117 lines
3.6 KiB
Plaintext
117 lines
3.6 KiB
Plaintext
MediaTek SoC built-in Bluetooth Devices
|
|
==================================
|
|
|
|
This device is a serial attached device to BTIF device and thus it must be a
|
|
child node of the serial node with BTIF. The dt-bindings details for BTIF
|
|
device can be known via Documentation/devicetree/bindings/serial/8250.yaml.
|
|
|
|
Required properties:
|
|
|
|
- compatible: Must be
|
|
"mediatek,mt7622-bluetooth": for MT7622 SoC
|
|
- clocks: Should be the clock specifiers corresponding to the entry in
|
|
clock-names property.
|
|
- clock-names: Should contain "ref" entries.
|
|
- power-domains: Phandle to the power domain that the device is part of
|
|
|
|
Example:
|
|
|
|
btif: serial@1100c000 {
|
|
compatible = "mediatek,mt7622-btif",
|
|
"mediatek,mtk-btif";
|
|
reg = <0 0x1100c000 0 0x1000>;
|
|
interrupts = <GIC_SPI 90 IRQ_TYPE_LEVEL_LOW>;
|
|
clocks = <&pericfg CLK_PERI_BTIF_PD>;
|
|
clock-names = "main";
|
|
reg-shift = <2>;
|
|
reg-io-width = <4>;
|
|
|
|
bluetooth {
|
|
compatible = "mediatek,mt7622-bluetooth";
|
|
power-domains = <&scpsys MT7622_POWER_DOMAIN_WB>;
|
|
clocks = <&clk25m>;
|
|
clock-names = "ref";
|
|
};
|
|
};
|
|
|
|
MediaTek UART based Bluetooth Devices
|
|
==================================
|
|
|
|
This device is a serial attached device to UART device and thus it must be a
|
|
child node of the serial node with UART.
|
|
|
|
Please refer to the following documents for generic properties:
|
|
|
|
Documentation/devicetree/bindings/serial/serial.yaml
|
|
|
|
Required properties:
|
|
|
|
- compatible: Must be
|
|
"mediatek,mt7663u-bluetooth": for MT7663U device
|
|
"mediatek,mt7668u-bluetooth": for MT7668U device
|
|
- vcc-supply: Main voltage regulator
|
|
|
|
If the pin controller on the platform can support both pinmux and GPIO
|
|
control such as the most of MediaTek platform. Please use below properties.
|
|
|
|
- pinctrl-names: Should be "default", "runtime"
|
|
- pinctrl-0: Should contain UART RXD low when the device is powered up to
|
|
enter proper bootstrap mode.
|
|
- pinctrl-1: Should contain UART mode pin ctrl
|
|
|
|
Else, the pin controller on the platform only can support pinmux control and
|
|
the GPIO control still has to rely on the dedicated GPIO controller such as
|
|
a legacy MediaTek SoC, MT7621. Please use the below properties.
|
|
|
|
- boot-gpios: GPIO same to the pin as UART RXD and used to keep LOW when
|
|
the device is powered up to enter proper bootstrap mode when
|
|
- pinctrl-names: Should be "default"
|
|
- pinctrl-0: Should contain UART mode pin ctrl
|
|
|
|
Optional properties:
|
|
|
|
- reset-gpios: GPIO used to reset the device whose initial state keeps low,
|
|
if the GPIO is missing, then board-level design should be
|
|
guaranteed.
|
|
- clocks: Should be the clock specifiers corresponding to the entry in
|
|
clock-names property. If the clock is missing, then board-level
|
|
design should be guaranteed.
|
|
- clock-names: Should contain "osc" entry for the external oscillator.
|
|
- current-speed: Current baud rate of the device whose defaults to 921600
|
|
|
|
Example:
|
|
|
|
uart1_pins_boot: uart1-default {
|
|
pins-dat {
|
|
pinmux = <MT7623_PIN_81_URXD1_FUNC_GPIO81>;
|
|
output-low;
|
|
};
|
|
};
|
|
|
|
uart1_pins_runtime: uart1-runtime {
|
|
pins-dat {
|
|
pinmux = <MT7623_PIN_81_URXD1_FUNC_URXD1>,
|
|
<MT7623_PIN_82_UTXD1_FUNC_UTXD1>;
|
|
};
|
|
};
|
|
|
|
uart1: serial@11003000 {
|
|
compatible = "mediatek,mt7623-uart",
|
|
"mediatek,mt6577-uart";
|
|
reg = <0 0x11003000 0 0x400>;
|
|
interrupts = <GIC_SPI 52 IRQ_TYPE_LEVEL_LOW>;
|
|
clocks = <&pericfg CLK_PERI_UART1_SEL>,
|
|
<&pericfg CLK_PERI_UART1>;
|
|
clock-names = "baud", "bus";
|
|
|
|
bluetooth {
|
|
compatible = "mediatek,mt7663u-bluetooth";
|
|
vcc-supply = <®_5v>;
|
|
reset-gpios = <&pio 24 GPIO_ACTIVE_LOW>;
|
|
pinctrl-names = "default", "runtime";
|
|
pinctrl-0 = <&uart1_pins_boot>;
|
|
pinctrl-1 = <&uart1_pins_runtime>;
|
|
current-speed = <921600>;
|
|
};
|
|
};
|