149 lines
3.5 KiB
C
149 lines
3.5 KiB
C
/* SPDX-License-Identifier: GPL-2.0 */
|
|
/*
|
|
* This is used to for host and peripheral modes of the driver for
|
|
* Inventra (Multidrop) Highspeed Dual-Role Controllers: (M)HDRC.
|
|
*
|
|
* Board initialization should put one of these into dev->platform_data,
|
|
* probably on some platform_device named "musb-hdrc". It encapsulates
|
|
* key configuration differences between boards.
|
|
*/
|
|
|
|
#ifndef __LINUX_USB_MUSB_H
|
|
#define __LINUX_USB_MUSB_H
|
|
|
|
/* The USB role is defined by the connector used on the board, so long as
|
|
* standards are being followed. (Developer boards sometimes won't.)
|
|
*/
|
|
enum musb_mode {
|
|
MUSB_UNDEFINED = 0,
|
|
MUSB_HOST, /* A or Mini-A connector */
|
|
MUSB_PERIPHERAL, /* B or Mini-B connector */
|
|
MUSB_OTG /* Mini-AB connector */
|
|
};
|
|
|
|
struct clk;
|
|
|
|
enum musb_fifo_style {
|
|
FIFO_RXTX,
|
|
FIFO_TX,
|
|
FIFO_RX
|
|
} __attribute__ ((packed));
|
|
|
|
enum musb_buf_mode {
|
|
BUF_SINGLE,
|
|
BUF_DOUBLE
|
|
} __attribute__ ((packed));
|
|
|
|
struct musb_fifo_cfg {
|
|
u8 hw_ep_num;
|
|
enum musb_fifo_style style;
|
|
enum musb_buf_mode mode;
|
|
u16 maxpacket;
|
|
};
|
|
|
|
#define MUSB_EP_FIFO(ep, st, m, pkt) \
|
|
{ \
|
|
.hw_ep_num = ep, \
|
|
.style = st, \
|
|
.mode = m, \
|
|
.maxpacket = pkt, \
|
|
}
|
|
|
|
#define MUSB_EP_FIFO_SINGLE(ep, st, pkt) \
|
|
MUSB_EP_FIFO(ep, st, BUF_SINGLE, pkt)
|
|
|
|
#define MUSB_EP_FIFO_DOUBLE(ep, st, pkt) \
|
|
MUSB_EP_FIFO(ep, st, BUF_DOUBLE, pkt)
|
|
|
|
struct musb_hdrc_eps_bits {
|
|
const char name[16];
|
|
u8 bits;
|
|
};
|
|
|
|
struct musb_hdrc_config {
|
|
struct musb_fifo_cfg *fifo_cfg; /* board fifo configuration */
|
|
unsigned fifo_cfg_size; /* size of the fifo configuration */
|
|
|
|
/* MUSB configuration-specific details */
|
|
unsigned multipoint:1; /* multipoint device */
|
|
unsigned dyn_fifo:1 __deprecated; /* supports dynamic fifo sizing */
|
|
|
|
/* need to explicitly de-assert the port reset after resume? */
|
|
unsigned host_port_deassert_reset_at_resume:1;
|
|
|
|
u8 num_eps; /* number of endpoints _with_ ep0 */
|
|
u8 ram_bits; /* ram address size */
|
|
|
|
u32 maximum_speed;
|
|
};
|
|
|
|
struct musb_hdrc_platform_data {
|
|
/* MUSB_HOST, MUSB_PERIPHERAL, or MUSB_OTG */
|
|
u8 mode;
|
|
|
|
/* for clk_get() */
|
|
const char *clock;
|
|
|
|
/* (HOST or OTG) switch VBUS on/off */
|
|
int (*set_vbus)(struct device *dev, int is_on);
|
|
|
|
/* (HOST or OTG) mA/2 power supplied on (default = 8mA) */
|
|
u8 power;
|
|
|
|
/* (PERIPHERAL) mA/2 max power consumed (default = 100mA) */
|
|
u8 min_power;
|
|
|
|
/* (HOST or OTG) msec/2 after VBUS on till power good */
|
|
u8 potpgt;
|
|
|
|
/* (HOST or OTG) program PHY for external Vbus */
|
|
unsigned extvbus:1;
|
|
|
|
/* Power the device on or off */
|
|
int (*set_power)(int state);
|
|
|
|
/* MUSB configuration-specific details */
|
|
const struct musb_hdrc_config *config;
|
|
|
|
/* Architecture specific board data */
|
|
void *board_data;
|
|
|
|
/* Platform specific struct musb_ops pointer */
|
|
const void *platform_ops;
|
|
};
|
|
|
|
enum musb_vbus_id_status {
|
|
MUSB_UNKNOWN = 0,
|
|
MUSB_ID_GROUND,
|
|
MUSB_ID_FLOAT,
|
|
MUSB_VBUS_VALID,
|
|
MUSB_VBUS_OFF,
|
|
};
|
|
|
|
#if IS_ENABLED(CONFIG_USB_MUSB_HDRC)
|
|
int musb_mailbox(enum musb_vbus_id_status status);
|
|
#else
|
|
static inline int musb_mailbox(enum musb_vbus_id_status status)
|
|
{
|
|
return 0;
|
|
}
|
|
#endif
|
|
|
|
/* TUSB 6010 support */
|
|
|
|
#define TUSB6010_OSCCLK_60 16667 /* psec/clk @ 60.0 MHz */
|
|
#define TUSB6010_REFCLK_24 41667 /* psec/clk @ 24.0 MHz XI */
|
|
#define TUSB6010_REFCLK_19 52083 /* psec/clk @ 19.2 MHz CLKIN */
|
|
|
|
#ifdef CONFIG_ARCH_OMAP2
|
|
|
|
extern int __init tusb6010_setup_interface(
|
|
struct musb_hdrc_platform_data *data,
|
|
unsigned ps_refclk, unsigned waitpin,
|
|
unsigned async_cs, unsigned sync_cs,
|
|
unsigned irq, unsigned dmachan);
|
|
|
|
#endif /* OMAP2 */
|
|
|
|
#endif /* __LINUX_USB_MUSB_H */
|