153 lines
3.1 KiB
Plaintext
153 lines
3.1 KiB
Plaintext
// SPDX-License-Identifier: GPL-2.0
|
|
#include <dt-bindings/iio/qcom,spmi-vadc.h>
|
|
#include <dt-bindings/input/linux-event-codes.h>
|
|
#include <dt-bindings/interrupt-controller/irq.h>
|
|
#include <dt-bindings/spmi/spmi.h>
|
|
|
|
/ {
|
|
thermal-zones {
|
|
pm8994-thermal {
|
|
polling-delay-passive = <250>;
|
|
polling-delay = <1000>;
|
|
|
|
thermal-sensors = <&pm8994_temp>;
|
|
|
|
trips {
|
|
pm8994_alert0: pm8994-alert0 {
|
|
temperature = <95000>;
|
|
hysteresis = <2000>;
|
|
type = "passive";
|
|
};
|
|
pm8994_crit: pm8994-crit {
|
|
temperature = <125000>;
|
|
hysteresis = <2000>;
|
|
type = "critical";
|
|
};
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
&spmi_bus {
|
|
|
|
pmic@0 {
|
|
compatible = "qcom,pm8994", "qcom,spmi-pmic";
|
|
reg = <0x0 SPMI_USID>;
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
rtc@6000 {
|
|
compatible = "qcom,pm8941-rtc";
|
|
reg = <0x6000>, <0x6100>;
|
|
reg-names = "rtc", "alarm";
|
|
interrupts = <0x0 0x61 0x1 IRQ_TYPE_EDGE_RISING>;
|
|
};
|
|
|
|
pm8994_pon: pon@800 {
|
|
compatible = "qcom,pm8916-pon";
|
|
reg = <0x800>;
|
|
mode-bootloader = <0x2>;
|
|
mode-recovery = <0x1>;
|
|
|
|
pwrkey {
|
|
compatible = "qcom,pm8941-pwrkey";
|
|
interrupts = <0x0 0x8 0 IRQ_TYPE_EDGE_BOTH>;
|
|
debounce = <15625>;
|
|
bias-pull-up;
|
|
linux,code = <KEY_POWER>;
|
|
};
|
|
|
|
pm8994_resin: resin {
|
|
compatible = "qcom,pm8941-resin";
|
|
interrupts = <0x0 0x8 1 IRQ_TYPE_EDGE_BOTH>;
|
|
debounce = <15625>;
|
|
bias-pull-up;
|
|
status = "disabled";
|
|
};
|
|
};
|
|
|
|
pm8994_temp: temp-alarm@2400 {
|
|
compatible = "qcom,spmi-temp-alarm";
|
|
reg = <0x2400>;
|
|
interrupts = <0x0 0x24 0x0 IRQ_TYPE_EDGE_RISING>;
|
|
io-channels = <&pm8994_vadc VADC_DIE_TEMP>;
|
|
io-channel-names = "thermal";
|
|
#thermal-sensor-cells = <0>;
|
|
};
|
|
|
|
pm8994_vadc: adc@3100 {
|
|
compatible = "qcom,spmi-vadc";
|
|
reg = <0x3100>;
|
|
interrupts = <0x0 0x31 0x0 IRQ_TYPE_EDGE_RISING>;
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
#io-channel-cells = <1>;
|
|
|
|
adc-chan@7 {
|
|
reg = <VADC_VSYS>;
|
|
qcom,pre-scaling = <1 3>;
|
|
label = "vph_pwr";
|
|
};
|
|
adc-chan@8 {
|
|
reg = <VADC_DIE_TEMP>;
|
|
label = "die_temp";
|
|
};
|
|
adc-chan@9 {
|
|
reg = <VADC_REF_625MV>;
|
|
label = "ref_625mv";
|
|
};
|
|
adc-chan@a {
|
|
reg = <VADC_REF_1250MV>;
|
|
label = "ref_1250mv";
|
|
};
|
|
adc-chan@e {
|
|
reg = <VADC_GND_REF>;
|
|
};
|
|
adc-chan@f {
|
|
reg = <VADC_VDD_VADC>;
|
|
};
|
|
};
|
|
|
|
pm8994_gpios: gpio@c000 {
|
|
compatible = "qcom,pm8994-gpio", "qcom,spmi-gpio";
|
|
reg = <0xc000>;
|
|
gpio-controller;
|
|
gpio-ranges = <&pm8994_gpios 0 0 22>;
|
|
#gpio-cells = <2>;
|
|
interrupt-controller;
|
|
#interrupt-cells = <2>;
|
|
};
|
|
|
|
pm8994_mpps: mpps@a000 {
|
|
compatible = "qcom,pm8994-mpp", "qcom,spmi-mpp";
|
|
reg = <0xa000>;
|
|
gpio-controller;
|
|
#gpio-cells = <2>;
|
|
gpio-ranges = <&pm8994_mpps 0 0 8>;
|
|
interrupt-controller;
|
|
#interrupt-cells = <2>;
|
|
};
|
|
};
|
|
|
|
pmic@1 {
|
|
compatible = "qcom,pm8994", "qcom,spmi-pmic";
|
|
reg = <0x1 SPMI_USID>;
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
pm8994_lpg: pwm {
|
|
compatible = "qcom,pm8994-lpg";
|
|
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
#pwm-cells = <2>;
|
|
|
|
status = "disabled";
|
|
};
|
|
|
|
pm8994_spmi_regulators: regulators {
|
|
compatible = "qcom,pm8994-regulators";
|
|
};
|
|
};
|
|
};
|