762 lines
29 KiB
C
762 lines
29 KiB
C
#ifndef NETDEV_PCS_H
|
|
#define NETDEV_PCS_H
|
|
|
|
#include <linux/phy.h>
|
|
#include <linux/spinlock.h>
|
|
#include <linux/workqueue.h>
|
|
|
|
struct device_node;
|
|
struct ethtool_cmd;
|
|
struct fwnode_handle;
|
|
struct net_device;
|
|
|
|
enum {
|
|
MLO_PAUSE_NONE,
|
|
MLO_PAUSE_RX = BIT(0),
|
|
MLO_PAUSE_TX = BIT(1),
|
|
MLO_PAUSE_TXRX_MASK = MLO_PAUSE_TX | MLO_PAUSE_RX,
|
|
MLO_PAUSE_AN = BIT(2),
|
|
|
|
MLO_AN_PHY = 0, /* Conventional PHY */
|
|
MLO_AN_FIXED, /* Fixed-link mode */
|
|
MLO_AN_INBAND, /* In-band protocol */
|
|
|
|
/* PCS "negotiation" mode.
|
|
* PHYLINK_PCS_NEG_NONE - protocol has no inband capability
|
|
* PHYLINK_PCS_NEG_OUTBAND - some out of band or fixed link setting
|
|
* PHYLINK_PCS_NEG_INBAND_DISABLED - inband mode disabled, e.g.
|
|
* 1000base-X with autoneg off
|
|
* PHYLINK_PCS_NEG_INBAND_ENABLED - inband mode enabled
|
|
* Additionally, this can be tested using bitmasks:
|
|
* PHYLINK_PCS_NEG_INBAND - inband mode selected
|
|
* PHYLINK_PCS_NEG_ENABLED - negotiation mode enabled
|
|
*/
|
|
PHYLINK_PCS_NEG_NONE = 0,
|
|
PHYLINK_PCS_NEG_ENABLED = BIT(4),
|
|
PHYLINK_PCS_NEG_OUTBAND = BIT(5),
|
|
PHYLINK_PCS_NEG_INBAND = BIT(6),
|
|
PHYLINK_PCS_NEG_INBAND_DISABLED = PHYLINK_PCS_NEG_INBAND,
|
|
PHYLINK_PCS_NEG_INBAND_ENABLED = PHYLINK_PCS_NEG_INBAND |
|
|
PHYLINK_PCS_NEG_ENABLED,
|
|
|
|
/* MAC_SYM_PAUSE and MAC_ASYM_PAUSE are used when configuring our
|
|
* autonegotiation advertisement. They correspond to the PAUSE and
|
|
* ASM_DIR bits defined by 802.3, respectively.
|
|
*
|
|
* The following table lists the values of tx_pause and rx_pause which
|
|
* might be requested in mac_link_up. The exact values depend on either
|
|
* the results of autonegotation (if MLO_PAUSE_AN is set) or user
|
|
* configuration (if MLO_PAUSE_AN is not set).
|
|
*
|
|
* MAC_SYM_PAUSE MAC_ASYM_PAUSE MLO_PAUSE_AN tx_pause/rx_pause
|
|
* ============= ============== ============ ==================
|
|
* 0 0 0 0/0
|
|
* 0 0 1 0/0
|
|
* 0 1 0 0/0, 0/1, 1/0, 1/1
|
|
* 0 1 1 0/0, 1/0
|
|
* 1 0 0 0/0, 1/1
|
|
* 1 0 1 0/0, 1/1
|
|
* 1 1 0 0/0, 0/1, 1/0, 1/1
|
|
* 1 1 1 0/0, 0/1, 1/1
|
|
*
|
|
* If you set MAC_ASYM_PAUSE, the user may request any combination of
|
|
* tx_pause and rx_pause. You do not have to support these
|
|
* combinations.
|
|
*
|
|
* However, you should support combinations of tx_pause and rx_pause
|
|
* which might be the result of autonegotation. For example, don't set
|
|
* MAC_SYM_PAUSE unless your device can support tx_pause and rx_pause
|
|
* at the same time.
|
|
*/
|
|
MAC_SYM_PAUSE = BIT(0),
|
|
MAC_ASYM_PAUSE = BIT(1),
|
|
MAC_10HD = BIT(2),
|
|
MAC_10FD = BIT(3),
|
|
MAC_10 = MAC_10HD | MAC_10FD,
|
|
MAC_100HD = BIT(4),
|
|
MAC_100FD = BIT(5),
|
|
MAC_100 = MAC_100HD | MAC_100FD,
|
|
MAC_1000HD = BIT(6),
|
|
MAC_1000FD = BIT(7),
|
|
MAC_1000 = MAC_1000HD | MAC_1000FD,
|
|
MAC_2500FD = BIT(8),
|
|
MAC_5000FD = BIT(9),
|
|
MAC_10000FD = BIT(10),
|
|
MAC_20000FD = BIT(11),
|
|
MAC_25000FD = BIT(12),
|
|
MAC_40000FD = BIT(13),
|
|
MAC_50000FD = BIT(14),
|
|
MAC_56000FD = BIT(15),
|
|
MAC_100000FD = BIT(16),
|
|
MAC_200000FD = BIT(17),
|
|
MAC_400000FD = BIT(18),
|
|
};
|
|
|
|
static inline bool phylink_autoneg_inband(unsigned int mode)
|
|
{
|
|
return mode == MLO_AN_INBAND;
|
|
}
|
|
|
|
/**
|
|
* phylink_pcs_neg_mode() - helper to determine PCS inband mode
|
|
* @mode: one of %MLO_AN_FIXED, %MLO_AN_PHY, %MLO_AN_INBAND.
|
|
* @interface: interface mode to be used
|
|
* @advertising: adertisement ethtool link mode mask
|
|
*
|
|
* Determines the negotiation mode to be used by the PCS, and returns
|
|
* one of:
|
|
*
|
|
* - %PHYLINK_PCS_NEG_NONE: interface mode does not support inband
|
|
* - %PHYLINK_PCS_NEG_OUTBAND: an out of band mode (e.g. reading the PHY)
|
|
* will be used.
|
|
* - %PHYLINK_PCS_NEG_INBAND_DISABLED: inband mode selected but autoneg
|
|
* disabled
|
|
* - %PHYLINK_PCS_NEG_INBAND_ENABLED: inband mode selected and autoneg enabled
|
|
*
|
|
* Note: this is for cases where the PCS itself is involved in negotiation
|
|
* (e.g. Clause 37, SGMII and similar) not Clause 73.
|
|
*/
|
|
static inline unsigned int phylink_pcs_neg_mode(unsigned int mode,
|
|
phy_interface_t interface,
|
|
const unsigned long *advertising)
|
|
{
|
|
unsigned int neg_mode;
|
|
|
|
switch (interface) {
|
|
case PHY_INTERFACE_MODE_SGMII:
|
|
case PHY_INTERFACE_MODE_QSGMII:
|
|
case PHY_INTERFACE_MODE_QUSGMII:
|
|
case PHY_INTERFACE_MODE_USXGMII:
|
|
/* These protocols are designed for use with a PHY which
|
|
* communicates its negotiation result back to the MAC via
|
|
* inband communication. Note: there exist PHYs that run
|
|
* with SGMII but do not send the inband data.
|
|
*/
|
|
if (!phylink_autoneg_inband(mode))
|
|
neg_mode = PHYLINK_PCS_NEG_OUTBAND;
|
|
else
|
|
neg_mode = PHYLINK_PCS_NEG_INBAND_ENABLED;
|
|
break;
|
|
|
|
case PHY_INTERFACE_MODE_1000BASEX:
|
|
case PHY_INTERFACE_MODE_2500BASEX:
|
|
/* 1000base-X is designed for use media-side for Fibre
|
|
* connections, and thus the Autoneg bit needs to be
|
|
* taken into account. We also do this for 2500base-X
|
|
* as well, but drivers may not support this, so may
|
|
* need to override this.
|
|
*/
|
|
if (!phylink_autoneg_inband(mode))
|
|
neg_mode = PHYLINK_PCS_NEG_OUTBAND;
|
|
else if (linkmode_test_bit(ETHTOOL_LINK_MODE_Autoneg_BIT,
|
|
advertising))
|
|
neg_mode = PHYLINK_PCS_NEG_INBAND_ENABLED;
|
|
else
|
|
neg_mode = PHYLINK_PCS_NEG_INBAND_DISABLED;
|
|
break;
|
|
|
|
default:
|
|
neg_mode = PHYLINK_PCS_NEG_NONE;
|
|
break;
|
|
}
|
|
|
|
return neg_mode;
|
|
}
|
|
|
|
/**
|
|
* struct phylink_link_state - link state structure
|
|
* @advertising: ethtool bitmask containing advertised link modes
|
|
* @lp_advertising: ethtool bitmask containing link partner advertised link
|
|
* modes
|
|
* @interface: link &typedef phy_interface_t mode
|
|
* @speed: link speed, one of the SPEED_* constants.
|
|
* @duplex: link duplex mode, one of DUPLEX_* constants.
|
|
* @pause: link pause state, described by MLO_PAUSE_* constants.
|
|
* @rate_matching: rate matching being performed, one of the RATE_MATCH_*
|
|
* constants. If rate matching is taking place, then the speed/duplex of
|
|
* the medium link mode (@speed and @duplex) and the speed/duplex of the phy
|
|
* interface mode (@interface) are different.
|
|
* @link: true if the link is up.
|
|
* @an_complete: true if autonegotiation has completed.
|
|
*/
|
|
struct phylink_link_state {
|
|
__ETHTOOL_DECLARE_LINK_MODE_MASK(advertising);
|
|
__ETHTOOL_DECLARE_LINK_MODE_MASK(lp_advertising);
|
|
phy_interface_t interface;
|
|
int speed;
|
|
int duplex;
|
|
int pause;
|
|
int rate_matching;
|
|
unsigned int link:1;
|
|
unsigned int an_complete:1;
|
|
};
|
|
|
|
enum phylink_op_type {
|
|
PHYLINK_NETDEV = 0,
|
|
PHYLINK_DEV,
|
|
};
|
|
|
|
/**
|
|
* struct phylink_config - PHYLINK configuration structure
|
|
* @dev: a pointer to a struct device associated with the MAC
|
|
* @type: operation type of PHYLINK instance
|
|
* @legacy_pre_march2020: driver has not been updated for March 2020 updates
|
|
* (See commit 7cceb599d15d ("net: phylink: avoid mac_config calls")
|
|
* @poll_fixed_state: if true, starts link_poll,
|
|
* if MAC link is at %MLO_AN_FIXED mode.
|
|
* @mac_managed_pm: if true, indicate the MAC driver is responsible for PHY PM.
|
|
* @ovr_an_inband: if true, override PCS to MLO_AN_INBAND
|
|
* @get_fixed_state: callback to execute to determine the fixed link state,
|
|
* if MAC link is at %MLO_AN_FIXED mode.
|
|
* @supported_interfaces: bitmap describing which PHY_INTERFACE_MODE_xxx
|
|
* are supported by the MAC/PCS.
|
|
* @mac_capabilities: MAC pause/speed/duplex capabilities.
|
|
*/
|
|
struct phylink_config {
|
|
struct device *dev;
|
|
enum phylink_op_type type;
|
|
bool legacy_pre_march2020;
|
|
bool poll_fixed_state;
|
|
bool mac_managed_pm;
|
|
bool ovr_an_inband;
|
|
void (*get_fixed_state)(struct phylink_config *config,
|
|
struct phylink_link_state *state);
|
|
DECLARE_PHY_INTERFACE_MASK(supported_interfaces);
|
|
unsigned long mac_capabilities;
|
|
};
|
|
|
|
/**
|
|
* struct phylink_mac_ops - MAC operations structure.
|
|
* @validate: Validate and update the link configuration.
|
|
* @mac_select_pcs: Select a PCS for the interface mode.
|
|
* @mac_pcs_get_state: Read the current link state from the hardware.
|
|
* @mac_prepare: prepare for a major reconfiguration of the interface.
|
|
* @mac_config: configure the MAC for the selected mode and state.
|
|
* @mac_finish: finish a major reconfiguration of the interface.
|
|
* @mac_an_restart: restart 802.3z BaseX autonegotiation.
|
|
* @mac_link_down: take the link down.
|
|
* @mac_link_up: allow the link to come up.
|
|
*
|
|
* The individual methods are described more fully below.
|
|
*/
|
|
struct phylink_mac_ops {
|
|
void (*validate)(struct phylink_config *config,
|
|
unsigned long *supported,
|
|
struct phylink_link_state *state);
|
|
struct phylink_pcs *(*mac_select_pcs)(struct phylink_config *config,
|
|
phy_interface_t interface);
|
|
void (*mac_pcs_get_state)(struct phylink_config *config,
|
|
struct phylink_link_state *state);
|
|
int (*mac_prepare)(struct phylink_config *config, unsigned int mode,
|
|
phy_interface_t iface);
|
|
void (*mac_config)(struct phylink_config *config, unsigned int mode,
|
|
const struct phylink_link_state *state);
|
|
int (*mac_finish)(struct phylink_config *config, unsigned int mode,
|
|
phy_interface_t iface);
|
|
void (*mac_an_restart)(struct phylink_config *config);
|
|
void (*mac_link_down)(struct phylink_config *config, unsigned int mode,
|
|
phy_interface_t interface);
|
|
void (*mac_link_up)(struct phylink_config *config,
|
|
struct phy_device *phy, unsigned int mode,
|
|
phy_interface_t interface, int speed, int duplex,
|
|
bool tx_pause, bool rx_pause);
|
|
};
|
|
|
|
#if 0 /* For kernel-doc purposes only. */
|
|
/**
|
|
* validate - Validate and update the link configuration
|
|
* @config: a pointer to a &struct phylink_config.
|
|
* @supported: ethtool bitmask for supported link modes.
|
|
* @state: a pointer to a &struct phylink_link_state.
|
|
*
|
|
* Clear bits in the @supported and @state->advertising masks that
|
|
* are not supportable by the MAC.
|
|
*
|
|
* Note that the PHY may be able to transform from one connection
|
|
* technology to another, so, eg, don't clear 1000BaseX just
|
|
* because the MAC is unable to BaseX mode. This is more about
|
|
* clearing unsupported speeds and duplex settings. The port modes
|
|
* should not be cleared; phylink_set_port_modes() will help with this.
|
|
*
|
|
* When @config->supported_interfaces has been set, phylink will iterate
|
|
* over the supported interfaces to determine the full capability of the
|
|
* MAC. The validation function must not print errors if @state->interface
|
|
* is set to an unexpected value.
|
|
*
|
|
* When @config->supported_interfaces is empty, phylink will call this
|
|
* function with @state->interface set to %PHY_INTERFACE_MODE_NA, and
|
|
* expects the MAC driver to return all supported link modes.
|
|
*
|
|
* If the @state->interface mode is not supported, then the @supported
|
|
* mask must be cleared.
|
|
*
|
|
* This member is optional; if not set, the generic validator will be
|
|
* used making use of @config->mac_capabilities and
|
|
* @config->supported_interfaces to determine which link modes are
|
|
* supported.
|
|
*/
|
|
void validate(struct phylink_config *config, unsigned long *supported,
|
|
struct phylink_link_state *state);
|
|
/**
|
|
* mac_select_pcs: Select a PCS for the interface mode.
|
|
* @config: a pointer to a &struct phylink_config.
|
|
* @interface: PHY interface mode for PCS
|
|
*
|
|
* Return the &struct phylink_pcs for the specified interface mode, or
|
|
* NULL if none is required, or an error pointer on error.
|
|
*
|
|
* This must not modify any state. It is used to query which PCS should
|
|
* be used. Phylink will use this during validation to ensure that the
|
|
* configuration is valid, and when setting a configuration to internally
|
|
* set the PCS that will be used.
|
|
*/
|
|
struct phylink_pcs *mac_select_pcs(struct phylink_config *config,
|
|
phy_interface_t interface);
|
|
|
|
/**
|
|
* mac_pcs_get_state() - Read the current inband link state from the hardware
|
|
* @config: a pointer to a &struct phylink_config.
|
|
* @state: a pointer to a &struct phylink_link_state.
|
|
*
|
|
* Read the current inband link state from the MAC PCS, reporting the
|
|
* current speed in @state->speed, duplex mode in @state->duplex, pause
|
|
* mode in @state->pause using the %MLO_PAUSE_RX and %MLO_PAUSE_TX bits,
|
|
* negotiation completion state in @state->an_complete, and link up state
|
|
* in @state->link. If possible, @state->lp_advertising should also be
|
|
* populated.
|
|
*
|
|
* Note: This is a legacy method. This function will not be called unless
|
|
* legacy_pre_march2020 is set in &struct phylink_config and there is no
|
|
* PCS attached.
|
|
*/
|
|
void mac_pcs_get_state(struct phylink_config *config,
|
|
struct phylink_link_state *state);
|
|
|
|
/**
|
|
* mac_prepare() - prepare to change the PHY interface mode
|
|
* @config: a pointer to a &struct phylink_config.
|
|
* @mode: one of %MLO_AN_FIXED, %MLO_AN_PHY, %MLO_AN_INBAND.
|
|
* @iface: interface mode to switch to
|
|
*
|
|
* phylink will call this method at the beginning of a full initialisation
|
|
* of the link, which includes changing the interface mode or at initial
|
|
* startup time. It may be called for the current mode. The MAC driver
|
|
* should perform whatever actions are required, e.g. disabling the
|
|
* Serdes PHY.
|
|
*
|
|
* This will be the first call in the sequence:
|
|
* - mac_prepare()
|
|
* - mac_config()
|
|
* - pcs_config()
|
|
* - possible pcs_an_restart()
|
|
* - mac_finish()
|
|
*
|
|
* Returns zero on success, or negative errno on failure which will be
|
|
* reported to the kernel log.
|
|
*/
|
|
int mac_prepare(struct phylink_config *config, unsigned int mode,
|
|
phy_interface_t iface);
|
|
|
|
/**
|
|
* mac_config() - configure the MAC for the selected mode and state
|
|
* @config: a pointer to a &struct phylink_config.
|
|
* @mode: one of %MLO_AN_FIXED, %MLO_AN_PHY, %MLO_AN_INBAND.
|
|
* @state: a pointer to a &struct phylink_link_state.
|
|
*
|
|
* Note - not all members of @state are valid. In particular,
|
|
* @state->lp_advertising, @state->link, @state->an_complete are never
|
|
* guaranteed to be correct, and so any mac_config() implementation must
|
|
* never reference these fields.
|
|
*
|
|
* Note: For legacy March 2020 drivers (drivers with legacy_pre_march2020 set
|
|
* in their &phylnk_config and which don't have a PCS), this function will be
|
|
* called on each link up event, and to also change the in-band advert. For
|
|
* non-legacy drivers, it will only be called to reconfigure the MAC for a
|
|
* "major" change in e.g. interface mode. It will not be called for changes
|
|
* in speed, duplex or pause modes or to change the in-band advertisement.
|
|
* In any case, it is strongly preferred that speed, duplex and pause settings
|
|
* are handled in the mac_link_up() method and not in this method.
|
|
*
|
|
* (this requires a rewrite - please refer to mac_link_up() for situations
|
|
* where the PCS and MAC are not tightly integrated.)
|
|
*
|
|
* In all negotiation modes, as defined by @mode, @state->pause indicates the
|
|
* pause settings which should be applied as follows. If %MLO_PAUSE_AN is not
|
|
* set, %MLO_PAUSE_TX and %MLO_PAUSE_RX indicate whether the MAC should send
|
|
* pause frames and/or act on received pause frames respectively. Otherwise,
|
|
* the results of in-band negotiation/status from the MAC PCS should be used
|
|
* to control the MAC pause mode settings.
|
|
*
|
|
* The action performed depends on the currently selected mode:
|
|
*
|
|
* %MLO_AN_FIXED, %MLO_AN_PHY:
|
|
* Configure for non-inband negotiation mode, where the link settings
|
|
* are completely communicated via mac_link_up(). The physical link
|
|
* protocol from the MAC is specified by @state->interface.
|
|
*
|
|
* @state->advertising may be used, but is not required.
|
|
*
|
|
* Older drivers (prior to the mac_link_up() change) may use @state->speed,
|
|
* @state->duplex and @state->pause to configure the MAC, but this is
|
|
* deprecated; such drivers should be converted to use mac_link_up().
|
|
*
|
|
* Other members of @state must be ignored.
|
|
*
|
|
* Valid state members: interface, advertising.
|
|
* Deprecated state members: speed, duplex, pause.
|
|
*
|
|
* %MLO_AN_INBAND:
|
|
* place the link in an inband negotiation mode (such as 802.3z
|
|
* 1000base-X or Cisco SGMII mode depending on the @state->interface
|
|
* mode). In both cases, link state management (whether the link
|
|
* is up or not) is performed by the MAC, and reported via the
|
|
* mac_pcs_get_state() callback. Changes in link state must be made
|
|
* by calling phylink_mac_change().
|
|
*
|
|
* Interface mode specific details are mentioned below.
|
|
*
|
|
* If in 802.3z mode, the link speed is fixed, dependent on the
|
|
* @state->interface. Duplex and pause modes are negotiated via
|
|
* the in-band configuration word. Advertised pause modes are set
|
|
* according to the @state->an_enabled and @state->advertising
|
|
* flags. Beware of MACs which only support full duplex at gigabit
|
|
* and higher speeds.
|
|
*
|
|
* If in Cisco SGMII mode, the link speed and duplex mode are passed
|
|
* in the serial bitstream 16-bit configuration word, and the MAC
|
|
* should be configured to read these bits and acknowledge the
|
|
* configuration word. Nothing is advertised by the MAC. The MAC is
|
|
* responsible for reading the configuration word and configuring
|
|
* itself accordingly.
|
|
*
|
|
* Valid state members: interface, an_enabled, pause, advertising.
|
|
*
|
|
* Implementations are expected to update the MAC to reflect the
|
|
* requested settings - i.o.w., if nothing has changed between two
|
|
* calls, no action is expected. If only flow control settings have
|
|
* changed, flow control should be updated *without* taking the link
|
|
* down. This "update" behaviour is critical to avoid bouncing the
|
|
* link up status.
|
|
*/
|
|
void mac_config(struct phylink_config *config, unsigned int mode,
|
|
const struct phylink_link_state *state);
|
|
|
|
/**
|
|
* mac_finish() - finish a to change the PHY interface mode
|
|
* @config: a pointer to a &struct phylink_config.
|
|
* @mode: one of %MLO_AN_FIXED, %MLO_AN_PHY, %MLO_AN_INBAND.
|
|
* @iface: interface mode to switch to
|
|
*
|
|
* phylink will call this if it called mac_prepare() to allow the MAC to
|
|
* complete any necessary steps after the MAC and PCS have been configured
|
|
* for the @mode and @iface. E.g. a MAC driver may wish to re-enable the
|
|
* Serdes PHY here if it was previously disabled by mac_prepare().
|
|
*
|
|
* Returns zero on success, or negative errno on failure which will be
|
|
* reported to the kernel log.
|
|
*/
|
|
int mac_finish(struct phylink_config *config, unsigned int mode,
|
|
phy_interface_t iface);
|
|
|
|
/**
|
|
* mac_an_restart() - restart 802.3z BaseX autonegotiation
|
|
* @config: a pointer to a &struct phylink_config.
|
|
*
|
|
* Note: This is a legacy method. This function will not be called unless
|
|
* legacy_pre_march2020 is set in &struct phylink_config and there is no
|
|
* PCS attached.
|
|
*/
|
|
void mac_an_restart(struct phylink_config *config);
|
|
|
|
/**
|
|
* mac_link_down() - take the link down
|
|
* @config: a pointer to a &struct phylink_config.
|
|
* @mode: link autonegotiation mode
|
|
* @interface: link &typedef phy_interface_t mode
|
|
*
|
|
* If @mode is not an in-band negotiation mode (as defined by
|
|
* phylink_autoneg_inband()), force the link down and disable any
|
|
* Energy Efficient Ethernet MAC configuration. Interface type
|
|
* selection must be done in mac_config().
|
|
*/
|
|
void mac_link_down(struct phylink_config *config, unsigned int mode,
|
|
phy_interface_t interface);
|
|
|
|
/**
|
|
* mac_link_up() - allow the link to come up
|
|
* @config: a pointer to a &struct phylink_config.
|
|
* @phy: any attached phy
|
|
* @mode: link autonegotiation mode
|
|
* @interface: link &typedef phy_interface_t mode
|
|
* @speed: link speed
|
|
* @duplex: link duplex
|
|
* @tx_pause: link transmit pause enablement status
|
|
* @rx_pause: link receive pause enablement status
|
|
*
|
|
* Configure the MAC for an established link.
|
|
*
|
|
* @speed, @duplex, @tx_pause and @rx_pause indicate the finalised link
|
|
* settings, and should be used to configure the MAC block appropriately
|
|
* where these settings are not automatically conveyed from the PCS block,
|
|
* or if in-band negotiation (as defined by phylink_autoneg_inband(@mode))
|
|
* is disabled.
|
|
*
|
|
* Note that when 802.3z in-band negotiation is in use, it is possible
|
|
* that the user wishes to override the pause settings, and this should
|
|
* be allowed when considering the implementation of this method.
|
|
*
|
|
* If in-band negotiation mode is disabled, allow the link to come up. If
|
|
* @phy is non-%NULL, configure Energy Efficient Ethernet by calling
|
|
* phy_init_eee() and perform appropriate MAC configuration for EEE.
|
|
* Interface type selection must be done in mac_config().
|
|
*/
|
|
void mac_link_up(struct phylink_config *config, struct phy_device *phy,
|
|
unsigned int mode, phy_interface_t interface,
|
|
int speed, int duplex, bool tx_pause, bool rx_pause);
|
|
#endif
|
|
|
|
struct phylink_pcs_ops;
|
|
|
|
/**
|
|
* struct phylink_pcs - PHYLINK PCS instance
|
|
* @ops: a pointer to the &struct phylink_pcs_ops structure
|
|
* @neg_mode: provide PCS neg mode via "mode" argument
|
|
* @poll: poll the PCS for link changes
|
|
*
|
|
* This structure is designed to be embedded within the PCS private data,
|
|
* and will be passed between phylink and the PCS.
|
|
*/
|
|
struct phylink_pcs {
|
|
const struct phylink_pcs_ops *ops;
|
|
bool neg_mode;
|
|
bool poll;
|
|
};
|
|
|
|
/**
|
|
* struct phylink_pcs_ops - MAC PCS operations structure.
|
|
* @pcs_validate: validate the link configuration.
|
|
* @pcs_get_state: read the current MAC PCS link state from the hardware.
|
|
* @pcs_config: configure the MAC PCS for the selected mode and state.
|
|
* @pcs_an_restart: restart 802.3z BaseX autonegotiation.
|
|
* @pcs_link_up: program the PCS for the resolved link configuration
|
|
* (where necessary).
|
|
*/
|
|
struct phylink_pcs_ops {
|
|
int (*pcs_validate)(struct phylink_pcs *pcs, unsigned long *supported,
|
|
const struct phylink_link_state *state);
|
|
void (*pcs_get_state)(struct phylink_pcs *pcs,
|
|
struct phylink_link_state *state);
|
|
int (*pcs_config)(struct phylink_pcs *pcs, unsigned int neg_mode,
|
|
phy_interface_t interface,
|
|
const unsigned long *advertising,
|
|
bool permit_pause_to_mac);
|
|
void (*pcs_an_restart)(struct phylink_pcs *pcs);
|
|
void (*pcs_link_up)(struct phylink_pcs *pcs, unsigned int neg_mode,
|
|
phy_interface_t interface, int speed, int duplex);
|
|
};
|
|
|
|
#if 0 /* For kernel-doc purposes only. */
|
|
/**
|
|
* pcs_validate() - validate the link configuration.
|
|
* @pcs: a pointer to a &struct phylink_pcs.
|
|
* @supported: ethtool bitmask for supported link modes.
|
|
* @state: a const pointer to a &struct phylink_link_state.
|
|
*
|
|
* Validate the interface mode, and advertising's autoneg bit, removing any
|
|
* media ethtool link modes that would not be supportable from the supported
|
|
* mask. Phylink will propagate the changes to the advertising mask. See the
|
|
* &struct phylink_mac_ops validate() method.
|
|
*
|
|
* Returns -EINVAL if the interface mode/autoneg mode is not supported.
|
|
* Returns non-zero positive if the link state can be supported.
|
|
*/
|
|
int pcs_validate(struct phylink_pcs *pcs, unsigned long *supported,
|
|
const struct phylink_link_state *state);
|
|
|
|
/**
|
|
* pcs_get_state() - Read the current inband link state from the hardware
|
|
* @pcs: a pointer to a &struct phylink_pcs.
|
|
* @state: a pointer to a &struct phylink_link_state.
|
|
*
|
|
* Read the current inband link state from the MAC PCS, reporting the
|
|
* current speed in @state->speed, duplex mode in @state->duplex, pause
|
|
* mode in @state->pause using the %MLO_PAUSE_RX and %MLO_PAUSE_TX bits,
|
|
* negotiation completion state in @state->an_complete, and link up state
|
|
* in @state->link. If possible, @state->lp_advertising should also be
|
|
* populated.
|
|
*
|
|
* When present, this overrides mac_pcs_get_state() in &struct
|
|
* phylink_mac_ops.
|
|
*/
|
|
void pcs_get_state(struct phylink_pcs *pcs,
|
|
struct phylink_link_state *state);
|
|
|
|
/**
|
|
* pcs_config() - Configure the PCS mode and advertisement
|
|
* @pcs: a pointer to a &struct phylink_pcs.
|
|
* @neg_mode: link negotiation mode (see below)
|
|
* @interface: interface mode to be used
|
|
* @advertising: adertisement ethtool link mode mask
|
|
* @permit_pause_to_mac: permit forwarding pause resolution to MAC
|
|
*
|
|
* Configure the PCS for the operating mode, the interface mode, and set
|
|
* the advertisement mask. @permit_pause_to_mac indicates whether the
|
|
* hardware may forward the pause mode resolution to the MAC.
|
|
*
|
|
* When operating in %MLO_AN_INBAND, inband should always be enabled,
|
|
* otherwise inband should be disabled.
|
|
*
|
|
* For SGMII, there is no advertisement from the MAC side, the PCS should
|
|
* be programmed to acknowledge the inband word from the PHY.
|
|
*
|
|
* For 1000BASE-X, the advertisement should be programmed into the PCS.
|
|
*
|
|
* For most 10GBASE-R, there is no advertisement.
|
|
*
|
|
* The %neg_mode argument should be tested via the phylink_mode_*() family of
|
|
* functions, or for PCS that set pcs->neg_mode true, should be tested
|
|
* against the PHYLINK_PCS_NEG_* definitions.
|
|
*/
|
|
int pcs_config(struct phylink_pcs *pcs, unsigned int neg_mode,
|
|
phy_interface_t interface, const unsigned long *advertising,
|
|
bool permit_pause_to_mac);
|
|
|
|
/**
|
|
* pcs_an_restart() - restart 802.3z BaseX autonegotiation
|
|
* @pcs: a pointer to a &struct phylink_pcs.
|
|
*
|
|
* When PCS ops are present, this overrides mac_an_restart() in &struct
|
|
* phylink_mac_ops.
|
|
*/
|
|
void pcs_an_restart(struct phylink_pcs *pcs);
|
|
|
|
/**
|
|
* pcs_link_up() - program the PCS for the resolved link configuration
|
|
* @pcs: a pointer to a &struct phylink_pcs.
|
|
* @neg_mode: link negotiation mode (see below)
|
|
* @interface: link &typedef phy_interface_t mode
|
|
* @speed: link speed
|
|
* @duplex: link duplex
|
|
*
|
|
* This call will be made just before mac_link_up() to inform the PCS of
|
|
* the resolved link parameters. For example, a PCS operating in SGMII
|
|
* mode without in-band AN needs to be manually configured for the link
|
|
* and duplex setting. Otherwise, this should be a no-op.
|
|
*
|
|
* The %mode argument should be tested via the phylink_mode_*() family of
|
|
* functions, or for PCS that set pcs->neg_mode true, should be tested
|
|
* against the PHYLINK_PCS_NEG_* definitions.
|
|
*/
|
|
void pcs_link_up(struct phylink_pcs *pcs, unsigned int neg_mode,
|
|
phy_interface_t interface, int speed, int duplex);
|
|
#endif
|
|
|
|
void phylink_caps_to_linkmodes(unsigned long *linkmodes, unsigned long caps);
|
|
unsigned long phylink_get_capabilities(phy_interface_t interface,
|
|
unsigned long mac_capabilities,
|
|
int rate_matching);
|
|
void phylink_validate_mask_caps(unsigned long *supported,
|
|
struct phylink_link_state *state,
|
|
unsigned long caps);
|
|
void phylink_generic_validate(struct phylink_config *config,
|
|
unsigned long *supported,
|
|
struct phylink_link_state *state);
|
|
|
|
struct phylink *phylink_create(struct phylink_config *,
|
|
const struct fwnode_handle *,
|
|
phy_interface_t,
|
|
const struct phylink_mac_ops *);
|
|
void phylink_destroy(struct phylink *);
|
|
bool phylink_expects_phy(struct phylink *pl);
|
|
|
|
int phylink_connect_phy(struct phylink *, struct phy_device *);
|
|
int phylink_of_phy_connect(struct phylink *, struct device_node *, u32 flags);
|
|
int phylink_fwnode_phy_connect(struct phylink *pl,
|
|
const struct fwnode_handle *fwnode,
|
|
u32 flags);
|
|
void phylink_disconnect_phy(struct phylink *);
|
|
|
|
void phylink_mac_change(struct phylink *, bool up);
|
|
|
|
void phylink_start(struct phylink *);
|
|
void phylink_stop(struct phylink *);
|
|
|
|
void phylink_suspend(struct phylink *pl, bool mac_wol);
|
|
void phylink_resume(struct phylink *pl);
|
|
|
|
void phylink_ethtool_get_wol(struct phylink *, struct ethtool_wolinfo *);
|
|
int phylink_ethtool_set_wol(struct phylink *, struct ethtool_wolinfo *);
|
|
|
|
int phylink_ethtool_ksettings_get(struct phylink *,
|
|
struct ethtool_link_ksettings *);
|
|
int phylink_ethtool_ksettings_set(struct phylink *,
|
|
const struct ethtool_link_ksettings *);
|
|
int phylink_ethtool_nway_reset(struct phylink *);
|
|
void phylink_ethtool_get_pauseparam(struct phylink *,
|
|
struct ethtool_pauseparam *);
|
|
int phylink_ethtool_set_pauseparam(struct phylink *,
|
|
struct ethtool_pauseparam *);
|
|
int phylink_get_eee_err(struct phylink *);
|
|
int phylink_init_eee(struct phylink *, bool);
|
|
int phylink_ethtool_get_eee(struct phylink *, struct ethtool_eee *);
|
|
int phylink_ethtool_set_eee(struct phylink *, struct ethtool_eee *);
|
|
int phylink_mii_ioctl(struct phylink *, struct ifreq *, int);
|
|
int phylink_speed_down(struct phylink *pl, bool sync);
|
|
int phylink_speed_up(struct phylink *pl);
|
|
|
|
#define phylink_zero(bm) \
|
|
bitmap_zero(bm, __ETHTOOL_LINK_MODE_MASK_NBITS)
|
|
#define __phylink_do_bit(op, bm, mode) \
|
|
op(ETHTOOL_LINK_MODE_ ## mode ## _BIT, bm)
|
|
|
|
#define phylink_set(bm, mode) __phylink_do_bit(__set_bit, bm, mode)
|
|
#define phylink_clear(bm, mode) __phylink_do_bit(__clear_bit, bm, mode)
|
|
#define phylink_test(bm, mode) __phylink_do_bit(test_bit, bm, mode)
|
|
|
|
void phylink_set_port_modes(unsigned long *bits);
|
|
|
|
/**
|
|
* phylink_get_link_timer_ns - return the PCS link timer value
|
|
* @interface: link &typedef phy_interface_t mode
|
|
*
|
|
* Return the PCS link timer setting in nanoseconds for the PHY @interface
|
|
* mode, or -EINVAL if not appropriate.
|
|
*/
|
|
static inline int phylink_get_link_timer_ns(phy_interface_t interface)
|
|
{
|
|
switch (interface) {
|
|
case PHY_INTERFACE_MODE_SGMII:
|
|
case PHY_INTERFACE_MODE_QSGMII:
|
|
case PHY_INTERFACE_MODE_USXGMII:
|
|
return 1600000;
|
|
|
|
case PHY_INTERFACE_MODE_1000BASEX:
|
|
case PHY_INTERFACE_MODE_2500BASEX:
|
|
return 10000000;
|
|
|
|
default:
|
|
return -EINVAL;
|
|
}
|
|
}
|
|
|
|
void phylink_mii_c22_pcs_decode_state(struct phylink_link_state *state,
|
|
u16 bmsr, u16 lpa);
|
|
void phylink_mii_c22_pcs_get_state(struct mdio_device *pcs,
|
|
struct phylink_link_state *state);
|
|
int phylink_mii_c22_pcs_encode_advertisement(phy_interface_t interface,
|
|
const unsigned long *advertising);
|
|
int phylink_mii_c22_pcs_config(struct mdio_device *pcs,
|
|
phy_interface_t interface,
|
|
const unsigned long *advertising,
|
|
unsigned int neg_mode);
|
|
void phylink_mii_c22_pcs_an_restart(struct mdio_device *pcs);
|
|
|
|
void phylink_resolve_c73(struct phylink_link_state *state);
|
|
|
|
void phylink_mii_c45_pcs_get_state(struct mdio_device *pcs,
|
|
struct phylink_link_state *state);
|
|
|
|
void phylink_decode_usxgmii_word(struct phylink_link_state *state,
|
|
uint16_t lpa);
|
|
#endif
|