153 lines
2.3 KiB
Plaintext
153 lines
2.3 KiB
Plaintext
// SPDX-License-Identifier: GPL-2.0
|
|
/*
|
|
* Copyright (C) 2017 Centrum Embedded Systems, Jia-Bin Huang <jb@ces.com.tw>
|
|
* Copyright (C) 2018 Jonathan McDowell <noodles@earth.li>
|
|
*/
|
|
|
|
/dts-v1/;
|
|
#include "sun8i-h3.dtsi"
|
|
#include "sunxi-common-regulators.dtsi"
|
|
|
|
#include <dt-bindings/gpio/gpio.h>
|
|
#include <dt-bindings/input/input.h>
|
|
|
|
/ {
|
|
model = "MapleBoard MP130";
|
|
compatible = "mapleboard,mp130", "allwinner,sun8i-h3";
|
|
|
|
aliases {
|
|
ethernet0 = &emac;
|
|
serial0 = &uart0;
|
|
};
|
|
|
|
chosen {
|
|
stdout-path = "serial0:115200n8";
|
|
};
|
|
|
|
leds {
|
|
compatible = "gpio-leds";
|
|
|
|
pwr_led {
|
|
label = "mp130:orange:pwr";
|
|
gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>;
|
|
default-state = "on";
|
|
};
|
|
|
|
status_led {
|
|
label = "mp130:orange:status";
|
|
gpios = <&pio 0 10 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
};
|
|
|
|
gpio-keys {
|
|
compatible = "gpio-keys";
|
|
|
|
key-power {
|
|
label = "power";
|
|
linux,code = <KEY_POWER>;
|
|
gpios = <&r_pio 0 3 GPIO_ACTIVE_LOW>; /* PL3 */
|
|
};
|
|
|
|
key-user {
|
|
label = "user";
|
|
linux,code = <BTN_0>;
|
|
gpios = <&r_pio 0 4 GPIO_ACTIVE_LOW>;
|
|
};
|
|
};
|
|
};
|
|
|
|
&codec {
|
|
allwinner,audio-routing =
|
|
"Line Out", "LINEOUT",
|
|
"LINEIN", "Line In";
|
|
status = "okay";
|
|
};
|
|
|
|
&ehci1 {
|
|
status = "okay";
|
|
};
|
|
|
|
&ehci2 {
|
|
status = "okay";
|
|
};
|
|
|
|
&ehci3 {
|
|
status = "okay";
|
|
};
|
|
|
|
&emac {
|
|
phy-handle = <&int_mii_phy>;
|
|
phy-mode = "mii";
|
|
allwinner,leds-active-low;
|
|
status = "okay";
|
|
};
|
|
|
|
&ir {
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&r_ir_rx_pin>;
|
|
status = "okay";
|
|
};
|
|
|
|
&mmc0 {
|
|
vmmc-supply = <®_vcc3v3>;
|
|
bus-width = <4>;
|
|
cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */
|
|
status = "okay";
|
|
};
|
|
|
|
&mmc2 {
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&mmc2_8bit_pins>;
|
|
vmmc-supply = <®_vcc3v3>;
|
|
bus-width = <8>;
|
|
non-removable;
|
|
cap-mmc-hw-reset;
|
|
status = "okay";
|
|
};
|
|
|
|
&ohci1 {
|
|
status = "okay";
|
|
};
|
|
|
|
&ohci2 {
|
|
status = "okay";
|
|
};
|
|
|
|
&ohci3 {
|
|
status = "okay";
|
|
};
|
|
|
|
&uart0 {
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&uart0_pa_pins>;
|
|
status = "okay";
|
|
};
|
|
|
|
&uart1 {
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&uart1_pins>;
|
|
status = "disabled";
|
|
};
|
|
|
|
&uart2 {
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&uart2_pins>;
|
|
status = "disabled";
|
|
};
|
|
|
|
&uart3 {
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&uart3_pins>;
|
|
status = "disabled";
|
|
};
|
|
|
|
&usb_otg {
|
|
dr_mode = "peripheral";
|
|
status = "okay";
|
|
};
|
|
|
|
&usbphy {
|
|
/* USB VBUS is always on */
|
|
status = "okay";
|
|
};
|