If they float power
|
|
* consumption will rise.
|
|
*/
|
|
bool ldo_ena_always_driven;
|
|
|
|
/*
|
|
* SPKMODE must be pulled internally by the device on this
|
|
* system.
|
|
*/
|
|
bool spkmode_pu;
|
|
|
|
/*
|
|
* CS/ADDR must be pulled internally by the device on this
|
|
* system.
|
|
*/
|
|
bool csnaddr_pd;
|
|
|
|
/**
|
|
* Maximum number of channels clocks will be generated for,
|
|
* useful for systems where and I2S bus with multiple data
|
|
* lines is mastered.
|
|
*/
|
|
int max_channels_clocked[WM8994_NUM_AIF];
|
|
|
|
/**
|
|
* GPIO for the IRQ pin if host only supports edge triggering
|
|
*/
|
|
int irq_gpio;
|
|
};
|
|
|
|
#endif
|