100 lines
2.2 KiB
Plaintext
100 lines
2.2 KiB
Plaintext
// SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause
|
|
/*
|
|
* Copyright (C) 2023 DH electronics GmbH
|
|
*
|
|
* DHCOM iMX6ULL variant:
|
|
* DHCM-iMX6ULL-C080-R051-F0409-SPI-E2-CAN2-SD-RTC-ADC-I-01D2
|
|
* DHCOR PCB number: 578-200 or newer
|
|
* DHCOM PCB number: 579-200 or newer
|
|
* DRC02 PCB number: 568-100 or newer (2nd ethernet by SoM)
|
|
*/
|
|
/dts-v1/;
|
|
|
|
#include "imx6ull-dhcom-som.dtsi"
|
|
#include "imx6ull-dhcom-som-cfg-sdcard.dtsi"
|
|
|
|
/ {
|
|
model = "DH electronics i.MX6ULL DHCOM on DRC02";
|
|
compatible = "dh,imx6ull-dhcom-drc02", "dh,imx6ull-dhcom-som",
|
|
"dh,imx6ull-dhcor-som", "fsl,imx6ull";
|
|
};
|
|
|
|
/*
|
|
* The signals for CAN2 TX and RX are routed to the DHCOM UART1 RTS/CTS pins.
|
|
* Therefore the UART RTS/CTS must be output on other DHCOM pins, see uart1
|
|
* node below.
|
|
*/
|
|
&can2 {
|
|
status = "okay";
|
|
};
|
|
|
|
&gpio1 {
|
|
gpio-line-names =
|
|
"", "", "", "",
|
|
"", "", "", "",
|
|
"", "", "", "DRC02-In2",
|
|
"", "", "", "",
|
|
"", "", "DHCOM-I", "",
|
|
"", "", "", "",
|
|
"", "", "", "",
|
|
"", "", "", "";
|
|
};
|
|
|
|
&gpio4 {
|
|
gpio-line-names =
|
|
"", "", "", "",
|
|
"", "", "", "",
|
|
"", "", "", "",
|
|
"", "", "", "",
|
|
"", "DRC02-HW0", "DRC02-HW1", "DHCOM-M",
|
|
"DRC02-HW2", "DHCOM-U", "DHCOM-T", "DHCOM-S",
|
|
"DHCOM-R", "DHCOM-Q", "DHCOM-P", "DHCOM-O",
|
|
"DHCOM-N", "", "", "";
|
|
/*
|
|
* NOTE: On DRC02, the RS485_RX_En is controlled by a separate
|
|
* GPIO line, however the i.MX6ULL UART driver assumes RX happens
|
|
* during TX anyway and that it only controls drive enable DE
|
|
* line. Hence, the RX is always enabled here.
|
|
*/
|
|
rs485-rx-en-hog {
|
|
gpio-hog;
|
|
gpios = <25 0>; /* GPIO Q */
|
|
line-name = "rs485-rx-en";
|
|
output-low;
|
|
};
|
|
};
|
|
|
|
&gpio5 {
|
|
gpio-line-names =
|
|
"DHCOM-A", "DHCOM-B", "DHCOM-C", "DRC02-Out2",
|
|
"DHCOM-E", "", "", "DRC02-Out1",
|
|
"DRC02-In1", "DHCOM-H", "", "",
|
|
"", "", "", "",
|
|
"", "", "", "",
|
|
"", "", "", "",
|
|
"", "", "", "",
|
|
"", "", "", "";
|
|
};
|
|
|
|
/* DHCOM I2C2 */
|
|
&i2c1 {
|
|
eeprom@56 {
|
|
compatible = "atmel,24c04";
|
|
reg = <0x56>;
|
|
pagesize = <16>;
|
|
};
|
|
};
|
|
|
|
&uart1 {
|
|
/delete-property/ uart-has-rtscts;
|
|
rts-gpios = <&gpio1 18 GPIO_ACTIVE_HIGH>; /* GPIO I */
|
|
cts-gpios = <&gpio4 19 GPIO_ACTIVE_HIGH>; /* GPIO M */
|
|
};
|
|
|
|
/* Use UART as RS485 */
|
|
&uart2 {
|
|
/delete-property/ uart-has-rtscts;
|
|
linux,rs485-enabled-at-boot-time;
|
|
rts-gpios = <&gpio4 26 GPIO_ACTIVE_HIGH>; /* GPIO P */
|
|
};
|