132 lines
2.7 KiB
Plaintext
132 lines
2.7 KiB
Plaintext
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
|
/dts-v1/;
|
|
|
|
#include "bcm4709.dtsi"
|
|
#include "bcm5301x-nand-cs0-bch8.dtsi"
|
|
#include <dt-bindings/leds/common.h>
|
|
#include <dt-bindings/input/input.h>
|
|
|
|
/ {
|
|
model = "D-Link DWL-8610AP";
|
|
compatible = "dlink,dwl-8610ap", "brcm,bcm53016", "brcm,bcm4708";
|
|
|
|
memory@0 {
|
|
device_type = "memory";
|
|
/* 512 MB RAM in 2 x Macronix D9PSH chips */
|
|
reg = <0x00000000 0x08000000>,
|
|
<0x88000000 0x08000000>;
|
|
};
|
|
|
|
leds {
|
|
compatible = "gpio-leds";
|
|
|
|
led-power {
|
|
function = LED_FUNCTION_POWER;
|
|
color = <LED_COLOR_ID_GREEN>;
|
|
gpios = <&chipcommon 0 GPIO_ACTIVE_LOW>;
|
|
default-state = "on";
|
|
};
|
|
|
|
led-diag {
|
|
/* Actually "diag" unclear what this means */
|
|
function = LED_FUNCTION_INDICATOR;
|
|
color = <LED_COLOR_ID_RED>;
|
|
gpios = <&chipcommon 1 GPIO_ACTIVE_LOW>;
|
|
default-state = "on";
|
|
linux,default-trigger = "heartbeat";
|
|
};
|
|
|
|
led-wlan-2g {
|
|
function = LED_FUNCTION_WLAN;
|
|
color = <LED_COLOR_ID_GREEN>;
|
|
gpios = <&chipcommon 5 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
led-wlan-5g {
|
|
function = LED_FUNCTION_WLAN;
|
|
color = <LED_COLOR_ID_GREEN>;
|
|
gpios = <&chipcommon 8 GPIO_ACTIVE_LOW>;
|
|
};
|
|
};
|
|
|
|
gpio_keys {
|
|
compatible = "gpio-keys";
|
|
|
|
button-reset {
|
|
debounce-interval = <100>;
|
|
wakeup-source;
|
|
linux,code = <KEY_RESTART>;
|
|
label = "reset";
|
|
/* This GPIO is actually stored in NVRAM, but it's not gonna change */
|
|
gpios = <&chipcommon 4 GPIO_ACTIVE_LOW>;
|
|
};
|
|
};
|
|
|
|
/*
|
|
* Flash memory at 0x1e000000-0x1fffffff
|
|
* Macronix 32 64KB blocks; total size 2MB, same that can be
|
|
* found attached to the spi_nor SPI controller.
|
|
*/
|
|
nvram@1e080000 {
|
|
compatible = "brcm,nvram";
|
|
reg = <0x1e080000 0x00020000>;
|
|
|
|
et0macaddr: et0macaddr {
|
|
};
|
|
|
|
et1macaddr: et1macaddr {
|
|
};
|
|
};
|
|
};
|
|
|
|
&gmac0 {
|
|
nvmem-cells = <&et0macaddr>;
|
|
nvmem-cell-names = "mac-address";
|
|
};
|
|
|
|
&gmac1 {
|
|
nvmem-cells = <&et1macaddr>;
|
|
nvmem-cell-names = "mac-address";
|
|
};
|
|
|
|
&spi_nor {
|
|
/* Serial SPI NOR Flash MX 25L1606E */
|
|
status = "okay";
|
|
};
|
|
|
|
&nandcs {
|
|
/*
|
|
* Spansion S34ML01G100TFI00 128 MB NAND Flash memory
|
|
*
|
|
* This ECC is a bit unorthodox but it is what the stock firmware
|
|
* is using, so to be able to mount the original partitions
|
|
* this is necessary.
|
|
*/
|
|
nand-ecc-strength = <5>;
|
|
partitions {
|
|
compatible = "fixed-partitions";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
/* This is named nflash1.trx in CFE */
|
|
trx@0 {
|
|
label = "firmware";
|
|
reg = <0x00000000 0x02800000>;
|
|
compatible = "brcm,trx";
|
|
};
|
|
|
|
/* This is named nflash1.trx2 in CFE */
|
|
trx2@2800000 {
|
|
label = "firmware2";
|
|
reg = <0x02800000 0x02800000>;
|
|
compatible = "brcm,trx";
|
|
};
|
|
|
|
/* This is named nflash1.rwfs in CFE */
|
|
free@5000000 {
|
|
label = "free";
|
|
reg = <0x05000000 0x03000000>;
|
|
};
|
|
};
|
|
};
|