555 lines
22 KiB
C
555 lines
22 KiB
C
/* SPDX-License-Identifier: GPL-2.0 OR BSD-3-Clause */
|
|
/*
|
|
* Copyright (C) 2012-2014, 2018-2021 Intel Corporation
|
|
* Copyright (C) 2013-2014 Intel Mobile Communications GmbH
|
|
* Copyright (C) 2015-2016 Intel Deutschland GmbH
|
|
*/
|
|
#ifndef __sta_h__
|
|
#define __sta_h__
|
|
|
|
#include <linux/spinlock.h>
|
|
#include <net/mac80211.h>
|
|
#include <linux/wait.h>
|
|
|
|
#include "iwl-trans.h" /* for IWL_MAX_TID_COUNT */
|
|
#include "fw-api.h" /* IWL_MVM_STATION_COUNT_MAX */
|
|
#include "rs.h"
|
|
|
|
struct iwl_mvm;
|
|
struct iwl_mvm_vif;
|
|
|
|
/**
|
|
* DOC: DQA - Dynamic Queue Allocation -introduction
|
|
*
|
|
* Dynamic Queue Allocation (AKA "DQA") is a feature implemented in iwlwifi
|
|
* driver to allow dynamic allocation of queues on-demand, rather than allocate
|
|
* them statically ahead of time. Ideally, we would like to allocate one queue
|
|
* per RA/TID, thus allowing an AP - for example - to send BE traffic to STA2
|
|
* even if it also needs to send traffic to a sleeping STA1, without being
|
|
* blocked by the sleeping station.
|
|
*
|
|
* Although the queues in DQA mode are dynamically allocated, there are still
|
|
* some queues that are statically allocated:
|
|
* TXQ #0 - command queue
|
|
* TXQ #1 - aux frames
|
|
* TXQ #2 - P2P device frames
|
|
* TXQ #3 - P2P GO/SoftAP GCAST/BCAST frames
|
|
* TXQ #4 - BSS DATA frames queue
|
|
* TXQ #5-8 - Non-QoS and MGMT frames queue pool
|
|
* TXQ #9 - P2P GO/SoftAP probe responses
|
|
* TXQ #10-31 - DATA frames queue pool
|
|
* The queues are dynamically taken from either the MGMT frames queue pool or
|
|
* the DATA frames one. See the %iwl_mvm_dqa_txq for more information on every
|
|
* queue.
|
|
*
|
|
* When a frame for a previously unseen RA/TID comes in, it needs to be deferred
|
|
* until a queue is allocated for it, and only then can be TXed. Therefore, it
|
|
* is placed into %iwl_mvm_tid_data.deferred_tx_frames, and a worker called
|
|
* %mvm->add_stream_wk later allocates the queues and TXes the deferred frames.
|
|
*
|
|
* For convenience, MGMT is considered as if it has TID=8, and go to the MGMT
|
|
* queues in the pool. If there is no longer a free MGMT queue to allocate, a
|
|
* queue will be allocated from the DATA pool instead. Since QoS NDPs can create
|
|
* a problem for aggregations, they too will use a MGMT queue.
|
|
*
|
|
* When adding a STA, a DATA queue is reserved for it so that it can TX from
|
|
* it. If no such free queue exists for reserving, the STA addition will fail.
|
|
*
|
|
* If the DATA queue pool gets exhausted, no new STA will be accepted, and if a
|
|
* new RA/TID comes in for an existing STA, one of the STA's queues will become
|
|
* shared and will serve more than the single TID (but always for the same RA!).
|
|
*
|
|
* When a RA/TID needs to become aggregated, no new queue is required to be
|
|
* allocated, only mark the queue as aggregated via the ADD_STA command. Note,
|
|
* however, that a shared queue cannot be aggregated, and only after the other
|
|
* TIDs become inactive and are removed - only then can the queue be
|
|
* reconfigured and become aggregated.
|
|
*
|
|
* When removing a station, its queues are returned to the pool for reuse. Here
|
|
* we also need to make sure that we are synced with the worker thread that TXes
|
|
* the deferred frames so we don't get into a situation where the queues are
|
|
* removed and then the worker puts deferred frames onto the released queues or
|
|
* tries to allocate new queues for a STA we don't need anymore.
|
|
*/
|
|
|
|
/**
|
|
* DOC: station table - introduction
|
|
*
|
|
* The station table is a list of data structure that reprensent the stations.
|
|
* In STA/P2P client mode, the driver will hold one station for the AP/ GO.
|
|
* In GO/AP mode, the driver will have as many stations as associated clients.
|
|
* All these stations are reflected in the fw's station table. The driver
|
|
* keeps the fw's station table up to date with the ADD_STA command. Stations
|
|
* can be removed by the REMOVE_STA command.
|
|
*
|
|
* All the data related to a station is held in the structure %iwl_mvm_sta
|
|
* which is embed in the mac80211's %ieee80211_sta (in the drv_priv) area.
|
|
* This data includes the index of the station in the fw, per tid information
|
|
* (sequence numbers, Block-ack state machine, etc...). The stations are
|
|
* created and deleted by the %sta_state callback from %ieee80211_ops.
|
|
*
|
|
* The driver holds a map: %fw_id_to_mac_id that allows to fetch a
|
|
* %ieee80211_sta (and the %iwl_mvm_sta embedded into it) based on a fw
|
|
* station index. That way, the driver is able to get the tid related data in
|
|
* O(1) in time sensitive paths (Tx / Tx response / BA notification). These
|
|
* paths are triggered by the fw, and the driver needs to get a pointer to the
|
|
* %ieee80211 structure. This map helps to get that pointer quickly.
|
|
*/
|
|
|
|
/**
|
|
* DOC: station table - locking
|
|
*
|
|
* As stated before, the station is created / deleted by mac80211's %sta_state
|
|
* callback from %ieee80211_ops which can sleep. The next paragraph explains
|
|
* the locking of a single stations, the next ones relates to the station
|
|
* table.
|
|
*
|
|
* The station holds the sequence number per tid. So this data needs to be
|
|
* accessed in the Tx path (which is softIRQ). It also holds the Block-Ack
|
|
* information (the state machine / and the logic that checks if the queues
|
|
* were drained), so it also needs to be accessible from the Tx response flow.
|
|
* In short, the station needs to be access from sleepable context as well as
|
|
* from tasklets, so the station itself needs a spinlock.
|
|
*
|
|
* The writers of %fw_id_to_mac_id map are serialized by the global mutex of
|
|
* the mvm op_mode. This is possible since %sta_state can sleep.
|
|
* The pointers in this map are RCU protected, hence we won't replace the
|
|
* station while we have Tx / Tx response / BA notification running.
|
|
*
|
|
* If a station is deleted while it still has packets in its A-MPDU queues,
|
|
* then the reclaim flow will notice that there is no station in the map for
|
|
* sta_id and it will dump the responses.
|
|
*/
|
|
|
|
/**
|
|
* DOC: station table - internal stations
|
|
*
|
|
* The FW needs a few internal stations that are not reflected in
|
|
* mac80211, such as broadcast station in AP / GO mode, or AUX sta for
|
|
* scanning and P2P device (during the GO negotiation).
|
|
* For these kind of stations we have %iwl_mvm_int_sta struct which holds the
|
|
* data relevant for them from both %iwl_mvm_sta and %ieee80211_sta.
|
|
* Usually the data for these stations is static, so no locking is required,
|
|
* and no TID data as this is also not needed.
|
|
* One thing to note, is that these stations have an ID in the fw, but not
|
|
* in mac80211. In order to "reserve" them a sta_id in %fw_id_to_mac_id
|
|
* we fill ERR_PTR(EINVAL) in this mapping and all other dereferencing of
|
|
* pointers from this mapping need to check that the value is not error
|
|
* or NULL.
|
|
*
|
|
* Currently there is only one auxiliary station for scanning, initialized
|
|
* on init.
|
|
*/
|
|
|
|
/**
|
|
* DOC: station table - AP Station in STA mode
|
|
*
|
|
* %iwl_mvm_vif includes the index of the AP station in the fw's STA table:
|
|
* %ap_sta_id. To get the point to the corresponding %ieee80211_sta,
|
|
* &fw_id_to_mac_id can be used. Due to the way the fw works, we must not remove
|
|
* the AP station from the fw before setting the MAC context as unassociated.
|
|
* Hence, %fw_id_to_mac_id[%ap_sta_id] will be NULLed when the AP station is
|
|
* removed by mac80211, but the station won't be removed in the fw until the
|
|
* VIF is set as unassociated. Then, %ap_sta_id will be invalidated.
|
|
*/
|
|
|
|
/**
|
|
* DOC: station table - Drain vs. Flush
|
|
*
|
|
* Flush means that all the frames in the SCD queue are dumped regardless the
|
|
* station to which they were sent. We do that when we disassociate and before
|
|
* we remove the STA of the AP. The flush can be done synchronously against the
|
|
* fw.
|
|
* Drain means that the fw will drop all the frames sent to a specific station.
|
|
* This is useful when a client (if we are IBSS / GO or AP) disassociates.
|
|
*/
|
|
|
|
/**
|
|
* DOC: station table - fw restart
|
|
*
|
|
* When the fw asserts, or we have any other issue that requires to reset the
|
|
* driver, we require mac80211 to reconfigure the driver. Since the private
|
|
* data of the stations is embed in mac80211's %ieee80211_sta, that data will
|
|
* not be zeroed and needs to be reinitialized manually.
|
|
* %IWL_MVM_STATUS_IN_HW_RESTART is set during restart and that will hint us
|
|
* that we must not allocate a new sta_id but reuse the previous one. This
|
|
* means that the stations being re-added after the reset will have the same
|
|
* place in the fw as before the reset. We do need to zero the %fw_id_to_mac_id
|
|
* map, since the stations aren't in the fw any more. Internal stations that
|
|
* are not added by mac80211 will be re-added in the init flow that is called
|
|
* after the restart: mac80211 call's %iwl_mvm_mac_start which calls to
|
|
* %iwl_mvm_up.
|
|
*/
|
|
|
|
/**
|
|
* DOC: AP mode - PS
|
|
*
|
|
* When a station is asleep, the fw will set it as "asleep". All frames on
|
|
* shared queues (i.e. non-aggregation queues) to that station will be dropped
|
|
* by the fw (%TX_STATUS_FAIL_DEST_PS failure code).
|
|
*
|
|
* AMPDUs are in a separate queue that is stopped by the fw. We just need to
|
|
* let mac80211 know when there are frames in these queues so that it can
|
|
* properly handle trigger frames.
|
|
*
|
|
* When a trigger frame is received, mac80211 tells the driver to send frames
|
|
* from the AMPDU queues or sends frames to non-aggregation queues itself,
|
|
* depending on which ACs are delivery-enabled and what TID has frames to
|
|
* transmit. Note that mac80211 has all the knowledge since all the non-agg
|
|
* frames are buffered / filtered, and the driver tells mac80211 about agg
|
|
* frames). The driver needs to tell the fw to let frames out even if the
|
|
* station is asleep. This is done by %iwl_mvm_sta_modify_sleep_tx_count.
|
|
*
|
|
* When we receive a frame from that station with PM bit unset, the driver
|
|
* needs to let the fw know that this station isn't asleep any more. This is
|
|
* done by %iwl_mvm_sta_modify_ps_wake in response to mac80211 signaling the
|
|
* station's wakeup.
|
|
*
|
|
* For a GO, the Service Period might be cut short due to an absence period
|
|
* of the GO. In this (and all other cases) the firmware notifies us with the
|
|
* EOSP_NOTIFICATION, and we notify mac80211 of that. Further frames that we
|
|
* already sent to the device will be rejected again.
|
|
*
|
|
* See also "AP support for powersaving clients" in mac80211.h.
|
|
*/
|
|
|
|
/**
|
|
* enum iwl_mvm_agg_state
|
|
*
|
|
* The state machine of the BA agreement establishment / tear down.
|
|
* These states relate to a specific RA / TID.
|
|
*
|
|
* @IWL_AGG_OFF: aggregation is not used
|
|
* @IWL_AGG_QUEUED: aggregation start work has been queued
|
|
* @IWL_AGG_STARTING: aggregation are starting (between start and oper)
|
|
* @IWL_AGG_ON: aggregation session is up
|
|
* @IWL_EMPTYING_HW_QUEUE_ADDBA: establishing a BA session - waiting for the
|
|
* HW queue to be empty from packets for this RA /TID.
|
|
* @IWL_EMPTYING_HW_QUEUE_DELBA: tearing down a BA session - waiting for the
|
|
* HW queue to be empty from packets for this RA /TID.
|
|
*/
|
|
enum iwl_mvm_agg_state {
|
|
IWL_AGG_OFF = 0,
|
|
IWL_AGG_QUEUED,
|
|
IWL_AGG_STARTING,
|
|
IWL_AGG_ON,
|
|
IWL_EMPTYING_HW_QUEUE_ADDBA,
|
|
IWL_EMPTYING_HW_QUEUE_DELBA,
|
|
};
|
|
|
|
/**
|
|
* struct iwl_mvm_tid_data - holds the states for each RA / TID
|
|
* @seq_number: the next WiFi sequence number to use
|
|
* @next_reclaimed: the WiFi sequence number of the next packet to be acked.
|
|
* This is basically (last acked packet++).
|
|
* @rate_n_flags: Rate at which Tx was attempted. Holds the data between the
|
|
* Tx response (TX_CMD), and the block ack notification (COMPRESSED_BA).
|
|
* @lq_color: the color of the LQ command as it appears in tx response.
|
|
* @amsdu_in_ampdu_allowed: true if A-MSDU in A-MPDU is allowed.
|
|
* @state: state of the BA agreement establishment / tear down.
|
|
* @txq_id: Tx queue used by the BA session / DQA
|
|
* @ssn: the first packet to be sent in AGG HW queue in Tx AGG start flow, or
|
|
* the first packet to be sent in legacy HW queue in Tx AGG stop flow.
|
|
* Basically when next_reclaimed reaches ssn, we can tell mac80211 that
|
|
* we are ready to finish the Tx AGG stop / start flow.
|
|
* @tx_time: medium time consumed by this A-MPDU
|
|
* @tpt_meas_start: time of the throughput measurements start, is reset every HZ
|
|
* @tx_count_last: number of frames transmitted during the last second
|
|
* @tx_count: counts the number of frames transmitted since the last reset of
|
|
* tpt_meas_start
|
|
*/
|
|
struct iwl_mvm_tid_data {
|
|
u16 seq_number;
|
|
u16 next_reclaimed;
|
|
/* The rest is Tx AGG related */
|
|
u32 rate_n_flags;
|
|
u8 lq_color;
|
|
bool amsdu_in_ampdu_allowed;
|
|
enum iwl_mvm_agg_state state;
|
|
u16 txq_id;
|
|
u16 ssn;
|
|
u16 tx_time;
|
|
unsigned long tpt_meas_start;
|
|
u32 tx_count_last;
|
|
u32 tx_count;
|
|
};
|
|
|
|
struct iwl_mvm_key_pn {
|
|
struct rcu_head rcu_head;
|
|
struct {
|
|
u8 pn[IWL_MAX_TID_COUNT][IEEE80211_CCMP_PN_LEN];
|
|
} ____cacheline_aligned_in_smp q[];
|
|
};
|
|
|
|
/**
|
|
* enum iwl_mvm_rxq_notif_type - Internal message identifier
|
|
*
|
|
* @IWL_MVM_RXQ_EMPTY: empty sync notification
|
|
* @IWL_MVM_RXQ_NOTIF_DEL_BA: notify RSS queues of delBA
|
|
* @IWL_MVM_RXQ_NSSN_SYNC: notify all the RSS queues with the new NSSN
|
|
*/
|
|
enum iwl_mvm_rxq_notif_type {
|
|
IWL_MVM_RXQ_EMPTY,
|
|
IWL_MVM_RXQ_NOTIF_DEL_BA,
|
|
IWL_MVM_RXQ_NSSN_SYNC,
|
|
};
|
|
|
|
/**
|
|
* struct iwl_mvm_internal_rxq_notif - Internal representation of the data sent
|
|
* in &iwl_rxq_sync_cmd. Should be DWORD aligned.
|
|
* FW is agnostic to the payload, so there are no endianity requirements.
|
|
*
|
|
* @type: value from &iwl_mvm_rxq_notif_type
|
|
* @sync: ctrl path is waiting for all notifications to be received
|
|
* @cookie: internal cookie to identify old notifications
|
|
* @data: payload
|
|
*/
|
|
struct iwl_mvm_internal_rxq_notif {
|
|
u16 type;
|
|
u16 sync;
|
|
u32 cookie;
|
|
u8 data[];
|
|
} __packed;
|
|
|
|
struct iwl_mvm_delba_data {
|
|
u32 baid;
|
|
} __packed;
|
|
|
|
struct iwl_mvm_nssn_sync_data {
|
|
u32 baid;
|
|
u32 nssn;
|
|
} __packed;
|
|
|
|
/**
|
|
* struct iwl_mvm_rxq_dup_data - per station per rx queue data
|
|
* @last_seq: last sequence per tid for duplicate packet detection
|
|
* @last_sub_frame: last subframe packet
|
|
*/
|
|
struct iwl_mvm_rxq_dup_data {
|
|
__le16 last_seq[IWL_MAX_TID_COUNT + 1];
|
|
u8 last_sub_frame[IWL_MAX_TID_COUNT + 1];
|
|
} ____cacheline_aligned_in_smp;
|
|
|
|
/**
|
|
* struct iwl_mvm_sta - representation of a station in the driver
|
|
* @sta_id: the index of the station in the fw (will be replaced by id_n_color)
|
|
* @tfd_queue_msk: the tfd queues used by the station
|
|
* @mac_id_n_color: the MAC context this station is linked to
|
|
* @tid_disable_agg: bitmap: if bit(tid) is set, the fw won't send ampdus for
|
|
* tid.
|
|
* @max_agg_bufsize: the maximal size of the AGG buffer for this station
|
|
* @sta_type: station type
|
|
* @sta_state: station state according to enum %ieee80211_sta_state
|
|
* @bt_reduced_txpower: is reduced tx power enabled for this station
|
|
* @next_status_eosp: the next reclaimed packet is a PS-Poll response and
|
|
* we need to signal the EOSP
|
|
* @lock: lock to protect the whole struct. Since %tid_data is access from Tx
|
|
* and from Tx response flow, it needs a spinlock.
|
|
* @tid_data: per tid data + mgmt. Look at %iwl_mvm_tid_data.
|
|
* @tid_to_baid: a simple map of TID to baid
|
|
* @lq_sta: holds rate scaling data, either for the case when RS is done in
|
|
* the driver - %rs_drv or in the FW - %rs_fw.
|
|
* @reserved_queue: the queue reserved for this STA for DQA purposes
|
|
* Every STA has is given one reserved queue to allow it to operate. If no
|
|
* such queue can be guaranteed, the STA addition will fail.
|
|
* @tx_protection: reference counter for controlling the Tx protection.
|
|
* @tt_tx_protection: is thermal throttling enable Tx protection?
|
|
* @disable_tx: is tx to this STA disabled?
|
|
* @amsdu_enabled: bitmap of TX AMSDU allowed TIDs.
|
|
* In case TLC offload is not active it is either 0xFFFF or 0.
|
|
* @max_amsdu_len: max AMSDU length
|
|
* @orig_amsdu_len: used to save the original amsdu_len when it is changed via
|
|
* debugfs. If it's set to 0, it means that it is it's not set via
|
|
* debugfs.
|
|
* @agg_tids: bitmap of tids whose status is operational aggregated (IWL_AGG_ON)
|
|
* @sleep_tx_count: the number of frames that we told the firmware to let out
|
|
* even when that station is asleep. This is useful in case the queue
|
|
* gets empty before all the frames were sent, which can happen when
|
|
* we are sending frames from an AMPDU queue and there was a hole in
|
|
* the BA window. To be used for UAPSD only.
|
|
* @ptk_pn: per-queue PTK PN data structures
|
|
* @dup_data: per queue duplicate packet detection data
|
|
* @deferred_traffic_tid_map: indication bitmap of deferred traffic per-TID
|
|
* @tx_ant: the index of the antenna to use for data tx to this station. Only
|
|
* used during connection establishment (e.g. for the 4 way handshake
|
|
* exchange).
|
|
* @pairwise_cipher: used to feed iwlmei upon authorization
|
|
*
|
|
* When mac80211 creates a station it reserves some space (hw->sta_data_size)
|
|
* in the structure for use by driver. This structure is placed in that
|
|
* space.
|
|
*
|
|
*/
|
|
struct iwl_mvm_sta {
|
|
u32 sta_id;
|
|
u32 tfd_queue_msk;
|
|
u32 mac_id_n_color;
|
|
u16 tid_disable_agg;
|
|
u16 max_agg_bufsize;
|
|
enum iwl_sta_type sta_type;
|
|
enum ieee80211_sta_state sta_state;
|
|
bool bt_reduced_txpower;
|
|
bool next_status_eosp;
|
|
spinlock_t lock;
|
|
struct iwl_mvm_tid_data tid_data[IWL_MAX_TID_COUNT + 1];
|
|
u8 tid_to_baid[IWL_MAX_TID_COUNT];
|
|
union {
|
|
struct iwl_lq_sta_rs_fw rs_fw;
|
|
struct iwl_lq_sta rs_drv;
|
|
} lq_sta;
|
|
struct ieee80211_vif *vif;
|
|
struct iwl_mvm_key_pn __rcu *ptk_pn[4];
|
|
struct iwl_mvm_rxq_dup_data *dup_data;
|
|
|
|
u8 reserved_queue;
|
|
|
|
/* Temporary, until the new TLC will control the Tx protection */
|
|
s8 tx_protection;
|
|
bool tt_tx_protection;
|
|
|
|
bool disable_tx;
|
|
u16 amsdu_enabled;
|
|
u16 max_amsdu_len;
|
|
u16 orig_amsdu_len;
|
|
bool sleeping;
|
|
u8 agg_tids;
|
|
u8 sleep_tx_count;
|
|
u8 avg_energy;
|
|
u8 tx_ant;
|
|
u32 pairwise_cipher;
|
|
};
|
|
|
|
u16 iwl_mvm_tid_queued(struct iwl_mvm *mvm, struct iwl_mvm_tid_data *tid_data);
|
|
|
|
static inline struct iwl_mvm_sta *
|
|
iwl_mvm_sta_from_mac80211(struct ieee80211_sta *sta)
|
|
{
|
|
return (void *)sta->drv_priv;
|
|
}
|
|
|
|
/**
|
|
* struct iwl_mvm_int_sta - representation of an internal station (auxiliary or
|
|
* broadcast)
|
|
* @sta_id: the index of the station in the fw (will be replaced by id_n_color)
|
|
* @type: station type
|
|
* @tfd_queue_msk: the tfd queues used by the station
|
|
*/
|
|
struct iwl_mvm_int_sta {
|
|
u32 sta_id;
|
|
enum iwl_sta_type type;
|
|
u32 tfd_queue_msk;
|
|
};
|
|
|
|
/**
|
|
* Send the STA info to the FW.
|
|
*
|
|
* @mvm: the iwl_mvm* to use
|
|
* @sta: the STA
|
|
* @update: this is true if the FW is being updated about a STA it already knows
|
|
* about. Otherwise (if this is a new STA), this should be false.
|
|
* @flags: if update==true, this marks what is being changed via ORs of values
|
|
* from enum iwl_sta_modify_flag. Otherwise, this is ignored.
|
|
*/
|
|
int iwl_mvm_sta_send_to_fw(struct iwl_mvm *mvm, struct ieee80211_sta *sta,
|
|
bool update, unsigned int flags);
|
|
int iwl_mvm_add_sta(struct iwl_mvm *mvm,
|
|
struct ieee80211_vif *vif,
|
|
struct ieee80211_sta *sta);
|
|
|
|
static inline int iwl_mvm_update_sta(struct iwl_mvm *mvm,
|
|
struct ieee80211_vif *vif,
|
|
struct ieee80211_sta *sta)
|
|
{
|
|
return iwl_mvm_sta_send_to_fw(mvm, sta, true, 0);
|
|
}
|
|
|
|
int iwl_mvm_wait_sta_queues_empty(struct iwl_mvm *mvm,
|
|
struct iwl_mvm_sta *mvm_sta);
|
|
int iwl_mvm_rm_sta(struct iwl_mvm *mvm,
|
|
struct ieee80211_vif *vif,
|
|
struct ieee80211_sta *sta);
|
|
int iwl_mvm_rm_sta_id(struct iwl_mvm *mvm,
|
|
struct ieee80211_vif *vif,
|
|
u8 sta_id);
|
|
int iwl_mvm_set_sta_key(struct iwl_mvm *mvm,
|
|
struct ieee80211_vif *vif,
|
|
struct ieee80211_sta *sta,
|
|
struct ieee80211_key_conf *keyconf,
|
|
u8 key_offset);
|
|
int iwl_mvm_remove_sta_key(struct iwl_mvm *mvm,
|
|
struct ieee80211_vif *vif,
|
|
struct ieee80211_sta *sta,
|
|
struct ieee80211_key_conf *keyconf);
|
|
|
|
void iwl_mvm_update_tkip_key(struct iwl_mvm *mvm,
|
|
struct ieee80211_vif *vif,
|
|
struct ieee80211_key_conf *keyconf,
|
|
struct ieee80211_sta *sta, u32 iv32,
|
|
u16 *phase1key);
|
|
|
|
void iwl_mvm_rx_eosp_notif(struct iwl_mvm *mvm,
|
|
struct iwl_rx_cmd_buffer *rxb);
|
|
|
|
/* AMPDU */
|
|
int iwl_mvm_sta_rx_agg(struct iwl_mvm *mvm, struct ieee80211_sta *sta,
|
|
int tid, u16 ssn, bool start, u16 buf_size, u16 timeout);
|
|
int iwl_mvm_sta_tx_agg_start(struct iwl_mvm *mvm, struct ieee80211_vif *vif,
|
|
struct ieee80211_sta *sta, u16 tid, u16 *ssn);
|
|
int iwl_mvm_sta_tx_agg_oper(struct iwl_mvm *mvm, struct ieee80211_vif *vif,
|
|
struct ieee80211_sta *sta, u16 tid, u16 buf_size,
|
|
bool amsdu);
|
|
int iwl_mvm_sta_tx_agg_stop(struct iwl_mvm *mvm, struct ieee80211_vif *vif,
|
|
struct ieee80211_sta *sta, u16 tid);
|
|
int iwl_mvm_sta_tx_agg_flush(struct iwl_mvm *mvm, struct ieee80211_vif *vif,
|
|
struct ieee80211_sta *sta, u16 tid);
|
|
|
|
int iwl_mvm_sta_tx_agg(struct iwl_mvm *mvm, struct ieee80211_sta *sta,
|
|
int tid, u8 queue, bool start);
|
|
|
|
int iwl_mvm_add_aux_sta(struct iwl_mvm *mvm, u32 lmac_id);
|
|
int iwl_mvm_rm_aux_sta(struct iwl_mvm *mvm);
|
|
|
|
int iwl_mvm_alloc_bcast_sta(struct iwl_mvm *mvm, struct ieee80211_vif *vif);
|
|
int iwl_mvm_send_add_bcast_sta(struct iwl_mvm *mvm, struct ieee80211_vif *vif);
|
|
int iwl_mvm_add_p2p_bcast_sta(struct iwl_mvm *mvm, struct ieee80211_vif *vif);
|
|
int iwl_mvm_send_rm_bcast_sta(struct iwl_mvm *mvm, struct ieee80211_vif *vif);
|
|
int iwl_mvm_rm_p2p_bcast_sta(struct iwl_mvm *mvm, struct ieee80211_vif *vif);
|
|
int iwl_mvm_add_mcast_sta(struct iwl_mvm *mvm, struct ieee80211_vif *vif);
|
|
int iwl_mvm_rm_mcast_sta(struct iwl_mvm *mvm, struct ieee80211_vif *vif);
|
|
int iwl_mvm_allocate_int_sta(struct iwl_mvm *mvm,
|
|
struct iwl_mvm_int_sta *sta,
|
|
u32 qmask, enum nl80211_iftype iftype,
|
|
enum iwl_sta_type type);
|
|
void iwl_mvm_dealloc_bcast_sta(struct iwl_mvm *mvm, struct ieee80211_vif *vif);
|
|
void iwl_mvm_dealloc_int_sta(struct iwl_mvm *mvm, struct iwl_mvm_int_sta *sta);
|
|
int iwl_mvm_add_snif_sta(struct iwl_mvm *mvm, struct ieee80211_vif *vif);
|
|
int iwl_mvm_rm_snif_sta(struct iwl_mvm *mvm, struct ieee80211_vif *vif);
|
|
void iwl_mvm_dealloc_snif_sta(struct iwl_mvm *mvm);
|
|
|
|
void iwl_mvm_sta_modify_ps_wake(struct iwl_mvm *mvm,
|
|
struct ieee80211_sta *sta);
|
|
void iwl_mvm_sta_modify_sleep_tx_count(struct iwl_mvm *mvm,
|
|
struct ieee80211_sta *sta,
|
|
enum ieee80211_frame_release_type reason,
|
|
u16 cnt, u16 tids, bool more_data,
|
|
bool single_sta_queue);
|
|
int iwl_mvm_drain_sta(struct iwl_mvm *mvm, struct iwl_mvm_sta *mvmsta,
|
|
bool drain);
|
|
void iwl_mvm_sta_modify_disable_tx(struct iwl_mvm *mvm,
|
|
struct iwl_mvm_sta *mvmsta, bool disable);
|
|
void iwl_mvm_sta_modify_disable_tx_ap(struct iwl_mvm *mvm,
|
|
struct ieee80211_sta *sta,
|
|
bool disable);
|
|
void iwl_mvm_modify_all_sta_disable_tx(struct iwl_mvm *mvm,
|
|
struct iwl_mvm_vif *mvmvif,
|
|
bool disable);
|
|
void iwl_mvm_csa_client_absent(struct iwl_mvm *mvm, struct ieee80211_vif *vif);
|
|
void iwl_mvm_add_new_dqa_stream_wk(struct work_struct *wk);
|
|
int iwl_mvm_add_pasn_sta(struct iwl_mvm *mvm, struct ieee80211_vif *vif,
|
|
struct iwl_mvm_int_sta *sta, u8 *addr, u32 cipher,
|
|
u8 *key, u32 key_len);
|
|
void iwl_mvm_cancel_channel_switch(struct iwl_mvm *mvm,
|
|
struct ieee80211_vif *vif,
|
|
u32 mac_id);
|
|
#endif /* __sta_h__ */
|