461 lines
15 KiB
YAML
461 lines
15 KiB
YAML
|
# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
|
||
|
|
%YAML 1.2
|
||
|
|
---
|
||
|
|
$id: http://devicetree.org/schemas/pinctrl/mediatek,mt7986-pinctrl.yaml#
|
||
|
|
$schema: http://devicetree.org/meta-schemas/core.yaml#
|
||
|
|
|
||
|
|
title: Mediatek MT7986 Pin Controller
|
||
|
|
|
||
|
|
maintainers:
|
||
|
|
- Sean Wang <sean.wang@kernel.org>
|
||
|
|
|
||
|
|
description: |+
|
||
|
|
The MediaTek's MT7986 Pin controller is used to control SoC pins.
|
||
|
|
|
||
|
|
properties:
|
||
|
|
compatible:
|
||
|
|
enum:
|
||
|
|
- mediatek,mt7986a-pinctrl
|
||
|
|
- mediatek,mt7986b-pinctrl
|
||
|
|
|
||
|
|
reg:
|
||
|
|
minItems: 8
|
||
|
|
maxItems: 8
|
||
|
|
|
||
|
|
reg-names:
|
||
|
|
items:
|
||
|
|
- const: gpio
|
||
|
|
- const: iocfg_rt
|
||
|
|
- const: iocfg_rb
|
||
|
|
- const: iocfg_lt
|
||
|
|
- const: iocfg_lb
|
||
|
|
- const: iocfg_tr
|
||
|
|
- const: iocfg_tl
|
||
|
|
- const: eint
|
||
|
|
|
||
|
|
gpio-controller: true
|
||
|
|
|
||
|
|
"#gpio-cells":
|
||
|
|
const: 2
|
||
|
|
description: |
|
||
|
|
Number of cells in GPIO specifier. Since the generic GPIO
|
||
|
|
binding is used, the amount of cells must be specified as 2. See the below
|
||
|
|
mentioned gpio binding representation for description of particular cells.
|
||
|
|
|
||
|
|
gpio-ranges:
|
||
|
|
minItems: 1
|
||
|
|
maxItems: 5
|
||
|
|
description: |
|
||
|
|
GPIO valid number range.
|
||
|
|
|
||
|
|
interrupt-controller: true
|
||
|
|
|
||
|
|
interrupts:
|
||
|
|
maxItems: 1
|
||
|
|
|
||
|
|
"#interrupt-cells":
|
||
|
|
const: 2
|
||
|
|
|
||
|
|
allOf:
|
||
|
|
- $ref: "pinctrl.yaml#"
|
||
|
|
|
||
|
|
required:
|
||
|
|
- compatible
|
||
|
|
- reg
|
||
|
|
- reg-names
|
||
|
|
- gpio-controller
|
||
|
|
- "#gpio-cells"
|
||
|
|
|
||
|
|
patternProperties:
|
||
|
|
'-pins$':
|
||
|
|
type: object
|
||
|
|
additionalProperties: false
|
||
|
|
|
||
|
|
patternProperties:
|
||
|
|
'.*mux.*':
|
||
|
|
type: object
|
||
|
|
additionalProperties: false
|
||
|
|
description: |
|
||
|
|
pinmux configuration nodes.
|
||
|
|
|
||
|
|
The following table shows the effective values of "group", "function"
|
||
|
|
properties and chip pinout pins
|
||
|
|
|
||
|
|
groups function pins (in pin#)
|
||
|
|
---------------------------------------------------------------------
|
||
|
|
"watchdog" "watchdog" 0
|
||
|
|
"wifi_led" "led" 1, 2
|
||
|
|
"i2c" "i2c" 3, 4
|
||
|
|
"uart1_0" "uart" 7, 8, 9, 10
|
||
|
|
"uart1_rx_tx" "uart" 42, 43
|
||
|
|
"uart1_cts_rts" "uart" 44, 45
|
||
|
|
"pcie_clk" "pcie" 9
|
||
|
|
"pcie_wake" "pcie" 10
|
||
|
|
"spi1_0" "spi" 11, 12, 13, 14
|
||
|
|
"pwm1_1" "pwm" 20,
|
||
|
|
"pwm0" "pwm" 21,
|
||
|
|
"pwm1_0" "pwm" 22,
|
||
|
|
"snfi" "flash" 23, 24, 25, 26, 27, 28
|
||
|
|
"spi1_2" "spi" 29, 30, 31, 32
|
||
|
|
"emmc_45" "emmc" 22, 23, 24, 25, 26, 27, 28, 29, 30,
|
||
|
|
31, 32
|
||
|
|
"spi1_1" "spi" 23, 24, 25, 26
|
||
|
|
"uart1_2_rx_tx" "uart" 29, 30
|
||
|
|
"uart1_2_cts_rts" "uart" 31, 32
|
||
|
|
"uart1_1" "uart" 23, 24, 25, 26
|
||
|
|
"uart2_0_rx_tx" "uart" 29, 30
|
||
|
|
"uart2_0_cts_rts" "uart" 31, 32
|
||
|
|
"spi0" "spi" 33, 34, 35, 36
|
||
|
|
"spi0_wp_hold" "spi" 37, 38
|
||
|
|
"uart1_3_rx_tx" "uart" 35, 36
|
||
|
|
"uart1_3_cts_rts" "uart" 37, 38
|
||
|
|
"uart2_1" "uart" 33, 34, 35, 36
|
||
|
|
"spi1_3" "spi" 33, 34, 35, 36
|
||
|
|
"uart0" "uart" 39, 40
|
||
|
|
"pcie_pereset" "pcie" 41
|
||
|
|
"uart1" "uart" 42, 43, 44, 45
|
||
|
|
"uart2" "uart" 46, 47, 48, 49
|
||
|
|
"emmc_51" "emmc" 50, 51, 52, 53, 54, 55, 56, 57, 57,
|
||
|
|
59, 60, 61
|
||
|
|
"pcm" "audio" 62, 63, 64, 65
|
||
|
|
"i2s" "audio" 62, 63, 64, 65
|
||
|
|
"switch_int" "eth" 66
|
||
|
|
"mdc_mdio" "eth" 67
|
||
|
|
"wf_2g" "wifi" 74, 75, 76, 77, 78, 79, 80, 81, 82, 83
|
||
|
|
"wf_5g" "wifi" 91, 92, 93, 94, 95, 96, 97, 98, 99, 100
|
||
|
|
"wf_dbdc" "wifi" 74, 75, 76, 77, 78, 79, 80, 81, 82, 83,
|
||
|
|
84, 85
|
||
|
|
|
||
|
|
$ref: "/schemas/pinctrl/pinmux-node.yaml"
|
||
|
|
properties:
|
||
|
|
function:
|
||
|
|
description: |
|
||
|
|
A string containing the name of the function to mux to the group.
|
||
|
|
There is no "audio", "pcie" functions on mt7986b, you can only use
|
||
|
|
those functions on mt7986a.
|
||
|
|
enum: [audio, emmc, eth, i2c, led, flash, pcie, pwm, spi, uart,
|
||
|
|
watchdog, wifi]
|
||
|
|
groups:
|
||
|
|
description: |
|
||
|
|
An array of strings. Each string contains the name of a group.
|
||
|
|
There is no "pcie_pereset", "uart1", "uart2" "emmc_51", "pcm",
|
||
|
|
and "i2s" groups on mt7986b, you can only use those groups on
|
||
|
|
mt7986a.
|
||
|
|
required:
|
||
|
|
- function
|
||
|
|
- groups
|
||
|
|
|
||
|
|
allOf:
|
||
|
|
- if:
|
||
|
|
properties:
|
||
|
|
function:
|
||
|
|
const: audio
|
||
|
|
then:
|
||
|
|
properties:
|
||
|
|
groups:
|
||
|
|
enum: [pcm, i2s]
|
||
|
|
- if:
|
||
|
|
properties:
|
||
|
|
function:
|
||
|
|
const: emmc
|
||
|
|
then:
|
||
|
|
properties:
|
||
|
|
groups:
|
||
|
|
enum: [emmc_45, emmc_51]
|
||
|
|
- if:
|
||
|
|
properties:
|
||
|
|
function:
|
||
|
|
const: eth
|
||
|
|
then:
|
||
|
|
properties:
|
||
|
|
groups:
|
||
|
|
enum: [switch_int, mdc_mdio]
|
||
|
|
- if:
|
||
|
|
properties:
|
||
|
|
function:
|
||
|
|
const: i2c
|
||
|
|
then:
|
||
|
|
properties:
|
||
|
|
groups:
|
||
|
|
enum: [i2c]
|
||
|
|
- if:
|
||
|
|
properties:
|
||
|
|
function:
|
||
|
|
const: led
|
||
|
|
then:
|
||
|
|
properties:
|
||
|
|
groups:
|
||
|
|
enum: [wifi_led]
|
||
|
|
- if:
|
||
|
|
properties:
|
||
|
|
function:
|
||
|
|
const: flash
|
||
|
|
then:
|
||
|
|
properties:
|
||
|
|
groups:
|
||
|
|
enum: [snfi]
|
||
|
|
- if:
|
||
|
|
properties:
|
||
|
|
function:
|
||
|
|
const: pcie
|
||
|
|
then:
|
||
|
|
properties:
|
||
|
|
groups:
|
||
|
|
items:
|
||
|
|
enum: [pcie_clk, pcie_wake, pcie_pereset]
|
||
|
|
maxItems: 3
|
||
|
|
- if:
|
||
|
|
properties:
|
||
|
|
function:
|
||
|
|
const: pwm
|
||
|
|
then:
|
||
|
|
properties:
|
||
|
|
groups:
|
||
|
|
items:
|
||
|
|
enum: [pwm0, pwm1_0, pwm1_1]
|
||
|
|
maxItems: 2
|
||
|
|
- if:
|
||
|
|
properties:
|
||
|
|
function:
|
||
|
|
const: spi
|
||
|
|
then:
|
||
|
|
properties:
|
||
|
|
groups:
|
||
|
|
items:
|
||
|
|
enum: [spi0, spi0_wp_hold, spi1_0, spi1_1, spi1_2, spi1_3]
|
||
|
|
maxItems: 2
|
||
|
|
- if:
|
||
|
|
properties:
|
||
|
|
function:
|
||
|
|
const: uart
|
||
|
|
then:
|
||
|
|
properties:
|
||
|
|
groups:
|
||
|
|
items:
|
||
|
|
enum: [uart1_0, uart1_rx_tx, uart1_cts_rts, uart1_1,
|
||
|
|
uart1_2_rx_tx, uart1_2_cts_rts, uart1_3_rx_tx,
|
||
|
|
uart1_3_cts_rts, uart2_0_rx_tx, uart2_0_cts_rts,
|
||
|
|
uart2_1, uart0, uart1, uart2]
|
||
|
|
maxItems: 2
|
||
|
|
- if:
|
||
|
|
properties:
|
||
|
|
function:
|
||
|
|
const: watchdog
|
||
|
|
then:
|
||
|
|
properties:
|
||
|
|
groups:
|
||
|
|
enum: [watchdog]
|
||
|
|
- if:
|
||
|
|
properties:
|
||
|
|
function:
|
||
|
|
const: wifi
|
||
|
|
then:
|
||
|
|
properties:
|
||
|
|
groups:
|
||
|
|
items:
|
||
|
|
enum: [wf_2g, wf_5g, wf_dbdc]
|
||
|
|
maxItems: 3
|
||
|
|
'.*conf.*':
|
||
|
|
type: object
|
||
|
|
additionalProperties: false
|
||
|
|
description: |
|
||
|
|
pinconf configuration nodes.
|
||
|
|
$ref: "/schemas/pinctrl/pincfg-node.yaml"
|
||
|
|
|
||
|
|
properties:
|
||
|
|
pins:
|
||
|
|
description: |
|
||
|
|
An array of strings. Each string contains the name of a pin.
|
||
|
|
There is no PIN 41 to PIN 65 above on mt7686b, you can only use
|
||
|
|
those pins on mt7986a.
|
||
|
|
items:
|
||
|
|
enum: [SYS_WATCHDOG, WF2G_LED, WF5G_LED, I2C_SCL, I2C_SDA, GPIO_0,
|
||
|
|
GPIO_1, GPIO_2, GPIO_3, GPIO_4, GPIO_5, GPIO_6, GPIO_7,
|
||
|
|
GPIO_8, GPIO_9, GPIO_10, GPIO_11, GPIO_12, GPIO_13, GPIO_14,
|
||
|
|
GPIO_15, PWM0, PWM1, SPI0_CLK, SPI0_MOSI, SPI0_MISO, SPI0_CS,
|
||
|
|
SPI0_HOLD, SPI0_WP, SPI1_CLK, SPI1_MOSI, SPI1_MISO, SPI1_CS,
|
||
|
|
SPI2_CLK, SPI2_MOSI, SPI2_MISO, SPI2_CS, SPI2_HOLD, SPI2_WP,
|
||
|
|
UART0_RXD, UART0_TXD, PCIE_PERESET_N, UART1_RXD, UART1_TXD,
|
||
|
|
UART1_CTS, UART1_RTS, UART2_RXD, UART2_TXD, UART2_CTS,
|
||
|
|
UART2_RTS, EMMC_DATA_0, EMMC_DATA_1, EMMC_DATA_2,
|
||
|
|
EMMC_DATA_3, EMMC_DATA_4, EMMC_DATA_5, EMMC_DATA_6,
|
||
|
|
EMMC_DATA_7, EMMC_CMD, EMMC_CK, EMMC_DSL, EMMC_RSTB, PCM_DTX,
|
||
|
|
PCM_DRX, PCM_CLK, PCM_FS, MT7531_INT, SMI_MDC, SMI_MDIO,
|
||
|
|
WF0_DIG_RESETB, WF0_CBA_RESETB, WF0_XO_REQ, WF0_TOP_CLK,
|
||
|
|
WF0_TOP_DATA, WF0_HB1, WF0_HB2, WF0_HB3, WF0_HB4, WF0_HB0,
|
||
|
|
WF0_HB0_B, WF0_HB5, WF0_HB6, WF0_HB7, WF0_HB8, WF0_HB9,
|
||
|
|
WF0_HB10, WF1_DIG_RESETB, WF1_CBA_RESETB, WF1_XO_REQ,
|
||
|
|
WF1_TOP_CLK, WF1_TOP_DATA, WF1_HB1, WF1_HB2, WF1_HB3,
|
||
|
|
WF1_HB4, WF1_HB0, WF1_HB0_B, WF1_HB5, WF1_HB6, WF1_HB7,
|
||
|
|
WF1_HB8]
|
||
|
|
maxItems: 101
|
||
|
|
|
||
|
|
bias-disable: true
|
||
|
|
|
||
|
|
bias-pull-up:
|
||
|
|
oneOf:
|
||
|
|
- type: boolean
|
||
|
|
description: normal pull up.
|
||
|
|
- enum: [100, 101, 102, 103]
|
||
|
|
description: |
|
||
|
|
PUPD/R1/R0 pull down type. See MTK_PUPD_SET_R1R0 defines in
|
||
|
|
dt-bindings/pinctrl/mt65xx.h.
|
||
|
|
|
||
|
|
bias-pull-down:
|
||
|
|
oneOf:
|
||
|
|
- type: boolean
|
||
|
|
description: normal pull down.
|
||
|
|
- enum: [100, 101, 102, 103]
|
||
|
|
description: |
|
||
|
|
PUPD/R1/R0 pull down type. See MTK_PUPD_SET_R1R0 defines in
|
||
|
|
dt-bindings/pinctrl/mt65xx.h.
|
||
|
|
|
||
|
|
input-enable: true
|
||
|
|
|
||
|
|
input-disable: true
|
||
|
|
|
||
|
|
output-enable: true
|
||
|
|
|
||
|
|
output-low: true
|
||
|
|
|
||
|
|
output-high: true
|
||
|
|
|
||
|
|
input-schmitt-enable: true
|
||
|
|
|
||
|
|
input-schmitt-disable: true
|
||
|
|
|
||
|
|
drive-strength:
|
||
|
|
enum: [2, 4, 6, 8, 10, 12, 14, 16]
|
||
|
|
|
||
|
|
mediatek,pull-up-adv:
|
||
|
|
description: |
|
||
|
|
Valid arguments for 'mediatek,pull-up-adv' are '0', '1', '2', '3'
|
||
|
|
Pull up setings for 2 pull resistors, R0 and R1. Valid arguments
|
||
|
|
are described as below:
|
||
|
|
0: (R1, R0) = (0, 0) which means R1 disabled and R0 disabled.
|
||
|
|
1: (R1, R0) = (0, 1) which means R1 disabled and R0 enabled.
|
||
|
|
2: (R1, R0) = (1, 0) which means R1 enabled and R0 disabled.
|
||
|
|
3: (R1, R0) = (1, 1) which means R1 enabled and R0 enabled.
|
||
|
|
$ref: /schemas/types.yaml#/definitions/uint32
|
||
|
|
enum: [0, 1, 2, 3]
|
||
|
|
|
||
|
|
mediatek,pull-down-adv:
|
||
|
|
description: |
|
||
|
|
Valid arguments for 'mediatek,pull-up-adv' are '0', '1', '2', '3'
|
||
|
|
Pull down setings for 2 pull resistors, R0 and R1. Valid arguments
|
||
|
|
are described as below:
|
||
|
|
0: (R1, R0) = (0, 0) which means R1 disabled and R0 disabled.
|
||
|
|
1: (R1, R0) = (0, 1) which means R1 disabled and R0 enabled.
|
||
|
|
2: (R1, R0) = (1, 0) which means R1 enabled and R0 disabled.
|
||
|
|
3: (R1, R0) = (1, 1) which means R1 enabled and R0 enabled.
|
||
|
|
$ref: /schemas/types.yaml#/definitions/uint32
|
||
|
|
enum: [0, 1, 2, 3]
|
||
|
|
|
||
|
|
required:
|
||
|
|
- pins
|
||
|
|
|
||
|
|
additionalProperties: false
|
||
|
|
|
||
|
|
examples:
|
||
|
|
- |
|
||
|
|
#include <dt-bindings/interrupt-controller/irq.h>
|
||
|
|
#include <dt-bindings/interrupt-controller/arm-gic.h>
|
||
|
|
#include <dt-bindings/pinctrl/mt65xx.h>
|
||
|
|
|
||
|
|
soc {
|
||
|
|
#address-cells = <2>;
|
||
|
|
#size-cells = <2>;
|
||
|
|
pio: pinctrl@1001f000 {
|
||
|
|
compatible = "mediatek,mt7986a-pinctrl";
|
||
|
|
reg = <0 0x1001f000 0 0x1000>,
|
||
|
|
<0 0x11c30000 0 0x1000>,
|
||
|
|
<0 0x11c40000 0 0x1000>,
|
||
|
|
<0 0x11e20000 0 0x1000>,
|
||
|
|
<0 0x11e30000 0 0x1000>,
|
||
|
|
<0 0x11f00000 0 0x1000>,
|
||
|
|
<0 0x11f10000 0 0x1000>,
|
||
|
|
<0 0x1000b000 0 0x1000>;
|
||
|
|
reg-names = "gpio", "iocfg_rt", "iocfg_rb", "iocfg_lt",
|
||
|
|
"iocfg_lb", "iocfg_tr", "iocfg_tl", "eint";
|
||
|
|
gpio-controller;
|
||
|
|
#gpio-cells = <2>;
|
||
|
|
gpio-ranges = <&pio 0 0 100>;
|
||
|
|
interrupt-controller;
|
||
|
|
interrupts = <GIC_SPI 225 IRQ_TYPE_LEVEL_HIGH>;
|
||
|
|
interrupt-parent = <&gic>;
|
||
|
|
#interrupt-cells = <2>;
|
||
|
|
|
||
|
|
pcie_pins: pcie-pins {
|
||
|
|
mux {
|
||
|
|
function = "pcie";
|
||
|
|
groups = "pcie_clk", "pcie_wake", "pcie_pereset";
|
||
|
|
};
|
||
|
|
};
|
||
|
|
|
||
|
|
pwm_pins: pwm-pins {
|
||
|
|
mux {
|
||
|
|
function = "pwm";
|
||
|
|
groups = "pwm0", "pwm1_0";
|
||
|
|
};
|
||
|
|
};
|
||
|
|
|
||
|
|
spi0_pins: spi0-pins {
|
||
|
|
mux {
|
||
|
|
function = "spi";
|
||
|
|
groups = "spi0", "spi0_wp_hold";
|
||
|
|
};
|
||
|
|
};
|
||
|
|
|
||
|
|
uart1_pins: uart1-pins {
|
||
|
|
mux {
|
||
|
|
function = "uart";
|
||
|
|
groups = "uart1";
|
||
|
|
};
|
||
|
|
};
|
||
|
|
|
||
|
|
uart1_3_pins: uart1-3-pins {
|
||
|
|
mux {
|
||
|
|
function = "uart";
|
||
|
|
groups = "uart1_3_rx_tx", "uart1_3_cts_rts";
|
||
|
|
};
|
||
|
|
};
|
||
|
|
|
||
|
|
uart2_pins: uart2-pins {
|
||
|
|
mux {
|
||
|
|
function = "uart";
|
||
|
|
groups = "uart2";
|
||
|
|
};
|
||
|
|
};
|
||
|
|
|
||
|
|
mmc0_pins_default: mmc0-pins {
|
||
|
|
mux {
|
||
|
|
function = "emmc";
|
||
|
|
groups = "emmc_51";
|
||
|
|
};
|
||
|
|
conf-cmd-dat {
|
||
|
|
pins = "EMMC_DATA_0", "EMMC_DATA_1", "EMMC_DATA_2",
|
||
|
|
"EMMC_DATA_3", "EMMC_DATA_4", "EMMC_DATA_5",
|
||
|
|
"EMMC_DATA_6", "EMMC_DATA_7", "EMMC_CMD";
|
||
|
|
input-enable;
|
||
|
|
drive-strength = <4>;
|
||
|
|
bias-pull-up = <MTK_PUPD_SET_R1R0_01>; /* pull-up 10K */
|
||
|
|
};
|
||
|
|
conf-clk {
|
||
|
|
pins = "EMMC_CK";
|
||
|
|
drive-strength = <6>;
|
||
|
|
bias-pull-down = <MTK_PUPD_SET_R1R0_10>; /* pull-down 50K */
|
||
|
|
};
|
||
|
|
conf-ds {
|
||
|
|
pins = "EMMC_DSL";
|
||
|
|
bias-pull-down = <MTK_PUPD_SET_R1R0_10>; /* pull-down 50K */
|
||
|
|
};
|
||
|
|
conf-rst {
|
||
|
|
pins = "EMMC_RSTB";
|
||
|
|
drive-strength = <4>;
|
||
|
|
bias-pull-up = <MTK_PUPD_SET_R1R0_01>; /* pull-up 10K */
|
||
|
|
};
|
||
|
|
};
|
||
|
|
|
||
|
|
};
|
||
|
|
};
|