1207 lines
39 KiB
C
1207 lines
39 KiB
C
|
/* SPDX-License-Identifier: ISC */
|
||
|
/*
|
||
|
* Copyright (c) 2005-2011 Atheros Communications Inc.
|
||
|
* Copyright (c) 2011-2017 Qualcomm Atheros, Inc.
|
||
|
* Copyright (c) 2018 The Linux Foundation. All rights reserved.
|
||
|
*/
|
||
|
|
||
|
#ifndef _HW_H_
|
||
|
#define _HW_H_
|
||
|
|
||
|
#include "targaddrs.h"
|
||
|
|
||
|
enum ath10k_bus {
|
||
|
ATH10K_BUS_PCI,
|
||
|
ATH10K_BUS_AHB,
|
||
|
ATH10K_BUS_SDIO,
|
||
|
ATH10K_BUS_USB,
|
||
|
ATH10K_BUS_SNOC,
|
||
|
};
|
||
|
|
||
|
#define ATH10K_FW_DIR "ath10k"
|
||
|
|
||
|
#define QCA988X_2_0_DEVICE_ID_UBNT (0x11ac)
|
||
|
#define QCA988X_2_0_DEVICE_ID (0x003c)
|
||
|
#define QCA6164_2_1_DEVICE_ID (0x0041)
|
||
|
#define QCA6174_2_1_DEVICE_ID (0x003e)
|
||
|
#define QCA6174_3_2_DEVICE_ID (0x0042)
|
||
|
#define QCA99X0_2_0_DEVICE_ID (0x0040)
|
||
|
#define QCA9888_2_0_DEVICE_ID (0x0056)
|
||
|
#define QCA9984_1_0_DEVICE_ID (0x0046)
|
||
|
#define QCA9377_1_0_DEVICE_ID (0x0042)
|
||
|
#define QCA9887_1_0_DEVICE_ID (0x0050)
|
||
|
|
||
|
/* QCA988X 1.0 definitions (unsupported) */
|
||
|
#define QCA988X_HW_1_0_CHIP_ID_REV 0x0
|
||
|
|
||
|
/* QCA988X 2.0 definitions */
|
||
|
#define QCA988X_HW_2_0_VERSION 0x4100016c
|
||
|
#define QCA988X_HW_2_0_CHIP_ID_REV 0x2
|
||
|
#define QCA988X_HW_2_0_FW_DIR ATH10K_FW_DIR "/QCA988X/hw2.0"
|
||
|
#define QCA988X_HW_2_0_BOARD_DATA_FILE "board.bin"
|
||
|
#define QCA988X_HW_2_0_PATCH_LOAD_ADDR 0x1234
|
||
|
|
||
|
/* QCA9887 1.0 definitions */
|
||
|
#define QCA9887_HW_1_0_VERSION 0x4100016d
|
||
|
#define QCA9887_HW_1_0_CHIP_ID_REV 0
|
||
|
#define QCA9887_HW_1_0_FW_DIR ATH10K_FW_DIR "/QCA9887/hw1.0"
|
||
|
#define QCA9887_HW_1_0_BOARD_DATA_FILE "board.bin"
|
||
|
#define QCA9887_HW_1_0_PATCH_LOAD_ADDR 0x1234
|
||
|
|
||
|
/* QCA6174 target BMI version signatures */
|
||
|
#define QCA6174_HW_1_0_VERSION 0x05000000
|
||
|
#define QCA6174_HW_1_1_VERSION 0x05000001
|
||
|
#define QCA6174_HW_1_3_VERSION 0x05000003
|
||
|
#define QCA6174_HW_2_1_VERSION 0x05010000
|
||
|
#define QCA6174_HW_3_0_VERSION 0x05020000
|
||
|
#define QCA6174_HW_3_2_VERSION 0x05030000
|
||
|
|
||
|
/* QCA9377 target BMI version signatures */
|
||
|
#define QCA9377_HW_1_0_DEV_VERSION 0x05020000
|
||
|
#define QCA9377_HW_1_1_DEV_VERSION 0x05020001
|
||
|
|
||
|
enum qca6174_pci_rev {
|
||
|
QCA6174_PCI_REV_1_1 = 0x11,
|
||
|
QCA6174_PCI_REV_1_3 = 0x13,
|
||
|
QCA6174_PCI_REV_2_0 = 0x20,
|
||
|
QCA6174_PCI_REV_3_0 = 0x30,
|
||
|
};
|
||
|
|
||
|
enum qca6174_chip_id_rev {
|
||
|
QCA6174_HW_1_0_CHIP_ID_REV = 0,
|
||
|
QCA6174_HW_1_1_CHIP_ID_REV = 1,
|
||
|
QCA6174_HW_1_3_CHIP_ID_REV = 2,
|
||
|
QCA6174_HW_2_1_CHIP_ID_REV = 4,
|
||
|
QCA6174_HW_2_2_CHIP_ID_REV = 5,
|
||
|
QCA6174_HW_3_0_CHIP_ID_REV = 8,
|
||
|
QCA6174_HW_3_1_CHIP_ID_REV = 9,
|
||
|
QCA6174_HW_3_2_CHIP_ID_REV = 10,
|
||
|
};
|
||
|
|
||
|
enum qca9377_chip_id_rev {
|
||
|
QCA9377_HW_1_0_CHIP_ID_REV = 0x0,
|
||
|
QCA9377_HW_1_1_CHIP_ID_REV = 0x1,
|
||
|
};
|
||
|
|
||
|
#define QCA6174_HW_2_1_FW_DIR ATH10K_FW_DIR "/QCA6174/hw2.1"
|
||
|
#define QCA6174_HW_2_1_BOARD_DATA_FILE "board.bin"
|
||
|
#define QCA6174_HW_2_1_PATCH_LOAD_ADDR 0x1234
|
||
|
|
||
|
#define QCA6174_HW_3_0_FW_DIR ATH10K_FW_DIR "/QCA6174/hw3.0"
|
||
|
#define QCA6174_HW_3_0_BOARD_DATA_FILE "board.bin"
|
||
|
#define QCA6174_HW_3_0_PATCH_LOAD_ADDR 0x1234
|
||
|
|
||
|
/* QCA99X0 1.0 definitions (unsupported) */
|
||
|
#define QCA99X0_HW_1_0_CHIP_ID_REV 0x0
|
||
|
|
||
|
/* QCA99X0 2.0 definitions */
|
||
|
#define QCA99X0_HW_2_0_DEV_VERSION 0x01000000
|
||
|
#define QCA99X0_HW_2_0_CHIP_ID_REV 0x1
|
||
|
#define QCA99X0_HW_2_0_FW_DIR ATH10K_FW_DIR "/QCA99X0/hw2.0"
|
||
|
#define QCA99X0_HW_2_0_BOARD_DATA_FILE "board.bin"
|
||
|
#define QCA99X0_HW_2_0_PATCH_LOAD_ADDR 0x1234
|
||
|
|
||
|
/* QCA9984 1.0 defines */
|
||
|
#define QCA9984_HW_1_0_DEV_VERSION 0x1000000
|
||
|
#define QCA9984_HW_DEV_TYPE 0xa
|
||
|
#define QCA9984_HW_1_0_CHIP_ID_REV 0x0
|
||
|
#define QCA9984_HW_1_0_FW_DIR ATH10K_FW_DIR "/QCA9984/hw1.0"
|
||
|
#define QCA9984_HW_1_0_BOARD_DATA_FILE "board.bin"
|
||
|
#define QCA9984_HW_1_0_EBOARD_DATA_FILE "eboard.bin"
|
||
|
#define QCA9984_HW_1_0_PATCH_LOAD_ADDR 0x1234
|
||
|
|
||
|
/* QCA9888 2.0 defines */
|
||
|
#define QCA9888_HW_2_0_DEV_VERSION 0x1000000
|
||
|
#define QCA9888_HW_DEV_TYPE 0xc
|
||
|
#define QCA9888_HW_2_0_CHIP_ID_REV 0x0
|
||
|
#define QCA9888_HW_2_0_FW_DIR ATH10K_FW_DIR "/QCA9888/hw2.0"
|
||
|
#define QCA9888_HW_2_0_BOARD_DATA_FILE "board.bin"
|
||
|
#define QCA9888_HW_2_0_PATCH_LOAD_ADDR 0x1234
|
||
|
|
||
|
/* QCA9377 1.0 definitions */
|
||
|
#define QCA9377_HW_1_0_FW_DIR ATH10K_FW_DIR "/QCA9377/hw1.0"
|
||
|
#define QCA9377_HW_1_0_BOARD_DATA_FILE "board.bin"
|
||
|
#define QCA9377_HW_1_0_PATCH_LOAD_ADDR 0x1234
|
||
|
|
||
|
/* QCA4019 1.0 definitions */
|
||
|
#define QCA4019_HW_1_0_DEV_VERSION 0x01000000
|
||
|
#define QCA4019_HW_1_0_FW_DIR ATH10K_FW_DIR "/QCA4019/hw1.0"
|
||
|
#define QCA4019_HW_1_0_BOARD_DATA_FILE "board.bin"
|
||
|
#define QCA4019_HW_1_0_PATCH_LOAD_ADDR 0x1234
|
||
|
|
||
|
/* WCN3990 1.0 definitions */
|
||
|
#define WCN3990_HW_1_0_DEV_VERSION ATH10K_HW_WCN3990
|
||
|
#define WCN3990_HW_1_0_FW_DIR ATH10K_FW_DIR "/WCN3990/hw1.0"
|
||
|
|
||
|
#define ATH10K_FW_FILE_BASE "firmware"
|
||
|
#define ATH10K_FW_API_MAX 6
|
||
|
#define ATH10K_FW_API_MIN 2
|
||
|
|
||
|
#define ATH10K_FW_API2_FILE "firmware-2.bin"
|
||
|
#define ATH10K_FW_API3_FILE "firmware-3.bin"
|
||
|
|
||
|
/* added support for ATH10K_FW_IE_WMI_OP_VERSION */
|
||
|
#define ATH10K_FW_API4_FILE "firmware-4.bin"
|
||
|
|
||
|
/* HTT id conflict fix for management frames over HTT */
|
||
|
#define ATH10K_FW_API5_FILE "firmware-5.bin"
|
||
|
|
||
|
/* the firmware-6.bin blob */
|
||
|
#define ATH10K_FW_API6_FILE "firmware-6.bin"
|
||
|
|
||
|
#define ATH10K_FW_UTF_FILE "utf.bin"
|
||
|
#define ATH10K_FW_UTF_API2_FILE "utf-2.bin"
|
||
|
|
||
|
#define ATH10K_FW_UTF_FILE_BASE "utf"
|
||
|
|
||
|
/* includes also the null byte */
|
||
|
#define ATH10K_FIRMWARE_MAGIC "QCA-ATH10K"
|
||
|
#define ATH10K_BOARD_MAGIC "QCA-ATH10K-BOARD"
|
||
|
|
||
|
#define ATH10K_BOARD_API2_FILE "board-2.bin"
|
||
|
|
||
|
#define REG_DUMP_COUNT_QCA988X 60
|
||
|
|
||
|
struct ath10k_fw_ie {
|
||
|
__le32 id;
|
||
|
__le32 len;
|
||
|
u8 data[];
|
||
|
};
|
||
|
|
||
|
enum ath10k_fw_ie_type {
|
||
|
ATH10K_FW_IE_FW_VERSION = 0,
|
||
|
ATH10K_FW_IE_TIMESTAMP = 1,
|
||
|
ATH10K_FW_IE_FEATURES = 2,
|
||
|
ATH10K_FW_IE_FW_IMAGE = 3,
|
||
|
ATH10K_FW_IE_OTP_IMAGE = 4,
|
||
|
|
||
|
/* WMI "operations" interface version, 32 bit value. Supported from
|
||
|
* FW API 4 and above.
|
||
|
*/
|
||
|
ATH10K_FW_IE_WMI_OP_VERSION = 5,
|
||
|
|
||
|
/* HTT "operations" interface version, 32 bit value. Supported from
|
||
|
* FW API 5 and above.
|
||
|
*/
|
||
|
ATH10K_FW_IE_HTT_OP_VERSION = 6,
|
||
|
|
||
|
/* Code swap image for firmware binary */
|
||
|
ATH10K_FW_IE_FW_CODE_SWAP_IMAGE = 7,
|
||
|
};
|
||
|
|
||
|
enum ath10k_fw_wmi_op_version {
|
||
|
ATH10K_FW_WMI_OP_VERSION_UNSET = 0,
|
||
|
|
||
|
ATH10K_FW_WMI_OP_VERSION_MAIN = 1,
|
||
|
ATH10K_FW_WMI_OP_VERSION_10_1 = 2,
|
||
|
ATH10K_FW_WMI_OP_VERSION_10_2 = 3,
|
||
|
ATH10K_FW_WMI_OP_VERSION_TLV = 4,
|
||
|
ATH10K_FW_WMI_OP_VERSION_10_2_4 = 5,
|
||
|
ATH10K_FW_WMI_OP_VERSION_10_4 = 6,
|
||
|
|
||
|
/* keep last */
|
||
|
ATH10K_FW_WMI_OP_VERSION_MAX,
|
||
|
};
|
||
|
|
||
|
enum ath10k_fw_htt_op_version {
|
||
|
ATH10K_FW_HTT_OP_VERSION_UNSET = 0,
|
||
|
|
||
|
ATH10K_FW_HTT_OP_VERSION_MAIN = 1,
|
||
|
|
||
|
/* also used in 10.2 and 10.2.4 branches */
|
||
|
ATH10K_FW_HTT_OP_VERSION_10_1 = 2,
|
||
|
|
||
|
ATH10K_FW_HTT_OP_VERSION_TLV = 3,
|
||
|
|
||
|
ATH10K_FW_HTT_OP_VERSION_10_4 = 4,
|
||
|
|
||
|
/* keep last */
|
||
|
ATH10K_FW_HTT_OP_VERSION_MAX,
|
||
|
};
|
||
|
|
||
|
enum ath10k_bd_ie_type {
|
||
|
/* contains sub IEs of enum ath10k_bd_ie_board_type */
|
||
|
ATH10K_BD_IE_BOARD = 0,
|
||
|
ATH10K_BD_IE_BOARD_EXT = 1,
|
||
|
};
|
||
|
|
||
|
enum ath10k_bd_ie_board_type {
|
||
|
ATH10K_BD_IE_BOARD_NAME = 0,
|
||
|
ATH10K_BD_IE_BOARD_DATA = 1,
|
||
|
};
|
||
|
|
||
|
enum ath10k_hw_rev {
|
||
|
ATH10K_HW_QCA988X,
|
||
|
ATH10K_HW_QCA6174,
|
||
|
ATH10K_HW_QCA99X0,
|
||
|
ATH10K_HW_QCA9888,
|
||
|
ATH10K_HW_QCA9984,
|
||
|
ATH10K_HW_QCA9377,
|
||
|
ATH10K_HW_QCA4019,
|
||
|
ATH10K_HW_QCA9887,
|
||
|
ATH10K_HW_WCN3990,
|
||
|
};
|
||
|
|
||
|
struct ath10k_hw_regs {
|
||
|
u32 rtc_soc_base_address;
|
||
|
u32 rtc_wmac_base_address;
|
||
|
u32 soc_core_base_address;
|
||
|
u32 wlan_mac_base_address;
|
||
|
u32 ce_wrapper_base_address;
|
||
|
u32 ce0_base_address;
|
||
|
u32 ce1_base_address;
|
||
|
u32 ce2_base_address;
|
||
|
u32 ce3_base_address;
|
||
|
u32 ce4_base_address;
|
||
|
u32 ce5_base_address;
|
||
|
u32 ce6_base_address;
|
||
|
u32 ce7_base_address;
|
||
|
u32 ce8_base_address;
|
||
|
u32 ce9_base_address;
|
||
|
u32 ce10_base_address;
|
||
|
u32 ce11_base_address;
|
||
|
u32 soc_reset_control_si0_rst_mask;
|
||
|
u32 soc_reset_control_ce_rst_mask;
|
||
|
u32 soc_chip_id_address;
|
||
|
u32 scratch_3_address;
|
||
|
u32 fw_indicator_address;
|
||
|
u32 pcie_local_base_address;
|
||
|
u32 ce_wrap_intr_sum_host_msi_lsb;
|
||
|
u32 ce_wrap_intr_sum_host_msi_mask;
|
||
|
u32 pcie_intr_fw_mask;
|
||
|
u32 pcie_intr_ce_mask_all;
|
||
|
u32 pcie_intr_clr_address;
|
||
|
u32 cpu_pll_init_address;
|
||
|
u32 cpu_speed_address;
|
||
|
u32 core_clk_div_address;
|
||
|
};
|
||
|
|
||
|
extern const struct ath10k_hw_regs qca988x_regs;
|
||
|
extern const struct ath10k_hw_regs qca6174_regs;
|
||
|
extern const struct ath10k_hw_regs qca99x0_regs;
|
||
|
extern const struct ath10k_hw_regs qca4019_regs;
|
||
|
extern const struct ath10k_hw_regs wcn3990_regs;
|
||
|
|
||
|
struct ath10k_hw_ce_regs_addr_map {
|
||
|
u32 msb;
|
||
|
u32 lsb;
|
||
|
u32 mask;
|
||
|
};
|
||
|
|
||
|
struct ath10k_hw_ce_ctrl1 {
|
||
|
u32 addr;
|
||
|
u32 hw_mask;
|
||
|
u32 sw_mask;
|
||
|
u32 hw_wr_mask;
|
||
|
u32 sw_wr_mask;
|
||
|
u32 reset_mask;
|
||
|
u32 reset;
|
||
|
struct ath10k_hw_ce_regs_addr_map *src_ring;
|
||
|
struct ath10k_hw_ce_regs_addr_map *dst_ring;
|
||
|
struct ath10k_hw_ce_regs_addr_map *dmax; };
|
||
|
|
||
|
struct ath10k_hw_ce_cmd_halt {
|
||
|
u32 status_reset;
|
||
|
u32 msb;
|
||
|
u32 mask;
|
||
|
struct ath10k_hw_ce_regs_addr_map *status; };
|
||
|
|
||
|
struct ath10k_hw_ce_host_ie {
|
||
|
u32 copy_complete_reset;
|
||
|
struct ath10k_hw_ce_regs_addr_map *copy_complete; };
|
||
|
|
||
|
struct ath10k_hw_ce_host_wm_regs {
|
||
|
u32 dstr_lmask;
|
||
|
u32 dstr_hmask;
|
||
|
u32 srcr_lmask;
|
||
|
u32 srcr_hmask;
|
||
|
u32 cc_mask;
|
||
|
u32 wm_mask;
|
||
|
u32 addr;
|
||
|
};
|
||
|
|
||
|
struct ath10k_hw_ce_misc_regs {
|
||
|
u32 axi_err;
|
||
|
u32 dstr_add_err;
|
||
|
u32 srcr_len_err;
|
||
|
u32 dstr_mlen_vio;
|
||
|
u32 dstr_overflow;
|
||
|
u32 srcr_overflow;
|
||
|
u32 err_mask;
|
||
|
u32 addr;
|
||
|
};
|
||
|
|
||
|
struct ath10k_hw_ce_dst_src_wm_regs {
|
||
|
u32 addr;
|
||
|
u32 low_rst;
|
||
|
u32 high_rst;
|
||
|
struct ath10k_hw_ce_regs_addr_map *wm_low;
|
||
|
struct ath10k_hw_ce_regs_addr_map *wm_high; };
|
||
|
|
||
|
struct ath10k_hw_ce_ctrl1_upd {
|
||
|
u32 shift;
|
||
|
u32 mask;
|
||
|
u32 enable;
|
||
|
};
|
||
|
|
||
|
struct ath10k_hw_ce_regs {
|
||
|
u32 sr_base_addr_lo;
|
||
|
u32 sr_base_addr_hi;
|
||
|
u32 sr_size_addr;
|
||
|
u32 dr_base_addr_lo;
|
||
|
u32 dr_base_addr_hi;
|
||
|
u32 dr_size_addr;
|
||
|
u32 ce_cmd_addr;
|
||
|
u32 misc_ie_addr;
|
||
|
u32 sr_wr_index_addr;
|
||
|
u32 dst_wr_index_addr;
|
||
|
u32 current_srri_addr;
|
||
|
u32 current_drri_addr;
|
||
|
u32 ddr_addr_for_rri_low;
|
||
|
u32 ddr_addr_for_rri_high;
|
||
|
u32 ce_rri_low;
|
||
|
u32 ce_rri_high;
|
||
|
u32 host_ie_addr;
|
||
|
struct ath10k_hw_ce_host_wm_regs *wm_regs;
|
||
|
struct ath10k_hw_ce_misc_regs *misc_regs;
|
||
|
struct ath10k_hw_ce_ctrl1 *ctrl1_regs;
|
||
|
struct ath10k_hw_ce_cmd_halt *cmd_halt;
|
||
|
struct ath10k_hw_ce_host_ie *host_ie;
|
||
|
struct ath10k_hw_ce_dst_src_wm_regs *wm_srcr;
|
||
|
struct ath10k_hw_ce_dst_src_wm_regs *wm_dstr;
|
||
|
struct ath10k_hw_ce_ctrl1_upd *upd;
|
||
|
};
|
||
|
|
||
|
struct ath10k_hw_values {
|
||
|
u32 rtc_state_val_on;
|
||
|
u8 ce_count;
|
||
|
u8 msi_assign_ce_max;
|
||
|
u8 num_target_ce_config_wlan;
|
||
|
u16 ce_desc_meta_data_mask;
|
||
|
u8 ce_desc_meta_data_lsb;
|
||
|
u32 rfkill_pin;
|
||
|
u32 rfkill_cfg;
|
||
|
bool rfkill_on_level;
|
||
|
};
|
||
|
|
||
|
extern const struct ath10k_hw_values qca988x_values;
|
||
|
extern const struct ath10k_hw_values qca6174_values;
|
||
|
extern const struct ath10k_hw_values qca99x0_values;
|
||
|
extern const struct ath10k_hw_values qca9888_values;
|
||
|
extern const struct ath10k_hw_values qca4019_values;
|
||
|
extern const struct ath10k_hw_values wcn3990_values;
|
||
|
extern const struct ath10k_hw_ce_regs wcn3990_ce_regs;
|
||
|
extern const struct ath10k_hw_ce_regs qcax_ce_regs;
|
||
|
|
||
|
void ath10k_hw_fill_survey_time(struct ath10k *ar, struct survey_info *survey,
|
||
|
u32 cc, u32 rcc, u32 cc_prev, u32 rcc_prev);
|
||
|
|
||
|
int ath10k_hw_diag_fast_download(struct ath10k *ar,
|
||
|
u32 address,
|
||
|
const void *buffer,
|
||
|
u32 length);
|
||
|
|
||
|
#define QCA_REV_988X(ar) ((ar)->hw_rev == ATH10K_HW_QCA988X)
|
||
|
#define QCA_REV_9887(ar) ((ar)->hw_rev == ATH10K_HW_QCA9887)
|
||
|
#define QCA_REV_6174(ar) ((ar)->hw_rev == ATH10K_HW_QCA6174)
|
||
|
#define QCA_REV_99X0(ar) ((ar)->hw_rev == ATH10K_HW_QCA99X0)
|
||
|
#define QCA_REV_9888(ar) ((ar)->hw_rev == ATH10K_HW_QCA9888)
|
||
|
#define QCA_REV_9984(ar) ((ar)->hw_rev == ATH10K_HW_QCA9984)
|
||
|
#define QCA_REV_9377(ar) ((ar)->hw_rev == ATH10K_HW_QCA9377)
|
||
|
#define QCA_REV_40XX(ar) ((ar)->hw_rev == ATH10K_HW_QCA4019)
|
||
|
#define QCA_REV_WCN3990(ar) ((ar)->hw_rev == ATH10K_HW_WCN3990)
|
||
|
|
||
|
/* Known peculiarities:
|
||
|
* - raw appears in nwifi decap, raw and nwifi appear in ethernet decap
|
||
|
* - raw have FCS, nwifi doesn't
|
||
|
* - ethernet frames have 802.11 header decapped and parts (base hdr, cipher
|
||
|
* param, llc/snap) are aligned to 4byte boundaries each
|
||
|
*/
|
||
|
enum ath10k_hw_txrx_mode {
|
||
|
ATH10K_HW_TXRX_RAW = 0,
|
||
|
|
||
|
/* Native Wifi decap mode is used to align IP frames to 4-byte
|
||
|
* boundaries and avoid a very expensive re-alignment in mac80211.
|
||
|
*/
|
||
|
ATH10K_HW_TXRX_NATIVE_WIFI = 1,
|
||
|
ATH10K_HW_TXRX_ETHERNET = 2,
|
||
|
|
||
|
/* Valid for HTT >= 3.0. Used for management frames in TX_FRM. */
|
||
|
ATH10K_HW_TXRX_MGMT = 3,
|
||
|
};
|
||
|
|
||
|
enum ath10k_mcast2ucast_mode {
|
||
|
ATH10K_MCAST2UCAST_DISABLED = 0,
|
||
|
ATH10K_MCAST2UCAST_ENABLED = 1,
|
||
|
};
|
||
|
|
||
|
enum ath10k_hw_rate_ofdm {
|
||
|
ATH10K_HW_RATE_OFDM_48M = 0,
|
||
|
ATH10K_HW_RATE_OFDM_24M,
|
||
|
ATH10K_HW_RATE_OFDM_12M,
|
||
|
ATH10K_HW_RATE_OFDM_6M,
|
||
|
ATH10K_HW_RATE_OFDM_54M,
|
||
|
ATH10K_HW_RATE_OFDM_36M,
|
||
|
ATH10K_HW_RATE_OFDM_18M,
|
||
|
ATH10K_HW_RATE_OFDM_9M,
|
||
|
};
|
||
|
|
||
|
enum ath10k_hw_rate_cck {
|
||
|
ATH10K_HW_RATE_CCK_LP_11M = 0,
|
||
|
ATH10K_HW_RATE_CCK_LP_5_5M,
|
||
|
ATH10K_HW_RATE_CCK_LP_2M,
|
||
|
ATH10K_HW_RATE_CCK_LP_1M,
|
||
|
ATH10K_HW_RATE_CCK_SP_11M,
|
||
|
ATH10K_HW_RATE_CCK_SP_5_5M,
|
||
|
ATH10K_HW_RATE_CCK_SP_2M,
|
||
|
};
|
||
|
|
||
|
enum ath10k_hw_rate_rev2_cck {
|
||
|
ATH10K_HW_RATE_REV2_CCK_LP_1M = 1,
|
||
|
ATH10K_HW_RATE_REV2_CCK_LP_2M,
|
||
|
ATH10K_HW_RATE_REV2_CCK_LP_5_5M,
|
||
|
ATH10K_HW_RATE_REV2_CCK_LP_11M,
|
||
|
ATH10K_HW_RATE_REV2_CCK_SP_2M,
|
||
|
ATH10K_HW_RATE_REV2_CCK_SP_5_5M,
|
||
|
ATH10K_HW_RATE_REV2_CCK_SP_11M,
|
||
|
};
|
||
|
|
||
|
enum ath10k_hw_cc_wraparound_type {
|
||
|
ATH10K_HW_CC_WRAP_DISABLED = 0,
|
||
|
|
||
|
/* This type is when the HW chip has a quirky Cycle Counter
|
||
|
* wraparound which resets to 0x7fffffff instead of 0. All
|
||
|
* other CC related counters (e.g. Rx Clear Count) are divided
|
||
|
* by 2 so they never wraparound themselves.
|
||
|
*/
|
||
|
ATH10K_HW_CC_WRAP_SHIFTED_ALL = 1,
|
||
|
|
||
|
/* Each hw counter wrapsaround independently. When the
|
||
|
* counter overflows the repestive counter is right shifted
|
||
|
* by 1, i.e reset to 0x7fffffff, and other counters will be
|
||
|
* running unaffected. In this type of wraparound, it should
|
||
|
* be possible to report accurate Rx busy time unlike the
|
||
|
* first type.
|
||
|
*/
|
||
|
ATH10K_HW_CC_WRAP_SHIFTED_EACH = 2,
|
||
|
};
|
||
|
|
||
|
enum ath10k_hw_refclk_speed {
|
||
|
ATH10K_HW_REFCLK_UNKNOWN = -1,
|
||
|
ATH10K_HW_REFCLK_48_MHZ = 0,
|
||
|
ATH10K_HW_REFCLK_19_2_MHZ = 1,
|
||
|
ATH10K_HW_REFCLK_24_MHZ = 2,
|
||
|
ATH10K_HW_REFCLK_26_MHZ = 3,
|
||
|
ATH10K_HW_REFCLK_37_4_MHZ = 4,
|
||
|
ATH10K_HW_REFCLK_38_4_MHZ = 5,
|
||
|
ATH10K_HW_REFCLK_40_MHZ = 6,
|
||
|
ATH10K_HW_REFCLK_52_MHZ = 7,
|
||
|
|
||
|
/* must be the last one */
|
||
|
ATH10K_HW_REFCLK_COUNT,
|
||
|
};
|
||
|
|
||
|
struct ath10k_hw_clk_params {
|
||
|
u32 refclk;
|
||
|
u32 div;
|
||
|
u32 rnfrac;
|
||
|
u32 settle_time;
|
||
|
u32 refdiv;
|
||
|
u32 outdiv;
|
||
|
};
|
||
|
|
||
|
struct htt_rx_desc_ops;
|
||
|
|
||
|
struct ath10k_hw_params {
|
||
|
u32 id;
|
||
|
u16 dev_id;
|
||
|
enum ath10k_bus bus;
|
||
|
const char *name;
|
||
|
u32 patch_load_addr;
|
||
|
int uart_pin;
|
||
|
u32 otp_exe_param;
|
||
|
|
||
|
/* Type of hw cycle counter wraparound logic, for more info
|
||
|
* refer enum ath10k_hw_cc_wraparound_type.
|
||
|
*/
|
||
|
enum ath10k_hw_cc_wraparound_type cc_wraparound_type;
|
||
|
|
||
|
/* Some of chip expects fragment descriptor to be continuous
|
||
|
* memory for any TX operation. Set continuous_frag_desc flag
|
||
|
* for the hardware which have such requirement.
|
||
|
*/
|
||
|
bool continuous_frag_desc;
|
||
|
|
||
|
/* CCK hardware rate table mapping for the newer chipsets
|
||
|
* like QCA99X0, QCA4019 got revised. The CCK h/w rate values
|
||
|
* are in a proper order with respect to the rate/preamble
|
||
|
*/
|
||
|
bool cck_rate_map_rev2;
|
||
|
|
||
|
u32 channel_counters_freq_hz;
|
||
|
|
||
|
/* Mgmt tx descriptors threshold for limiting probe response
|
||
|
* frames.
|
||
|
*/
|
||
|
u32 max_probe_resp_desc_thres;
|
||
|
|
||
|
u32 tx_chain_mask;
|
||
|
u32 rx_chain_mask;
|
||
|
u32 max_spatial_stream;
|
||
|
u32 cal_data_len;
|
||
|
|
||
|
struct ath10k_hw_params_fw {
|
||
|
const char *dir;
|
||
|
const char *board;
|
||
|
size_t board_size;
|
||
|
const char *eboard;
|
||
|
size_t ext_board_size;
|
||
|
size_t board_ext_size;
|
||
|
} fw;
|
||
|
|
||
|
/* qca99x0 family chips deliver broadcast/multicast management
|
||
|
* frames encrypted and expect software do decryption.
|
||
|
*/
|
||
|
bool sw_decrypt_mcast_mgmt;
|
||
|
|
||
|
/* Rx descriptor abstraction */
|
||
|
const struct ath10k_htt_rx_desc_ops *rx_desc_ops;
|
||
|
|
||
|
const struct ath10k_hw_ops *hw_ops;
|
||
|
|
||
|
/* Number of bytes used for alignment in rx_hdr_status of rx desc. */
|
||
|
int decap_align_bytes;
|
||
|
|
||
|
/* hw specific clock control parameters */
|
||
|
const struct ath10k_hw_clk_params *hw_clk;
|
||
|
int target_cpu_freq;
|
||
|
|
||
|
/* Number of bytes to be discarded for each FFT sample */
|
||
|
int spectral_bin_discard;
|
||
|
|
||
|
/* The board may have a restricted NSS for 160 or 80+80 vs what it
|
||
|
* can do for 80Mhz.
|
||
|
*/
|
||
|
int vht160_mcs_rx_highest;
|
||
|
int vht160_mcs_tx_highest;
|
||
|
|
||
|
/* Number of ciphers supported (i.e First N) in cipher_suites array */
|
||
|
int n_cipher_suites;
|
||
|
|
||
|
u32 num_peers;
|
||
|
u32 ast_skid_limit;
|
||
|
u32 num_wds_entries;
|
||
|
|
||
|
/* Targets supporting physical addressing capability above 32-bits */
|
||
|
bool target_64bit;
|
||
|
|
||
|
/* Target rx ring fill level */
|
||
|
u32 rx_ring_fill_level;
|
||
|
|
||
|
/* target supporting shadow register for ce write */
|
||
|
bool shadow_reg_support;
|
||
|
|
||
|
/* target supporting retention restore on ddr */
|
||
|
bool rri_on_ddr;
|
||
|
|
||
|
/* Number of bytes to be the offset for each FFT sample */
|
||
|
int spectral_bin_offset;
|
||
|
|
||
|
/* targets which require hw filter reset during boot up,
|
||
|
* to avoid it sending spurious acks.
|
||
|
*/
|
||
|
bool hw_filter_reset_required;
|
||
|
|
||
|
/* target supporting fw download via diag ce */
|
||
|
bool fw_diag_ce_download;
|
||
|
|
||
|
/* target supporting fw download via large size BMI */
|
||
|
bool bmi_large_size_download;
|
||
|
|
||
|
/* need to set uart pin if disable uart print, workaround for a
|
||
|
* firmware bug
|
||
|
*/
|
||
|
bool uart_pin_workaround;
|
||
|
|
||
|
/* Workaround for the credit size calculation */
|
||
|
bool credit_size_workaround;
|
||
|
|
||
|
/* tx stats support over pktlog */
|
||
|
bool tx_stats_over_pktlog;
|
||
|
|
||
|
/* provides bitrates for sta_statistics using WMI_TLV_PEER_STATS_INFO_EVENTID */
|
||
|
bool supports_peer_stats_info;
|
||
|
|
||
|
bool dynamic_sar_support;
|
||
|
|
||
|
bool hw_restart_disconnect;
|
||
|
|
||
|
bool use_fw_tx_credits;
|
||
|
|
||
|
bool delay_unmap_buffer;
|
||
|
};
|
||
|
|
||
|
struct htt_resp;
|
||
|
struct htt_data_tx_completion_ext;
|
||
|
struct htt_rx_ring_rx_desc_offsets;
|
||
|
|
||
|
/* Defines needed for Rx descriptor abstraction */
|
||
|
struct ath10k_hw_ops {
|
||
|
void (*set_coverage_class)(struct ath10k *ar, s16 value);
|
||
|
int (*enable_pll_clk)(struct ath10k *ar);
|
||
|
int (*tx_data_rssi_pad_bytes)(struct htt_resp *htt);
|
||
|
int (*is_rssi_enable)(struct htt_resp *resp);
|
||
|
};
|
||
|
|
||
|
extern const struct ath10k_hw_ops qca988x_ops;
|
||
|
extern const struct ath10k_hw_ops qca99x0_ops;
|
||
|
extern const struct ath10k_hw_ops qca6174_ops;
|
||
|
extern const struct ath10k_hw_ops qca6174_sdio_ops;
|
||
|
extern const struct ath10k_hw_ops wcn3990_ops;
|
||
|
|
||
|
extern const struct ath10k_hw_clk_params qca6174_clk[];
|
||
|
|
||
|
static inline int
|
||
|
ath10k_tx_data_rssi_get_pad_bytes(struct ath10k_hw_params *hw,
|
||
|
struct htt_resp *htt)
|
||
|
{
|
||
|
if (hw->hw_ops->tx_data_rssi_pad_bytes)
|
||
|
return hw->hw_ops->tx_data_rssi_pad_bytes(htt);
|
||
|
return 0;
|
||
|
}
|
||
|
|
||
|
static inline int
|
||
|
ath10k_is_rssi_enable(struct ath10k_hw_params *hw,
|
||
|
struct htt_resp *resp)
|
||
|
{
|
||
|
if (hw->hw_ops->is_rssi_enable)
|
||
|
return hw->hw_ops->is_rssi_enable(resp);
|
||
|
return 0;
|
||
|
}
|
||
|
|
||
|
/* Target specific defines for MAIN firmware */
|
||
|
#define TARGET_NUM_VDEVS 8
|
||
|
#define TARGET_NUM_PEER_AST 2
|
||
|
#define TARGET_NUM_WDS_ENTRIES 32
|
||
|
#define TARGET_DMA_BURST_SIZE 0
|
||
|
#define TARGET_MAC_AGGR_DELIM 0
|
||
|
#define TARGET_AST_SKID_LIMIT 16
|
||
|
#define TARGET_NUM_STATIONS 16
|
||
|
#define TARGET_NUM_PEERS ((TARGET_NUM_STATIONS) + \
|
||
|
(TARGET_NUM_VDEVS))
|
||
|
#define TARGET_NUM_OFFLOAD_PEERS 0
|
||
|
#define TARGET_NUM_OFFLOAD_REORDER_BUFS 0
|
||
|
#define TARGET_NUM_PEER_KEYS 2
|
||
|
#define TARGET_NUM_TIDS ((TARGET_NUM_PEERS) * 2)
|
||
|
#define TARGET_TX_CHAIN_MASK (BIT(0) | BIT(1) | BIT(2))
|
||
|
#define TARGET_RX_CHAIN_MASK (BIT(0) | BIT(1) | BIT(2))
|
||
|
#define TARGET_RX_TIMEOUT_LO_PRI 100
|
||
|
#define TARGET_RX_TIMEOUT_HI_PRI 40
|
||
|
|
||
|
#define TARGET_SCAN_MAX_PENDING_REQS 4
|
||
|
#define TARGET_BMISS_OFFLOAD_MAX_VDEV 3
|
||
|
#define TARGET_ROAM_OFFLOAD_MAX_VDEV 3
|
||
|
#define TARGET_ROAM_OFFLOAD_MAX_AP_PROFILES 8
|
||
|
#define TARGET_GTK_OFFLOAD_MAX_VDEV 3
|
||
|
#define TARGET_NUM_MCAST_GROUPS 0
|
||
|
#define TARGET_NUM_MCAST_TABLE_ELEMS 0
|
||
|
#define TARGET_MCAST2UCAST_MODE ATH10K_MCAST2UCAST_DISABLED
|
||
|
#define TARGET_TX_DBG_LOG_SIZE 1024
|
||
|
#define TARGET_RX_SKIP_DEFRAG_TIMEOUT_DUP_DETECTION_CHECK 0
|
||
|
#define TARGET_VOW_CONFIG 0
|
||
|
#define TARGET_NUM_MSDU_DESC (1024 + 400)
|
||
|
#define TARGET_MAX_FRAG_ENTRIES 0
|
||
|
|
||
|
/* Target specific defines for 10.X firmware */
|
||
|
#define TARGET_10X_NUM_VDEVS 16
|
||
|
#define TARGET_10X_NUM_PEER_AST 2
|
||
|
#define TARGET_10X_NUM_WDS_ENTRIES 32
|
||
|
#define TARGET_10X_DMA_BURST_SIZE 0
|
||
|
#define TARGET_10X_MAC_AGGR_DELIM 0
|
||
|
#define TARGET_10X_AST_SKID_LIMIT 128
|
||
|
#define TARGET_10X_NUM_STATIONS 128
|
||
|
#define TARGET_10X_TX_STATS_NUM_STATIONS 118
|
||
|
#define TARGET_10X_NUM_PEERS ((TARGET_10X_NUM_STATIONS) + \
|
||
|
(TARGET_10X_NUM_VDEVS))
|
||
|
#define TARGET_10X_TX_STATS_NUM_PEERS ((TARGET_10X_TX_STATS_NUM_STATIONS) + \
|
||
|
(TARGET_10X_NUM_VDEVS))
|
||
|
#define TARGET_10X_NUM_OFFLOAD_PEERS 0
|
||
|
#define TARGET_10X_NUM_OFFLOAD_REORDER_BUFS 0
|
||
|
#define TARGET_10X_NUM_PEER_KEYS 2
|
||
|
#define TARGET_10X_NUM_TIDS_MAX 256
|
||
|
#define TARGET_10X_NUM_TIDS min((TARGET_10X_NUM_TIDS_MAX), \
|
||
|
(TARGET_10X_NUM_PEERS) * 2)
|
||
|
#define TARGET_10X_TX_STATS_NUM_TIDS min((TARGET_10X_NUM_TIDS_MAX), \
|
||
|
(TARGET_10X_TX_STATS_NUM_PEERS) * 2)
|
||
|
#define TARGET_10X_TX_CHAIN_MASK (BIT(0) | BIT(1) | BIT(2))
|
||
|
#define TARGET_10X_RX_CHAIN_MASK (BIT(0) | BIT(1) | BIT(2))
|
||
|
#define TARGET_10X_RX_TIMEOUT_LO_PRI 100
|
||
|
#define TARGET_10X_RX_TIMEOUT_HI_PRI 40
|
||
|
#define TARGET_10X_SCAN_MAX_PENDING_REQS 4
|
||
|
#define TARGET_10X_BMISS_OFFLOAD_MAX_VDEV 2
|
||
|
#define TARGET_10X_ROAM_OFFLOAD_MAX_VDEV 2
|
||
|
#define TARGET_10X_ROAM_OFFLOAD_MAX_AP_PROFILES 8
|
||
|
#define TARGET_10X_GTK_OFFLOAD_MAX_VDEV 3
|
||
|
#define TARGET_10X_NUM_MCAST_GROUPS 0
|
||
|
#define TARGET_10X_NUM_MCAST_TABLE_ELEMS 0
|
||
|
#define TARGET_10X_MCAST2UCAST_MODE ATH10K_MCAST2UCAST_DISABLED
|
||
|
#define TARGET_10X_TX_DBG_LOG_SIZE 1024
|
||
|
#define TARGET_10X_RX_SKIP_DEFRAG_TIMEOUT_DUP_DETECTION_CHECK 1
|
||
|
#define TARGET_10X_VOW_CONFIG 0
|
||
|
#define TARGET_10X_NUM_MSDU_DESC (1024 + 400)
|
||
|
#define TARGET_10X_MAX_FRAG_ENTRIES 0
|
||
|
|
||
|
/* 10.2 parameters */
|
||
|
#define TARGET_10_2_DMA_BURST_SIZE 0
|
||
|
|
||
|
/* Target specific defines for WMI-TLV firmware */
|
||
|
#define TARGET_TLV_NUM_VDEVS 4
|
||
|
#define TARGET_TLV_NUM_STATIONS 32
|
||
|
#define TARGET_TLV_NUM_PEERS 33
|
||
|
#define TARGET_TLV_NUM_TDLS_VDEVS 1
|
||
|
#define TARGET_TLV_NUM_TIDS ((TARGET_TLV_NUM_PEERS) * 2)
|
||
|
#define TARGET_TLV_NUM_MSDU_DESC (1024 + 32)
|
||
|
#define TARGET_TLV_NUM_MSDU_DESC_HL 1024
|
||
|
#define TARGET_TLV_NUM_WOW_PATTERNS 22
|
||
|
#define TARGET_TLV_MGMT_NUM_MSDU_DESC (50)
|
||
|
|
||
|
/* Target specific defines for WMI-HL-1.0 firmware */
|
||
|
#define TARGET_HL_TLV_NUM_PEERS 33
|
||
|
#define TARGET_HL_TLV_AST_SKID_LIMIT 16
|
||
|
#define TARGET_HL_TLV_NUM_WDS_ENTRIES 2
|
||
|
|
||
|
/* Target specific defines for QCA9377 high latency firmware */
|
||
|
#define TARGET_QCA9377_HL_NUM_PEERS 15
|
||
|
|
||
|
/* Diagnostic Window */
|
||
|
#define CE_DIAG_PIPE 7
|
||
|
|
||
|
#define NUM_TARGET_CE_CONFIG_WLAN ar->hw_values->num_target_ce_config_wlan
|
||
|
|
||
|
/* Target specific defines for 10.4 firmware */
|
||
|
#define TARGET_10_4_NUM_VDEVS 16
|
||
|
#define TARGET_10_4_NUM_STATIONS 32
|
||
|
#define TARGET_10_4_NUM_PEERS ((TARGET_10_4_NUM_STATIONS) + \
|
||
|
(TARGET_10_4_NUM_VDEVS))
|
||
|
#define TARGET_10_4_ACTIVE_PEERS 0
|
||
|
|
||
|
#define TARGET_10_4_NUM_QCACHE_PEERS_MAX 512
|
||
|
#define TARGET_10_4_QCACHE_ACTIVE_PEERS 50
|
||
|
#define TARGET_10_4_QCACHE_ACTIVE_PEERS_PFC 35
|
||
|
#define TARGET_10_4_NUM_OFFLOAD_PEERS 0
|
||
|
#define TARGET_10_4_NUM_OFFLOAD_REORDER_BUFFS 0
|
||
|
#define TARGET_10_4_NUM_PEER_KEYS 2
|
||
|
#define TARGET_10_4_TGT_NUM_TIDS ((TARGET_10_4_NUM_PEERS) * 2)
|
||
|
#define TARGET_10_4_NUM_MSDU_DESC (1024 + 400)
|
||
|
#define TARGET_10_4_NUM_MSDU_DESC_PFC 2500
|
||
|
#define TARGET_10_4_AST_SKID_LIMIT 32
|
||
|
|
||
|
/* 100 ms for video, best-effort, and background */
|
||
|
#define TARGET_10_4_RX_TIMEOUT_LO_PRI 100
|
||
|
|
||
|
/* 40 ms for voice */
|
||
|
#define TARGET_10_4_RX_TIMEOUT_HI_PRI 40
|
||
|
|
||
|
#define TARGET_10_4_RX_DECAP_MODE ATH10K_HW_TXRX_NATIVE_WIFI
|
||
|
#define TARGET_10_4_SCAN_MAX_REQS 4
|
||
|
#define TARGET_10_4_BMISS_OFFLOAD_MAX_VDEV 3
|
||
|
#define TARGET_10_4_ROAM_OFFLOAD_MAX_VDEV 3
|
||
|
#define TARGET_10_4_ROAM_OFFLOAD_MAX_PROFILES 8
|
||
|
|
||
|
/* Note: mcast to ucast is disabled by default */
|
||
|
#define TARGET_10_4_NUM_MCAST_GROUPS 0
|
||
|
#define TARGET_10_4_NUM_MCAST_TABLE_ELEMS 0
|
||
|
#define TARGET_10_4_MCAST2UCAST_MODE 0
|
||
|
|
||
|
#define TARGET_10_4_TX_DBG_LOG_SIZE 1024
|
||
|
#define TARGET_10_4_NUM_WDS_ENTRIES 32
|
||
|
#define TARGET_10_4_DMA_BURST_SIZE 1
|
||
|
#define TARGET_10_4_MAC_AGGR_DELIM 0
|
||
|
#define TARGET_10_4_RX_SKIP_DEFRAG_TIMEOUT_DUP_DETECTION_CHECK 1
|
||
|
#define TARGET_10_4_VOW_CONFIG 0
|
||
|
#define TARGET_10_4_GTK_OFFLOAD_MAX_VDEV 3
|
||
|
#define TARGET_10_4_11AC_TX_MAX_FRAGS 2
|
||
|
#define TARGET_10_4_MAX_PEER_EXT_STATS 16
|
||
|
#define TARGET_10_4_SMART_ANT_CAP 0
|
||
|
#define TARGET_10_4_BK_MIN_FREE 0
|
||
|
#define TARGET_10_4_BE_MIN_FREE 0
|
||
|
#define TARGET_10_4_VI_MIN_FREE 0
|
||
|
#define TARGET_10_4_VO_MIN_FREE 0
|
||
|
#define TARGET_10_4_RX_BATCH_MODE 1
|
||
|
#define TARGET_10_4_THERMAL_THROTTLING_CONFIG 0
|
||
|
#define TARGET_10_4_ATF_CONFIG 0
|
||
|
#define TARGET_10_4_IPHDR_PAD_CONFIG 1
|
||
|
#define TARGET_10_4_QWRAP_CONFIG 0
|
||
|
|
||
|
/* TDLS config */
|
||
|
#define TARGET_10_4_NUM_TDLS_VDEVS 1
|
||
|
#define TARGET_10_4_NUM_TDLS_BUFFER_STA 1
|
||
|
#define TARGET_10_4_NUM_TDLS_SLEEP_STA 1
|
||
|
|
||
|
/* Maximum number of Copy Engine's supported */
|
||
|
#define CE_COUNT_MAX 12
|
||
|
|
||
|
/* Number of Copy Engines supported */
|
||
|
#define CE_COUNT ar->hw_values->ce_count
|
||
|
|
||
|
/*
|
||
|
* Granted MSIs are assigned as follows:
|
||
|
* Firmware uses the first
|
||
|
* Remaining MSIs, if any, are used by Copy Engines
|
||
|
* This mapping is known to both Target firmware and Host software.
|
||
|
* It may be changed as long as Host and Target are kept in sync.
|
||
|
*/
|
||
|
/* MSI for firmware (errors, etc.) */
|
||
|
#define MSI_ASSIGN_FW 0
|
||
|
|
||
|
/* MSIs for Copy Engines */
|
||
|
#define MSI_ASSIGN_CE_INITIAL 1
|
||
|
#define MSI_ASSIGN_CE_MAX ar->hw_values->msi_assign_ce_max
|
||
|
|
||
|
/* as of IP3.7.1 */
|
||
|
#define RTC_STATE_V_ON ar->hw_values->rtc_state_val_on
|
||
|
|
||
|
#define RTC_STATE_V_LSB 0
|
||
|
#define RTC_STATE_V_MASK 0x00000007
|
||
|
#define RTC_STATE_ADDRESS 0x0000
|
||
|
#define PCIE_SOC_WAKE_V_MASK 0x00000001
|
||
|
#define PCIE_SOC_WAKE_ADDRESS 0x0004
|
||
|
#define PCIE_SOC_WAKE_RESET 0x00000000
|
||
|
#define SOC_GLOBAL_RESET_ADDRESS 0x0008
|
||
|
|
||
|
#define RTC_SOC_BASE_ADDRESS ar->regs->rtc_soc_base_address
|
||
|
#define RTC_WMAC_BASE_ADDRESS ar->regs->rtc_wmac_base_address
|
||
|
#define MAC_COEX_BASE_ADDRESS 0x00006000
|
||
|
#define BT_COEX_BASE_ADDRESS 0x00007000
|
||
|
#define SOC_PCIE_BASE_ADDRESS 0x00008000
|
||
|
#define SOC_CORE_BASE_ADDRESS ar->regs->soc_core_base_address
|
||
|
#define WLAN_UART_BASE_ADDRESS 0x0000c000
|
||
|
#define WLAN_SI_BASE_ADDRESS 0x00010000
|
||
|
#define WLAN_GPIO_BASE_ADDRESS 0x00014000
|
||
|
#define WLAN_ANALOG_INTF_BASE_ADDRESS 0x0001c000
|
||
|
#define WLAN_MAC_BASE_ADDRESS ar->regs->wlan_mac_base_address
|
||
|
#define EFUSE_BASE_ADDRESS 0x00030000
|
||
|
#define FPGA_REG_BASE_ADDRESS 0x00039000
|
||
|
#define WLAN_UART2_BASE_ADDRESS 0x00054c00
|
||
|
#define CE_WRAPPER_BASE_ADDRESS ar->regs->ce_wrapper_base_address
|
||
|
#define CE0_BASE_ADDRESS ar->regs->ce0_base_address
|
||
|
#define CE1_BASE_ADDRESS ar->regs->ce1_base_address
|
||
|
#define CE2_BASE_ADDRESS ar->regs->ce2_base_address
|
||
|
#define CE3_BASE_ADDRESS ar->regs->ce3_base_address
|
||
|
#define CE4_BASE_ADDRESS ar->regs->ce4_base_address
|
||
|
#define CE5_BASE_ADDRESS ar->regs->ce5_base_address
|
||
|
#define CE6_BASE_ADDRESS ar->regs->ce6_base_address
|
||
|
#define CE7_BASE_ADDRESS ar->regs->ce7_base_address
|
||
|
#define DBI_BASE_ADDRESS 0x00060000
|
||
|
#define WLAN_ANALOG_INTF_PCIE_BASE_ADDRESS 0x0006c000
|
||
|
#define PCIE_LOCAL_BASE_ADDRESS ar->regs->pcie_local_base_address
|
||
|
|
||
|
#define SOC_RESET_CONTROL_ADDRESS 0x00000000
|
||
|
#define SOC_RESET_CONTROL_OFFSET 0x00000000
|
||
|
#define SOC_RESET_CONTROL_SI0_RST_MASK ar->regs->soc_reset_control_si0_rst_mask
|
||
|
#define SOC_RESET_CONTROL_CE_RST_MASK ar->regs->soc_reset_control_ce_rst_mask
|
||
|
#define SOC_RESET_CONTROL_CPU_WARM_RST_MASK 0x00000040
|
||
|
#define SOC_CPU_CLOCK_OFFSET 0x00000020
|
||
|
#define SOC_CPU_CLOCK_STANDARD_LSB 0
|
||
|
#define SOC_CPU_CLOCK_STANDARD_MASK 0x00000003
|
||
|
#define SOC_CLOCK_CONTROL_OFFSET 0x00000028
|
||
|
#define SOC_CLOCK_CONTROL_SI0_CLK_MASK 0x00000001
|
||
|
#define SOC_SYSTEM_SLEEP_OFFSET 0x000000c4
|
||
|
#define SOC_LPO_CAL_OFFSET 0x000000e0
|
||
|
#define SOC_LPO_CAL_ENABLE_LSB 20
|
||
|
#define SOC_LPO_CAL_ENABLE_MASK 0x00100000
|
||
|
#define SOC_LF_TIMER_CONTROL0_ADDRESS 0x00000050
|
||
|
#define SOC_LF_TIMER_CONTROL0_ENABLE_MASK 0x00000004
|
||
|
|
||
|
#define SOC_CHIP_ID_ADDRESS ar->regs->soc_chip_id_address
|
||
|
#define SOC_CHIP_ID_REV_LSB 8
|
||
|
#define SOC_CHIP_ID_REV_MASK 0x00000f00
|
||
|
|
||
|
#define WLAN_RESET_CONTROL_COLD_RST_MASK 0x00000008
|
||
|
#define WLAN_RESET_CONTROL_WARM_RST_MASK 0x00000004
|
||
|
#define WLAN_SYSTEM_SLEEP_DISABLE_LSB 0
|
||
|
#define WLAN_SYSTEM_SLEEP_DISABLE_MASK 0x00000001
|
||
|
|
||
|
#define WLAN_GPIO_PIN0_ADDRESS 0x00000028
|
||
|
#define WLAN_GPIO_PIN0_CONFIG_LSB 11
|
||
|
#define WLAN_GPIO_PIN0_CONFIG_MASK 0x00007800
|
||
|
#define WLAN_GPIO_PIN0_PAD_PULL_LSB 5
|
||
|
#define WLAN_GPIO_PIN0_PAD_PULL_MASK 0x00000060
|
||
|
#define WLAN_GPIO_PIN1_ADDRESS 0x0000002c
|
||
|
#define WLAN_GPIO_PIN1_CONFIG_MASK 0x00007800
|
||
|
#define WLAN_GPIO_PIN10_ADDRESS 0x00000050
|
||
|
#define WLAN_GPIO_PIN11_ADDRESS 0x00000054
|
||
|
#define WLAN_GPIO_PIN12_ADDRESS 0x00000058
|
||
|
#define WLAN_GPIO_PIN13_ADDRESS 0x0000005c
|
||
|
|
||
|
#define CLOCK_GPIO_OFFSET 0xffffffff
|
||
|
#define CLOCK_GPIO_BT_CLK_OUT_EN_LSB 0
|
||
|
#define CLOCK_GPIO_BT_CLK_OUT_EN_MASK 0
|
||
|
|
||
|
#define SI_CONFIG_OFFSET 0x00000000
|
||
|
#define SI_CONFIG_ERR_INT_LSB 19
|
||
|
#define SI_CONFIG_ERR_INT_MASK 0x00080000
|
||
|
#define SI_CONFIG_BIDIR_OD_DATA_LSB 18
|
||
|
#define SI_CONFIG_BIDIR_OD_DATA_MASK 0x00040000
|
||
|
#define SI_CONFIG_I2C_LSB 16
|
||
|
#define SI_CONFIG_I2C_MASK 0x00010000
|
||
|
#define SI_CONFIG_POS_SAMPLE_LSB 7
|
||
|
#define SI_CONFIG_POS_SAMPLE_MASK 0x00000080
|
||
|
#define SI_CONFIG_INACTIVE_DATA_LSB 5
|
||
|
#define SI_CONFIG_INACTIVE_DATA_MASK 0x00000020
|
||
|
#define SI_CONFIG_INACTIVE_CLK_LSB 4
|
||
|
#define SI_CONFIG_INACTIVE_CLK_MASK 0x00000010
|
||
|
#define SI_CONFIG_DIVIDER_LSB 0
|
||
|
#define SI_CONFIG_DIVIDER_MASK 0x0000000f
|
||
|
#define SI_CS_OFFSET 0x00000004
|
||
|
#define SI_CS_DONE_ERR_LSB 10
|
||
|
#define SI_CS_DONE_ERR_MASK 0x00000400
|
||
|
#define SI_CS_DONE_INT_LSB 9
|
||
|
#define SI_CS_DONE_INT_MASK 0x00000200
|
||
|
#define SI_CS_START_LSB 8
|
||
|
#define SI_CS_START_MASK 0x00000100
|
||
|
#define SI_CS_RX_CNT_LSB 4
|
||
|
#define SI_CS_RX_CNT_MASK 0x000000f0
|
||
|
#define SI_CS_TX_CNT_LSB 0
|
||
|
#define SI_CS_TX_CNT_MASK 0x0000000f
|
||
|
|
||
|
#define SI_TX_DATA0_OFFSET 0x00000008
|
||
|
#define SI_TX_DATA1_OFFSET 0x0000000c
|
||
|
#define SI_RX_DATA0_OFFSET 0x00000010
|
||
|
#define SI_RX_DATA1_OFFSET 0x00000014
|
||
|
|
||
|
#define CORE_CTRL_CPU_INTR_MASK 0x00002000
|
||
|
#define CORE_CTRL_PCIE_REG_31_MASK 0x00000800
|
||
|
#define CORE_CTRL_ADDRESS 0x0000
|
||
|
#define PCIE_INTR_ENABLE_ADDRESS 0x0008
|
||
|
#define PCIE_INTR_CAUSE_ADDRESS 0x000c
|
||
|
#define PCIE_INTR_CLR_ADDRESS ar->regs->pcie_intr_clr_address
|
||
|
#define SCRATCH_3_ADDRESS ar->regs->scratch_3_address
|
||
|
#define CPU_INTR_ADDRESS 0x0010
|
||
|
#define FW_RAM_CONFIG_ADDRESS 0x0018
|
||
|
|
||
|
#define CCNT_TO_MSEC(ar, x) ((x) / ar->hw_params.channel_counters_freq_hz)
|
||
|
|
||
|
/* Firmware indications to the Host via SCRATCH_3 register. */
|
||
|
#define FW_INDICATOR_ADDRESS ar->regs->fw_indicator_address
|
||
|
#define FW_IND_EVENT_PENDING 1
|
||
|
#define FW_IND_INITIALIZED 2
|
||
|
#define FW_IND_HOST_READY 0x80000000
|
||
|
|
||
|
/* HOST_REG interrupt from firmware */
|
||
|
#define PCIE_INTR_FIRMWARE_MASK ar->regs->pcie_intr_fw_mask
|
||
|
#define PCIE_INTR_CE_MASK_ALL ar->regs->pcie_intr_ce_mask_all
|
||
|
|
||
|
#define DRAM_BASE_ADDRESS 0x00400000
|
||
|
|
||
|
#define PCIE_BAR_REG_ADDRESS 0x40030
|
||
|
|
||
|
#define MISSING 0
|
||
|
|
||
|
#define SYSTEM_SLEEP_OFFSET SOC_SYSTEM_SLEEP_OFFSET
|
||
|
#define WLAN_SYSTEM_SLEEP_OFFSET SOC_SYSTEM_SLEEP_OFFSET
|
||
|
#define WLAN_RESET_CONTROL_OFFSET SOC_RESET_CONTROL_OFFSET
|
||
|
#define CLOCK_CONTROL_OFFSET SOC_CLOCK_CONTROL_OFFSET
|
||
|
#define CLOCK_CONTROL_SI0_CLK_MASK SOC_CLOCK_CONTROL_SI0_CLK_MASK
|
||
|
#define RESET_CONTROL_MBOX_RST_MASK MISSING
|
||
|
#define RESET_CONTROL_SI0_RST_MASK SOC_RESET_CONTROL_SI0_RST_MASK
|
||
|
#define GPIO_BASE_ADDRESS WLAN_GPIO_BASE_ADDRESS
|
||
|
#define GPIO_PIN0_OFFSET WLAN_GPIO_PIN0_ADDRESS
|
||
|
#define GPIO_PIN1_OFFSET WLAN_GPIO_PIN1_ADDRESS
|
||
|
#define GPIO_PIN0_CONFIG_LSB WLAN_GPIO_PIN0_CONFIG_LSB
|
||
|
#define GPIO_PIN0_CONFIG_MASK WLAN_GPIO_PIN0_CONFIG_MASK
|
||
|
#define GPIO_PIN0_PAD_PULL_LSB WLAN_GPIO_PIN0_PAD_PULL_LSB
|
||
|
#define GPIO_PIN0_PAD_PULL_MASK WLAN_GPIO_PIN0_PAD_PULL_MASK
|
||
|
#define GPIO_PIN1_CONFIG_MASK WLAN_GPIO_PIN1_CONFIG_MASK
|
||
|
#define SI_BASE_ADDRESS WLAN_SI_BASE_ADDRESS
|
||
|
#define SCRATCH_BASE_ADDRESS SOC_CORE_BASE_ADDRESS
|
||
|
#define LOCAL_SCRATCH_OFFSET 0x18
|
||
|
#define CPU_CLOCK_OFFSET SOC_CPU_CLOCK_OFFSET
|
||
|
#define LPO_CAL_OFFSET SOC_LPO_CAL_OFFSET
|
||
|
#define GPIO_PIN10_OFFSET WLAN_GPIO_PIN10_ADDRESS
|
||
|
#define GPIO_PIN11_OFFSET WLAN_GPIO_PIN11_ADDRESS
|
||
|
#define GPIO_PIN12_OFFSET WLAN_GPIO_PIN12_ADDRESS
|
||
|
#define GPIO_PIN13_OFFSET WLAN_GPIO_PIN13_ADDRESS
|
||
|
#define CPU_CLOCK_STANDARD_LSB SOC_CPU_CLOCK_STANDARD_LSB
|
||
|
#define CPU_CLOCK_STANDARD_MASK SOC_CPU_CLOCK_STANDARD_MASK
|
||
|
#define LPO_CAL_ENABLE_LSB SOC_LPO_CAL_ENABLE_LSB
|
||
|
#define LPO_CAL_ENABLE_MASK SOC_LPO_CAL_ENABLE_MASK
|
||
|
#define ANALOG_INTF_BASE_ADDRESS WLAN_ANALOG_INTF_BASE_ADDRESS
|
||
|
#define MBOX_BASE_ADDRESS MISSING
|
||
|
#define INT_STATUS_ENABLE_ERROR_LSB MISSING
|
||
|
#define INT_STATUS_ENABLE_ERROR_MASK MISSING
|
||
|
#define INT_STATUS_ENABLE_CPU_LSB MISSING
|
||
|
#define INT_STATUS_ENABLE_CPU_MASK MISSING
|
||
|
#define INT_STATUS_ENABLE_COUNTER_LSB MISSING
|
||
|
#define INT_STATUS_ENABLE_COUNTER_MASK MISSING
|
||
|
#define INT_STATUS_ENABLE_MBOX_DATA_LSB MISSING
|
||
|
#define INT_STATUS_ENABLE_MBOX_DATA_MASK MISSING
|
||
|
#define ERROR_STATUS_ENABLE_RX_UNDERFLOW_LSB MISSING
|
||
|
#define ERROR_STATUS_ENABLE_RX_UNDERFLOW_MASK MISSING
|
||
|
#define ERROR_STATUS_ENABLE_TX_OVERFLOW_LSB MISSING
|
||
|
#define ERROR_STATUS_ENABLE_TX_OVERFLOW_MASK MISSING
|
||
|
#define COUNTER_INT_STATUS_ENABLE_BIT_LSB MISSING
|
||
|
#define COUNTER_INT_STATUS_ENABLE_BIT_MASK MISSING
|
||
|
#define INT_STATUS_ENABLE_ADDRESS MISSING
|
||
|
#define CPU_INT_STATUS_ENABLE_BIT_LSB MISSING
|
||
|
#define CPU_INT_STATUS_ENABLE_BIT_MASK MISSING
|
||
|
#define HOST_INT_STATUS_ADDRESS MISSING
|
||
|
#define CPU_INT_STATUS_ADDRESS MISSING
|
||
|
#define ERROR_INT_STATUS_ADDRESS MISSING
|
||
|
#define ERROR_INT_STATUS_WAKEUP_MASK MISSING
|
||
|
#define ERROR_INT_STATUS_WAKEUP_LSB MISSING
|
||
|
#define ERROR_INT_STATUS_RX_UNDERFLOW_MASK MISSING
|
||
|
#define ERROR_INT_STATUS_RX_UNDERFLOW_LSB MISSING
|
||
|
#define ERROR_INT_STATUS_TX_OVERFLOW_MASK MISSING
|
||
|
#define ERROR_INT_STATUS_TX_OVERFLOW_LSB MISSING
|
||
|
#define COUNT_DEC_ADDRESS MISSING
|
||
|
#define HOST_INT_STATUS_CPU_MASK MISSING
|
||
|
#define HOST_INT_STATUS_CPU_LSB MISSING
|
||
|
#define HOST_INT_STATUS_ERROR_MASK MISSING
|
||
|
#define HOST_INT_STATUS_ERROR_LSB MISSING
|
||
|
#define HOST_INT_STATUS_COUNTER_MASK MISSING
|
||
|
#define HOST_INT_STATUS_COUNTER_LSB MISSING
|
||
|
#define RX_LOOKAHEAD_VALID_ADDRESS MISSING
|
||
|
#define WINDOW_DATA_ADDRESS MISSING
|
||
|
#define WINDOW_READ_ADDR_ADDRESS MISSING
|
||
|
#define WINDOW_WRITE_ADDR_ADDRESS MISSING
|
||
|
|
||
|
#define QCA9887_1_0_I2C_SDA_GPIO_PIN 5
|
||
|
#define QCA9887_1_0_I2C_SDA_PIN_CONFIG 3
|
||
|
#define QCA9887_1_0_SI_CLK_GPIO_PIN 17
|
||
|
#define QCA9887_1_0_SI_CLK_PIN_CONFIG 3
|
||
|
#define QCA9887_1_0_GPIO_ENABLE_W1TS_LOW_ADDRESS 0x00000010
|
||
|
|
||
|
#define QCA9887_EEPROM_SELECT_READ 0xa10000a0
|
||
|
#define QCA9887_EEPROM_ADDR_HI_MASK 0x0000ff00
|
||
|
#define QCA9887_EEPROM_ADDR_HI_LSB 8
|
||
|
#define QCA9887_EEPROM_ADDR_LO_MASK 0x00ff0000
|
||
|
#define QCA9887_EEPROM_ADDR_LO_LSB 16
|
||
|
|
||
|
#define MBOX_RESET_CONTROL_ADDRESS 0x00000000
|
||
|
#define MBOX_HOST_INT_STATUS_ADDRESS 0x00000800
|
||
|
#define MBOX_HOST_INT_STATUS_ERROR_LSB 7
|
||
|
#define MBOX_HOST_INT_STATUS_ERROR_MASK 0x00000080
|
||
|
#define MBOX_HOST_INT_STATUS_CPU_LSB 6
|
||
|
#define MBOX_HOST_INT_STATUS_CPU_MASK 0x00000040
|
||
|
#define MBOX_HOST_INT_STATUS_COUNTER_LSB 4
|
||
|
#define MBOX_HOST_INT_STATUS_COUNTER_MASK 0x00000010
|
||
|
#define MBOX_CPU_INT_STATUS_ADDRESS 0x00000801
|
||
|
#define MBOX_ERROR_INT_STATUS_ADDRESS 0x00000802
|
||
|
#define MBOX_ERROR_INT_STATUS_WAKEUP_LSB 2
|
||
|
#define MBOX_ERROR_INT_STATUS_WAKEUP_MASK 0x00000004
|
||
|
#define MBOX_ERROR_INT_STATUS_RX_UNDERFLOW_LSB 1
|
||
|
#define MBOX_ERROR_INT_STATUS_RX_UNDERFLOW_MASK 0x00000002
|
||
|
#define MBOX_ERROR_INT_STATUS_TX_OVERFLOW_LSB 0
|
||
|
#define MBOX_ERROR_INT_STATUS_TX_OVERFLOW_MASK 0x00000001
|
||
|
#define MBOX_COUNTER_INT_STATUS_ADDRESS 0x00000803
|
||
|
#define MBOX_COUNTER_INT_STATUS_COUNTER_LSB 0
|
||
|
#define MBOX_COUNTER_INT_STATUS_COUNTER_MASK 0x000000ff
|
||
|
#define MBOX_RX_LOOKAHEAD_VALID_ADDRESS 0x00000805
|
||
|
#define MBOX_INT_STATUS_ENABLE_ADDRESS 0x00000828
|
||
|
#define MBOX_INT_STATUS_ENABLE_ERROR_LSB 7
|
||
|
#define MBOX_INT_STATUS_ENABLE_ERROR_MASK 0x00000080
|
||
|
#define MBOX_INT_STATUS_ENABLE_CPU_LSB 6
|
||
|
#define MBOX_INT_STATUS_ENABLE_CPU_MASK 0x00000040
|
||
|
#define MBOX_INT_STATUS_ENABLE_INT_LSB 5
|
||
|
#define MBOX_INT_STATUS_ENABLE_INT_MASK 0x00000020
|
||
|
#define MBOX_INT_STATUS_ENABLE_COUNTER_LSB 4
|
||
|
#define MBOX_INT_STATUS_ENABLE_COUNTER_MASK 0x00000010
|
||
|
#define MBOX_INT_STATUS_ENABLE_MBOX_DATA_LSB 0
|
||
|
#define MBOX_INT_STATUS_ENABLE_MBOX_DATA_MASK 0x0000000f
|
||
|
#define MBOX_CPU_INT_STATUS_ENABLE_ADDRESS 0x00000819
|
||
|
#define MBOX_CPU_INT_STATUS_ENABLE_BIT_LSB 0
|
||
|
#define MBOX_CPU_INT_STATUS_ENABLE_BIT_MASK 0x000000ff
|
||
|
#define MBOX_CPU_STATUS_ENABLE_ASSERT_MASK 0x00000001
|
||
|
#define MBOX_ERROR_STATUS_ENABLE_ADDRESS 0x0000081a
|
||
|
#define MBOX_ERROR_STATUS_ENABLE_RX_UNDERFLOW_LSB 1
|
||
|
#define MBOX_ERROR_STATUS_ENABLE_RX_UNDERFLOW_MASK 0x00000002
|
||
|
#define MBOX_ERROR_STATUS_ENABLE_TX_OVERFLOW_LSB 0
|
||
|
#define MBOX_ERROR_STATUS_ENABLE_TX_OVERFLOW_MASK 0x00000001
|
||
|
#define MBOX_COUNTER_INT_STATUS_ENABLE_ADDRESS 0x0000081b
|
||
|
#define MBOX_COUNTER_INT_STATUS_ENABLE_BIT_LSB 0
|
||
|
#define MBOX_COUNTER_INT_STATUS_ENABLE_BIT_MASK 0x000000ff
|
||
|
#define MBOX_COUNT_ADDRESS 0x00000820
|
||
|
#define MBOX_COUNT_DEC_ADDRESS 0x00000840
|
||
|
#define MBOX_WINDOW_DATA_ADDRESS 0x00000874
|
||
|
#define MBOX_WINDOW_WRITE_ADDR_ADDRESS 0x00000878
|
||
|
#define MBOX_WINDOW_READ_ADDR_ADDRESS 0x0000087c
|
||
|
#define MBOX_CPU_DBG_SEL_ADDRESS 0x00000883
|
||
|
#define MBOX_CPU_DBG_ADDRESS 0x00000884
|
||
|
#define MBOX_RTC_BASE_ADDRESS 0x00000000
|
||
|
#define MBOX_GPIO_BASE_ADDRESS 0x00005000
|
||
|
#define MBOX_MBOX_BASE_ADDRESS 0x00008000
|
||
|
|
||
|
#define RTC_STATE_V_GET(x) (((x) & RTC_STATE_V_MASK) >> RTC_STATE_V_LSB)
|
||
|
|
||
|
/* Register definitions for first generation ath10k cards. These cards include
|
||
|
* a mac thich has a register allocation similar to ath9k and at least some
|
||
|
* registers including the ones relevant for modifying the coverage class are
|
||
|
* identical to the ath9k definitions.
|
||
|
* These registers are usually managed by the ath10k firmware. However by
|
||
|
* overriding them it is possible to support coverage class modifications.
|
||
|
*/
|
||
|
#define WAVE1_PCU_ACK_CTS_TIMEOUT 0x8014
|
||
|
#define WAVE1_PCU_ACK_CTS_TIMEOUT_MAX 0x00003FFF
|
||
|
#define WAVE1_PCU_ACK_CTS_TIMEOUT_ACK_MASK 0x00003FFF
|
||
|
#define WAVE1_PCU_ACK_CTS_TIMEOUT_ACK_LSB 0
|
||
|
#define WAVE1_PCU_ACK_CTS_TIMEOUT_CTS_MASK 0x3FFF0000
|
||
|
#define WAVE1_PCU_ACK_CTS_TIMEOUT_CTS_LSB 16
|
||
|
|
||
|
#define WAVE1_PCU_GBL_IFS_SLOT 0x1070
|
||
|
#define WAVE1_PCU_GBL_IFS_SLOT_MASK 0x0000FFFF
|
||
|
#define WAVE1_PCU_GBL_IFS_SLOT_MAX 0x0000FFFF
|
||
|
#define WAVE1_PCU_GBL_IFS_SLOT_LSB 0
|
||
|
#define WAVE1_PCU_GBL_IFS_SLOT_RESV0 0xFFFF0000
|
||
|
|
||
|
#define WAVE1_PHYCLK 0x801C
|
||
|
#define WAVE1_PHYCLK_USEC_MASK 0x0000007F
|
||
|
#define WAVE1_PHYCLK_USEC_LSB 0
|
||
|
|
||
|
/* qca6174 PLL offset/mask */
|
||
|
#define SOC_CORE_CLK_CTRL_OFFSET 0x00000114
|
||
|
#define SOC_CORE_CLK_CTRL_DIV_LSB 0
|
||
|
#define SOC_CORE_CLK_CTRL_DIV_MASK 0x00000007
|
||
|
|
||
|
#define EFUSE_OFFSET 0x0000032c
|
||
|
#define EFUSE_XTAL_SEL_LSB 8
|
||
|
#define EFUSE_XTAL_SEL_MASK 0x00000700
|
||
|
|
||
|
#define BB_PLL_CONFIG_OFFSET 0x000002f4
|
||
|
#define BB_PLL_CONFIG_FRAC_LSB 0
|
||
|
#define BB_PLL_CONFIG_FRAC_MASK 0x0003ffff
|
||
|
#define BB_PLL_CONFIG_OUTDIV_LSB 18
|
||
|
#define BB_PLL_CONFIG_OUTDIV_MASK 0x001c0000
|
||
|
|
||
|
#define WLAN_PLL_SETTLE_OFFSET 0x0018
|
||
|
#define WLAN_PLL_SETTLE_TIME_LSB 0
|
||
|
#define WLAN_PLL_SETTLE_TIME_MASK 0x000007ff
|
||
|
|
||
|
#define WLAN_PLL_CONTROL_OFFSET 0x0014
|
||
|
#define WLAN_PLL_CONTROL_DIV_LSB 0
|
||
|
#define WLAN_PLL_CONTROL_DIV_MASK 0x000003ff
|
||
|
#define WLAN_PLL_CONTROL_REFDIV_LSB 10
|
||
|
#define WLAN_PLL_CONTROL_REFDIV_MASK 0x00003c00
|
||
|
#define WLAN_PLL_CONTROL_BYPASS_LSB 16
|
||
|
#define WLAN_PLL_CONTROL_BYPASS_MASK 0x00010000
|
||
|
#define WLAN_PLL_CONTROL_NOPWD_LSB 18
|
||
|
#define WLAN_PLL_CONTROL_NOPWD_MASK 0x00040000
|
||
|
|
||
|
#define RTC_SYNC_STATUS_OFFSET 0x0244
|
||
|
#define RTC_SYNC_STATUS_PLL_CHANGING_LSB 5
|
||
|
#define RTC_SYNC_STATUS_PLL_CHANGING_MASK 0x00000020
|
||
|
/* qca6174 PLL offset/mask end */
|
||
|
|
||
|
/* CPU_ADDR_MSB is a register, bit[3:0] is to specify which memory
|
||
|
* region is accessed. The memory region size is 1M.
|
||
|
* If host wants to access 0xX12345 at target, then CPU_ADDR_MSB[3:0]
|
||
|
* is 0xX.
|
||
|
* The following MACROs are defined to get the 0xX and the size limit.
|
||
|
*/
|
||
|
#define CPU_ADDR_MSB_REGION_MASK GENMASK(23, 20)
|
||
|
#define CPU_ADDR_MSB_REGION_VAL(X) FIELD_GET(CPU_ADDR_MSB_REGION_MASK, X)
|
||
|
#define REGION_ACCESS_SIZE_LIMIT 0x100000
|
||
|
#define REGION_ACCESS_SIZE_MASK (REGION_ACCESS_SIZE_LIMIT - 1)
|
||
|
|
||
|
#endif /* _HW_H_ */
|