478 lines
11 KiB
Plaintext
478 lines
11 KiB
Plaintext
|
// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
|
||
|
|
/*
|
||
|
|
* Copyright 2018 Bang & Olufsen
|
||
|
|
*/
|
||
|
|
|
||
|
|
#include "imx8mm.dtsi"
|
||
|
|
#include <dt-bindings/phy/phy-imx8-pcie.h>
|
||
|
|
|
||
|
|
/ {
|
||
|
|
reg_modem: regulator-modem {
|
||
|
|
compatible = "regulator-fixed";
|
||
|
|
pinctrl-names = "default";
|
||
|
|
pinctrl-0 = <&pinctrl_modem_regulator>;
|
||
|
|
regulator-min-microvolt = <3300000>;
|
||
|
|
regulator-max-microvolt = <3300000>;
|
||
|
|
regulator-name = "epdev_on";
|
||
|
|
gpio = <&gpio3 16 GPIO_ACTIVE_HIGH>;
|
||
|
|
enable-active-high;
|
||
|
|
regulator-always-on;
|
||
|
|
};
|
||
|
|
|
||
|
|
reg_3v3_out: regulator-3v3-out {
|
||
|
|
compatible = "regulator-fixed";
|
||
|
|
regulator-name = "3V3_OUT";
|
||
|
|
regulator-min-microvolt = <3300000>;
|
||
|
|
regulator-max-microvolt = <3300000>;
|
||
|
|
};
|
||
|
|
};
|
||
|
|
|
||
|
|
&cpu_alert0 {
|
||
|
|
temperature = <95000>;
|
||
|
|
};
|
||
|
|
|
||
|
|
&cpu_crit0 {
|
||
|
|
temperature = <105000>;
|
||
|
|
};
|
||
|
|
|
||
|
|
&ddrc {
|
||
|
|
operating-points-v2 = <&ddrc_opp_table>;
|
||
|
|
|
||
|
|
ddrc_opp_table: opp-table {
|
||
|
|
compatible = "operating-points-v2";
|
||
|
|
|
||
|
|
opp-25000000 {
|
||
|
|
opp-hz = /bits/ 64 <25000000>;
|
||
|
|
};
|
||
|
|
|
||
|
|
opp-100000000 {
|
||
|
|
opp-hz = /bits/ 64 <100000000>;
|
||
|
|
};
|
||
|
|
|
||
|
|
opp-600000000 {
|
||
|
|
opp-hz = /bits/ 64 <600000000>;
|
||
|
|
};
|
||
|
|
};
|
||
|
|
};
|
||
|
|
|
||
|
|
&i2c1 {
|
||
|
|
clock-frequency = <100000>;
|
||
|
|
pinctrl-names = "default", "gpio";
|
||
|
|
pinctrl-0 = <&pinctrl_i2c1>;
|
||
|
|
pinctrl-1 = <&pinctrl_i2c1_gpio>;
|
||
|
|
scl-gpios = <&gpio5 14 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
|
||
|
|
sda-gpios = <&gpio5 15 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
|
||
|
|
status = "okay";
|
||
|
|
|
||
|
|
pmic@4b {
|
||
|
|
compatible = "rohm,bd71847";
|
||
|
|
reg = <0x4b>;
|
||
|
|
pinctrl-0 = <&pinctrl_pmic>;
|
||
|
|
interrupt-parent = <&gpio1>;
|
||
|
|
interrupts = <3 IRQ_TYPE_LEVEL_LOW>;
|
||
|
|
rohm,reset-snvs-powered;
|
||
|
|
|
||
|
|
regulators {
|
||
|
|
buck1_reg: BUCK1 {
|
||
|
|
regulator-name = "buck1";
|
||
|
|
regulator-min-microvolt = <700000>;
|
||
|
|
regulator-max-microvolt = <1300000>;
|
||
|
|
regulator-boot-on;
|
||
|
|
regulator-always-on;
|
||
|
|
regulator-ramp-delay = <1250>;
|
||
|
|
rohm,dvs-run-voltage = <850000>;
|
||
|
|
rohm,dvs-idle-voltage = <850000>;
|
||
|
|
rohm,dvs-suspend-voltage = <850000>;
|
||
|
|
};
|
||
|
|
|
||
|
|
buck2_reg: BUCK2 {
|
||
|
|
regulator-name = "buck2";
|
||
|
|
regulator-min-microvolt = <700000>;
|
||
|
|
regulator-max-microvolt = <1300000>;
|
||
|
|
regulator-boot-on;
|
||
|
|
regulator-always-on;
|
||
|
|
regulator-ramp-delay = <1250>;
|
||
|
|
rohm,dvs-run-voltage = <1000000>;
|
||
|
|
rohm,dvs-idle-voltage = <900000>;
|
||
|
|
};
|
||
|
|
|
||
|
|
buck3_reg: BUCK3 {
|
||
|
|
// buck5 in datasheet
|
||
|
|
regulator-name = "buck3";
|
||
|
|
regulator-min-microvolt = <700000>;
|
||
|
|
regulator-max-microvolt = <1350000>;
|
||
|
|
regulator-boot-on;
|
||
|
|
regulator-always-on;
|
||
|
|
};
|
||
|
|
|
||
|
|
buck4_reg: BUCK4 {
|
||
|
|
// buck6 in datasheet
|
||
|
|
regulator-name = "buck4";
|
||
|
|
regulator-min-microvolt = <3000000>;
|
||
|
|
regulator-max-microvolt = <3300000>;
|
||
|
|
regulator-boot-on;
|
||
|
|
regulator-always-on;
|
||
|
|
};
|
||
|
|
|
||
|
|
buck5_reg: BUCK5 {
|
||
|
|
// buck7 in datasheet
|
||
|
|
regulator-name = "buck5";
|
||
|
|
regulator-min-microvolt = <1605000>;
|
||
|
|
regulator-max-microvolt = <1995000>;
|
||
|
|
regulator-boot-on;
|
||
|
|
regulator-always-on;
|
||
|
|
};
|
||
|
|
|
||
|
|
buck6_reg: BUCK6 {
|
||
|
|
// buck8 in datasheet
|
||
|
|
regulator-name = "buck6";
|
||
|
|
regulator-min-microvolt = <800000>;
|
||
|
|
regulator-max-microvolt = <1400000>;
|
||
|
|
regulator-boot-on;
|
||
|
|
regulator-always-on;
|
||
|
|
};
|
||
|
|
|
||
|
|
ldo1_reg: LDO1 {
|
||
|
|
regulator-name = "ldo1";
|
||
|
|
regulator-min-microvolt = <1800000>;
|
||
|
|
regulator-max-microvolt = <3300000>;
|
||
|
|
regulator-boot-on;
|
||
|
|
regulator-always-on;
|
||
|
|
};
|
||
|
|
|
||
|
|
ldo2_reg: LDO2 {
|
||
|
|
regulator-name = "ldo2";
|
||
|
|
regulator-min-microvolt = <800000>;
|
||
|
|
regulator-max-microvolt = <900000>;
|
||
|
|
regulator-boot-on;
|
||
|
|
regulator-always-on;
|
||
|
|
};
|
||
|
|
|
||
|
|
ldo3_reg: LDO3 {
|
||
|
|
regulator-name = "ldo3";
|
||
|
|
regulator-min-microvolt = <1800000>;
|
||
|
|
regulator-max-microvolt = <3300000>;
|
||
|
|
regulator-boot-on;
|
||
|
|
regulator-always-on;
|
||
|
|
};
|
||
|
|
|
||
|
|
ldo4_reg: LDO4 {
|
||
|
|
regulator-name = "ldo4";
|
||
|
|
regulator-min-microvolt = <900000>;
|
||
|
|
regulator-max-microvolt = <1800000>;
|
||
|
|
regulator-boot-on;
|
||
|
|
regulator-always-on;
|
||
|
|
};
|
||
|
|
|
||
|
|
ldo5_reg: LDO5 {
|
||
|
|
regulator-name = "ldo5";
|
||
|
|
regulator-min-microvolt = <1800000>;
|
||
|
|
regulator-max-microvolt = <3300000>;
|
||
|
|
};
|
||
|
|
|
||
|
|
ldo6_reg: LDO6 {
|
||
|
|
regulator-name = "ldo6";
|
||
|
|
regulator-min-microvolt = <900000>;
|
||
|
|
regulator-max-microvolt = <1800000>;
|
||
|
|
regulator-boot-on;
|
||
|
|
regulator-always-on;
|
||
|
|
};
|
||
|
|
};
|
||
|
|
};
|
||
|
|
};
|
||
|
|
|
||
|
|
&i2c2 {
|
||
|
|
clock-frequency = <100000>;
|
||
|
|
pinctrl-names = "default", "gpio";
|
||
|
|
pinctrl-0 = <&pinctrl_i2c2>;
|
||
|
|
pinctrl-1 = <&pinctrl_i2c2_gpio>;
|
||
|
|
scl-gpios = <&gpio5 16 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
|
||
|
|
sda-gpios = <&gpio5 17 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
|
||
|
|
status = "okay";
|
||
|
|
};
|
||
|
|
|
||
|
|
&i2c3 {
|
||
|
|
pinctrl-names = "default", "gpio";
|
||
|
|
pinctrl-0 = <&pinctrl_i2c3>;
|
||
|
|
pinctrl-1 = <&pinctrl_i2c3_gpio>;
|
||
|
|
scl-gpios = <&gpio5 18 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
|
||
|
|
sda-gpios = <&gpio5 19 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
|
||
|
|
};
|
||
|
|
|
||
|
|
&pcie_phy {
|
||
|
|
fsl,refclk-pad-mode = <IMX8_PCIE_REFCLK_PAD_OUTPUT>;
|
||
|
|
fsl,tx-deemph-gen1 = <0x2d>;
|
||
|
|
fsl,tx-deemph-gen2 = <0xf>;
|
||
|
|
status = "okay";
|
||
|
|
};
|
||
|
|
|
||
|
|
&pcie0 {
|
||
|
|
pinctrl-names = "default";
|
||
|
|
pinctrl-0 = <&pinctrl_pcie0>;
|
||
|
|
reset-gpio = <&gpio5 21 GPIO_ACTIVE_LOW>;
|
||
|
|
fsl,max-link-speed = <1>;
|
||
|
|
assigned-clocks = <&clk IMX8MM_CLK_PCIE1_AUX>, <&clk IMX8MM_CLK_PCIE1_CTRL>;
|
||
|
|
assigned-clock-rates = <10000000>, <250000000>;
|
||
|
|
assigned-clock-parents = <&clk IMX8MM_SYS_PLL2_50M>, <&clk IMX8MM_SYS_PLL2_250M>;
|
||
|
|
status = "okay";
|
||
|
|
};
|
||
|
|
|
||
|
|
&uart1 { /* BT */
|
||
|
|
pinctrl-names = "default";
|
||
|
|
pinctrl-0 = <&pinctrl_uart1>;
|
||
|
|
assigned-clocks = <&clk IMX8MM_CLK_UART1>;
|
||
|
|
assigned-clock-parents = <&clk IMX8MM_SYS_PLL1_80M>;
|
||
|
|
uart-has-rtscts;
|
||
|
|
status = "okay";
|
||
|
|
|
||
|
|
bluetooth {
|
||
|
|
compatible = "brcm,bcm4349-bt";
|
||
|
|
pinctrl-names = "default";
|
||
|
|
pinctrl-0 = <&pinctrl_modem_bt>;
|
||
|
|
device-wakeup-gpios = <&gpio3 3 GPIO_ACTIVE_HIGH>;
|
||
|
|
host-wakeup-gpios = <&gpio3 4 GPIO_ACTIVE_HIGH>;
|
||
|
|
shutdown-gpios = <&gpio3 15 GPIO_ACTIVE_HIGH>;
|
||
|
|
vbat-supply = <®_3v3_out>;
|
||
|
|
vddio-supply = <®_3v3_out>;
|
||
|
|
clocks = <&osc_32k>;
|
||
|
|
max-speed = <3000000>;
|
||
|
|
clock-names = "extclk";
|
||
|
|
};
|
||
|
|
};
|
||
|
|
|
||
|
|
&uart2 { /* console */
|
||
|
|
pinctrl-names = "default";
|
||
|
|
pinctrl-0 = <&pinctrl_uart2>;
|
||
|
|
};
|
||
|
|
|
||
|
|
&usdhc1 {
|
||
|
|
pinctrl-names = "default";
|
||
|
|
pinctrl-0 = <&pinctrl_usdhc1>;
|
||
|
|
bus-width = <8>;
|
||
|
|
no-sd;
|
||
|
|
no-sdio;
|
||
|
|
non-removable;
|
||
|
|
status = "okay";
|
||
|
|
};
|
||
|
|
|
||
|
|
&usdhc2 {
|
||
|
|
pinctrl-names = "default", "state_100mhz", "state_200mhz";
|
||
|
|
pinctrl-0 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_gpio>;
|
||
|
|
pinctrl-1 = <&pinctrl_usdhc2_100mhz>, <&pinctrl_usdhc2_gpio>;
|
||
|
|
pinctrl-2 = <&pinctrl_usdhc2_200mhz>, <&pinctrl_usdhc2_gpio>;
|
||
|
|
bus-width = <4>;
|
||
|
|
};
|
||
|
|
|
||
|
|
&wdog1 {
|
||
|
|
pinctrl-names = "default";
|
||
|
|
pinctrl-0 = <&pinctrl_wdog>;
|
||
|
|
fsl,ext-reset-output;
|
||
|
|
status = "okay";
|
||
|
|
};
|
||
|
|
|
||
|
|
&A53_0 {
|
||
|
|
cpu-supply = <&buck2_reg>;
|
||
|
|
};
|
||
|
|
|
||
|
|
&A53_1 {
|
||
|
|
cpu-supply = <&buck2_reg>;
|
||
|
|
};
|
||
|
|
|
||
|
|
&A53_2 {
|
||
|
|
cpu-supply = <&buck2_reg>;
|
||
|
|
};
|
||
|
|
|
||
|
|
&A53_3 {
|
||
|
|
cpu-supply = <&buck2_reg>;
|
||
|
|
};
|
||
|
|
|
||
|
|
/delete-node/ &sec_jr1; /* Job ring in use by OP-TEE */
|
||
|
|
|
||
|
|
&iomuxc {
|
||
|
|
pinctrl_i2c1: i2c1-grp {
|
||
|
|
fsl,pins = <
|
||
|
|
MX8MM_IOMUXC_I2C1_SCL_I2C1_SCL 0x400001c3
|
||
|
|
MX8MM_IOMUXC_I2C1_SDA_I2C1_SDA 0x400001c3
|
||
|
|
>;
|
||
|
|
};
|
||
|
|
|
||
|
|
pinctrl_i2c1_gpio: i2c1-gpio-grp {
|
||
|
|
fsl,pins = <
|
||
|
|
MX8MM_IOMUXC_I2C1_SCL_GPIO5_IO14 0x400001c3
|
||
|
|
MX8MM_IOMUXC_I2C1_SDA_GPIO5_IO15 0x400001c3
|
||
|
|
>;
|
||
|
|
};
|
||
|
|
|
||
|
|
pinctrl_i2c2: i2c2-grp {
|
||
|
|
fsl,pins = <
|
||
|
|
MX8MM_IOMUXC_I2C2_SCL_I2C2_SCL 0x400001c3
|
||
|
|
MX8MM_IOMUXC_I2C2_SDA_I2C2_SDA 0x400001c3
|
||
|
|
>;
|
||
|
|
};
|
||
|
|
|
||
|
|
pinctrl_i2c2_gpio: i2c2-gpio-grp {
|
||
|
|
fsl,pins = <
|
||
|
|
MX8MM_IOMUXC_I2C2_SCL_GPIO5_IO16 0x400001c3
|
||
|
|
MX8MM_IOMUXC_I2C2_SDA_GPIO5_IO17 0x400001c3
|
||
|
|
>;
|
||
|
|
};
|
||
|
|
|
||
|
|
pinctrl_i2c3: i2c3-grp {
|
||
|
|
fsl,pins = <
|
||
|
|
MX8MM_IOMUXC_I2C3_SCL_I2C3_SCL 0x400001c3
|
||
|
|
MX8MM_IOMUXC_I2C3_SDA_I2C3_SDA 0x400001c3
|
||
|
|
>;
|
||
|
|
};
|
||
|
|
|
||
|
|
pinctrl_i2c3_gpio: i2c3-gpio-grp {
|
||
|
|
fsl,pins = <
|
||
|
|
MX8MM_IOMUXC_I2C3_SCL_GPIO5_IO18 0x400001c3
|
||
|
|
MX8MM_IOMUXC_I2C3_SDA_GPIO5_IO19 0x400001c3
|
||
|
|
>;
|
||
|
|
};
|
||
|
|
|
||
|
|
pinctrl_pcie0: pcie0-grp {
|
||
|
|
fsl,pins = <
|
||
|
|
MX8MM_IOMUXC_I2C4_SCL_PCIE1_CLKREQ_B 0x61
|
||
|
|
MX8MM_IOMUXC_I2C4_SDA_GPIO5_IO21 0x6
|
||
|
|
>;
|
||
|
|
};
|
||
|
|
|
||
|
|
pinctrl_modem_bt: modem-bt-grp {
|
||
|
|
fsl,pins = <
|
||
|
|
MX8MM_IOMUXC_NAND_CLE_GPIO3_IO5 0x19
|
||
|
|
MX8MM_IOMUXC_NAND_CE2_B_GPIO3_IO3 0x19
|
||
|
|
MX8MM_IOMUXC_NAND_CE3_B_GPIO3_IO4 0x19
|
||
|
|
MX8MM_IOMUXC_NAND_RE_B_GPIO3_IO15 0x19
|
||
|
|
MX8MM_IOMUXC_GPIO1_IO00_ANAMIX_REF_CLK_32K 0x141
|
||
|
|
>;
|
||
|
|
};
|
||
|
|
|
||
|
|
pinctrl_modem_regulator: modem-reg-grp {
|
||
|
|
fsl,pins = <
|
||
|
|
MX8MM_IOMUXC_NAND_READY_B_GPIO3_IO16 0x41
|
||
|
|
>;
|
||
|
|
};
|
||
|
|
|
||
|
|
pinctrl_pmic: pmic-irq-grp {
|
||
|
|
fsl,pins = <
|
||
|
|
MX8MM_IOMUXC_GPIO1_IO03_GPIO1_IO3 0x41
|
||
|
|
>;
|
||
|
|
};
|
||
|
|
|
||
|
|
pinctrl_uart1: uart1-grp {
|
||
|
|
fsl,pins = <
|
||
|
|
MX8MM_IOMUXC_UART1_RXD_UART1_DCE_RX 0x140
|
||
|
|
MX8MM_IOMUXC_UART1_TXD_UART1_DCE_TX 0x140
|
||
|
|
MX8MM_IOMUXC_UART3_RXD_UART1_DCE_CTS_B 0x140
|
||
|
|
MX8MM_IOMUXC_UART3_TXD_UART1_DCE_RTS_B 0x140
|
||
|
|
>;
|
||
|
|
};
|
||
|
|
|
||
|
|
pinctrl_uart2: uart2-grp {
|
||
|
|
fsl,pins = <
|
||
|
|
MX8MM_IOMUXC_UART2_RXD_UART2_DCE_RX 0x140
|
||
|
|
MX8MM_IOMUXC_UART2_TXD_UART2_DCE_TX 0x140
|
||
|
|
>;
|
||
|
|
};
|
||
|
|
|
||
|
|
pinctrl_usdhc1: usdhc1-grp {
|
||
|
|
fsl,pins = <
|
||
|
|
MX8MM_IOMUXC_SD1_CLK_USDHC1_CLK 0x40000190
|
||
|
|
MX8MM_IOMUXC_SD1_CMD_USDHC1_CMD 0x1d0
|
||
|
|
MX8MM_IOMUXC_SD1_DATA0_USDHC1_DATA0 0x1d0
|
||
|
|
MX8MM_IOMUXC_SD1_DATA1_USDHC1_DATA1 0x1d0
|
||
|
|
MX8MM_IOMUXC_SD1_DATA2_USDHC1_DATA2 0x1d0
|
||
|
|
MX8MM_IOMUXC_SD1_DATA3_USDHC1_DATA3 0x1d0
|
||
|
|
MX8MM_IOMUXC_SD1_DATA4_USDHC1_DATA4 0x1d0
|
||
|
|
MX8MM_IOMUXC_SD1_DATA5_USDHC1_DATA5 0x1d0
|
||
|
|
MX8MM_IOMUXC_SD1_DATA6_USDHC1_DATA6 0x1d0
|
||
|
|
MX8MM_IOMUXC_SD1_DATA7_USDHC1_DATA7 0x1d0
|
||
|
|
MX8MM_IOMUXC_SD1_STROBE_USDHC1_STROBE 0x190
|
||
|
|
MX8MM_IOMUXC_SD1_RESET_B_USDHC1_RESET_B 0x1d0
|
||
|
|
>;
|
||
|
|
};
|
||
|
|
|
||
|
|
pinctrl_usdhc1_100mhz: usdhc1-100mhz-grp {
|
||
|
|
fsl,pins = <
|
||
|
|
MX8MM_IOMUXC_SD1_CLK_USDHC1_CLK 0x40000194
|
||
|
|
MX8MM_IOMUXC_SD1_CMD_USDHC1_CMD 0x1d4
|
||
|
|
MX8MM_IOMUXC_SD1_DATA0_USDHC1_DATA0 0x1d4
|
||
|
|
MX8MM_IOMUXC_SD1_DATA1_USDHC1_DATA1 0x1d4
|
||
|
|
MX8MM_IOMUXC_SD1_DATA2_USDHC1_DATA2 0x1d4
|
||
|
|
MX8MM_IOMUXC_SD1_DATA3_USDHC1_DATA3 0x1d4
|
||
|
|
MX8MM_IOMUXC_SD1_DATA4_USDHC1_DATA4 0x1d4
|
||
|
|
MX8MM_IOMUXC_SD1_DATA5_USDHC1_DATA5 0x1d4
|
||
|
|
MX8MM_IOMUXC_SD1_DATA6_USDHC1_DATA6 0x1d4
|
||
|
|
MX8MM_IOMUXC_SD1_DATA7_USDHC1_DATA7 0x1d4
|
||
|
|
MX8MM_IOMUXC_SD1_STROBE_USDHC1_STROBE 0x194
|
||
|
|
MX8MM_IOMUXC_SD1_RESET_B_USDHC1_RESET_B 0x1d4
|
||
|
|
>;
|
||
|
|
};
|
||
|
|
|
||
|
|
pinctrl_usdhc1_200mhz: usdhc1-200mhz-grp {
|
||
|
|
fsl,pins = <
|
||
|
|
MX8MM_IOMUXC_SD1_CLK_USDHC1_CLK 0x40000196
|
||
|
|
MX8MM_IOMUXC_SD1_CMD_USDHC1_CMD 0x1d6
|
||
|
|
MX8MM_IOMUXC_SD1_DATA0_USDHC1_DATA0 0x1d6
|
||
|
|
MX8MM_IOMUXC_SD1_DATA1_USDHC1_DATA1 0x1d6
|
||
|
|
MX8MM_IOMUXC_SD1_DATA2_USDHC1_DATA2 0x1d6
|
||
|
|
MX8MM_IOMUXC_SD1_DATA3_USDHC1_DATA3 0x1d6
|
||
|
|
MX8MM_IOMUXC_SD1_DATA4_USDHC1_DATA4 0x1d6
|
||
|
|
MX8MM_IOMUXC_SD1_DATA5_USDHC1_DATA5 0x1d6
|
||
|
|
MX8MM_IOMUXC_SD1_DATA6_USDHC1_DATA6 0x1d6
|
||
|
|
MX8MM_IOMUXC_SD1_DATA7_USDHC1_DATA7 0x1d6
|
||
|
|
MX8MM_IOMUXC_SD1_STROBE_USDHC1_STROBE 0x196
|
||
|
|
MX8MM_IOMUXC_SD1_RESET_B_USDHC1_RESET_B 0x1d6
|
||
|
|
>;
|
||
|
|
};
|
||
|
|
|
||
|
|
pinctrl_usdhc2_gpio: usdhc2-gpio-grp {
|
||
|
|
fsl,pins = <
|
||
|
|
MX8MM_IOMUXC_SD2_RESET_B_GPIO2_IO19 0x1d0
|
||
|
|
>;
|
||
|
|
};
|
||
|
|
|
||
|
|
pinctrl_usdhc2: usdhc2-grp {
|
||
|
|
fsl,pins = <
|
||
|
|
MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK 0x190
|
||
|
|
MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d0
|
||
|
|
MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d0
|
||
|
|
MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d0
|
||
|
|
MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d0
|
||
|
|
MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d0
|
||
|
|
MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x1d0
|
||
|
|
>;
|
||
|
|
};
|
||
|
|
|
||
|
|
pinctrl_usdhc2_100mhz: usdhc2-100mhz-grp {
|
||
|
|
fsl,pins = <
|
||
|
|
MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK 0x194
|
||
|
|
MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d4
|
||
|
|
MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d4
|
||
|
|
MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d4
|
||
|
|
MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d4
|
||
|
|
MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d4
|
||
|
|
MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x1d0
|
||
|
|
>;
|
||
|
|
};
|
||
|
|
|
||
|
|
pinctrl_usdhc2_200mhz: usdhc2-200mhz-grp {
|
||
|
|
fsl,pins = <
|
||
|
|
MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK 0x196
|
||
|
|
MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d6
|
||
|
|
MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d6
|
||
|
|
MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d6
|
||
|
|
MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d6
|
||
|
|
MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d6
|
||
|
|
MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x1d0
|
||
|
|
>;
|
||
|
|
};
|
||
|
|
|
||
|
|
pinctrl_wdog: wdog-grp {
|
||
|
|
fsl,pins = <
|
||
|
|
MX8MM_IOMUXC_GPIO1_IO02_WDOG1_WDOG_B 0xc6
|
||
|
|
>;
|
||
|
|
};
|
||
|
|
};
|