251 lines
7.1 KiB
YAML
251 lines
7.1 KiB
YAML
# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
|
|
%YAML 1.2
|
|
---
|
|
$id: http://devicetree.org/schemas/pinctrl/mediatek,mt6779-pinctrl.yaml#
|
|
$schema: http://devicetree.org/meta-schemas/core.yaml#
|
|
|
|
title: Mediatek MT6779 Pin Controller
|
|
|
|
maintainers:
|
|
- Andy Teng <andy.teng@mediatek.com>
|
|
- Sean Wang <sean.wang@kernel.org>
|
|
|
|
description:
|
|
The MediaTek pin controller on MT6779 is used to control pin
|
|
functions, pull up/down resistance and drive strength options.
|
|
|
|
properties:
|
|
compatible:
|
|
enum:
|
|
- mediatek,mt6779-pinctrl
|
|
- mediatek,mt6797-pinctrl
|
|
|
|
reg:
|
|
description: Physical addresses for GPIO base(s) and EINT registers.
|
|
|
|
reg-names: true
|
|
|
|
gpio-controller: true
|
|
|
|
"#gpio-cells":
|
|
const: 2
|
|
description: |
|
|
Number of cells in GPIO specifier. Since the generic GPIO
|
|
binding is used, the amount of cells must be specified as 2. See the below
|
|
mentioned gpio binding representation for description of particular cells.
|
|
|
|
gpio-ranges:
|
|
minItems: 1
|
|
maxItems: 5
|
|
description: |
|
|
GPIO valid number range.
|
|
|
|
interrupt-controller: true
|
|
|
|
interrupts:
|
|
maxItems: 1
|
|
description: |
|
|
Specifies the summary IRQ.
|
|
|
|
"#interrupt-cells":
|
|
const: 2
|
|
|
|
required:
|
|
- compatible
|
|
- reg
|
|
- reg-names
|
|
- gpio-controller
|
|
- "#gpio-cells"
|
|
|
|
allOf:
|
|
- $ref: "pinctrl.yaml#"
|
|
- if:
|
|
properties:
|
|
compatible:
|
|
contains:
|
|
const: mediatek,mt6779-pinctrl
|
|
then:
|
|
properties:
|
|
reg:
|
|
minItems: 9
|
|
maxItems: 9
|
|
|
|
reg-names:
|
|
items:
|
|
- const: gpio
|
|
- const: iocfg_rm
|
|
- const: iocfg_br
|
|
- const: iocfg_lm
|
|
- const: iocfg_lb
|
|
- const: iocfg_rt
|
|
- const: iocfg_lt
|
|
- const: iocfg_tl
|
|
- const: eint
|
|
- if:
|
|
properties:
|
|
compatible:
|
|
contains:
|
|
const: mediatek,mt6797-pinctrl
|
|
then:
|
|
properties:
|
|
reg:
|
|
minItems: 5
|
|
maxItems: 5
|
|
|
|
reg-names:
|
|
items:
|
|
- const: gpio
|
|
- const: iocfgl
|
|
- const: iocfgb
|
|
- const: iocfgr
|
|
- const: iocfgt
|
|
- if:
|
|
properties:
|
|
reg-names:
|
|
contains:
|
|
const: eint
|
|
then:
|
|
required:
|
|
- interrupts
|
|
- interrupt-controller
|
|
- "#interrupt-cells"
|
|
|
|
patternProperties:
|
|
'-[0-9]*$':
|
|
type: object
|
|
additionalProperties: false
|
|
|
|
patternProperties:
|
|
'-pins*$':
|
|
type: object
|
|
description: |
|
|
A pinctrl node should contain at least one subnodes representing the
|
|
pinctrl groups available on the machine. Each subnode will list the
|
|
pins it needs, and how they should be configured, with regard to muxer
|
|
configuration, pullups, drive strength, input enable/disable and input schmitt.
|
|
$ref: "/schemas/pinctrl/pincfg-node.yaml"
|
|
|
|
properties:
|
|
pinmux:
|
|
description:
|
|
integer array, represents gpio pin number and mux setting.
|
|
Supported pin number and mux varies for different SoCs, and are defined
|
|
as macros in boot/dts/<soc>-pinfunc.h directly.
|
|
|
|
bias-disable: true
|
|
|
|
bias-pull-up: true
|
|
|
|
bias-pull-down: true
|
|
|
|
input-enable: true
|
|
|
|
input-disable: true
|
|
|
|
output-low: true
|
|
|
|
output-high: true
|
|
|
|
input-schmitt-enable: true
|
|
|
|
input-schmitt-disable: true
|
|
|
|
drive-strength:
|
|
enum: [2, 4, 8, 12, 16]
|
|
|
|
slew-rate:
|
|
enum: [0, 1]
|
|
|
|
mediatek,pull-up-adv:
|
|
description: |
|
|
Pull up setings for 2 pull resistors, R0 and R1. User can
|
|
configure those special pins. Valid arguments are described as below:
|
|
0: (R1, R0) = (0, 0) which means R1 disabled and R0 disabled.
|
|
1: (R1, R0) = (0, 1) which means R1 disabled and R0 enabled.
|
|
2: (R1, R0) = (1, 0) which means R1 enabled and R0 disabled.
|
|
3: (R1, R0) = (1, 1) which means R1 enabled and R0 enabled.
|
|
$ref: /schemas/types.yaml#/definitions/uint32
|
|
enum: [0, 1, 2, 3]
|
|
|
|
mediatek,pull-down-adv:
|
|
description: |
|
|
Pull down settings for 2 pull resistors, R0 and R1. User can
|
|
configure those special pins. Valid arguments are described as below:
|
|
0: (R1, R0) = (0, 0) which means R1 disabled and R0 disabled.
|
|
1: (R1, R0) = (0, 1) which means R1 disabled and R0 enabled.
|
|
2: (R1, R0) = (1, 0) which means R1 enabled and R0 disabled.
|
|
3: (R1, R0) = (1, 1) which means R1 enabled and R0 enabled.
|
|
$ref: /schemas/types.yaml#/definitions/uint32
|
|
enum: [0, 1, 2, 3]
|
|
|
|
required:
|
|
- pinmux
|
|
|
|
additionalProperties: false
|
|
|
|
additionalProperties: false
|
|
|
|
examples:
|
|
- |
|
|
#include <dt-bindings/interrupt-controller/irq.h>
|
|
#include <dt-bindings/interrupt-controller/arm-gic.h>
|
|
#include <dt-bindings/pinctrl/mt6779-pinfunc.h>
|
|
|
|
soc {
|
|
#address-cells = <2>;
|
|
#size-cells = <2>;
|
|
|
|
pio: pinctrl@10005000 {
|
|
compatible = "mediatek,mt6779-pinctrl";
|
|
reg = <0 0x10005000 0 0x1000>,
|
|
<0 0x11c20000 0 0x1000>,
|
|
<0 0x11d10000 0 0x1000>,
|
|
<0 0x11e20000 0 0x1000>,
|
|
<0 0x11e70000 0 0x1000>,
|
|
<0 0x11ea0000 0 0x1000>,
|
|
<0 0x11f20000 0 0x1000>,
|
|
<0 0x11f30000 0 0x1000>,
|
|
<0 0x1000b000 0 0x1000>;
|
|
reg-names = "gpio", "iocfg_rm",
|
|
"iocfg_br", "iocfg_lm",
|
|
"iocfg_lb", "iocfg_rt",
|
|
"iocfg_lt", "iocfg_tl",
|
|
"eint";
|
|
gpio-controller;
|
|
#gpio-cells = <2>;
|
|
gpio-ranges = <&pio 0 0 210>;
|
|
interrupt-controller;
|
|
#interrupt-cells = <2>;
|
|
interrupts = <GIC_SPI 204 IRQ_TYPE_LEVEL_HIGH>;
|
|
|
|
mmc0_pins_default: mmc0-0 {
|
|
cmd-dat-pins {
|
|
pinmux = <PINMUX_GPIO168__FUNC_MSDC0_DAT0>,
|
|
<PINMUX_GPIO172__FUNC_MSDC0_DAT1>,
|
|
<PINMUX_GPIO169__FUNC_MSDC0_DAT2>,
|
|
<PINMUX_GPIO177__FUNC_MSDC0_DAT3>,
|
|
<PINMUX_GPIO170__FUNC_MSDC0_DAT4>,
|
|
<PINMUX_GPIO173__FUNC_MSDC0_DAT5>,
|
|
<PINMUX_GPIO171__FUNC_MSDC0_DAT6>,
|
|
<PINMUX_GPIO174__FUNC_MSDC0_DAT7>,
|
|
<PINMUX_GPIO167__FUNC_MSDC0_CMD>;
|
|
input-enable;
|
|
mediatek,pull-up-adv = <1>;
|
|
};
|
|
clk-pins {
|
|
pinmux = <PINMUX_GPIO176__FUNC_MSDC0_CLK>;
|
|
mediatek,pull-down-adv = <2>;
|
|
};
|
|
rst-pins {
|
|
pinmux = <PINMUX_GPIO178__FUNC_MSDC0_RSTB>;
|
|
mediatek,pull-up-adv = <0>;
|
|
};
|
|
};
|
|
};
|
|
|
|
mmc0 {
|
|
pinctrl-0 = <&mmc0_pins_default>;
|
|
pinctrl-names = "default";
|
|
};
|
|
};
|