443 lines
13 KiB
C
443 lines
13 KiB
C
// SPDX-License-Identifier: GPL-2.0
|
|
/* Copyright (c) 2018, Broadcom */
|
|
|
|
/*
|
|
* This module contains USB PHY initialization for power up and S3 resume
|
|
* for newer Synopsys based USB hardware first used on the bcm7216.
|
|
*/
|
|
|
|
#include <linux/delay.h>
|
|
#include <linux/io.h>
|
|
|
|
#include <linux/soc/brcmstb/brcmstb.h>
|
|
#include "phy-brcm-usb-init.h"
|
|
|
|
#define PHY_LOCK_TIMEOUT_MS 200
|
|
|
|
/* Register definitions for syscon piarbctl registers */
|
|
#define PIARBCTL_CAM 0x00
|
|
#define PIARBCTL_SPLITTER 0x04
|
|
#define PIARBCTL_MISC 0x08
|
|
#define PIARBCTL_MISC_SATA_PRIORITY_MASK GENMASK(3, 0)
|
|
#define PIARBCTL_MISC_CAM0_MEM_PAGE_MASK GENMASK(7, 4)
|
|
#define PIARBCTL_MISC_CAM1_MEM_PAGE_MASK GENMASK(11, 8)
|
|
#define PIARBCTL_MISC_USB_MEM_PAGE_MASK GENMASK(15, 12)
|
|
#define PIARBCTL_MISC_USB_PRIORITY_MASK GENMASK(19, 16)
|
|
#define PIARBCTL_MISC_USB_4G_SDRAM_MASK BIT(29)
|
|
#define PIARBCTL_MISC_USB_SELECT_MASK BIT(30)
|
|
#define PIARBCTL_MISC_SECURE_MASK BIT(31)
|
|
|
|
#define PIARBCTL_MISC_USB_ONLY_MASK \
|
|
(PIARBCTL_MISC_USB_SELECT_MASK | \
|
|
PIARBCTL_MISC_USB_4G_SDRAM_MASK | \
|
|
PIARBCTL_MISC_USB_PRIORITY_MASK | \
|
|
PIARBCTL_MISC_USB_MEM_PAGE_MASK)
|
|
|
|
/* Register definitions for the USB CTRL block */
|
|
#define USB_CTRL_SETUP 0x00
|
|
#define USB_CTRL_SETUP_IOC_MASK BIT(4)
|
|
#define USB_CTRL_SETUP_IPP_MASK BIT(5)
|
|
#define USB_CTRL_SETUP_SOFT_SHUTDOWN_MASK BIT(9)
|
|
#define USB_CTRL_SETUP_SCB1_EN_MASK BIT(14)
|
|
#define USB_CTRL_SETUP_SCB2_EN_MASK BIT(15)
|
|
#define USB_CTRL_SETUP_tca_drv_sel_MASK BIT(24)
|
|
#define USB_CTRL_SETUP_STRAP_IPP_SEL_MASK BIT(25)
|
|
#define USB_CTRL_USB_PM 0x04
|
|
#define USB_CTRL_USB_PM_XHC_S2_CLK_SWITCH_EN_MASK BIT(3)
|
|
#define USB_CTRL_USB_PM_XHC_PME_EN_MASK BIT(4)
|
|
#define USB_CTRL_USB_PM_XHC_SOFT_RESETB_MASK BIT(22)
|
|
#define USB_CTRL_USB_PM_BDC_SOFT_RESETB_MASK BIT(23)
|
|
#define USB_CTRL_USB_PM_SOFT_RESET_MASK BIT(30)
|
|
#define USB_CTRL_USB_PM_USB_PWRDN_MASK BIT(31)
|
|
#define USB_CTRL_USB_PM_STATUS 0x08
|
|
#define USB_CTRL_USB_DEVICE_CTL1 0x10
|
|
#define USB_CTRL_USB_DEVICE_CTL1_PORT_MODE_MASK GENMASK(1, 0)
|
|
#define USB_CTRL_TEST_PORT_CTL 0x30
|
|
#define USB_CTRL_TEST_PORT_CTL_TPOUT_SEL_MASK GENMASK(7, 0)
|
|
#define USB_CTRL_TEST_PORT_CTL_TPOUT_SEL_PME_GEN_MASK 0x0000002e
|
|
#define USB_CTRL_TP_DIAG1 0x34
|
|
#define USB_CTLR_TP_DIAG1_wake_MASK BIT(1)
|
|
#define USB_CTRL_CTLR_CSHCR 0x50
|
|
#define USB_CTRL_CTLR_CSHCR_ctl_pme_en_MASK BIT(18)
|
|
|
|
/* Register definitions for the USB_PHY block in 7211b0 */
|
|
#define USB_PHY_PLL_CTL 0x00
|
|
#define USB_PHY_PLL_CTL_PLL_SUSPEND_MASK BIT(27)
|
|
#define USB_PHY_PLL_CTL_PLL_RESETB_MASK BIT(30)
|
|
#define USB_PHY_PLL_LDO_CTL 0x08
|
|
#define USB_PHY_PLL_LDO_CTL_AFE_BG_PWRDWNB_MASK BIT(0)
|
|
#define USB_PHY_PLL_LDO_CTL_AFE_LDO_PWRDWNB_MASK BIT(1)
|
|
#define USB_PHY_PLL_LDO_CTL_AFE_CORERDY_MASK BIT(2)
|
|
#define USB_PHY_UTMI_CTL_1 0x04
|
|
#define USB_PHY_UTMI_CTL_1_PHY_MODE_MASK GENMASK(3, 2)
|
|
#define USB_PHY_UTMI_CTL_1_PHY_MODE_SHIFT 2
|
|
#define USB_PHY_UTMI_CTL_1_POWER_UP_FSM_EN_MASK BIT(11)
|
|
#define USB_PHY_IDDQ 0x1c
|
|
#define USB_PHY_IDDQ_phy_iddq_MASK BIT(0)
|
|
#define USB_PHY_STATUS 0x20
|
|
#define USB_PHY_STATUS_pll_lock_MASK BIT(0)
|
|
|
|
/* Register definitions for the MDIO registers in the DWC2 block of
|
|
* the 7211b0.
|
|
* NOTE: The PHY's MDIO registers are only accessible through the
|
|
* legacy DesignWare USB controller even though it's not being used.
|
|
*/
|
|
#define USB_GMDIOCSR 0
|
|
#define USB_GMDIOGEN 4
|
|
|
|
/* Register definitions for the BDC EC block in 7211b0 */
|
|
#define BDC_EC_AXIRDA 0x0c
|
|
#define BDC_EC_AXIRDA_RTS_MASK GENMASK(31, 28)
|
|
#define BDC_EC_AXIRDA_RTS_SHIFT 28
|
|
|
|
|
|
static void usb_mdio_write_7211b0(struct brcm_usb_init_params *params,
|
|
uint8_t addr, uint16_t data)
|
|
{
|
|
void __iomem *usb_mdio = params->regs[BRCM_REGS_USB_MDIO];
|
|
|
|
addr &= 0x1f; /* 5-bit address */
|
|
brcm_usb_writel(0xffffffff, usb_mdio + USB_GMDIOGEN);
|
|
while (brcm_usb_readl(usb_mdio + USB_GMDIOCSR) & (1<<31))
|
|
;
|
|
brcm_usb_writel(0x59020000 | (addr << 18) | data,
|
|
usb_mdio + USB_GMDIOGEN);
|
|
while (brcm_usb_readl(usb_mdio + USB_GMDIOCSR) & (1<<31))
|
|
;
|
|
brcm_usb_writel(0x00000000, usb_mdio + USB_GMDIOGEN);
|
|
while (brcm_usb_readl(usb_mdio + USB_GMDIOCSR) & (1<<31))
|
|
;
|
|
}
|
|
|
|
static uint16_t __maybe_unused usb_mdio_read_7211b0(
|
|
struct brcm_usb_init_params *params, uint8_t addr)
|
|
{
|
|
void __iomem *usb_mdio = params->regs[BRCM_REGS_USB_MDIO];
|
|
|
|
addr &= 0x1f; /* 5-bit address */
|
|
brcm_usb_writel(0xffffffff, usb_mdio + USB_GMDIOGEN);
|
|
while (brcm_usb_readl(usb_mdio + USB_GMDIOCSR) & (1<<31))
|
|
;
|
|
brcm_usb_writel(0x69020000 | (addr << 18), usb_mdio + USB_GMDIOGEN);
|
|
while (brcm_usb_readl(usb_mdio + USB_GMDIOCSR) & (1<<31))
|
|
;
|
|
brcm_usb_writel(0x00000000, usb_mdio + USB_GMDIOGEN);
|
|
while (brcm_usb_readl(usb_mdio + USB_GMDIOCSR) & (1<<31))
|
|
;
|
|
return brcm_usb_readl(usb_mdio + USB_GMDIOCSR) & 0xffff;
|
|
}
|
|
|
|
static void usb2_eye_fix_7211b0(struct brcm_usb_init_params *params)
|
|
{
|
|
/* select bank */
|
|
usb_mdio_write_7211b0(params, 0x1f, 0x80a0);
|
|
|
|
/* Set the eye */
|
|
usb_mdio_write_7211b0(params, 0x0a, 0xc6a0);
|
|
}
|
|
|
|
static void xhci_soft_reset(struct brcm_usb_init_params *params,
|
|
int on_off)
|
|
{
|
|
void __iomem *ctrl = params->regs[BRCM_REGS_CTRL];
|
|
|
|
/* Assert reset */
|
|
if (on_off)
|
|
USB_CTRL_UNSET(ctrl, USB_PM, XHC_SOFT_RESETB);
|
|
/* De-assert reset */
|
|
else
|
|
USB_CTRL_SET(ctrl, USB_PM, XHC_SOFT_RESETB);
|
|
}
|
|
|
|
static void usb_init_ipp(struct brcm_usb_init_params *params)
|
|
{
|
|
void __iomem *ctrl = params->regs[BRCM_REGS_CTRL];
|
|
u32 reg;
|
|
u32 orig_reg;
|
|
|
|
pr_debug("%s\n", __func__);
|
|
|
|
orig_reg = reg = brcm_usb_readl(USB_CTRL_REG(ctrl, SETUP));
|
|
if (params->ipp != 2)
|
|
/* override ipp strap pin (if it exits) */
|
|
reg &= ~(USB_CTRL_MASK(SETUP, STRAP_IPP_SEL));
|
|
|
|
/* Override the default OC and PP polarity */
|
|
reg &= ~(USB_CTRL_MASK(SETUP, IPP) | USB_CTRL_MASK(SETUP, IOC));
|
|
if (params->ioc)
|
|
reg |= USB_CTRL_MASK(SETUP, IOC);
|
|
if (params->ipp == 1)
|
|
reg |= USB_CTRL_MASK(SETUP, IPP);
|
|
brcm_usb_writel(reg, USB_CTRL_REG(ctrl, SETUP));
|
|
|
|
/*
|
|
* If we're changing IPP, make sure power is off long enough
|
|
* to turn off any connected devices.
|
|
*/
|
|
if ((reg ^ orig_reg) & USB_CTRL_MASK(SETUP, IPP))
|
|
msleep(50);
|
|
}
|
|
|
|
static void syscon_piarbctl_init(struct regmap *rmap)
|
|
{
|
|
/* Switch from legacy USB OTG controller to new STB USB controller */
|
|
regmap_update_bits(rmap, PIARBCTL_MISC, PIARBCTL_MISC_USB_ONLY_MASK,
|
|
PIARBCTL_MISC_USB_SELECT_MASK |
|
|
PIARBCTL_MISC_USB_4G_SDRAM_MASK);
|
|
}
|
|
|
|
static void usb_init_common(struct brcm_usb_init_params *params)
|
|
{
|
|
u32 reg;
|
|
void __iomem *ctrl = params->regs[BRCM_REGS_CTRL];
|
|
|
|
pr_debug("%s\n", __func__);
|
|
|
|
if (USB_CTRL_MASK(USB_DEVICE_CTL1, PORT_MODE)) {
|
|
reg = brcm_usb_readl(USB_CTRL_REG(ctrl, USB_DEVICE_CTL1));
|
|
reg &= ~USB_CTRL_MASK(USB_DEVICE_CTL1, PORT_MODE);
|
|
reg |= params->port_mode;
|
|
brcm_usb_writel(reg, USB_CTRL_REG(ctrl, USB_DEVICE_CTL1));
|
|
}
|
|
switch (params->supported_port_modes) {
|
|
case USB_CTLR_MODE_HOST:
|
|
USB_CTRL_UNSET(ctrl, USB_PM, BDC_SOFT_RESETB);
|
|
break;
|
|
default:
|
|
USB_CTRL_UNSET(ctrl, USB_PM, BDC_SOFT_RESETB);
|
|
USB_CTRL_SET(ctrl, USB_PM, BDC_SOFT_RESETB);
|
|
break;
|
|
}
|
|
}
|
|
|
|
static void usb_wake_enable_7211b0(struct brcm_usb_init_params *params,
|
|
bool enable)
|
|
{
|
|
void __iomem *ctrl = params->regs[BRCM_REGS_CTRL];
|
|
|
|
if (enable)
|
|
USB_CTRL_SET(ctrl, CTLR_CSHCR, ctl_pme_en);
|
|
else
|
|
USB_CTRL_UNSET(ctrl, CTLR_CSHCR, ctl_pme_en);
|
|
}
|
|
|
|
static void usb_wake_enable_7216(struct brcm_usb_init_params *params,
|
|
bool enable)
|
|
{
|
|
void __iomem *ctrl = params->regs[BRCM_REGS_CTRL];
|
|
|
|
if (enable)
|
|
USB_CTRL_SET(ctrl, USB_PM, XHC_PME_EN);
|
|
else
|
|
USB_CTRL_UNSET(ctrl, USB_PM, XHC_PME_EN);
|
|
}
|
|
|
|
static void usb_init_common_7211b0(struct brcm_usb_init_params *params)
|
|
{
|
|
void __iomem *ctrl = params->regs[BRCM_REGS_CTRL];
|
|
void __iomem *usb_phy = params->regs[BRCM_REGS_USB_PHY];
|
|
void __iomem *bdc_ec = params->regs[BRCM_REGS_BDC_EC];
|
|
int timeout_ms = PHY_LOCK_TIMEOUT_MS;
|
|
u32 reg;
|
|
|
|
if (params->syscon_piarbctl)
|
|
syscon_piarbctl_init(params->syscon_piarbctl);
|
|
|
|
USB_CTRL_UNSET(ctrl, USB_PM, USB_PWRDN);
|
|
|
|
usb_wake_enable_7211b0(params, false);
|
|
if (!params->wake_enabled) {
|
|
|
|
/* undo possible suspend settings */
|
|
brcm_usb_writel(0, usb_phy + USB_PHY_IDDQ);
|
|
reg = brcm_usb_readl(usb_phy + USB_PHY_PLL_CTL);
|
|
reg |= USB_PHY_PLL_CTL_PLL_RESETB_MASK;
|
|
brcm_usb_writel(reg, usb_phy + USB_PHY_PLL_CTL);
|
|
|
|
/* temporarily enable FSM so PHY comes up properly */
|
|
reg = brcm_usb_readl(usb_phy + USB_PHY_UTMI_CTL_1);
|
|
reg |= USB_PHY_UTMI_CTL_1_POWER_UP_FSM_EN_MASK;
|
|
brcm_usb_writel(reg, usb_phy + USB_PHY_UTMI_CTL_1);
|
|
}
|
|
|
|
/* Disable PLL auto suspend */
|
|
reg = brcm_usb_readl(usb_phy + USB_PHY_PLL_CTL);
|
|
reg |= USB_PHY_PLL_CTL_PLL_SUSPEND_MASK;
|
|
brcm_usb_writel(reg, usb_phy + USB_PHY_PLL_CTL);
|
|
|
|
/* Init the PHY */
|
|
reg = USB_PHY_PLL_LDO_CTL_AFE_CORERDY_MASK |
|
|
USB_PHY_PLL_LDO_CTL_AFE_LDO_PWRDWNB_MASK |
|
|
USB_PHY_PLL_LDO_CTL_AFE_BG_PWRDWNB_MASK;
|
|
brcm_usb_writel(reg, usb_phy + USB_PHY_PLL_LDO_CTL);
|
|
|
|
/* wait for lock */
|
|
while (timeout_ms-- > 0) {
|
|
reg = brcm_usb_readl(usb_phy + USB_PHY_STATUS);
|
|
if (reg & USB_PHY_STATUS_pll_lock_MASK)
|
|
break;
|
|
usleep_range(1000, 2000);
|
|
}
|
|
|
|
/* Set the PHY_MODE */
|
|
reg = brcm_usb_readl(usb_phy + USB_PHY_UTMI_CTL_1);
|
|
reg &= ~USB_PHY_UTMI_CTL_1_PHY_MODE_MASK;
|
|
reg |= params->supported_port_modes << USB_PHY_UTMI_CTL_1_PHY_MODE_SHIFT;
|
|
brcm_usb_writel(reg, usb_phy + USB_PHY_UTMI_CTL_1);
|
|
|
|
usb_init_common(params);
|
|
|
|
/*
|
|
* The BDC controller will get occasional failures with
|
|
* the default "Read Transaction Size" of 6 (1024 bytes).
|
|
* Set it to 4 (256 bytes).
|
|
*/
|
|
if ((params->supported_port_modes != USB_CTLR_MODE_HOST) && bdc_ec) {
|
|
reg = brcm_usb_readl(bdc_ec + BDC_EC_AXIRDA);
|
|
reg &= ~BDC_EC_AXIRDA_RTS_MASK;
|
|
reg |= (0x4 << BDC_EC_AXIRDA_RTS_SHIFT);
|
|
brcm_usb_writel(reg, bdc_ec + BDC_EC_AXIRDA);
|
|
}
|
|
|
|
/*
|
|
* Disable FSM, otherwise the PHY will auto suspend when no
|
|
* device is connected and will be reset on resume.
|
|
*/
|
|
reg = brcm_usb_readl(usb_phy + USB_PHY_UTMI_CTL_1);
|
|
reg &= ~USB_PHY_UTMI_CTL_1_POWER_UP_FSM_EN_MASK;
|
|
brcm_usb_writel(reg, usb_phy + USB_PHY_UTMI_CTL_1);
|
|
|
|
usb2_eye_fix_7211b0(params);
|
|
}
|
|
|
|
static void usb_init_common_7216(struct brcm_usb_init_params *params)
|
|
{
|
|
void __iomem *ctrl = params->regs[BRCM_REGS_CTRL];
|
|
|
|
USB_CTRL_UNSET(ctrl, USB_PM, XHC_S2_CLK_SWITCH_EN);
|
|
USB_CTRL_UNSET(ctrl, USB_PM, USB_PWRDN);
|
|
|
|
/* 1 millisecond - for USB clocks to settle down */
|
|
usleep_range(1000, 2000);
|
|
|
|
usb_wake_enable_7216(params, false);
|
|
usb_init_common(params);
|
|
}
|
|
|
|
static void usb_init_xhci(struct brcm_usb_init_params *params)
|
|
{
|
|
pr_debug("%s\n", __func__);
|
|
|
|
xhci_soft_reset(params, 0);
|
|
}
|
|
|
|
static void usb_uninit_common_7216(struct brcm_usb_init_params *params)
|
|
{
|
|
void __iomem *ctrl = params->regs[BRCM_REGS_CTRL];
|
|
|
|
pr_debug("%s\n", __func__);
|
|
|
|
if (params->wake_enabled) {
|
|
/* Switch to using slower clock during suspend to save power */
|
|
USB_CTRL_SET(ctrl, USB_PM, XHC_S2_CLK_SWITCH_EN);
|
|
usb_wake_enable_7216(params, true);
|
|
} else {
|
|
USB_CTRL_SET(ctrl, USB_PM, USB_PWRDN);
|
|
}
|
|
}
|
|
|
|
static void usb_uninit_common_7211b0(struct brcm_usb_init_params *params)
|
|
{
|
|
void __iomem *ctrl = params->regs[BRCM_REGS_CTRL];
|
|
void __iomem *usb_phy = params->regs[BRCM_REGS_USB_PHY];
|
|
u32 reg;
|
|
|
|
pr_debug("%s\n", __func__);
|
|
|
|
if (params->wake_enabled) {
|
|
USB_CTRL_SET(ctrl, TEST_PORT_CTL, TPOUT_SEL_PME_GEN);
|
|
usb_wake_enable_7211b0(params, true);
|
|
} else {
|
|
USB_CTRL_SET(ctrl, USB_PM, USB_PWRDN);
|
|
brcm_usb_writel(0, usb_phy + USB_PHY_PLL_LDO_CTL);
|
|
reg = brcm_usb_readl(usb_phy + USB_PHY_PLL_CTL);
|
|
reg &= ~USB_PHY_PLL_CTL_PLL_RESETB_MASK;
|
|
brcm_usb_writel(reg, usb_phy + USB_PHY_PLL_CTL);
|
|
brcm_usb_writel(USB_PHY_IDDQ_phy_iddq_MASK,
|
|
usb_phy + USB_PHY_IDDQ);
|
|
}
|
|
|
|
}
|
|
|
|
static void usb_uninit_xhci(struct brcm_usb_init_params *params)
|
|
{
|
|
|
|
pr_debug("%s\n", __func__);
|
|
|
|
if (!params->wake_enabled)
|
|
xhci_soft_reset(params, 1);
|
|
}
|
|
|
|
static int usb_get_dual_select(struct brcm_usb_init_params *params)
|
|
{
|
|
void __iomem *ctrl = params->regs[BRCM_REGS_CTRL];
|
|
u32 reg = 0;
|
|
|
|
pr_debug("%s\n", __func__);
|
|
|
|
reg = brcm_usb_readl(USB_CTRL_REG(ctrl, USB_DEVICE_CTL1));
|
|
reg &= USB_CTRL_MASK(USB_DEVICE_CTL1, PORT_MODE);
|
|
return reg;
|
|
}
|
|
|
|
static void usb_set_dual_select(struct brcm_usb_init_params *params)
|
|
{
|
|
void __iomem *ctrl = params->regs[BRCM_REGS_CTRL];
|
|
u32 reg;
|
|
|
|
pr_debug("%s\n", __func__);
|
|
|
|
reg = brcm_usb_readl(USB_CTRL_REG(ctrl, USB_DEVICE_CTL1));
|
|
reg &= ~USB_CTRL_MASK(USB_DEVICE_CTL1, PORT_MODE);
|
|
reg |= params->port_mode;
|
|
brcm_usb_writel(reg, USB_CTRL_REG(ctrl, USB_DEVICE_CTL1));
|
|
}
|
|
|
|
static const struct brcm_usb_init_ops bcm7216_ops = {
|
|
.init_ipp = usb_init_ipp,
|
|
.init_common = usb_init_common_7216,
|
|
.init_xhci = usb_init_xhci,
|
|
.uninit_common = usb_uninit_common_7216,
|
|
.uninit_xhci = usb_uninit_xhci,
|
|
.get_dual_select = usb_get_dual_select,
|
|
.set_dual_select = usb_set_dual_select,
|
|
};
|
|
|
|
static const struct brcm_usb_init_ops bcm7211b0_ops = {
|
|
.init_ipp = usb_init_ipp,
|
|
.init_common = usb_init_common_7211b0,
|
|
.init_xhci = usb_init_xhci,
|
|
.uninit_common = usb_uninit_common_7211b0,
|
|
.uninit_xhci = usb_uninit_xhci,
|
|
.get_dual_select = usb_get_dual_select,
|
|
.set_dual_select = usb_set_dual_select,
|
|
};
|
|
|
|
void brcm_usb_dvr_init_7216(struct brcm_usb_init_params *params)
|
|
{
|
|
|
|
pr_debug("%s\n", __func__);
|
|
|
|
params->family_name = "7216";
|
|
params->ops = &bcm7216_ops;
|
|
}
|
|
|
|
void brcm_usb_dvr_init_7211b0(struct brcm_usb_init_params *params)
|
|
{
|
|
|
|
pr_debug("%s\n", __func__);
|
|
|
|
params->family_name = "7211";
|
|
params->ops = &bcm7211b0_ops;
|
|
}
|