565 lines
11 KiB
Plaintext
565 lines
11 KiB
Plaintext
// SPDX-License-Identifier: GPL-2.0
|
|
|
|
/dts-v1/;
|
|
|
|
#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
|
|
#include <dt-bindings/regulator/qcom,rpmh-regulator.h>
|
|
#include <dt-bindings/sound/qcom,q6afe.h>
|
|
#include <dt-bindings/sound/qcom,q6asm.h>
|
|
#include "sdm845.dtsi"
|
|
#include "sdm845-wcd9340.dtsi"
|
|
#include "pm8998.dtsi"
|
|
#include "pmi8998.dtsi"
|
|
|
|
/*
|
|
* Delete following upstream (sdm845.dtsi) reserved
|
|
* memory mappings which are different in this device.
|
|
*/
|
|
/delete-node/ &tz_mem;
|
|
/delete-node/ &adsp_mem;
|
|
/delete-node/ &wlan_msa_mem;
|
|
/delete-node/ &mpss_region;
|
|
/delete-node/ &venus_mem;
|
|
/delete-node/ &cdsp_mem;
|
|
/delete-node/ &mba_region;
|
|
/delete-node/ &slpi_mem;
|
|
/delete-node/ &spss_mem;
|
|
/delete-node/ &rmtfs_mem;
|
|
|
|
/ {
|
|
chassis-type = "handset";
|
|
|
|
/* required for bootloader to select correct board */
|
|
qcom,board-id = <69 0>;
|
|
qcom,msm-id = <321 0x20001>;
|
|
|
|
aliases {
|
|
serial1 = &uart6;
|
|
};
|
|
|
|
gpio-keys {
|
|
compatible = "gpio-keys";
|
|
autorepeat;
|
|
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&vol_up_pin_a>;
|
|
|
|
key-vol-up {
|
|
label = "Volume Up";
|
|
linux,code = <KEY_VOLUMEUP>;
|
|
gpios = <&pm8998_gpios 6 GPIO_ACTIVE_LOW>;
|
|
};
|
|
};
|
|
|
|
/* Reserved memory changes from downstream */
|
|
reserved-memory {
|
|
tz_mem: memory@86200000 {
|
|
reg = <0 0x86200000 0 0x4900000>;
|
|
no-map;
|
|
};
|
|
|
|
adsp_mem: memory@8c500000 {
|
|
reg = <0 0x8c500000 0 0x1e00000>;
|
|
no-map;
|
|
};
|
|
|
|
wlan_msa_mem: memory@8e300000 {
|
|
reg = <0 0x8e300000 0 0x100000>;
|
|
no-map;
|
|
};
|
|
|
|
mpss_region: memory@8e400000 {
|
|
reg = <0 0x8e400000 0 0x7800000>;
|
|
no-map;
|
|
};
|
|
|
|
venus_mem: memory@95c00000 {
|
|
reg = <0 0x95c00000 0 0x500000>;
|
|
no-map;
|
|
};
|
|
|
|
cdsp_mem: memory@96100000 {
|
|
reg = <0 0x96100000 0 0x800000>;
|
|
no-map;
|
|
};
|
|
|
|
mba_region: memory@96900000 {
|
|
reg = <0 0x96900000 0 0x200000>;
|
|
no-map;
|
|
};
|
|
|
|
slpi_mem: memory@96b00000 {
|
|
reg = <0 0x96b00000 0 0x1400000>;
|
|
no-map;
|
|
};
|
|
|
|
spss_mem: memory@97f00000 {
|
|
reg = <0 0x97f00000 0 0x100000>;
|
|
no-map;
|
|
};
|
|
|
|
/* Cont splash region set up by the bootloader */
|
|
cont_splash_mem: framebuffer@9d400000 {
|
|
reg = <0 0x9d400000 0 0x2400000>;
|
|
no-map;
|
|
};
|
|
|
|
rmtfs_mem: memory@f6301000 {
|
|
compatible = "qcom,rmtfs-mem";
|
|
reg = <0 0xf6301000 0 0x200000>;
|
|
no-map;
|
|
|
|
qcom,client-id = <1>;
|
|
qcom,vmid = <15>;
|
|
};
|
|
};
|
|
|
|
vreg_s4a_1p8: vreg-s4a-1p8 {
|
|
compatible = "regulator-fixed";
|
|
regulator-name = "vreg_s4a_1p8";
|
|
|
|
regulator-min-microvolt = <1800000>;
|
|
regulator-max-microvolt = <1800000>;
|
|
regulator-always-on;
|
|
};
|
|
};
|
|
|
|
&adsp_pas {
|
|
status = "okay";
|
|
firmware-name = "qcom/sdm845/beryllium/adsp.mbn";
|
|
};
|
|
|
|
&apps_rsc {
|
|
regulators-0 {
|
|
compatible = "qcom,pm8998-rpmh-regulators";
|
|
qcom,pmic-id = "a";
|
|
|
|
vreg_l1a_0p875: ldo1 {
|
|
regulator-min-microvolt = <880000>;
|
|
regulator-max-microvolt = <880000>;
|
|
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
|
|
};
|
|
|
|
vreg_l5a_0p8: ldo5 {
|
|
regulator-min-microvolt = <800000>;
|
|
regulator-max-microvolt = <800000>;
|
|
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
|
|
};
|
|
|
|
vreg_l7a_1p8: ldo7 {
|
|
regulator-min-microvolt = <1800000>;
|
|
regulator-max-microvolt = <1800000>;
|
|
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
|
|
};
|
|
|
|
vreg_l12a_1p8: ldo12 {
|
|
regulator-min-microvolt = <1800000>;
|
|
regulator-max-microvolt = <1800000>;
|
|
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
|
|
};
|
|
|
|
vreg_l13a_2p95: ldo13 {
|
|
regulator-min-microvolt = <1800000>;
|
|
regulator-max-microvolt = <2960000>;
|
|
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
|
|
};
|
|
|
|
vreg_l14a_1p8: ldo14 {
|
|
regulator-min-microvolt = <1800000>;
|
|
regulator-max-microvolt = <1800000>;
|
|
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
|
|
regulator-boot-on;
|
|
regulator-always-on;
|
|
};
|
|
|
|
vreg_l17a_1p3: ldo17 {
|
|
regulator-min-microvolt = <1304000>;
|
|
regulator-max-microvolt = <1304000>;
|
|
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
|
|
};
|
|
|
|
vreg_l20a_2p95: ldo20 {
|
|
regulator-min-microvolt = <2960000>;
|
|
regulator-max-microvolt = <2968000>;
|
|
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
|
|
};
|
|
|
|
vreg_l21a_2p95: ldo21 {
|
|
regulator-min-microvolt = <2960000>;
|
|
regulator-max-microvolt = <2968000>;
|
|
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
|
|
};
|
|
|
|
vreg_l23a_3p3: ldo23 {
|
|
regulator-min-microvolt = <3300000>;
|
|
regulator-max-microvolt = <3312000>;
|
|
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
|
|
};
|
|
|
|
vreg_l24a_3p075: ldo24 {
|
|
regulator-min-microvolt = <3088000>;
|
|
regulator-max-microvolt = <3088000>;
|
|
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
|
|
};
|
|
|
|
vreg_l25a_3p3: ldo25 {
|
|
regulator-min-microvolt = <3300000>;
|
|
regulator-max-microvolt = <3312000>;
|
|
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
|
|
};
|
|
|
|
vreg_l26a_1p2: ldo26 {
|
|
regulator-min-microvolt = <1200000>;
|
|
regulator-max-microvolt = <1200000>;
|
|
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
|
|
regulator-boot-on;
|
|
};
|
|
};
|
|
};
|
|
|
|
&cdsp_pas {
|
|
status = "okay";
|
|
firmware-name = "qcom/sdm845/beryllium/cdsp.mbn";
|
|
};
|
|
|
|
&dsi0 {
|
|
status = "okay";
|
|
vdda-supply = <&vreg_l26a_1p2>;
|
|
|
|
display_panel: panel@0 {
|
|
reg = <0>;
|
|
vddio-supply = <&vreg_l14a_1p8>;
|
|
vddpos-supply = <&lab>;
|
|
vddneg-supply = <&ibb>;
|
|
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
backlight = <&pmi8998_wled>;
|
|
reset-gpios = <&tlmm 6 GPIO_ACTIVE_LOW>;
|
|
|
|
status = "disabled";
|
|
|
|
port {
|
|
panel_in_0: endpoint {
|
|
remote-endpoint = <&dsi0_out>;
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
&dsi0_out {
|
|
remote-endpoint = <&panel_in_0>;
|
|
data-lanes = <0 1 2 3>;
|
|
};
|
|
|
|
&dsi0_phy {
|
|
status = "okay";
|
|
vdds-supply = <&vreg_l1a_0p875>;
|
|
};
|
|
|
|
&gcc {
|
|
protected-clocks = <GCC_QSPI_CORE_CLK>,
|
|
<GCC_QSPI_CORE_CLK_SRC>,
|
|
<GCC_QSPI_CNOC_PERIPH_AHB_CLK>,
|
|
<GCC_LPASS_Q6_AXI_CLK>,
|
|
<GCC_LPASS_SWAY_CLK>;
|
|
};
|
|
|
|
&gmu {
|
|
status = "okay";
|
|
};
|
|
|
|
&gpu {
|
|
status = "okay";
|
|
|
|
zap-shader {
|
|
memory-region = <&gpu_mem>;
|
|
firmware-name = "qcom/sdm845/beryllium/a630_zap.mbn";
|
|
};
|
|
};
|
|
|
|
&ibb {
|
|
regulator-min-microvolt = <4600000>;
|
|
regulator-max-microvolt = <6000000>;
|
|
regulator-over-current-protection;
|
|
regulator-pull-down;
|
|
regulator-soft-start;
|
|
qcom,discharge-resistor-kohms = <300>;
|
|
};
|
|
|
|
&lab {
|
|
regulator-min-microvolt = <4600000>;
|
|
regulator-max-microvolt = <6000000>;
|
|
regulator-over-current-protection;
|
|
regulator-pull-down;
|
|
regulator-soft-start;
|
|
};
|
|
|
|
&mdss {
|
|
status = "okay";
|
|
};
|
|
|
|
&mss_pil {
|
|
status = "okay";
|
|
firmware-name = "qcom/sdm845/beryllium/mba.mbn", "qcom/sdm845/beryllium/modem.mbn";
|
|
};
|
|
|
|
&ipa {
|
|
qcom,gsi-loader = "self";
|
|
memory-region = <&ipa_fw_mem>;
|
|
firmware-name = "qcom/sdm845/beryllium/ipa_fws.mbn";
|
|
status = "okay";
|
|
};
|
|
|
|
&pm8998_gpios {
|
|
vol_up_pin_a: vol-up-active-state {
|
|
pins = "gpio6";
|
|
function = "normal";
|
|
input-enable;
|
|
bias-pull-up;
|
|
qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>;
|
|
};
|
|
};
|
|
|
|
&pmi8998_wled {
|
|
status = "okay";
|
|
qcom,current-boost-limit = <970>;
|
|
qcom,ovp-millivolt = <29600>;
|
|
qcom,current-limit-microamp = <20000>;
|
|
qcom,num-strings = <2>;
|
|
qcom,switching-freq = <600>;
|
|
qcom,external-pfet;
|
|
qcom,cabc;
|
|
};
|
|
|
|
&pm8998_resin {
|
|
linux,code = <KEY_VOLUMEDOWN>;
|
|
status = "okay";
|
|
};
|
|
|
|
&pmi8998_rradc {
|
|
status = "okay";
|
|
};
|
|
|
|
/* QUAT I2S Uses 1 I2S SD Line for audio on TAS2559/60 amplifiers */
|
|
&q6afedai {
|
|
dai@22 {
|
|
reg = <QUATERNARY_MI2S_RX>;
|
|
qcom,sd-lines = <0>;
|
|
};
|
|
};
|
|
|
|
&q6asmdai {
|
|
dai@0 {
|
|
reg = <0>;
|
|
};
|
|
|
|
dai@1 {
|
|
reg = <1>;
|
|
};
|
|
|
|
dai@2 {
|
|
reg = <2>;
|
|
};
|
|
};
|
|
|
|
&qupv3_id_0 {
|
|
status = "okay";
|
|
};
|
|
|
|
&sdhc_2 {
|
|
status = "okay";
|
|
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&sdc2_default_state &sdc2_card_det_n>;
|
|
|
|
vmmc-supply = <&vreg_l21a_2p95>;
|
|
vqmmc-supply = <&vreg_l13a_2p95>;
|
|
|
|
bus-width = <4>;
|
|
cd-gpios = <&tlmm 126 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
|
|
&sound {
|
|
compatible = "qcom,db845c-sndcard", "qcom,sdm845-sndcard";
|
|
pinctrl-0 = <&quat_mi2s_active
|
|
&quat_mi2s_sd0_active>;
|
|
pinctrl-names = "default";
|
|
model = "Xiaomi Poco F1";
|
|
audio-routing =
|
|
"RX_BIAS", "MCLK",
|
|
"AMIC1", "MIC BIAS1",
|
|
"AMIC2", "MIC BIAS2",
|
|
"AMIC3", "MIC BIAS3";
|
|
|
|
mm1-dai-link {
|
|
link-name = "MultiMedia1";
|
|
cpu {
|
|
sound-dai = <&q6asmdai MSM_FRONTEND_DAI_MULTIMEDIA1>;
|
|
};
|
|
};
|
|
|
|
mm2-dai-link {
|
|
link-name = "MultiMedia2";
|
|
cpu {
|
|
sound-dai = <&q6asmdai MSM_FRONTEND_DAI_MULTIMEDIA2>;
|
|
};
|
|
};
|
|
|
|
mm3-dai-link {
|
|
link-name = "MultiMedia3";
|
|
cpu {
|
|
sound-dai = <&q6asmdai MSM_FRONTEND_DAI_MULTIMEDIA3>;
|
|
};
|
|
};
|
|
|
|
slim-dai-link {
|
|
link-name = "SLIM Playback";
|
|
cpu {
|
|
sound-dai = <&q6afedai SLIMBUS_0_RX>;
|
|
};
|
|
|
|
platform {
|
|
sound-dai = <&q6routing>;
|
|
};
|
|
|
|
codec {
|
|
sound-dai = <&wcd9340 0>;
|
|
};
|
|
};
|
|
|
|
slimcap-dai-link {
|
|
link-name = "SLIM Capture";
|
|
cpu {
|
|
sound-dai = <&q6afedai SLIMBUS_0_TX>;
|
|
};
|
|
|
|
platform {
|
|
sound-dai = <&q6routing>;
|
|
};
|
|
|
|
codec {
|
|
sound-dai = <&wcd9340 1>;
|
|
};
|
|
};
|
|
};
|
|
|
|
&tlmm {
|
|
gpio-reserved-ranges = <0 4>, <81 4>;
|
|
|
|
sdc2_default_state: sdc2-default-state {
|
|
clk-pins {
|
|
pins = "sdc2_clk";
|
|
bias-disable;
|
|
drive-strength = <16>;
|
|
};
|
|
|
|
cmd-pins {
|
|
pins = "sdc2_cmd";
|
|
bias-pull-up;
|
|
drive-strength = <10>;
|
|
};
|
|
|
|
data-pins {
|
|
pins = "sdc2_data";
|
|
bias-pull-up;
|
|
drive-strength = <10>;
|
|
};
|
|
};
|
|
|
|
sdc2_card_det_n: sd-card-det-n-state {
|
|
pins = "gpio126";
|
|
function = "gpio";
|
|
bias-pull-up;
|
|
};
|
|
};
|
|
|
|
&uart6 {
|
|
status = "okay";
|
|
|
|
pinctrl-0 = <&qup_uart6_4pin>;
|
|
|
|
bluetooth {
|
|
compatible = "qcom,wcn3990-bt";
|
|
|
|
vddio-supply = <&vreg_s4a_1p8>;
|
|
vddxo-supply = <&vreg_l7a_1p8>;
|
|
vddrf-supply = <&vreg_l17a_1p3>;
|
|
vddch0-supply = <&vreg_l25a_3p3>;
|
|
max-speed = <3200000>;
|
|
};
|
|
};
|
|
|
|
&ufs_mem_hc {
|
|
status = "okay";
|
|
|
|
reset-gpios = <&tlmm 150 GPIO_ACTIVE_LOW>;
|
|
|
|
vcc-supply = <&vreg_l20a_2p95>;
|
|
vcc-max-microamp = <800000>;
|
|
};
|
|
|
|
&ufs_mem_phy {
|
|
status = "okay";
|
|
|
|
vdda-phy-supply = <&vreg_l1a_0p875>;
|
|
vdda-pll-supply = <&vreg_l26a_1p2>;
|
|
};
|
|
|
|
&usb_1 {
|
|
status = "okay";
|
|
};
|
|
|
|
&usb_1_dwc3 {
|
|
dr_mode = "peripheral";
|
|
};
|
|
|
|
&usb_1_hsphy {
|
|
status = "okay";
|
|
|
|
vdd-supply = <&vreg_l1a_0p875>;
|
|
vdda-pll-supply = <&vreg_l12a_1p8>;
|
|
vdda-phy-dpdm-supply = <&vreg_l24a_3p075>;
|
|
|
|
qcom,imp-res-offset-value = <8>;
|
|
qcom,hstx-trim-value = <QUSB2_V2_HSTX_TRIM_21_6_MA>;
|
|
qcom,preemphasis-level = <QUSB2_V2_PREEMPHASIS_5_PERCENT>;
|
|
qcom,preemphasis-width = <QUSB2_V2_PREEMPHASIS_WIDTH_HALF_BIT>;
|
|
};
|
|
|
|
&usb_1_qmpphy {
|
|
status = "okay";
|
|
|
|
vdda-phy-supply = <&vreg_l26a_1p2>;
|
|
vdda-pll-supply = <&vreg_l1a_0p875>;
|
|
};
|
|
|
|
&venus {
|
|
status = "okay";
|
|
firmware-name = "qcom/sdm845/beryllium/venus.mbn";
|
|
};
|
|
|
|
&wcd9340 {
|
|
reset-gpios = <&tlmm 64 GPIO_ACTIVE_HIGH>;
|
|
vdd-buck-supply = <&vreg_s4a_1p8>;
|
|
vdd-buck-sido-supply = <&vreg_s4a_1p8>;
|
|
vdd-tx-supply = <&vreg_s4a_1p8>;
|
|
vdd-rx-supply = <&vreg_s4a_1p8>;
|
|
vdd-io-supply = <&vreg_s4a_1p8>;
|
|
qcom,micbias1-microvolt = <2700000>;
|
|
qcom,micbias2-microvolt = <1800000>;
|
|
qcom,micbias3-microvolt = <2700000>;
|
|
qcom,micbias4-microvolt = <2700000>;
|
|
};
|
|
|
|
&wifi {
|
|
status = "okay";
|
|
|
|
vdd-0.8-cx-mx-supply = <&vreg_l5a_0p8>;
|
|
vdd-1.8-xo-supply = <&vreg_l7a_1p8>;
|
|
vdd-1.3-rfa-supply = <&vreg_l17a_1p3>;
|
|
vdd-3.3-ch0-supply = <&vreg_l25a_3p3>;
|
|
vdd-3.3-ch1-supply = <&vreg_l23a_3p3>;
|
|
};
|