144 lines
2.4 KiB
Plaintext
144 lines
2.4 KiB
Plaintext
// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
|
|
// Copyright (C) 2017 Jagan Teki <jteki@openedev.com>
|
|
|
|
/dts-v1/;
|
|
|
|
#include "sun50i-h5.dtsi"
|
|
|
|
#include <dt-bindings/gpio/gpio.h>
|
|
|
|
/ {
|
|
model = "OrangePi Zero Plus2";
|
|
compatible = "xunlong,orangepi-zero-plus2", "allwinner,sun50i-h5";
|
|
|
|
aliases {
|
|
serial0 = &uart0;
|
|
};
|
|
|
|
chosen {
|
|
stdout-path = "serial0:115200n8";
|
|
};
|
|
|
|
connector {
|
|
compatible = "hdmi-connector";
|
|
type = "a";
|
|
|
|
port {
|
|
hdmi_con_in: endpoint {
|
|
remote-endpoint = <&hdmi_out_con>;
|
|
};
|
|
};
|
|
};
|
|
|
|
leds {
|
|
compatible = "gpio-leds";
|
|
|
|
led-0 {
|
|
label = "orangepi:green:pwr";
|
|
gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>;
|
|
default-state = "on";
|
|
};
|
|
|
|
led-1 {
|
|
label = "orangepi:red:status";
|
|
gpios = <&pio 0 17 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
};
|
|
|
|
reg_vcc3v3: vcc3v3 {
|
|
compatible = "regulator-fixed";
|
|
regulator-name = "vcc3v3";
|
|
regulator-min-microvolt = <3300000>;
|
|
regulator-max-microvolt = <3300000>;
|
|
};
|
|
|
|
wifi_pwrseq: wifi_pwrseq {
|
|
compatible = "mmc-pwrseq-simple";
|
|
reset-gpios = <&pio 0 9 GPIO_ACTIVE_LOW>; /* PA9 */
|
|
post-power-on-delay-ms = <200>;
|
|
};
|
|
};
|
|
|
|
&de {
|
|
status = "okay";
|
|
};
|
|
|
|
&ehci0 {
|
|
status = "okay";
|
|
};
|
|
|
|
&hdmi {
|
|
status = "okay";
|
|
};
|
|
|
|
&hdmi_out {
|
|
hdmi_out_con: endpoint {
|
|
remote-endpoint = <&hdmi_con_in>;
|
|
};
|
|
};
|
|
|
|
&mmc0 {
|
|
vmmc-supply = <®_vcc3v3>;
|
|
bus-width = <4>;
|
|
cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>;
|
|
status = "okay";
|
|
};
|
|
|
|
&mmc1 {
|
|
vmmc-supply = <®_vcc3v3>;
|
|
vqmmc-supply = <®_vcc3v3>;
|
|
mmc-pwrseq = <&wifi_pwrseq>;
|
|
bus-width = <4>;
|
|
non-removable;
|
|
status = "okay";
|
|
|
|
brcmf: wifi@1 {
|
|
reg = <1>;
|
|
compatible = "brcm,bcm4329-fmac";
|
|
interrupt-parent = <&r_pio>;
|
|
interrupts = <0 7 IRQ_TYPE_LEVEL_LOW>; /* PL7 */
|
|
interrupt-names = "host-wake";
|
|
};
|
|
};
|
|
|
|
&mmc2 {
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&mmc2_8bit_pins>;
|
|
vmmc-supply = <®_vcc3v3>;
|
|
bus-width = <8>;
|
|
non-removable;
|
|
cap-mmc-hw-reset;
|
|
status = "okay";
|
|
};
|
|
|
|
&ohci0 {
|
|
status = "okay";
|
|
};
|
|
|
|
&uart0 {
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&uart0_pa_pins>;
|
|
status = "okay";
|
|
};
|
|
|
|
&uart1 {
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&uart1_pins>, <&uart1_rts_cts_pins>;
|
|
status = "okay";
|
|
};
|
|
|
|
&usb_otg {
|
|
/*
|
|
* According to schematics CN1 MicroUSB port can be used to take
|
|
* external 5V to power up the board VBUS. On the contrary CN1 MicroUSB
|
|
* port cannot provide power externally even if the board is powered
|
|
* via GPIO pins. It thus makes sense to force peripheral mode.
|
|
*/
|
|
dr_mode = "peripheral";
|
|
status = "okay";
|
|
};
|
|
|
|
&usbphy {
|
|
status = "okay";
|
|
};
|