kvj
/
linux-zen-server
1
0
Fork 0
Code Issues Pull Requests Packages Projects Releases Wiki Activity
linux-zen-server/drivers/i2c/busses/i2c-xiic.c

1408 lines
39 KiB
C
Raw Permalink Blame History

// SPDX-License-Identifier: GPL-2.0-only
/*
* i2c-xiic.c
* Copyright (c) 2002-2007 Xilinx Inc.
* Copyright (c) 2009-2010 Intel Corporation
*
* This code was implemented by Mocean Laboratories AB when porting linux
* to the automotive development board Russellville. The copyright holder
* as seen in the header is Intel corporation.
* Mocean Laboratories forked off the GNU/Linux platform work into a
* separate company called Pelagicore AB, which committed the code to the
* kernel.
*/
/* Supports:
* Xilinx IIC
*/
#include <linux/kernel.h>
#include <linux/module.h>
#include <linux/errno.h>
#include <linux/err.h>
#include <linux/delay.h>
#include <linux/platform_device.h>
#include <linux/i2c.h>
#include <linux/interrupt.h>
#include <linux/completion.h>
#include <linux/platform_data/i2c-xiic.h>
#include <linux/io.h>
#include <linux/slab.h>
#include <linux/of.h>
#include <linux/clk.h>
#include <linux/pm_runtime.h>
#define DRIVER_NAME "xiic-i2c"
#define DYNAMIC_MODE_READ_BROKEN_BIT BIT(0)
#define SMBUS_BLOCK_READ_MIN_LEN 3
enum xilinx_i2c_state {
STATE_DONE,
STATE_ERROR,
STATE_START
};
enum xiic_endian {
LITTLE,
BIG
};
enum i2c_scl_freq {
REG_VALUES_100KHZ = 0,
REG_VALUES_400KHZ = 1,
REG_VALUES_1MHZ = 2
};
/**
* struct xiic_i2c - Internal representation of the XIIC I2C bus
* @dev: Pointer to device structure
* @base: Memory base of the HW registers
* @completion: Completion for callers
* @adap: Kernel adapter representation
* @tx_msg: Messages from above to be sent
* @lock: Mutual exclusion
* @tx_pos: Current pos in TX message
* @nmsgs: Number of messages in tx_msg
* @rx_msg: Current RX message
* @rx_pos: Position within current RX message
* @endianness: big/little-endian byte order
* @clk: Pointer to AXI4-lite input clock
* @state: See STATE_
* @singlemaster: Indicates bus is single master
* @dynamic: Mode of controller
* @prev_msg_tx: Previous message is Tx
* @quirks: To hold platform specific bug info
* @smbus_block_read: Flag to handle block read
* @input_clk: Input clock to I2C controller
* @i2c_clk: I2C SCL frequency
*/
struct xiic_i2c {
struct device *dev;
void __iomem *base;
struct completion completion;
struct i2c_adapter adap;
struct i2c_msg *tx_msg;
struct mutex lock;
unsigned int tx_pos;
unsigned int nmsgs;
struct i2c_msg *rx_msg;
int rx_pos;
enum xiic_endian endianness;
struct clk *clk;
enum xilinx_i2c_state state;
bool singlemaster;
bool dynamic;
bool prev_msg_tx;
u32 quirks;
bool smbus_block_read;
unsigned long input_clk;
unsigned int i2c_clk;
};
struct xiic_version_data {
u32 quirks;
};
/**
* struct timing_regs - AXI I2C timing registers that depend on I2C spec
* @tsusta: setup time for a repeated START condition
* @tsusto: setup time for a STOP condition
* @thdsta: hold time for a repeated START condition
* @tsudat: setup time for data
* @tbuf: bus free time between STOP and START
*/
struct timing_regs {
unsigned int tsusta;
unsigned int tsusto;
unsigned int thdsta;
unsigned int tsudat;
unsigned int tbuf;
};
/* Reg values in ns derived from I2C spec and AXI I2C PG for different frequencies */
static const struct timing_regs timing_reg_values[] = {
{ 5700, 5000, 4300, 550, 5000 }, /* Reg values for 100KHz */
{ 900, 900, 900, 400, 1600 }, /* Reg values for 400KHz */
{ 380, 380, 380, 170, 620 }, /* Reg values for 1MHz */
};
#define XIIC_MSB_OFFSET 0
#define XIIC_REG_OFFSET (0x100 + XIIC_MSB_OFFSET)
/*
* Register offsets in bytes from RegisterBase. Three is added to the
* base offset to access LSB (IBM style) of the word
*/
#define XIIC_CR_REG_OFFSET (0x00 + XIIC_REG_OFFSET) /* Control Register */
#define XIIC_SR_REG_OFFSET (0x04 + XIIC_REG_OFFSET) /* Status Register */
#define XIIC_DTR_REG_OFFSET (0x08 + XIIC_REG_OFFSET) /* Data Tx Register */
#define XIIC_DRR_REG_OFFSET (0x0C + XIIC_REG_OFFSET) /* Data Rx Register */
#define XIIC_ADR_REG_OFFSET (0x10 + XIIC_REG_OFFSET) /* Address Register */
#define XIIC_TFO_REG_OFFSET (0x14 + XIIC_REG_OFFSET) /* Tx FIFO Occupancy */
#define XIIC_RFO_REG_OFFSET (0x18 + XIIC_REG_OFFSET) /* Rx FIFO Occupancy */
#define XIIC_TBA_REG_OFFSET (0x1C + XIIC_REG_OFFSET) /* 10 Bit Address reg */
#define XIIC_RFD_REG_OFFSET (0x20 + XIIC_REG_OFFSET) /* Rx FIFO Depth reg */
#define XIIC_GPO_REG_OFFSET (0x24 + XIIC_REG_OFFSET) /* Output Register */
/*
* Timing register offsets from RegisterBase. These are used only for
* setting i2c clock frequency for the line.
*/
#define XIIC_TSUSTA_REG_OFFSET (0x28 + XIIC_REG_OFFSET) /* TSUSTA Register */
#define XIIC_TSUSTO_REG_OFFSET (0x2C + XIIC_REG_OFFSET) /* TSUSTO Register */
#define XIIC_THDSTA_REG_OFFSET (0x30 + XIIC_REG_OFFSET) /* THDSTA Register */
#define XIIC_TSUDAT_REG_OFFSET (0x34 + XIIC_REG_OFFSET) /* TSUDAT Register */
#define XIIC_TBUF_REG_OFFSET (0x38 + XIIC_REG_OFFSET) /* TBUF Register */
#define XIIC_THIGH_REG_OFFSET (0x3C + XIIC_REG_OFFSET) /* THIGH Register */
#define XIIC_TLOW_REG_OFFSET (0x40 + XIIC_REG_OFFSET) /* TLOW Register */
#define XIIC_THDDAT_REG_OFFSET (0x44 + XIIC_REG_OFFSET) /* THDDAT Register */
/* Control Register masks */
#define XIIC_CR_ENABLE_DEVICE_MASK 0x01 /* Device enable = 1 */
#define XIIC_CR_TX_FIFO_RESET_MASK 0x02 /* Transmit FIFO reset=1 */
#define XIIC_CR_MSMS_MASK 0x04 /* Master starts Txing=1 */
#define XIIC_CR_DIR_IS_TX_MASK 0x08 /* Dir of tx. Txing=1 */
#define XIIC_CR_NO_ACK_MASK 0x10 /* Tx Ack. NO ack = 1 */
#define XIIC_CR_REPEATED_START_MASK 0x20 /* Repeated start = 1 */
#define XIIC_CR_GENERAL_CALL_MASK 0x40 /* Gen Call enabled = 1 */
/* Status Register masks */
#define XIIC_SR_GEN_CALL_MASK 0x01 /* 1=a mstr issued a GC */
#define XIIC_SR_ADDR_AS_SLAVE_MASK 0x02 /* 1=when addr as slave */
#define XIIC_SR_BUS_BUSY_MASK 0x04 /* 1 = bus is busy */
#define XIIC_SR_MSTR_RDING_SLAVE_MASK 0x08 /* 1=Dir: mstr <-- slave */
#define XIIC_SR_TX_FIFO_FULL_MASK 0x10 /* 1 = Tx FIFO full */
#define XIIC_SR_RX_FIFO_FULL_MASK 0x20 /* 1 = Rx FIFO full */
#define XIIC_SR_RX_FIFO_EMPTY_MASK 0x40 /* 1 = Rx FIFO empty */
#define XIIC_SR_TX_FIFO_EMPTY_MASK 0x80 /* 1 = Tx FIFO empty */
/* Interrupt Status Register masks Interrupt occurs when... */
#define XIIC_INTR_ARB_LOST_MASK 0x01 /* 1 = arbitration lost */
#define XIIC_INTR_TX_ERROR_MASK 0x02 /* 1=Tx error/msg complete */
#define XIIC_INTR_TX_EMPTY_MASK 0x04 /* 1 = Tx FIFO/reg empty */
#define XIIC_INTR_RX_FULL_MASK 0x08 /* 1=Rx FIFO/reg=OCY level */
#define XIIC_INTR_BNB_MASK 0x10 /* 1 = Bus not busy */
#define XIIC_INTR_AAS_MASK 0x20 /* 1 = when addr as slave */
#define XIIC_INTR_NAAS_MASK 0x40 /* 1 = not addr as slave */
#define XIIC_INTR_TX_HALF_MASK 0x80 /* 1 = TX FIFO half empty */
/* The following constants specify the depth of the FIFOs */
#define IIC_RX_FIFO_DEPTH 16 /* Rx fifo capacity */
#define IIC_TX_FIFO_DEPTH 16 /* Tx fifo capacity */
/* The following constants specify groups of interrupts that are typically
* enabled or disables at the same time
*/
#define XIIC_TX_INTERRUPTS \
(XIIC_INTR_TX_ERROR_MASK | XIIC_INTR_TX_EMPTY_MASK | XIIC_INTR_TX_HALF_MASK)
#define XIIC_TX_RX_INTERRUPTS (XIIC_INTR_RX_FULL_MASK | XIIC_TX_INTERRUPTS)
/*
* Tx Fifo upper bit masks.
*/
#define XIIC_TX_DYN_START_MASK 0x0100 /* 1 = Set dynamic start */
#define XIIC_TX_DYN_STOP_MASK 0x0200 /* 1 = Set dynamic stop */
/* Dynamic mode constants */
#define MAX_READ_LENGTH_DYNAMIC 255 /* Max length for dynamic read */
/*
* The following constants define the register offsets for the Interrupt
* registers. There are some holes in the memory map for reserved addresses
* to allow other registers to be added and still match the memory map of the
* interrupt controller registers
*/
#define XIIC_DGIER_OFFSET 0x1C /* Device Global Interrupt Enable Register */
#define XIIC_IISR_OFFSET 0x20 /* Interrupt Status Register */
#define XIIC_IIER_OFFSET 0x28 /* Interrupt Enable Register */
#define XIIC_RESETR_OFFSET 0x40 /* Reset Register */
#define XIIC_RESET_MASK 0xAUL
#define XIIC_PM_TIMEOUT 1000 /* ms */
/* timeout waiting for the controller to respond */
#define XIIC_I2C_TIMEOUT (msecs_to_jiffies(1000))
/* timeout waiting for the controller finish transfers */
#define XIIC_XFER_TIMEOUT (msecs_to_jiffies(10000))
/*
* The following constant is used for the device global interrupt enable
* register, to enable all interrupts for the device, this is the only bit
* in the register
*/
#define XIIC_GINTR_ENABLE_MASK 0x80000000UL
#define xiic_tx_space(i2c) ((i2c)->tx_msg->len - (i2c)->tx_pos)
#define xiic_rx_space(i2c) ((i2c)->rx_msg->len - (i2c)->rx_pos)
static int xiic_start_xfer(struct xiic_i2c *i2c, struct i2c_msg *msgs, int num);
static void __xiic_start_xfer(struct xiic_i2c *i2c);
/*
* For the register read and write functions, a little-endian and big-endian
* version are necessary. Endianness is detected during the probe function.
* Only the least significant byte [doublet] of the register are ever
* accessed. This requires an offset of 3 [2] from the base address for
* big-endian systems.
*/
static inline void xiic_setreg8(struct xiic_i2c *i2c, int reg, u8 value)
{
if (i2c->endianness == LITTLE)
iowrite8(value, i2c->base + reg);
else
iowrite8(value, i2c->base + reg + 3);
}
static inline u8 xiic_getreg8(struct xiic_i2c *i2c, int reg)
{
u8 ret;
if (i2c->endianness == LITTLE)
ret = ioread8(i2c->base + reg);
else
ret = ioread8(i2c->base + reg + 3);
return ret;
}
static inline void xiic_setreg16(struct xiic_i2c *i2c, int reg, u16 value)
{
if (i2c->endianness == LITTLE)
iowrite16(value, i2c->base + reg);
else
iowrite16be(value, i2c->base + reg + 2);
}
static inline void xiic_setreg32(struct xiic_i2c *i2c, int reg, int value)
{
if (i2c->endianness == LITTLE)
iowrite32(value, i2c->base + reg);
else
iowrite32be(value, i2c->base + reg);
}
static inline int xiic_getreg32(struct xiic_i2c *i2c, int reg)
{
u32 ret;
if (i2c->endianness == LITTLE)
ret = ioread32(i2c->base + reg);
else
ret = ioread32be(i2c->base + reg);
return ret;
}
static inline void xiic_irq_dis(struct xiic_i2c *i2c, u32 mask)
{
u32 ier = xiic_getreg32(i2c, XIIC_IIER_OFFSET);
xiic_setreg32(i2c, XIIC_IIER_OFFSET, ier & ~mask);
}
static inline void xiic_irq_en(struct xiic_i2c *i2c, u32 mask)
{
u32 ier = xiic_getreg32(i2c, XIIC_IIER_OFFSET);
xiic_setreg32(i2c, XIIC_IIER_OFFSET, ier | mask);
}
static inline void xiic_irq_clr(struct xiic_i2c *i2c, u32 mask)
{
u32 isr = xiic_getreg32(i2c, XIIC_IISR_OFFSET);
xiic_setreg32(i2c, XIIC_IISR_OFFSET, isr & mask);
}
static inline void xiic_irq_clr_en(struct xiic_i2c *i2c, u32 mask)
{
xiic_irq_clr(i2c, mask);
xiic_irq_en(i2c, mask);
}
static int xiic_clear_rx_fifo(struct xiic_i2c *i2c)
{
u8 sr;
unsigned long timeout;
timeout = jiffies + XIIC_I2C_TIMEOUT;
for (sr = xiic_getreg8(i2c, XIIC_SR_REG_OFFSET);
!(sr & XIIC_SR_RX_FIFO_EMPTY_MASK);
sr = xiic_getreg8(i2c, XIIC_SR_REG_OFFSET)) {
xiic_getreg8(i2c, XIIC_DRR_REG_OFFSET);
if (time_after(jiffies, timeout)) {
dev_err(i2c->dev, "Failed to clear rx fifo\n");
return -ETIMEDOUT;
}
}
return 0;
}
static int xiic_wait_tx_empty(struct xiic_i2c *i2c)
{
u8 isr;
unsigned long timeout;
timeout = jiffies + XIIC_I2C_TIMEOUT;
for (isr = xiic_getreg32(i2c, XIIC_IISR_OFFSET);
!(isr & XIIC_INTR_TX_EMPTY_MASK);
isr = xiic_getreg32(i2c, XIIC_IISR_OFFSET)) {
if (time_after(jiffies, timeout)) {
dev_err(i2c->dev, "Timeout waiting at Tx empty\n");
return -ETIMEDOUT;
}
}
return 0;
}
/**
* xiic_setclk - Sets the configured clock rate
* @i2c: Pointer to the xiic device structure
*
* The timing register values are calculated according to the input clock
* frequency and configured scl frequency. For details, please refer the
* AXI I2C PG and NXP I2C Spec.
* Supported frequencies are 100KHz, 400KHz and 1MHz.
*
* Return: 0 on success (Supported frequency selected or not configurable in SW)
* -EINVAL on failure (scl frequency not supported or THIGH is 0)
*/
static int xiic_setclk(struct xiic_i2c *i2c)
{
unsigned int clk_in_mhz;
unsigned int index = 0;
u32 reg_val;
dev_dbg(i2c->adap.dev.parent,
"%s entry, i2c->input_clk: %ld, i2c->i2c_clk: %d\n",
__func__, i2c->input_clk, i2c->i2c_clk);
/* If not specified in DT, do not configure in SW. Rely only on Vivado design */
if (!i2c->i2c_clk || !i2c->input_clk)
return 0;
clk_in_mhz = DIV_ROUND_UP(i2c->input_clk, 1000000);
switch (i2c->i2c_clk) {
case I2C_MAX_FAST_MODE_PLUS_FREQ:
index = REG_VALUES_1MHZ;
break;
case I2C_MAX_FAST_MODE_FREQ:
index = REG_VALUES_400KHZ;
break;
case I2C_MAX_STANDARD_MODE_FREQ:
index = REG_VALUES_100KHZ;
break;
default:
dev_warn(i2c->adap.dev.parent, "Unsupported scl frequency\n");
return -EINVAL;
}
/*
* Value to be stored in a register is the number of clock cycles required
* for the time duration. So the time is divided by the input clock time
* period to get the number of clock cycles required. Refer Xilinx AXI I2C
* PG document and I2C specification for further details.
*/
/* THIGH - Depends on SCL clock frequency(i2c_clk) as below */
reg_val = (DIV_ROUND_UP(i2c->input_clk, 2 * i2c->i2c_clk)) - 7;
if (reg_val == 0)
return -EINVAL;
xiic_setreg32(i2c, XIIC_THIGH_REG_OFFSET, reg_val - 1);
/* TLOW - Value same as THIGH */
xiic_setreg32(i2c, XIIC_TLOW_REG_OFFSET, reg_val - 1);
/* TSUSTA */
reg_val = (timing_reg_values[index].tsusta * clk_in_mhz) / 1000;
xiic_setreg32(i2c, XIIC_TSUSTA_REG_OFFSET, reg_val - 1);
/* TSUSTO */
reg_val = (timing_reg_values[index].tsusto * clk_in_mhz) / 1000;
xiic_setreg32(i2c, XIIC_TSUSTO_REG_OFFSET, reg_val - 1);
/* THDSTA */
reg_val = (timing_reg_values[index].thdsta * clk_in_mhz) / 1000;
xiic_setreg32(i2c, XIIC_THDSTA_REG_OFFSET, reg_val - 1);
/* TSUDAT */
reg_val = (timing_reg_values[index].tsudat * clk_in_mhz) / 1000;
xiic_setreg32(i2c, XIIC_TSUDAT_REG_OFFSET, reg_val - 1);
/* TBUF */
reg_val = (timing_reg_values[index].tbuf * clk_in_mhz) / 1000;
xiic_setreg32(i2c, XIIC_TBUF_REG_OFFSET, reg_val - 1);
/* THDDAT */
xiic_setreg32(i2c, XIIC_THDDAT_REG_OFFSET, 1);
return 0;
}
static int xiic_reinit(struct xiic_i2c *i2c)
{
int ret;
xiic_setreg32(i2c, XIIC_RESETR_OFFSET, XIIC_RESET_MASK);
ret = xiic_setclk(i2c);
if (ret)
return ret;
/* Set receive Fifo depth to maximum (zero based). */
xiic_setreg8(i2c, XIIC_RFD_REG_OFFSET, IIC_RX_FIFO_DEPTH - 1);
/* Reset Tx Fifo. */
xiic_setreg8(i2c, XIIC_CR_REG_OFFSET, XIIC_CR_TX_FIFO_RESET_MASK);
/* Enable IIC Device, remove Tx Fifo reset & disable general call. */
xiic_setreg8(i2c, XIIC_CR_REG_OFFSET, XIIC_CR_ENABLE_DEVICE_MASK);
/* make sure RX fifo is empty */
ret = xiic_clear_rx_fifo(i2c);
if (ret)
return ret;
/* Enable interrupts */
xiic_setreg32(i2c, XIIC_DGIER_OFFSET, XIIC_GINTR_ENABLE_MASK);
xiic_irq_clr_en(i2c, XIIC_INTR_ARB_LOST_MASK);
return 0;
}
static void xiic_deinit(struct xiic_i2c *i2c)
{
u8 cr;
xiic_setreg32(i2c, XIIC_RESETR_OFFSET, XIIC_RESET_MASK);
/* Disable IIC Device. */
cr = xiic_getreg8(i2c, XIIC_CR_REG_OFFSET);
xiic_setreg8(i2c, XIIC_CR_REG_OFFSET, cr & ~XIIC_CR_ENABLE_DEVICE_MASK);
}
static void xiic_smbus_block_read_setup(struct xiic_i2c *i2c)
{
u8 rxmsg_len, rfd_set = 0;
/*
* Clear the I2C_M_RECV_LEN flag to avoid setting
* message length again
*/
i2c->rx_msg->flags &= ~I2C_M_RECV_LEN;
/* Set smbus_block_read flag to identify in isr */
i2c->smbus_block_read = true;
/* Read byte from rx fifo and set message length */
rxmsg_len = xiic_getreg8(i2c, XIIC_DRR_REG_OFFSET);
i2c->rx_msg->buf[i2c->rx_pos++] = rxmsg_len;
/* Check if received length is valid */
if (rxmsg_len <= I2C_SMBUS_BLOCK_MAX) {
/* Set Receive fifo depth */
if (rxmsg_len > IIC_RX_FIFO_DEPTH) {
/*
* When Rx msg len greater than or equal to Rx fifo capacity
* Receive fifo depth should set to Rx fifo capacity minus 1
*/
rfd_set = IIC_RX_FIFO_DEPTH - 1;
i2c->rx_msg->len = rxmsg_len + 1;
} else if ((rxmsg_len == 1) ||
(rxmsg_len == 0)) {
/*
* Minimum of 3 bytes required to exit cleanly. 1 byte
* already received, Second byte is being received. Have
* to set NACK in read_rx before receiving the last byte
*/
rfd_set = 0;
i2c->rx_msg->len = SMBUS_BLOCK_READ_MIN_LEN;
} else {
/*
* When Rx msg len less than Rx fifo capacity
* Receive fifo depth should set to Rx msg len minus 2
*/
rfd_set = rxmsg_len - 2;
i2c->rx_msg->len = rxmsg_len + 1;
}
xiic_setreg8(i2c, XIIC_RFD_REG_OFFSET, rfd_set);
return;
}
/* Invalid message length, trigger STATE_ERROR with tx_msg_len in ISR */
i2c->tx_msg->len = 3;
i2c->smbus_block_read = false;
dev_err(i2c->adap.dev.parent, "smbus_block_read Invalid msg length\n");
}
static void xiic_read_rx(struct xiic_i2c *i2c)
{
u8 bytes_in_fifo, cr = 0, bytes_to_read = 0;
u32 bytes_rem = 0;
int i;
bytes_in_fifo = xiic_getreg8(i2c, XIIC_RFO_REG_OFFSET) + 1;
dev_dbg(i2c->adap.dev.parent,
"%s entry, bytes in fifo: %d, rem: %d, SR: 0x%x, CR: 0x%x\n",
__func__, bytes_in_fifo, xiic_rx_space(i2c),
xiic_getreg8(i2c, XIIC_SR_REG_OFFSET),
xiic_getreg8(i2c, XIIC_CR_REG_OFFSET));
if (bytes_in_fifo > xiic_rx_space(i2c))
bytes_in_fifo = xiic_rx_space(i2c);
bytes_to_read = bytes_in_fifo;
if (!i2c->dynamic) {
bytes_rem = xiic_rx_space(i2c) - bytes_in_fifo;
/* Set msg length if smbus_block_read */
if (i2c->rx_msg->flags & I2C_M_RECV_LEN) {
xiic_smbus_block_read_setup(i2c);
return;
}
if (bytes_rem > IIC_RX_FIFO_DEPTH) {
bytes_to_read = bytes_in_fifo;
} else if (bytes_rem > 1) {
bytes_to_read = bytes_rem - 1;
} else if (bytes_rem == 1) {
bytes_to_read = 1;
/* Set NACK in CR to indicate slave transmitter */
cr = xiic_getreg8(i2c, XIIC_CR_REG_OFFSET);
xiic_setreg8(i2c, XIIC_CR_REG_OFFSET, cr |
XIIC_CR_NO_ACK_MASK);
} else if (bytes_rem == 0) {
bytes_to_read = bytes_in_fifo;
/* Generate stop on the bus if it is last message */
if (i2c->nmsgs == 1) {
cr = xiic_getreg8(i2c, XIIC_CR_REG_OFFSET);
xiic_setreg8(i2c, XIIC_CR_REG_OFFSET, cr &
~XIIC_CR_MSMS_MASK);
}
/* Make TXACK=0, clean up for next transaction */
cr = xiic_getreg8(i2c, XIIC_CR_REG_OFFSET);
xiic_setreg8(i2c, XIIC_CR_REG_OFFSET, cr &
~XIIC_CR_NO_ACK_MASK);
}
}
/* Read the fifo */
for (i = 0; i < bytes_to_read; i++) {
i2c->rx_msg->buf[i2c->rx_pos++] =
xiic_getreg8(i2c, XIIC_DRR_REG_OFFSET);
}
if (i2c->dynamic) {
u8 bytes;
/* Receive remaining bytes if less than fifo depth */
bytes = min_t(u8, xiic_rx_space(i2c), IIC_RX_FIFO_DEPTH);
bytes--;
xiic_setreg8(i2c, XIIC_RFD_REG_OFFSET, bytes);
}
}
static int xiic_tx_fifo_space(struct xiic_i2c *i2c)
{
/* return the actual space left in the FIFO */
return IIC_TX_FIFO_DEPTH - xiic_getreg8(i2c, XIIC_TFO_REG_OFFSET) - 1;
}
static void xiic_fill_tx_fifo(struct xiic_i2c *i2c)
{
u8 fifo_space = xiic_tx_fifo_space(i2c);
int len = xiic_tx_space(i2c);
len = (len > fifo_space) ? fifo_space : len;
dev_dbg(i2c->adap.dev.parent, "%s entry, len: %d, fifo space: %d\n",
__func__, len, fifo_space);
while (len--) {
u16 data = i2c->tx_msg->buf[i2c->tx_pos++];
if (!xiic_tx_space(i2c) && i2c->nmsgs == 1) {
/* last message in transfer -> STOP */
if (i2c->dynamic) {
data |= XIIC_TX_DYN_STOP_MASK;
} else {
u8 cr;
int status;
/* Wait till FIFO is empty so STOP is sent last */
status = xiic_wait_tx_empty(i2c);
if (status)
return;
/* Write to CR to stop */
cr = xiic_getreg8(i2c, XIIC_CR_REG_OFFSET);
xiic_setreg8(i2c, XIIC_CR_REG_OFFSET, cr &
~XIIC_CR_MSMS_MASK);
}
dev_dbg(i2c->adap.dev.parent, "%s TX STOP\n", __func__);
}
xiic_setreg16(i2c, XIIC_DTR_REG_OFFSET, data);
}
}
static void xiic_wakeup(struct xiic_i2c *i2c, enum xilinx_i2c_state code)
{
i2c->tx_msg = NULL;
i2c->rx_msg = NULL;
i2c->nmsgs = 0;
i2c->state = code;
complete(&i2c->completion);
}
static irqreturn_t xiic_process(int irq, void *dev_id)
{
struct xiic_i2c *i2c = dev_id;
u32 pend, isr, ier;
u32 clr = 0;
int xfer_more = 0;
int wakeup_req = 0;
enum xilinx_i2c_state wakeup_code = STATE_DONE;
int ret;
/* Get the interrupt Status from the IPIF. There is no clearing of
* interrupts in the IPIF. Interrupts must be cleared at the source.
* To find which interrupts are pending; AND interrupts pending with
* interrupts masked.
*/
mutex_lock(&i2c->lock);
isr = xiic_getreg32(i2c, XIIC_IISR_OFFSET);
ier = xiic_getreg32(i2c, XIIC_IIER_OFFSET);
pend = isr & ier;
dev_dbg(i2c->adap.dev.parent, "%s: IER: 0x%x, ISR: 0x%x, pend: 0x%x\n",
__func__, ier, isr, pend);
dev_dbg(i2c->adap.dev.parent, "%s: SR: 0x%x, msg: %p, nmsgs: %d\n",
__func__, xiic_getreg8(i2c, XIIC_SR_REG_OFFSET),
i2c->tx_msg, i2c->nmsgs);
dev_dbg(i2c->adap.dev.parent, "%s, ISR: 0x%x, CR: 0x%x\n",
__func__, xiic_getreg32(i2c, XIIC_IISR_OFFSET),
xiic_getreg8(i2c, XIIC_CR_REG_OFFSET));
/* Service requesting interrupt */
if ((pend & XIIC_INTR_ARB_LOST_MASK) ||
((pend & XIIC_INTR_TX_ERROR_MASK) &&
!(pend & XIIC_INTR_RX_FULL_MASK))) {
/* bus arbritration lost, or...
* Transmit error _OR_ RX completed
* if this happens when RX_FULL is not set
* this is probably a TX error
*/
dev_dbg(i2c->adap.dev.parent, "%s error\n", __func__);
/* dynamic mode seem to suffer from problems if we just flushes
* fifos and the next message is a TX with len 0 (only addr)
* reset the IP instead of just flush fifos
*/
ret = xiic_reinit(i2c);
if (!ret)
dev_dbg(i2c->adap.dev.parent, "reinit failed\n");
if (i2c->rx_msg) {
wakeup_req = 1;
wakeup_code = STATE_ERROR;
}
if (i2c->tx_msg) {
wakeup_req = 1;
wakeup_code = STATE_ERROR;
}
}
if (pend & XIIC_INTR_RX_FULL_MASK) {
/* Receive register/FIFO is full */
clr |= XIIC_INTR_RX_FULL_MASK;
if (!i2c->rx_msg) {
dev_dbg(i2c->adap.dev.parent,
"%s unexpected RX IRQ\n", __func__);
xiic_clear_rx_fifo(i2c);
goto out;
}
xiic_read_rx(i2c);
if (xiic_rx_space(i2c) == 0) {
/* this is the last part of the message */
i2c->rx_msg = NULL;
/* also clear TX error if there (RX complete) */
clr |= (isr & XIIC_INTR_TX_ERROR_MASK);
dev_dbg(i2c->adap.dev.parent,
"%s end of message, nmsgs: %d\n",
__func__, i2c->nmsgs);
/* send next message if this wasn't the last,
* otherwise the transfer will be finialise when
* receiving the bus not busy interrupt
*/
if (i2c->nmsgs > 1) {
i2c->nmsgs--;
i2c->tx_msg++;
dev_dbg(i2c->adap.dev.parent,
"%s will start next...\n", __func__);
xfer_more = 1;
}
}
}
if (pend & (XIIC_INTR_TX_EMPTY_MASK | XIIC_INTR_TX_HALF_MASK)) {
/* Transmit register/FIFO is empty or ½ empty */
clr |= (pend &
(XIIC_INTR_TX_EMPTY_MASK | XIIC_INTR_TX_HALF_MASK));
if (!i2c->tx_msg) {
dev_dbg(i2c->adap.dev.parent,
"%s unexpected TX IRQ\n", __func__);
goto out;
}
xiic_fill_tx_fifo(i2c);
/* current message sent and there is space in the fifo */
if (!xiic_tx_space(i2c) && xiic_tx_fifo_space(i2c) >= 2) {
dev_dbg(i2c->adap.dev.parent,
"%s end of message sent, nmsgs: %d\n",
__func__, i2c->nmsgs);
if (i2c->nmsgs > 1) {
i2c->nmsgs--;
i2c->tx_msg++;
xfer_more = 1;
} else {
xiic_irq_dis(i2c, XIIC_INTR_TX_HALF_MASK);
dev_dbg(i2c->adap.dev.parent,
"%s Got TX IRQ but no more to do...\n",
__func__);
}
} else if (!xiic_tx_space(i2c) && (i2c->nmsgs == 1))
/* current frame is sent and is last,
* make sure to disable tx half
*/
xiic_irq_dis(i2c, XIIC_INTR_TX_HALF_MASK);
}
if (pend & XIIC_INTR_BNB_MASK) {
/* IIC bus has transitioned to not busy */
clr |= XIIC_INTR_BNB_MASK;
/* The bus is not busy, disable BusNotBusy interrupt */
xiic_irq_dis(i2c, XIIC_INTR_BNB_MASK);
if (i2c->tx_msg && i2c->smbus_block_read) {
i2c->smbus_block_read = false;
/* Set requested message len=1 to indicate STATE_DONE */
i2c->tx_msg->len = 1;
}
if (!i2c->tx_msg)
goto out;
wakeup_req = 1;
if (i2c->nmsgs == 1 && !i2c->rx_msg &&
xiic_tx_space(i2c) == 0)
wakeup_code = STATE_DONE;
else
wakeup_code = STATE_ERROR;
}
out:
dev_dbg(i2c->adap.dev.parent, "%s clr: 0x%x\n", __func__, clr);
xiic_setreg32(i2c, XIIC_IISR_OFFSET, clr);
if (xfer_more)
__xiic_start_xfer(i2c);
if (wakeup_req)
xiic_wakeup(i2c, wakeup_code);
WARN_ON(xfer_more && wakeup_req);
mutex_unlock(&i2c->lock);
return IRQ_HANDLED;
}
static int xiic_bus_busy(struct xiic_i2c *i2c)
{
u8 sr = xiic_getreg8(i2c, XIIC_SR_REG_OFFSET);
return (sr & XIIC_SR_BUS_BUSY_MASK) ? -EBUSY : 0;
}
static int xiic_busy(struct xiic_i2c *i2c)
{
int tries = 3;
int err;
if (i2c->tx_msg || i2c->rx_msg)
return -EBUSY;
/* In single master mode bus can only be busy, when in use by this
* driver. If the register indicates bus being busy for some reason we
* should ignore it, since bus will never be released and i2c will be
* stuck forever.
*/
if (i2c->singlemaster) {
return 0;
}
/* for instance if previous transfer was terminated due to TX error
* it might be that the bus is on it's way to become available
* give it at most 3 ms to wake
*/
err = xiic_bus_busy(i2c);
while (err && tries--) {
msleep(1);
err = xiic_bus_busy(i2c);
}
return err;
}
static void xiic_start_recv(struct xiic_i2c *i2c)
{
u16 rx_watermark;
u8 cr = 0, rfd_set = 0;
struct i2c_msg *msg = i2c->rx_msg = i2c->tx_msg;
dev_dbg(i2c->adap.dev.parent, "%s entry, ISR: 0x%x, CR: 0x%x\n",
__func__, xiic_getreg32(i2c, XIIC_IISR_OFFSET),
xiic_getreg8(i2c, XIIC_CR_REG_OFFSET));
/* Disable Tx interrupts */
xiic_irq_dis(i2c, XIIC_INTR_TX_HALF_MASK | XIIC_INTR_TX_EMPTY_MASK);
if (i2c->dynamic) {
u8 bytes;
u16 val;
/* Clear and enable Rx full interrupt. */
xiic_irq_clr_en(i2c, XIIC_INTR_RX_FULL_MASK |
XIIC_INTR_TX_ERROR_MASK);
/*
* We want to get all but last byte, because the TX_ERROR IRQ
* is used to indicate error ACK on the address, and
* negative ack on the last received byte, so to not mix
* them receive all but last.
* In the case where there is only one byte to receive
* we can check if ERROR and RX full is set at the same time
*/
rx_watermark = msg->len;
bytes = min_t(u8, rx_watermark, IIC_RX_FIFO_DEPTH);
if (rx_watermark > 0)
bytes--;
xiic_setreg8(i2c, XIIC_RFD_REG_OFFSET, bytes);
/* write the address */
xiic_setreg16(i2c, XIIC_DTR_REG_OFFSET,
i2c_8bit_addr_from_msg(msg) |
XIIC_TX_DYN_START_MASK);
/* If last message, include dynamic stop bit with length */
val = (i2c->nmsgs == 1) ? XIIC_TX_DYN_STOP_MASK : 0;
val |= msg->len;
xiic_setreg16(i2c, XIIC_DTR_REG_OFFSET, val);
xiic_irq_clr_en(i2c, XIIC_INTR_BNB_MASK);
} else {
/*
* If previous message is Tx, make sure that Tx FIFO is empty
* before starting a new transfer as the repeated start in
* standard mode can corrupt the transaction if there are
* still bytes to be transmitted in FIFO
*/
if (i2c->prev_msg_tx) {
int status;
status = xiic_wait_tx_empty(i2c);
if (status)
return;
}
cr = xiic_getreg8(i2c, XIIC_CR_REG_OFFSET);
/* Set Receive fifo depth */
rx_watermark = msg->len;
if (rx_watermark > IIC_RX_FIFO_DEPTH) {
rfd_set = IIC_RX_FIFO_DEPTH - 1;
} else if (rx_watermark == 1) {
rfd_set = rx_watermark - 1;
/* Set No_ACK, except for smbus_block_read */
if (!(i2c->rx_msg->flags & I2C_M_RECV_LEN)) {
/* Handle single byte transfer separately */
cr |= XIIC_CR_NO_ACK_MASK;
}
} else if (rx_watermark == 0) {
rfd_set = rx_watermark;
} else {
rfd_set = rx_watermark - 2;
}
/* Check if RSTA should be set */
if (cr & XIIC_CR_MSMS_MASK) {
/* Already a master, RSTA should be set */
xiic_setreg8(i2c, XIIC_CR_REG_OFFSET, (cr |
XIIC_CR_REPEATED_START_MASK) &
~(XIIC_CR_DIR_IS_TX_MASK));
}
xiic_setreg8(i2c, XIIC_RFD_REG_OFFSET, rfd_set);
/* Clear and enable Rx full and transmit complete interrupts */
xiic_irq_clr_en(i2c, XIIC_INTR_RX_FULL_MASK |
XIIC_INTR_TX_ERROR_MASK);
/* Write the address */
xiic_setreg16(i2c, XIIC_DTR_REG_OFFSET,
i2c_8bit_addr_from_msg(msg));
/* Write to Control Register,to start transaction in Rx mode */
if ((cr & XIIC_CR_MSMS_MASK) == 0) {
xiic_setreg8(i2c, XIIC_CR_REG_OFFSET, (cr |
XIIC_CR_MSMS_MASK)
& ~(XIIC_CR_DIR_IS_TX_MASK));
}
dev_dbg(i2c->adap.dev.parent, "%s end, ISR: 0x%x, CR: 0x%x\n",
__func__, xiic_getreg32(i2c, XIIC_IISR_OFFSET),
xiic_getreg8(i2c, XIIC_CR_REG_OFFSET));
}
if (i2c->nmsgs == 1)
/* very last, enable bus not busy as well */
xiic_irq_clr_en(i2c, XIIC_INTR_BNB_MASK);
/* the message is tx:ed */
i2c->tx_pos = msg->len;
/* Enable interrupts */
xiic_setreg32(i2c, XIIC_DGIER_OFFSET, XIIC_GINTR_ENABLE_MASK);
i2c->prev_msg_tx = false;
}
static void xiic_start_send(struct xiic_i2c *i2c)
{
u8 cr = 0;
u16 data;
struct i2c_msg *msg = i2c->tx_msg;
dev_dbg(i2c->adap.dev.parent, "%s entry, msg: %p, len: %d",
__func__, msg, msg->len);
dev_dbg(i2c->adap.dev.parent, "%s entry, ISR: 0x%x, CR: 0x%x\n",
__func__, xiic_getreg32(i2c, XIIC_IISR_OFFSET),
xiic_getreg8(i2c, XIIC_CR_REG_OFFSET));
if (i2c->dynamic) {
/* write the address */
data = i2c_8bit_addr_from_msg(msg) |
XIIC_TX_DYN_START_MASK;
if (i2c->nmsgs == 1 && msg->len == 0)
/* no data and last message -> add STOP */
data |= XIIC_TX_DYN_STOP_MASK;
xiic_setreg16(i2c, XIIC_DTR_REG_OFFSET, data);
/* Clear any pending Tx empty, Tx Error and then enable them */
xiic_irq_clr_en(i2c, XIIC_INTR_TX_EMPTY_MASK |
XIIC_INTR_TX_ERROR_MASK |
XIIC_INTR_BNB_MASK |
((i2c->nmsgs > 1 || xiic_tx_space(i2c)) ?
XIIC_INTR_TX_HALF_MASK : 0));
xiic_fill_tx_fifo(i2c);
} else {
/*
* If previous message is Tx, make sure that Tx FIFO is empty
* before starting a new transfer as the repeated start in
* standard mode can corrupt the transaction if there are
* still bytes to be transmitted in FIFO
*/
if (i2c->prev_msg_tx) {
int status;
status = xiic_wait_tx_empty(i2c);
if (status)
return;
}
/* Check if RSTA should be set */
cr = xiic_getreg8(i2c, XIIC_CR_REG_OFFSET);
if (cr & XIIC_CR_MSMS_MASK) {
/* Already a master, RSTA should be set */
xiic_setreg8(i2c, XIIC_CR_REG_OFFSET, (cr |
XIIC_CR_REPEATED_START_MASK |
XIIC_CR_DIR_IS_TX_MASK) &
~(XIIC_CR_NO_ACK_MASK));
}
/* Write address to FIFO */
data = i2c_8bit_addr_from_msg(msg);
xiic_setreg16(i2c, XIIC_DTR_REG_OFFSET, data);
/* Fill fifo */
xiic_fill_tx_fifo(i2c);
if ((cr & XIIC_CR_MSMS_MASK) == 0) {
/* Start Tx by writing to CR */
cr = xiic_getreg8(i2c, XIIC_CR_REG_OFFSET);
xiic_setreg8(i2c, XIIC_CR_REG_OFFSET, cr |
XIIC_CR_MSMS_MASK |
XIIC_CR_DIR_IS_TX_MASK);
}
/* Clear any pending Tx empty, Tx Error and then enable them */
xiic_irq_clr_en(i2c, XIIC_INTR_TX_EMPTY_MASK |
XIIC_INTR_TX_ERROR_MASK |
XIIC_INTR_BNB_MASK);
}
i2c->prev_msg_tx = true;
}
static void __xiic_start_xfer(struct xiic_i2c *i2c)
{
int fifo_space = xiic_tx_fifo_space(i2c);
dev_dbg(i2c->adap.dev.parent, "%s entry, msg: %p, fifos space: %d\n",
__func__, i2c->tx_msg, fifo_space);
if (!i2c->tx_msg)
return;
i2c->rx_pos = 0;
i2c->tx_pos = 0;
i2c->state = STATE_START;
if (i2c->tx_msg->flags & I2C_M_RD) {
/* we dont date putting several reads in the FIFO */
xiic_start_recv(i2c);
} else {
xiic_start_send(i2c);
}
}
static int xiic_start_xfer(struct xiic_i2c *i2c, struct i2c_msg *msgs, int num)
{
bool broken_read, max_read_len, smbus_blk_read;
int ret, count;
mutex_lock(&i2c->lock);
ret = xiic_busy(i2c);
if (ret)
goto out;
i2c->tx_msg = msgs;
i2c->rx_msg = NULL;
i2c->nmsgs = num;
init_completion(&i2c->completion);
/* Decide standard mode or Dynamic mode */
i2c->dynamic = true;
/* Initialize prev message type */
i2c->prev_msg_tx = false;
/*
* Scan through nmsgs, use dynamic mode when none of the below three
* conditions occur. We need standard mode even if one condition holds
* true in the entire array of messages in a single transfer.
* If read transaction as dynamic mode is broken for delayed reads
* in xlnx,axi-iic-2.0 / xlnx,xps-iic-2.00.a IP versions.
* If read length is > 255 bytes.
* If smbus_block_read transaction.
*/
for (count = 0; count < i2c->nmsgs; count++) {
broken_read = (i2c->quirks & DYNAMIC_MODE_READ_BROKEN_BIT) &&
(i2c->tx_msg[count].flags & I2C_M_RD);
max_read_len = (i2c->tx_msg[count].flags & I2C_M_RD) &&
(i2c->tx_msg[count].len > MAX_READ_LENGTH_DYNAMIC);
smbus_blk_read = (i2c->tx_msg[count].flags & I2C_M_RECV_LEN);
if (broken_read || max_read_len || smbus_blk_read) {
i2c->dynamic = false;
break;
}
}
ret = xiic_reinit(i2c);
if (!ret)
__xiic_start_xfer(i2c);
out:
mutex_unlock(&i2c->lock);
return ret;
}
static int xiic_xfer(struct i2c_adapter *adap, struct i2c_msg *msgs, int num)
{
struct xiic_i2c *i2c = i2c_get_adapdata(adap);
int err;
dev_dbg(adap->dev.parent, "%s entry SR: 0x%x\n", __func__,
xiic_getreg8(i2c, XIIC_SR_REG_OFFSET));
err = pm_runtime_resume_and_get(i2c->dev);
if (err < 0)
return err;
err = xiic_start_xfer(i2c, msgs, num);
if (err < 0) {
dev_err(adap->dev.parent, "Error xiic_start_xfer\n");
goto out;
}
err = wait_for_completion_timeout(&i2c->completion, XIIC_XFER_TIMEOUT);
mutex_lock(&i2c->lock);
if (err == 0) { /* Timeout */
i2c->tx_msg = NULL;
i2c->rx_msg = NULL;
i2c->nmsgs = 0;
err = -ETIMEDOUT;
} else {
err = (i2c->state == STATE_DONE) ? num : -EIO;
}
mutex_unlock(&i2c->lock);
out:
pm_runtime_mark_last_busy(i2c->dev);
pm_runtime_put_autosuspend(i2c->dev);
return err;
}
static u32 xiic_func(struct i2c_adapter *adap)
{
return I2C_FUNC_I2C | I2C_FUNC_SMBUS_EMUL | I2C_FUNC_SMBUS_BLOCK_DATA;
}
static const struct i2c_algorithm xiic_algorithm = {
.master_xfer = xiic_xfer,
.functionality = xiic_func,
};
static const struct i2c_adapter xiic_adapter = {
.owner = THIS_MODULE,
.class = I2C_CLASS_DEPRECATED,
.algo = &xiic_algorithm,
};
static const struct xiic_version_data xiic_2_00 = {
.quirks = DYNAMIC_MODE_READ_BROKEN_BIT,
};
#if defined(CONFIG_OF)
static const struct of_device_id xiic_of_match[] = {
{ .compatible = "xlnx,xps-iic-2.00.a", .data = &xiic_2_00 },
{ .compatible = "xlnx,axi-iic-2.1", },
{},
};
MODULE_DEVICE_TABLE(of, xiic_of_match);
#endif
static int xiic_i2c_probe(struct platform_device *pdev)
{
struct xiic_i2c *i2c;
struct xiic_i2c_platform_data *pdata;
const struct of_device_id *match;
struct resource *res;
int ret, irq;
u8 i;
u32 sr;
i2c = devm_kzalloc(&pdev->dev, sizeof(*i2c), GFP_KERNEL);
if (!i2c)
return -ENOMEM;
match = of_match_node(xiic_of_match, pdev->dev.of_node);
if (match && match->data) {
const struct xiic_version_data *data = match->data;
i2c->quirks = data->quirks;
}
res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
i2c->base = devm_ioremap_resource(&pdev->dev, res);
if (IS_ERR(i2c->base))
return PTR_ERR(i2c->base);
irq = platform_get_irq(pdev, 0);
if (irq < 0)
return irq;
pdata = dev_get_platdata(&pdev->dev);
/* hook up driver to tree */
platform_set_drvdata(pdev, i2c);
i2c->adap = xiic_adapter;
i2c_set_adapdata(&i2c->adap, i2c);
i2c->adap.dev.parent = &pdev->dev;
i2c->adap.dev.of_node = pdev->dev.of_node;
snprintf(i2c->adap.name, sizeof(i2c->adap.name),
DRIVER_NAME " %s", pdev->name);
mutex_init(&i2c->lock);
i2c->clk = devm_clk_get(&pdev->dev, NULL);
if (IS_ERR(i2c->clk))
return dev_err_probe(&pdev->dev, PTR_ERR(i2c->clk),
"input clock not found.\n");
ret = clk_prepare_enable(i2c->clk);
if (ret) {
dev_err(&pdev->dev, "Unable to enable clock.\n");
return ret;
}
i2c->dev = &pdev->dev;
pm_runtime_set_autosuspend_delay(i2c->dev, XIIC_PM_TIMEOUT);
pm_runtime_use_autosuspend(i2c->dev);
pm_runtime_set_active(i2c->dev);
pm_runtime_enable(i2c->dev);
/* SCL frequency configuration */
i2c->input_clk = clk_get_rate(i2c->clk);
ret = of_property_read_u32(pdev->dev.of_node, "clock-frequency",
&i2c->i2c_clk);
/* If clock-frequency not specified in DT, do not configure in SW */
if (ret || i2c->i2c_clk > I2C_MAX_FAST_MODE_PLUS_FREQ)
i2c->i2c_clk = 0;
ret = devm_request_threaded_irq(&pdev->dev, irq, NULL,
xiic_process, IRQF_ONESHOT,
pdev->name, i2c);
if (ret < 0) {
dev_err(&pdev->dev, "Cannot claim IRQ\n");
goto err_clk_dis;
}
i2c->singlemaster =
of_property_read_bool(pdev->dev.of_node, "single-master");
/*
* Detect endianness
* Try to reset the TX FIFO. Then check the EMPTY flag. If it is not
* set, assume that the endianness was wrong and swap.
*/
i2c->endianness = LITTLE;
xiic_setreg32(i2c, XIIC_CR_REG_OFFSET, XIIC_CR_TX_FIFO_RESET_MASK);
/* Reset is cleared in xiic_reinit */
sr = xiic_getreg32(i2c, XIIC_SR_REG_OFFSET);
if (!(sr & XIIC_SR_TX_FIFO_EMPTY_MASK))
i2c->endianness = BIG;
ret = xiic_reinit(i2c);
if (ret < 0) {
dev_err(&pdev->dev, "Cannot xiic_reinit\n");
goto err_clk_dis;
}
/* add i2c adapter to i2c tree */
ret = i2c_add_adapter(&i2c->adap);
if (ret) {
xiic_deinit(i2c);
goto err_clk_dis;
}
if (pdata) {
/* add in known devices to the bus */
for (i = 0; i < pdata->num_devices; i++)
i2c_new_client_device(&i2c->adap, pdata->devices + i);
}
dev_dbg(&pdev->dev, "mmio %08lx irq %d scl clock frequency %d\n",
(unsigned long)res->start, irq, i2c->i2c_clk);
return 0;
err_clk_dis:
pm_runtime_set_suspended(&pdev->dev);
pm_runtime_disable(&pdev->dev);
clk_disable_unprepare(i2c->clk);
return ret;
}
static int xiic_i2c_remove(struct platform_device *pdev)
{
struct xiic_i2c *i2c = platform_get_drvdata(pdev);
int ret;
/* remove adapter & data */
i2c_del_adapter(&i2c->adap);
ret = pm_runtime_get_sync(i2c->dev);
if (ret < 0)
dev_warn(&pdev->dev, "Failed to activate device for removal (%pe)\n",
ERR_PTR(ret));
else
xiic_deinit(i2c);
pm_runtime_put_sync(i2c->dev);
clk_disable_unprepare(i2c->clk);
pm_runtime_disable(&pdev->dev);
pm_runtime_set_suspended(&pdev->dev);
pm_runtime_dont_use_autosuspend(&pdev->dev);
return 0;
}
static int __maybe_unused xiic_i2c_runtime_suspend(struct device *dev)
{
struct xiic_i2c *i2c = dev_get_drvdata(dev);
clk_disable(i2c->clk);
return 0;
}
static int __maybe_unused xiic_i2c_runtime_resume(struct device *dev)
{
struct xiic_i2c *i2c = dev_get_drvdata(dev);
int ret;
ret = clk_enable(i2c->clk);
if (ret) {
dev_err(dev, "Cannot enable clock.\n");
return ret;
}
return 0;
}
static const struct dev_pm_ops xiic_dev_pm_ops = {
SET_RUNTIME_PM_OPS(xiic_i2c_runtime_suspend,
xiic_i2c_runtime_resume, NULL)
};
static struct platform_driver xiic_i2c_driver = {
.probe = xiic_i2c_probe,
.remove = xiic_i2c_remove,
.driver = {
.name = DRIVER_NAME,
.of_match_table = of_match_ptr(xiic_of_match),
.pm = &xiic_dev_pm_ops,
},
};
module_platform_driver(xiic_i2c_driver);
MODULE_ALIAS("platform:" DRIVER_NAME);
MODULE_AUTHOR("info@mocean-labs.com");
MODULE_DESCRIPTION("Xilinx I2C bus driver");
MODULE_LICENSE("GPL v2");
Reference in New Issue View Git Blame Copy Permalink