297 lines
5.3 KiB
Plaintext
297 lines
5.3 KiB
Plaintext
// SPDX-License-Identifier: GPL-2.0-only
|
|
|
|
/dts-v1/;
|
|
|
|
#include "msm8916-pm8916.dtsi"
|
|
#include <dt-bindings/gpio/gpio.h>
|
|
#include <dt-bindings/input/input.h>
|
|
#include <dt-bindings/interrupt-controller/irq.h>
|
|
|
|
/ {
|
|
aliases {
|
|
serial0 = &blsp1_uart2;
|
|
};
|
|
|
|
chosen {
|
|
stdout-path = "serial0";
|
|
};
|
|
|
|
reserved-memory {
|
|
/* Additional memory used by Samsung firmware modifications */
|
|
tz-apps@85500000 {
|
|
reg = <0x0 0x85500000 0x0 0xb00000>;
|
|
no-map;
|
|
};
|
|
};
|
|
|
|
gpio-keys {
|
|
compatible = "gpio-keys";
|
|
|
|
pinctrl-0 = <&gpio_keys_default>;
|
|
pinctrl-names = "default";
|
|
|
|
label = "GPIO Buttons";
|
|
|
|
volume-up-button {
|
|
label = "Volume Up";
|
|
gpios = <&msmgpio 107 GPIO_ACTIVE_LOW>;
|
|
linux,code = <KEY_VOLUMEUP>;
|
|
};
|
|
|
|
home-button {
|
|
label = "Home";
|
|
gpios = <&msmgpio 109 GPIO_ACTIVE_LOW>;
|
|
linux,code = <KEY_HOMEPAGE>;
|
|
};
|
|
};
|
|
|
|
gpio-hall-sensor {
|
|
compatible = "gpio-keys";
|
|
|
|
pinctrl-0 = <&gpio_hall_sensor_default>;
|
|
pinctrl-names = "default";
|
|
|
|
label = "GPIO Hall Effect Sensor";
|
|
|
|
hall-sensor-switch {
|
|
label = "Hall Effect Sensor";
|
|
gpios = <&msmgpio 52 GPIO_ACTIVE_LOW>;
|
|
linux,input-type = <EV_SW>;
|
|
linux,code = <SW_LID>;
|
|
linux,can-disable;
|
|
};
|
|
};
|
|
};
|
|
|
|
&blsp_i2c4 {
|
|
status = "okay";
|
|
|
|
fuelgauge@36 {
|
|
compatible = "maxim,max77849-battery";
|
|
reg = <0x36>;
|
|
|
|
maxim,rsns-microohm = <10000>;
|
|
maxim,over-heat-temp = <600>;
|
|
maxim,over-volt = <4400>;
|
|
|
|
interrupt-parent = <&msmgpio>;
|
|
interrupts = <121 IRQ_TYPE_EDGE_FALLING>;
|
|
|
|
pinctrl-0 = <&fuelgauge_int_default>;
|
|
pinctrl-names = "default";
|
|
};
|
|
};
|
|
|
|
&blsp_i2c2 {
|
|
status = "okay";
|
|
|
|
light-sensor@10 {
|
|
compatible = "capella,cm3323";
|
|
reg = <0x10>;
|
|
};
|
|
|
|
accelerometer@1d {
|
|
compatible = "st,lis2hh12";
|
|
reg = <0x1d>;
|
|
|
|
vdd-supply = <&pm8916_l17>;
|
|
vddio-supply = <&pm8916_l5>;
|
|
|
|
interrupt-parent = <&msmgpio>;
|
|
interrupts = <115 IRQ_TYPE_LEVEL_HIGH>;
|
|
interrupt-names = "INT1";
|
|
|
|
st,drdy-int-pin = <1>;
|
|
mount-matrix = "0", "1", "0",
|
|
"-1", "0", "0",
|
|
"0", "0", "1";
|
|
|
|
pinctrl-0 = <&accel_int_default>;
|
|
pinctrl-names = "default";
|
|
};
|
|
};
|
|
|
|
&blsp1_uart2 {
|
|
status = "okay";
|
|
};
|
|
|
|
&pm8916_resin {
|
|
linux,code = <KEY_VOLUMEDOWN>;
|
|
status = "okay";
|
|
};
|
|
|
|
/* FIXME: Replace with MAX77849 MUIC when driver is available */
|
|
&pm8916_usbin {
|
|
status = "okay";
|
|
};
|
|
|
|
&pronto {
|
|
status = "okay";
|
|
|
|
iris {
|
|
compatible = "qcom,wcn3660b";
|
|
};
|
|
};
|
|
|
|
&sdhc_1 {
|
|
pinctrl-0 = <&sdc1_clk_on &sdc1_cmd_on &sdc1_data_on>;
|
|
pinctrl-1 = <&sdc1_clk_off &sdc1_cmd_off &sdc1_data_off>;
|
|
pinctrl-names = "default", "sleep";
|
|
|
|
status = "okay";
|
|
};
|
|
|
|
&sdhc_2 {
|
|
pinctrl-0 = <&sdc2_clk_on &sdc2_cmd_on &sdc2_data_on &sdc2_cd_on>;
|
|
pinctrl-1 = <&sdc2_clk_off &sdc2_cmd_off &sdc2_data_off &sdc2_cd_off>;
|
|
pinctrl-names = "default", "sleep";
|
|
|
|
cd-gpios = <&msmgpio 38 GPIO_ACTIVE_LOW>;
|
|
|
|
status = "okay";
|
|
};
|
|
|
|
&usb {
|
|
dr_mode = "peripheral";
|
|
extcon = <&pm8916_usbin>;
|
|
|
|
status = "okay";
|
|
};
|
|
|
|
&usb_hs_phy {
|
|
extcon = <&pm8916_usbin>;
|
|
};
|
|
|
|
&smd_rpm_regulators {
|
|
vdd_l1_l2_l3-supply = <&pm8916_s3>;
|
|
vdd_l4_l5_l6-supply = <&pm8916_s4>;
|
|
vdd_l7-supply = <&pm8916_s4>;
|
|
|
|
s3 {
|
|
regulator-min-microvolt = <1200000>;
|
|
regulator-max-microvolt = <1300000>;
|
|
};
|
|
|
|
s4 {
|
|
regulator-min-microvolt = <1800000>;
|
|
regulator-max-microvolt = <2100000>;
|
|
};
|
|
|
|
l1 {
|
|
regulator-min-microvolt = <1225000>;
|
|
regulator-max-microvolt = <1225000>;
|
|
};
|
|
|
|
l2 {
|
|
regulator-min-microvolt = <1200000>;
|
|
regulator-max-microvolt = <1200000>;
|
|
};
|
|
|
|
l4 {
|
|
regulator-min-microvolt = <2050000>;
|
|
regulator-max-microvolt = <2050000>;
|
|
};
|
|
|
|
l5 {
|
|
regulator-min-microvolt = <1800000>;
|
|
regulator-max-microvolt = <1800000>;
|
|
};
|
|
|
|
l6 {
|
|
regulator-min-microvolt = <1800000>;
|
|
regulator-max-microvolt = <1800000>;
|
|
};
|
|
|
|
l7 {
|
|
regulator-min-microvolt = <1800000>;
|
|
regulator-max-microvolt = <1800000>;
|
|
};
|
|
|
|
l8 {
|
|
regulator-min-microvolt = <2850000>;
|
|
regulator-max-microvolt = <2900000>;
|
|
};
|
|
|
|
l9 {
|
|
regulator-min-microvolt = <3300000>;
|
|
regulator-max-microvolt = <3300000>;
|
|
};
|
|
|
|
l10 {
|
|
regulator-min-microvolt = <2700000>;
|
|
regulator-max-microvolt = <2800000>;
|
|
};
|
|
|
|
l11 {
|
|
regulator-min-microvolt = <1800000>;
|
|
regulator-max-microvolt = <2950000>;
|
|
regulator-system-load = <200000>;
|
|
regulator-allow-set-load;
|
|
};
|
|
|
|
l12 {
|
|
regulator-min-microvolt = <1800000>;
|
|
regulator-max-microvolt = <2950000>;
|
|
};
|
|
|
|
l13 {
|
|
regulator-min-microvolt = <3075000>;
|
|
regulator-max-microvolt = <3075000>;
|
|
};
|
|
|
|
l14 {
|
|
regulator-min-microvolt = <1800000>;
|
|
regulator-max-microvolt = <3300000>;
|
|
};
|
|
|
|
l15 {
|
|
regulator-min-microvolt = <1800000>;
|
|
regulator-max-microvolt = <3300000>;
|
|
};
|
|
|
|
l16 {
|
|
regulator-min-microvolt = <1800000>;
|
|
regulator-max-microvolt = <3300000>;
|
|
};
|
|
|
|
l17 {
|
|
regulator-min-microvolt = <2850000>;
|
|
regulator-max-microvolt = <2850000>;
|
|
};
|
|
|
|
l18 {
|
|
regulator-min-microvolt = <2700000>;
|
|
regulator-max-microvolt = <2700000>;
|
|
};
|
|
};
|
|
|
|
&msmgpio {
|
|
accel_int_default: accel-int-default-state {
|
|
pins = "gpio115";
|
|
function = "gpio";
|
|
drive-strength = <2>;
|
|
bias-disable;
|
|
};
|
|
|
|
fuelgauge_int_default: fuelgauge-int-default-state {
|
|
pins = "gpio121";
|
|
function = "gpio";
|
|
drive-strength = <2>;
|
|
bias-disable;
|
|
};
|
|
|
|
gpio_keys_default: gpio-keys-default-state {
|
|
pins = "gpio107", "gpio109";
|
|
function = "gpio";
|
|
drive-strength = <2>;
|
|
bias-pull-up;
|
|
};
|
|
|
|
gpio_hall_sensor_default: gpio-hall-sensor-default-state {
|
|
pins = "gpio52";
|
|
function = "gpio";
|
|
drive-strength = <2>;
|
|
bias-disable;
|
|
};
|
|
};
|