553 lines
16 KiB
YAML
553 lines
16 KiB
YAML
# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
|
|
%YAML 1.2
|
|
---
|
|
$id: http://devicetree.org/schemas/input/iqs269a.yaml#
|
|
$schema: http://devicetree.org/meta-schemas/core.yaml#
|
|
|
|
title: Azoteq IQS269A Capacitive Touch Controller
|
|
|
|
maintainers:
|
|
- Jeff LaBundy <jeff@labundy.com>
|
|
|
|
description: |
|
|
The Azoteq IQS269A is an 8-channel capacitive touch controller that features
|
|
additional Hall-effect and inductive sensing capabilities.
|
|
|
|
Link to datasheet: https://www.azoteq.com/
|
|
|
|
properties:
|
|
compatible:
|
|
const: azoteq,iqs269a
|
|
|
|
reg:
|
|
maxItems: 1
|
|
|
|
interrupts:
|
|
maxItems: 1
|
|
|
|
"#address-cells":
|
|
const: 1
|
|
|
|
"#size-cells":
|
|
const: 0
|
|
|
|
azoteq,hall-enable:
|
|
type: boolean
|
|
description:
|
|
Enables Hall-effect sensing on channels 6 and 7. In this case, keycodes
|
|
assigned to channel 6 are ignored and keycodes assigned to channel 7 are
|
|
interpreted as switch codes. Refer to the datasheet for requirements im-
|
|
posed on channels 6 and 7 by Hall-effect sensing.
|
|
|
|
azoteq,suspend-mode:
|
|
$ref: /schemas/types.yaml#/definitions/uint32
|
|
enum: [0, 1, 2, 3]
|
|
default: 0
|
|
description: |
|
|
Specifies the power mode during suspend as follows:
|
|
0: Automatic (same as normal runtime, i.e. suspend/resume disabled)
|
|
1: Low power (all sensing at a reduced reporting rate)
|
|
2: Ultra-low power (channel 0 proximity sensing)
|
|
3: Halt (no sensing)
|
|
|
|
azoteq,clk-div:
|
|
type: boolean
|
|
description: Divides the device's core clock by a factor of 4.
|
|
|
|
azoteq,ulp-update:
|
|
$ref: /schemas/types.yaml#/definitions/uint32
|
|
minimum: 0
|
|
maximum: 7
|
|
default: 3
|
|
description: Specifies the ultra-low-power mode update rate.
|
|
|
|
azoteq,reseed-offset:
|
|
type: boolean
|
|
description:
|
|
Applies an 8-count offset to all long-term averages upon either ATI or
|
|
reseed events.
|
|
|
|
azoteq,filt-str-lp-lta:
|
|
$ref: /schemas/types.yaml#/definitions/uint32
|
|
enum: [0, 1, 2, 3]
|
|
default: 0
|
|
description:
|
|
Specifies the long-term average filter strength during low-power mode.
|
|
|
|
azoteq,filt-str-lp-cnt:
|
|
$ref: /schemas/types.yaml#/definitions/uint32
|
|
enum: [0, 1, 2, 3]
|
|
default: 0
|
|
description:
|
|
Specifies the raw count filter strength during low-power mode.
|
|
|
|
azoteq,filt-str-np-lta:
|
|
$ref: /schemas/types.yaml#/definitions/uint32
|
|
enum: [0, 1, 2, 3]
|
|
default: 0
|
|
description:
|
|
Specifies the long-term average filter strength during normal-power mode.
|
|
|
|
azoteq,filt-str-np-cnt:
|
|
$ref: /schemas/types.yaml#/definitions/uint32
|
|
enum: [0, 1, 2, 3]
|
|
default: 0
|
|
description:
|
|
Specifies the raw count filter strength during normal-power mode.
|
|
|
|
azoteq,rate-np-ms:
|
|
minimum: 0
|
|
maximum: 255
|
|
default: 16
|
|
description: Specifies the report rate (in ms) during normal-power mode.
|
|
|
|
azoteq,rate-lp-ms:
|
|
minimum: 0
|
|
maximum: 255
|
|
default: 160
|
|
description: Specifies the report rate (in ms) during low-power mode.
|
|
|
|
azoteq,rate-ulp-ms:
|
|
multipleOf: 16
|
|
minimum: 0
|
|
maximum: 4080
|
|
default: 160
|
|
description: Specifies the report rate (in ms) during ultra-low-power mode.
|
|
|
|
azoteq,timeout-pwr-ms:
|
|
multipleOf: 512
|
|
minimum: 0
|
|
maximum: 130560
|
|
default: 2560
|
|
description:
|
|
Specifies the length of time (in ms) to wait for an event during normal-
|
|
power mode before transitioning to low-power mode.
|
|
|
|
azoteq,timeout-lta-ms:
|
|
multipleOf: 512
|
|
minimum: 0
|
|
maximum: 130560
|
|
default: 32768
|
|
description:
|
|
Specifies the length of time (in ms) to wait before resetting the long-
|
|
term average of all channels. Specify the maximum timeout to disable it
|
|
altogether.
|
|
|
|
azoteq,ati-band-disable:
|
|
type: boolean
|
|
description: Disables the ATI band check.
|
|
|
|
azoteq,ati-lp-only:
|
|
type: boolean
|
|
description: Limits automatic ATI to low-power mode.
|
|
|
|
azoteq,ati-band-tighten:
|
|
type: boolean
|
|
description: Tightens the ATI band from 1/8 to 1/16 of the desired target.
|
|
|
|
azoteq,filt-disable:
|
|
type: boolean
|
|
description: Disables all raw count filtering.
|
|
|
|
azoteq,gpio3-select:
|
|
$ref: /schemas/types.yaml#/definitions/uint32
|
|
minimum: 0
|
|
maximum: 7
|
|
default: 0
|
|
description:
|
|
Selects the channel for which the GPIO3 pin represents touch state.
|
|
|
|
azoteq,dual-direction:
|
|
type: boolean
|
|
description:
|
|
Specifies that long-term averages are to freeze in the presence of either
|
|
increasing or decreasing counts, thereby permitting events to be reported
|
|
in either direction.
|
|
|
|
azoteq,tx-freq:
|
|
$ref: /schemas/types.yaml#/definitions/uint32
|
|
enum: [0, 1, 2, 3]
|
|
default: 0
|
|
description: |
|
|
Specifies the inductive sensing excitation frequency as follows (paren-
|
|
thesized numbers represent the frequency if 'azoteq,clk-div' is present):
|
|
0: 16 MHz (4 MHz)
|
|
1: 8 MHz (2 MHz)
|
|
2: 4 MHz (1 MHz)
|
|
3: 2 MHz (500 kHz)
|
|
|
|
azoteq,global-cap-increase:
|
|
type: boolean
|
|
description: Increases the global capacitance adder from 0.5 pF to 1.5 pF.
|
|
|
|
azoteq,reseed-select:
|
|
$ref: /schemas/types.yaml#/definitions/uint32
|
|
enum: [0, 1, 2, 3]
|
|
default: 0
|
|
description: |
|
|
Specifies the event(s) that prompt the device to reseed (i.e. reset the
|
|
long-term average) of an associated channel as follows:
|
|
0: None
|
|
1: Proximity
|
|
2: Proximity or touch
|
|
3: Proximity, touch or deep touch
|
|
|
|
azoteq,tracking-enable:
|
|
type: boolean
|
|
description:
|
|
Enables all associated channels to track their respective reference
|
|
channels.
|
|
|
|
azoteq,filt-str-slider:
|
|
$ref: /schemas/types.yaml#/definitions/uint32
|
|
enum: [0, 1, 2, 3]
|
|
default: 1
|
|
description: Specifies the slider coordinate filter strength.
|
|
|
|
patternProperties:
|
|
"^channel@[0-7]$":
|
|
type: object
|
|
description:
|
|
Represents a single sensing channel. A channel is active if defined and
|
|
inactive otherwise.
|
|
|
|
properties:
|
|
reg:
|
|
minimum: 0
|
|
maximum: 7
|
|
description: Index of the channel.
|
|
|
|
azoteq,reseed-disable:
|
|
type: boolean
|
|
description:
|
|
Prevents the channel from being reseeded if the long-term average
|
|
timeout (defined in 'azoteq,timeout-lta') expires.
|
|
|
|
azoteq,blocking-enable:
|
|
type: boolean
|
|
description: Specifies that the channel is a blocking channel.
|
|
|
|
azoteq,slider0-select:
|
|
type: boolean
|
|
description: Specifies that the channel participates in slider 0.
|
|
|
|
azoteq,slider1-select:
|
|
type: boolean
|
|
description: Specifies that the channel participates in slider 1.
|
|
|
|
azoteq,rx-enable:
|
|
$ref: /schemas/types.yaml#/definitions/uint32-array
|
|
minItems: 1
|
|
maxItems: 8
|
|
items:
|
|
minimum: 0
|
|
maximum: 7
|
|
description:
|
|
Specifies the CRX pin(s) associated with the channel. By default, only
|
|
the CRX pin corresponding to the channel's index is enabled (e.g. CRX0
|
|
for channel 0).
|
|
|
|
azoteq,tx-enable:
|
|
$ref: /schemas/types.yaml#/definitions/uint32-array
|
|
minItems: 1
|
|
maxItems: 8
|
|
items:
|
|
minimum: 0
|
|
maximum: 7
|
|
default: [0, 1, 2, 3, 4, 5, 6, 7]
|
|
description: Specifies the TX pin(s) associated with the channel.
|
|
|
|
azoteq,meas-cap-decrease:
|
|
type: boolean
|
|
description:
|
|
Decreases the internal measurement capacitance from 60 pF to 15 pF.
|
|
|
|
azoteq,rx-float-inactive:
|
|
type: boolean
|
|
description: Floats any inactive CRX pins instead of grounding them.
|
|
|
|
azoteq,local-cap-size:
|
|
$ref: /schemas/types.yaml#/definitions/uint32
|
|
enum: [0, 1, 2]
|
|
default: 0
|
|
description: |
|
|
Specifies the capacitance to be added to the channel as follows:
|
|
0: None
|
|
1: Global adder (based on 'azoteq,global-cap-increase')
|
|
2: Global adder + 0.5 pF
|
|
|
|
azoteq,invert-enable:
|
|
type: boolean
|
|
description:
|
|
Inverts the polarity of the states reported for proximity, touch and
|
|
deep-touch events relative to their respective thresholds.
|
|
|
|
azoteq,proj-bias:
|
|
$ref: /schemas/types.yaml#/definitions/uint32
|
|
enum: [0, 1, 2, 3]
|
|
default: 2
|
|
description: |
|
|
Specifies the bias current applied during projected-capacitance
|
|
sensing as follows:
|
|
0: 2.5 uA
|
|
1: 5 uA
|
|
2: 10 uA
|
|
3: 20 uA
|
|
|
|
azoteq,sense-mode:
|
|
$ref: /schemas/types.yaml#/definitions/uint32
|
|
enum: [0, 1, 9, 14, 15]
|
|
default: 0
|
|
description: |
|
|
Specifies the channel's sensing mode as follows:
|
|
0: Self capacitance
|
|
1: Projected capacitance
|
|
9: Self or mutual inductance
|
|
14: Hall effect
|
|
15: Temperature
|
|
|
|
azoteq,sense-freq:
|
|
$ref: /schemas/types.yaml#/definitions/uint32
|
|
enum: [0, 1, 2, 3]
|
|
default: 1
|
|
description: |
|
|
Specifies the channel's sensing frequency as follows (parenthesized
|
|
numbers represent the frequency if 'azoteq,clk-div' is present):
|
|
0: 4 MHz (1 MHz)
|
|
1: 2 MHz (500 kHz)
|
|
2: 1 MHz (250 kHz)
|
|
3: 500 kHz (125 kHz)
|
|
|
|
azoteq,static-enable:
|
|
type: boolean
|
|
description: Enables the static front-end for the channel.
|
|
|
|
azoteq,ati-mode:
|
|
$ref: /schemas/types.yaml#/definitions/uint32
|
|
enum: [0, 1, 2, 3]
|
|
default: 3
|
|
description: |
|
|
Specifies the channel's ATI mode as follows:
|
|
0: Disabled
|
|
1: Semi-partial
|
|
2: Partial
|
|
3: Full
|
|
|
|
azoteq,ati-base:
|
|
$ref: /schemas/types.yaml#/definitions/uint32
|
|
enum: [75, 100, 150, 200]
|
|
default: 100
|
|
description: Specifies the channel's ATI base.
|
|
|
|
azoteq,ati-target:
|
|
$ref: /schemas/types.yaml#/definitions/uint32
|
|
multipleOf: 32
|
|
minimum: 0
|
|
maximum: 2016
|
|
default: 512
|
|
description: Specifies the channel's ATI target.
|
|
|
|
azoteq,assoc-select:
|
|
$ref: /schemas/types.yaml#/definitions/uint32-array
|
|
minItems: 1
|
|
maxItems: 8
|
|
items:
|
|
minimum: 0
|
|
maximum: 7
|
|
description:
|
|
Specifies the associated channels for which the channel serves as a
|
|
reference channel. By default, no channels are selected.
|
|
|
|
azoteq,assoc-weight:
|
|
$ref: /schemas/types.yaml#/definitions/uint32
|
|
minimum: 0
|
|
maximum: 255
|
|
default: 0
|
|
description:
|
|
Specifies the channel's impact weight if it acts as an associated
|
|
channel (0 = 0% impact, 255 = 200% impact).
|
|
|
|
patternProperties:
|
|
"^event-prox(-alt)?$":
|
|
type: object
|
|
$ref: input.yaml#
|
|
description:
|
|
Represents a proximity event reported by the channel in response to
|
|
a decrease in counts. Node names suffixed with '-alt' instead corre-
|
|
spond to an increase in counts.
|
|
|
|
By default, the long-term average tracks an increase in counts such
|
|
that only events corresponding to a decrease in counts are reported
|
|
(refer to the datasheet for more information).
|
|
|
|
Specify 'azoteq,dual-direction' to freeze the long-term average when
|
|
the counts increase or decrease such that events of either direction
|
|
can be reported. Alternatively, specify 'azoteq,invert-enable' to in-
|
|
vert the polarity of the states reported by the channel.
|
|
|
|
Complementary events (e.g. event-touch and event-touch-alt) can both
|
|
be present and specify different key or switch codes, but not differ-
|
|
ent thresholds or hysteresis (if applicable).
|
|
|
|
properties:
|
|
azoteq,thresh:
|
|
$ref: /schemas/types.yaml#/definitions/uint32
|
|
minimum: 0
|
|
maximum: 255
|
|
default: 10
|
|
description: Specifies the threshold for the event.
|
|
|
|
linux,code: true
|
|
|
|
additionalProperties: false
|
|
|
|
"^event-touch(-alt)?$":
|
|
type: object
|
|
$ref: input.yaml#
|
|
description: Represents a touch event reported by the channel.
|
|
|
|
properties:
|
|
azoteq,thresh:
|
|
$ref: /schemas/types.yaml#/definitions/uint32
|
|
minimum: 0
|
|
maximum: 255
|
|
default: 8
|
|
description: Specifies the threshold for the event.
|
|
|
|
azoteq,hyst:
|
|
$ref: /schemas/types.yaml#/definitions/uint32
|
|
minimum: 0
|
|
maximum: 15
|
|
default: 4
|
|
description: Specifies the hysteresis for the event.
|
|
|
|
linux,code: true
|
|
|
|
additionalProperties: false
|
|
|
|
"^event-deep(-alt)?$":
|
|
type: object
|
|
$ref: input.yaml#
|
|
description: Represents a deep-touch event reported by the channel.
|
|
|
|
properties:
|
|
azoteq,thresh:
|
|
$ref: /schemas/types.yaml#/definitions/uint32
|
|
minimum: 0
|
|
maximum: 255
|
|
default: 26
|
|
description: Specifies the threshold for the event.
|
|
|
|
azoteq,hyst:
|
|
$ref: /schemas/types.yaml#/definitions/uint32
|
|
minimum: 0
|
|
maximum: 15
|
|
default: 0
|
|
description: Specifies the hysteresis for the event.
|
|
|
|
linux,code: true
|
|
|
|
additionalProperties: false
|
|
|
|
required:
|
|
- reg
|
|
|
|
additionalProperties: false
|
|
|
|
required:
|
|
- compatible
|
|
- reg
|
|
- interrupts
|
|
- "#address-cells"
|
|
- "#size-cells"
|
|
|
|
additionalProperties: false
|
|
|
|
examples:
|
|
- |
|
|
#include <dt-bindings/input/input.h>
|
|
#include <dt-bindings/interrupt-controller/irq.h>
|
|
|
|
i2c {
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
touch@44 {
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
compatible = "azoteq,iqs269a";
|
|
reg = <0x44>;
|
|
interrupt-parent = <&gpio>;
|
|
interrupts = <17 IRQ_TYPE_LEVEL_LOW>;
|
|
|
|
azoteq,hall-enable;
|
|
azoteq,suspend-mode = <2>;
|
|
|
|
channel@0 {
|
|
reg = <0x0>;
|
|
|
|
event-prox {
|
|
linux,code = <KEY_POWER>;
|
|
};
|
|
};
|
|
|
|
channel@1 {
|
|
reg = <0x1>;
|
|
azoteq,slider0-select;
|
|
};
|
|
|
|
channel@2 {
|
|
reg = <0x2>;
|
|
azoteq,slider0-select;
|
|
};
|
|
|
|
channel@3 {
|
|
reg = <0x3>;
|
|
azoteq,slider0-select;
|
|
};
|
|
|
|
channel@4 {
|
|
reg = <0x4>;
|
|
azoteq,slider0-select;
|
|
};
|
|
|
|
channel@5 {
|
|
reg = <0x5>;
|
|
azoteq,slider0-select;
|
|
};
|
|
|
|
channel@6 {
|
|
reg = <0x6>;
|
|
azoteq,invert-enable;
|
|
azoteq,static-enable;
|
|
azoteq,reseed-disable;
|
|
azoteq,rx-enable = <0>;
|
|
azoteq,sense-freq = <0x0>;
|
|
azoteq,sense-mode = <0xE>;
|
|
azoteq,ati-mode = <0x0>;
|
|
azoteq,ati-base = <200>;
|
|
azoteq,ati-target = <320>;
|
|
};
|
|
|
|
channel@7 {
|
|
reg = <0x7>;
|
|
azoteq,invert-enable;
|
|
azoteq,static-enable;
|
|
azoteq,reseed-disable;
|
|
azoteq,rx-enable = <0>, <6>;
|
|
azoteq,sense-freq = <0x0>;
|
|
azoteq,sense-mode = <0xE>;
|
|
azoteq,ati-mode = <0x3>;
|
|
azoteq,ati-base = <200>;
|
|
azoteq,ati-target = <320>;
|
|
|
|
event-touch {
|
|
linux,code = <SW_LID>;
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
...
|