143 lines
2.9 KiB
Plaintext
143 lines
2.9 KiB
Plaintext
// SPDX-License-Identifier: GPL-2.0
|
|
/*
|
|
* Copyright (c) 2018, Linaro Limited
|
|
*/
|
|
|
|
#include <dt-bindings/spmi/spmi.h>
|
|
#include <dt-bindings/input/linux-event-codes.h>
|
|
#include <dt-bindings/iio/qcom,spmi-vadc.h>
|
|
#include <dt-bindings/thermal/thermal.h>
|
|
|
|
/ {
|
|
thermal-zones {
|
|
pms405-thermal {
|
|
polling-delay-passive = <250>;
|
|
polling-delay = <1000>;
|
|
|
|
thermal-sensors = <&pms405_temp>;
|
|
|
|
trips {
|
|
pms405_alert0: pms405-alert0 {
|
|
temperature = <105000>;
|
|
hysteresis = <2000>;
|
|
type = "passive";
|
|
};
|
|
pms405_crit: pms405-crit {
|
|
temperature = <125000>;
|
|
hysteresis = <2000>;
|
|
type = "critical";
|
|
};
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
&spmi_bus {
|
|
pms405_0: pms405@0 {
|
|
compatible = "qcom,pms405", "qcom,spmi-pmic";
|
|
reg = <0x0 SPMI_USID>;
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
pms405_gpios: gpio@c000 {
|
|
compatible = "qcom,pms405-gpio", "qcom,spmi-gpio";
|
|
reg = <0xc000>;
|
|
gpio-controller;
|
|
gpio-ranges = <&pms405_gpios 0 0 12>;
|
|
#gpio-cells = <2>;
|
|
interrupt-controller;
|
|
#interrupt-cells = <2>;
|
|
};
|
|
|
|
pon@800 {
|
|
compatible = "qcom,pms405-pon";
|
|
reg = <0x0800>;
|
|
mode-bootloader = <0x2>;
|
|
mode-recovery = <0x1>;
|
|
|
|
pwrkey {
|
|
compatible = "qcom,pm8941-pwrkey";
|
|
interrupts = <0x0 0x8 0 IRQ_TYPE_EDGE_BOTH>;
|
|
debounce = <15625>;
|
|
bias-pull-up;
|
|
linux,code = <KEY_POWER>;
|
|
};
|
|
};
|
|
|
|
pms405_temp: temp-alarm@2400 {
|
|
compatible = "qcom,spmi-temp-alarm";
|
|
reg = <0x2400>;
|
|
interrupts = <0 0x24 0 IRQ_TYPE_EDGE_RISING>;
|
|
io-channels = <&pms405_adc ADC5_DIE_TEMP>;
|
|
io-channel-names = "thermal";
|
|
#thermal-sensor-cells = <0>;
|
|
};
|
|
|
|
pms405_adc: adc@3100 {
|
|
compatible = "qcom,pms405-adc", "qcom,spmi-adc-rev2";
|
|
reg = <0x3100>;
|
|
interrupts = <0x0 0x31 0x0 IRQ_TYPE_EDGE_RISING>;
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
#io-channel-cells = <1>;
|
|
|
|
ref_gnd@0 {
|
|
reg = <ADC5_REF_GND>;
|
|
qcom,pre-scaling = <1 1>;
|
|
};
|
|
|
|
vref_1p25@1 {
|
|
reg = <ADC5_1P25VREF>;
|
|
qcom,pre-scaling = <1 1>;
|
|
};
|
|
|
|
pon_1: vph_pwr@131 {
|
|
reg = <ADC5_VPH_PWR>;
|
|
qcom,pre-scaling = <1 3>;
|
|
};
|
|
|
|
die_temp@6 {
|
|
reg = <ADC5_DIE_TEMP>;
|
|
qcom,pre-scaling = <1 1>;
|
|
};
|
|
|
|
pa_therm1: thermistor1@77 {
|
|
reg = <ADC5_AMUX_THM1_100K_PU>;
|
|
qcom,ratiometric;
|
|
qcom,hw-settle-time = <200>;
|
|
qcom,pre-scaling = <1 1>;
|
|
};
|
|
|
|
pa_therm3: thermistor3@79 {
|
|
reg = <ADC5_AMUX_THM3_100K_PU>;
|
|
qcom,ratiometric;
|
|
qcom,hw-settle-time = <200>;
|
|
qcom,pre-scaling = <1 1>;
|
|
};
|
|
|
|
xo_therm: xo_temp@76 {
|
|
reg = <ADC5_XO_THERM_100K_PU>;
|
|
qcom,ratiometric;
|
|
qcom,hw-settle-time = <200>;
|
|
qcom,pre-scaling = <1 1>;
|
|
};
|
|
};
|
|
|
|
rtc@6000 {
|
|
compatible = "qcom,pm8941-rtc";
|
|
reg = <0x6000>, <0x6100>;
|
|
reg-names = "rtc", "alarm";
|
|
interrupts = <0x0 0x61 0x1 IRQ_TYPE_NONE>;
|
|
};
|
|
};
|
|
|
|
pms405_1: pms405@1 {
|
|
compatible = "qcom,pms405", "qcom,spmi-pmic";
|
|
reg = <0x1 SPMI_USID>;
|
|
|
|
pms405_spmi_regulators: regulators {
|
|
compatible = "qcom,pms405-regulators";
|
|
};
|
|
};
|
|
};
|