155 lines
3.1 KiB
Plaintext
155 lines
3.1 KiB
Plaintext
// SPDX-License-Identifier: BSD-3-Clause
|
|
|
|
#include <dt-bindings/iio/qcom,spmi-vadc.h>
|
|
#include <dt-bindings/input/input.h>
|
|
#include <dt-bindings/input/linux-event-codes.h>
|
|
#include <dt-bindings/interrupt-controller/irq.h>
|
|
#include <dt-bindings/spmi/spmi.h>
|
|
|
|
/ {
|
|
thermal-zones {
|
|
pm6125-thermal {
|
|
polling-delay-passive = <100>;
|
|
polling-delay = <0>;
|
|
|
|
thermal-sensors = <&pm6125_temp>;
|
|
|
|
trips {
|
|
trip0 {
|
|
temperature = <95000>;
|
|
hysteresis = <0>;
|
|
type = "passive";
|
|
};
|
|
|
|
trip1 {
|
|
temperature = <115000>;
|
|
hysteresis = <0>;
|
|
type = "hot";
|
|
};
|
|
|
|
trip2 {
|
|
temperature = <145000>;
|
|
hysteresis = <0>;
|
|
type = "critical";
|
|
};
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
&spmi_bus {
|
|
pmic@0 {
|
|
compatible = "qcom,pm6125", "qcom,spmi-pmic";
|
|
reg = <0x0 SPMI_USID>;
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
pm6125_pon: pon@800 {
|
|
compatible = "qcom,pm8998-pon";
|
|
reg = <0x800>;
|
|
mode-bootloader = <0x2>;
|
|
mode-recovery = <0x1>;
|
|
|
|
pon_pwrkey: pwrkey {
|
|
compatible = "qcom,pm8941-pwrkey";
|
|
interrupts = <0x0 0x8 0x0 IRQ_TYPE_EDGE_BOTH>;
|
|
debounce = <15625>;
|
|
linux,code = <KEY_POWER>;
|
|
bias-pull-up;
|
|
status = "disabled";
|
|
};
|
|
|
|
pon_resin: resin {
|
|
compatible = "qcom,pm8941-resin";
|
|
interrupts = <0x0 0x8 0x1 IRQ_TYPE_EDGE_BOTH>;
|
|
debounce = <15625>;
|
|
bias-pull-up;
|
|
status = "disabled";
|
|
};
|
|
};
|
|
|
|
pm6125_temp: temp-alarm@2400 {
|
|
compatible = "qcom,spmi-temp-alarm";
|
|
reg = <0x2400>;
|
|
interrupts = <0x0 0x24 0x0 IRQ_TYPE_EDGE_RISING>;
|
|
io-channels = <&pm6125_adc ADC5_DIE_TEMP>;
|
|
io-channel-names = "thermal";
|
|
#thermal-sensor-cells = <0>;
|
|
};
|
|
|
|
pm6125_adc: adc@3100 {
|
|
compatible = "qcom,spmi-adc5";
|
|
reg = <0x3100>;
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
interrupts = <0x0 0x31 0x0 IRQ_TYPE_EDGE_RISING>;
|
|
#io-channel-cells = <1>;
|
|
|
|
ref-gnd@0 {
|
|
reg = <ADC5_REF_GND>;
|
|
qcom,pre-scaling = <1 1>;
|
|
};
|
|
|
|
vref-1p25@1 {
|
|
reg = <ADC5_1P25VREF>;
|
|
qcom,pre-scaling = <1 1>;
|
|
};
|
|
|
|
die-temp@6 {
|
|
reg = <ADC5_DIE_TEMP>;
|
|
qcom,pre-scaling = <1 1>;
|
|
};
|
|
|
|
vph-pwr@83 {
|
|
reg = <ADC5_VPH_PWR>;
|
|
qcom,pre-scaling = <1 3>;
|
|
};
|
|
|
|
vcoin@85 {
|
|
reg = <ADC5_VCOIN>;
|
|
qcom,pre-scaling = <1 3>;
|
|
};
|
|
|
|
xo-therm@4c {
|
|
reg = <ADC5_XO_THERM_100K_PU>;
|
|
qcom,pre-scaling = <1 1>;
|
|
qcom,hw-settle-time = <200>;
|
|
qcom,ratiometric;
|
|
};
|
|
};
|
|
|
|
pm6125_adc_tm: adc-tm@3500 {
|
|
compatible = "qcom,spmi-adc-tm5";
|
|
reg = <0x3500>;
|
|
interrupts = <0x0 0x35 0x0 IRQ_TYPE_EDGE_RISING>;
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
#thermal-sensor-cells = <1>;
|
|
status = "disabled";
|
|
};
|
|
|
|
pm6125_rtc: rtc@6000 {
|
|
compatible = "qcom,pm8941-rtc";
|
|
reg = <0x6000>, <0x6100>;
|
|
reg-names = "rtc", "alarm";
|
|
interrupts = <0x0 0x61 0x1 IRQ_TYPE_EDGE_RISING>;
|
|
status = "disabled";
|
|
};
|
|
|
|
pm6125_gpios: gpio@c000 {
|
|
compatible = "qcom,pm6125-gpio", "qcom,spmi-gpio";
|
|
reg = <0xc000>;
|
|
gpio-controller;
|
|
gpio-ranges = <&pm6125_gpios 0 0 9>;
|
|
#gpio-cells = <2>;
|
|
interrupt-controller;
|
|
#interrupt-cells = <2>;
|
|
};
|
|
};
|
|
|
|
pmic@1 {
|
|
compatible = "qcom,pm6125", "qcom,spmi-pmic";
|
|
reg = <0x1 SPMI_USID>;
|
|
};
|
|
};
|