521 lines
12 KiB
Plaintext
521 lines
12 KiB
Plaintext
// SPDX-License-Identifier: GPL-2.0+
|
|
/*
|
|
* Turris 1.x Device Tree Source
|
|
*
|
|
* Copyright 2013 - 2022 CZ.NIC z.s.p.o. (http://www.nic.cz/)
|
|
*
|
|
* Pinout, Schematics and Altium hardware design files are open source
|
|
* and available at: https://docs.turris.cz/hw/turris-1x/turris-1x/
|
|
*/
|
|
|
|
#include <dt-bindings/gpio/gpio.h>
|
|
#include <dt-bindings/interrupt-controller/irq.h>
|
|
#include <dt-bindings/leds/common.h>
|
|
/include/ "fsl/p2020si-pre.dtsi"
|
|
|
|
/ {
|
|
model = "Turris 1.x";
|
|
compatible = "cznic,turris1x", "fsl,P2020RDB-PC"; /* fsl,P2020RDB-PC is required for booting Linux */
|
|
|
|
aliases {
|
|
ethernet0 = &enet0;
|
|
ethernet1 = &enet1;
|
|
ethernet2 = &enet2;
|
|
serial0 = &serial0;
|
|
serial1 = &serial1;
|
|
pci0 = &pci0;
|
|
pci1 = &pci1;
|
|
pci2 = &pci2;
|
|
spi0 = &spi0;
|
|
};
|
|
|
|
memory {
|
|
device_type = "memory";
|
|
};
|
|
|
|
soc: soc@ffe00000 {
|
|
ranges = <0x0 0x0 0xffe00000 0x00100000>;
|
|
|
|
i2c@3000 {
|
|
/* PCA9557PW GPIO controller for boot config */
|
|
gpio-controller@18 {
|
|
compatible = "nxp,pca9557";
|
|
label = "bootcfg";
|
|
reg = <0x18>;
|
|
#gpio-cells = <2>;
|
|
gpio-controller;
|
|
polarity = <0x00>;
|
|
};
|
|
|
|
/* STM32F030R8T6 MCU for power control */
|
|
power-control@2a {
|
|
/*
|
|
* Turris Power Control firmware runs on STM32F0 MCU.
|
|
* This firmware is open source and available at:
|
|
* https://gitlab.nic.cz/turris/hw/turris_power_control
|
|
*/
|
|
reg = <0x2a>;
|
|
};
|
|
|
|
/* DDR3 SPD/EEPROM PSWP instruction */
|
|
eeprom@32 {
|
|
reg = <0x32>;
|
|
};
|
|
|
|
/* SA56004ED temperature control */
|
|
temperature-sensor@4c {
|
|
compatible = "nxp,sa56004";
|
|
reg = <0x4c>;
|
|
interrupt-parent = <&gpio>;
|
|
interrupts = <12 IRQ_TYPE_LEVEL_LOW>, /* GPIO12 - ALERT pin */
|
|
<13 IRQ_TYPE_LEVEL_LOW>; /* GPIO13 - CRIT pin */
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
/* Local temperature sensor (SA56004ED internal) */
|
|
channel@0 {
|
|
reg = <0>;
|
|
label = "board";
|
|
};
|
|
|
|
/* Remote temperature sensor (D+/D- connected to P2020 CPU Temperature Diode) */
|
|
channel@1 {
|
|
reg = <1>;
|
|
label = "cpu";
|
|
};
|
|
};
|
|
|
|
/* DDR3 SPD/EEPROM */
|
|
eeprom@52 {
|
|
compatible = "atmel,spd";
|
|
reg = <0x52>;
|
|
};
|
|
|
|
/* MCP79402-I/ST Protected EEPROM */
|
|
eeprom@57 {
|
|
reg = <0x57>;
|
|
};
|
|
|
|
/* ATSHA204-TH-DA-T crypto module */
|
|
crypto@64 {
|
|
compatible = "atmel,atsha204";
|
|
reg = <0x64>;
|
|
};
|
|
|
|
/* IDT6V49205BNLGI clock generator */
|
|
clock-generator@69 {
|
|
compatible = "idt,6v49205b";
|
|
reg = <0x69>;
|
|
};
|
|
|
|
/* MCP79402-I/ST RTC */
|
|
rtc@6f {
|
|
compatible = "microchip,mcp7940x";
|
|
reg = <0x6f>;
|
|
interrupt-parent = <&gpio>;
|
|
interrupts = <14 0>; /* GPIO14 - MFP pin */
|
|
};
|
|
};
|
|
|
|
/* SPI on connector P1 */
|
|
spi0: spi@7000 {
|
|
};
|
|
|
|
gpio: gpio-controller@fc00 {
|
|
#interrupt-cells = <2>;
|
|
interrupt-controller;
|
|
};
|
|
|
|
/* Connected to SMSC USB2412-DZK 2-Port USB 2.0 Hub Controller */
|
|
usb@22000 {
|
|
phy_type = "ulpi";
|
|
dr_mode = "host";
|
|
};
|
|
|
|
enet0: ethernet@24000 {
|
|
/* Connected to port 6 of QCA8337N-AL3C switch */
|
|
phy-connection-type = "rgmii-id";
|
|
|
|
fixed-link {
|
|
speed = <1000>;
|
|
full-duplex;
|
|
};
|
|
};
|
|
|
|
mdio@24520 {
|
|
/* KSZ9031RNXCA ethernet phy for WAN port */
|
|
phy: ethernet-phy@7 {
|
|
interrupts = <3 1 0 0>;
|
|
reg = <0x7>;
|
|
};
|
|
|
|
/* QCA8337N-AL3C switch with integrated ethernet PHYs for LAN ports */
|
|
switch@10 {
|
|
compatible = "qca,qca8337";
|
|
interrupts = <2 1 0 0>;
|
|
reg = <0x10>;
|
|
|
|
ports {
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
port@0 {
|
|
reg = <0>;
|
|
label = "cpu";
|
|
ethernet = <&enet1>;
|
|
phy-mode = "rgmii-id";
|
|
|
|
fixed-link {
|
|
speed = <1000>;
|
|
full-duplex;
|
|
};
|
|
};
|
|
|
|
port@1 {
|
|
reg = <1>;
|
|
label = "lan5";
|
|
};
|
|
|
|
port@2 {
|
|
reg = <2>;
|
|
label = "lan4";
|
|
};
|
|
|
|
port@3 {
|
|
reg = <3>;
|
|
label = "lan3";
|
|
};
|
|
|
|
port@4 {
|
|
reg = <4>;
|
|
label = "lan2";
|
|
};
|
|
|
|
port@5 {
|
|
reg = <5>;
|
|
label = "lan1";
|
|
};
|
|
|
|
port@6 {
|
|
reg = <6>;
|
|
label = "cpu";
|
|
ethernet = <&enet0>;
|
|
phy-mode = "rgmii-id";
|
|
|
|
fixed-link {
|
|
speed = <1000>;
|
|
full-duplex;
|
|
};
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
ptp_clock@24e00 {
|
|
fsl,tclk-period = <5>;
|
|
fsl,tmr-prsc = <200>;
|
|
fsl,tmr-add = <0xcccccccd>;
|
|
fsl,tmr-fiper1 = <0x3b9ac9fb>;
|
|
fsl,tmr-fiper2 = <0x0001869b>;
|
|
fsl,max-adj = <249999999>;
|
|
};
|
|
|
|
enet1: ethernet@25000 {
|
|
/* Connected to port 0 of QCA8337N-AL3C switch */
|
|
phy-connection-type = "rgmii-id";
|
|
|
|
fixed-link {
|
|
speed = <1000>;
|
|
full-duplex;
|
|
};
|
|
};
|
|
|
|
mdio@25520 {
|
|
status = "disabled";
|
|
};
|
|
|
|
enet2: ethernet@26000 {
|
|
/* Connected to KSZ9031RNXCA ethernet phy (WAN port) */
|
|
label = "wan";
|
|
phy-handle = <&phy>;
|
|
phy-connection-type = "rgmii-id";
|
|
};
|
|
|
|
mdio@26520 {
|
|
status = "disabled";
|
|
};
|
|
|
|
sdhc@2e000 {
|
|
bus-width = <4>;
|
|
cd-gpios = <&gpio 8 GPIO_ACTIVE_LOW>;
|
|
};
|
|
};
|
|
|
|
lbc: localbus@ffe05000 {
|
|
reg = <0 0xffe05000 0 0x1000>;
|
|
|
|
ranges = <0x0 0x0 0x0 0xef000000 0x01000000>, /* NOR */
|
|
<0x1 0x0 0x0 0xff800000 0x00040000>, /* NAND */
|
|
<0x3 0x0 0x0 0xffa00000 0x00020000>; /* CPLD */
|
|
|
|
/* S29GL128P90TFIR10 NOR */
|
|
nor@0,0 {
|
|
compatible = "cfi-flash";
|
|
reg = <0x0 0x0 0x01000000>;
|
|
bank-width = <2>;
|
|
device-width = <1>;
|
|
|
|
partitions {
|
|
compatible = "fixed-partitions";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
partition@0 {
|
|
/* 128 kB for Device Tree Blob */
|
|
reg = <0x00000000 0x00020000>;
|
|
label = "dtb";
|
|
};
|
|
|
|
partition@20000 {
|
|
/* 1.7 MB for Linux Kernel Image */
|
|
reg = <0x00020000 0x001a0000>;
|
|
label = "kernel";
|
|
};
|
|
|
|
partition@1c0000 {
|
|
/* 1.5 MB for Rescue JFFS2 Root File System */
|
|
reg = <0x001c0000 0x00180000>;
|
|
label = "rescue";
|
|
};
|
|
|
|
partition@340000 {
|
|
/* 11 MB for TAR.XZ Archive with Factory content of NAND Root File System */
|
|
reg = <0x00340000 0x00b00000>;
|
|
label = "factory";
|
|
};
|
|
|
|
partition@e40000 {
|
|
/* 768 kB for Certificates JFFS2 File System */
|
|
reg = <0x00e40000 0x000c0000>;
|
|
label = "certificates";
|
|
};
|
|
|
|
/* free unused space 0x00f00000-0x00f20000 */
|
|
|
|
partition@f20000 {
|
|
/* 128 kB for U-Boot Environment Variables */
|
|
reg = <0x00f20000 0x00020000>;
|
|
label = "u-boot-env";
|
|
};
|
|
|
|
partition@f40000 {
|
|
/* 768 kB for U-Boot Bootloader Image */
|
|
reg = <0x00f40000 0x000c0000>;
|
|
label = "u-boot";
|
|
};
|
|
};
|
|
};
|
|
|
|
/* MT29F2G08ABAEAWP:E NAND */
|
|
nand@1,0 {
|
|
compatible = "fsl,p2020-fcm-nand", "fsl,elbc-fcm-nand";
|
|
reg = <0x1 0x0 0x00040000>;
|
|
nand-ecc-mode = "soft";
|
|
nand-ecc-algo = "bch";
|
|
|
|
partitions {
|
|
compatible = "fixed-partitions";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
partition@0 {
|
|
/* 256 MB for UBI with one volume: UBIFS Root File System */
|
|
reg = <0x00000000 0x10000000>;
|
|
label = "rootfs";
|
|
};
|
|
};
|
|
};
|
|
|
|
/* LCMXO1200C-3FTN256C FPGA */
|
|
cpld@3,0 {
|
|
/*
|
|
* Turris CPLD firmware which runs on this Lattice FPGA,
|
|
* is extended version of P1021RDB-PC CPLD v4.1 firmware.
|
|
* It is backward compatible with its original version
|
|
* and the only extension is support for Turris LEDs.
|
|
* Turris CPLD firmware is open source and available at:
|
|
* https://gitlab.nic.cz/turris/hw/turris_cpld/-/blob/master/CZ_NIC_Router_CPLD.v
|
|
*/
|
|
compatible = "cznic,turris1x-cpld", "fsl,p1021rdb-pc-cpld", "simple-bus", "syscon";
|
|
reg = <0x3 0x0 0x30>;
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
ranges = <0x0 0x3 0x0 0x00020000>;
|
|
|
|
/* MAX6370KA+T watchdog */
|
|
watchdog@2 {
|
|
/*
|
|
* CPLD firmware maps SET0, SET1 and SET2
|
|
* input logic of MAX6370KA+T chip to CPLD
|
|
* memory space at byte offset 0x2. WDI
|
|
* input logic is outside of the CPLD and
|
|
* connected via external GPIO.
|
|
*/
|
|
compatible = "maxim,max6370";
|
|
reg = <0x02 0x01>;
|
|
gpios = <&gpio 11 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
reboot@d {
|
|
/*
|
|
* CPLD firmware which manages system reset and
|
|
* watchdog registers has bugs. It does not
|
|
* autoclear system reset register after change
|
|
* and watchdog ignores reset line on immediate
|
|
* succeeding reset cycle triggered by watchdog.
|
|
* These bugs have to be workarounded in U-Boot
|
|
* bootloader. So use system reset via syscon as
|
|
* a last resort because older U-Boot versions
|
|
* do not have workaround for watchdog.
|
|
*
|
|
* Reset method via rstcr's global-utilities
|
|
* (the preferred one) has priority level 128,
|
|
* watchdog has priority level 0 and default
|
|
* syscon-reboot priority level is 192.
|
|
*
|
|
* So define syscon-reboot with custom priority
|
|
* level 64 (between rstcr and watchdog) because
|
|
* rstcr should stay as default preferred reset
|
|
* method and reset via watchdog is more broken
|
|
* than system reset via syscon.
|
|
*/
|
|
compatible = "syscon-reboot";
|
|
reg = <0x0d 0x01>;
|
|
offset = <0x0d>;
|
|
mask = <0x01>;
|
|
value = <0x01>;
|
|
priority = <64>;
|
|
};
|
|
|
|
led-controller@13 {
|
|
/*
|
|
* LEDs are controlled by CPLD firmware.
|
|
* All five LAN LEDs share common RGB settings
|
|
* and so it is not possible to set different
|
|
* colors on different LAN ports.
|
|
*/
|
|
compatible = "cznic,turris1x-leds";
|
|
reg = <0x13 0x1d>;
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
multi-led@0 {
|
|
reg = <0x0>;
|
|
color = <LED_COLOR_ID_RGB>;
|
|
function = LED_FUNCTION_WAN;
|
|
};
|
|
|
|
multi-led@1 {
|
|
reg = <0x1>;
|
|
color = <LED_COLOR_ID_RGB>;
|
|
function = LED_FUNCTION_LAN;
|
|
function-enumerator = <5>;
|
|
};
|
|
|
|
multi-led@2 {
|
|
reg = <0x2>;
|
|
color = <LED_COLOR_ID_RGB>;
|
|
function = LED_FUNCTION_LAN;
|
|
function-enumerator = <4>;
|
|
};
|
|
|
|
multi-led@3 {
|
|
reg = <0x3>;
|
|
color = <LED_COLOR_ID_RGB>;
|
|
function = LED_FUNCTION_LAN;
|
|
function-enumerator = <3>;
|
|
};
|
|
|
|
multi-led@4 {
|
|
reg = <0x4>;
|
|
color = <LED_COLOR_ID_RGB>;
|
|
function = LED_FUNCTION_LAN;
|
|
function-enumerator = <2>;
|
|
};
|
|
|
|
multi-led@5 {
|
|
reg = <0x5>;
|
|
color = <LED_COLOR_ID_RGB>;
|
|
function = LED_FUNCTION_LAN;
|
|
function-enumerator = <1>;
|
|
};
|
|
|
|
multi-led@6 {
|
|
reg = <0x6>;
|
|
color = <LED_COLOR_ID_RGB>;
|
|
function = LED_FUNCTION_WLAN;
|
|
};
|
|
|
|
multi-led@7 {
|
|
reg = <0x7>;
|
|
color = <LED_COLOR_ID_RGB>;
|
|
function = LED_FUNCTION_POWER;
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
pci2: pcie@ffe08000 {
|
|
/*
|
|
* PCIe bus for on-board TUSB7340RKM USB 3.0 xHCI controller.
|
|
* This xHCI controller is available only on Turris 1.1 boards.
|
|
* Turris 1.0 boards have nothing connected to this PCIe bus,
|
|
* so system would see only PCIe Root Port of this PCIe Root
|
|
* Complex. TUSB7340RKM xHCI controller has four SuperSpeed
|
|
* channels. Channel 0 is connected to the front USB 3.0 port,
|
|
* channel 1 (but only USB 2.0 subset) to USB 2.0 pins on mPCIe
|
|
* slot 1 (CN5), channels 2 and 3 to connector P600.
|
|
*
|
|
* P2020 PCIe Root Port uses 1MB of PCIe MEM and xHCI controller
|
|
* uses 64kB + 8kB of PCIe MEM. No PCIe IO is used or required.
|
|
* So allocate 2MB of PCIe MEM for this PCIe bus.
|
|
*/
|
|
reg = <0 0xffe08000 0 0x1000>;
|
|
ranges = <0x02000000 0x0 0xc0000000 0 0xc0000000 0x0 0x00200000>, /* MEM */
|
|
<0x01000000 0x0 0x00000000 0 0xffc20000 0x0 0x00010000>; /* IO */
|
|
|
|
pcie@0 {
|
|
ranges;
|
|
};
|
|
};
|
|
|
|
pci1: pcie@ffe09000 {
|
|
/* PCIe bus on mPCIe slot 2 (CN6) for expansion mPCIe card */
|
|
reg = <0 0xffe09000 0 0x1000>;
|
|
ranges = <0x02000000 0x0 0xa0000000 0 0xa0000000 0x0 0x20000000>, /* MEM */
|
|
<0x01000000 0x0 0x00000000 0 0xffc10000 0x0 0x00010000>; /* IO */
|
|
|
|
pcie@0 {
|
|
ranges;
|
|
};
|
|
};
|
|
|
|
pci0: pcie@ffe0a000 {
|
|
/*
|
|
* PCIe bus on mPCIe slot 1 (CN5) for expansion mPCIe card.
|
|
* Turris 1.1 boards have in this mPCIe slot additional USB 2.0
|
|
* pins via channel 1 of TUSB7340RKM xHCI controller and also
|
|
* additional SIM card slot, both for USB-based WWAN cards.
|
|
*/
|
|
reg = <0 0xffe0a000 0 0x1000>;
|
|
ranges = <0x02000000 0x0 0x80000000 0 0x80000000 0x0 0x20000000>, /* MEM */
|
|
<0x01000000 0x0 0x00000000 0 0xffc00000 0x0 0x00010000>; /* IO */
|
|
|
|
pcie@0 {
|
|
ranges;
|
|
};
|
|
};
|
|
};
|
|
|
|
/include/ "fsl/p2020si-post.dtsi"
|