128 lines
3.2 KiB
Plaintext
128 lines
3.2 KiB
Plaintext
// SPDX-License-Identifier: ISC
|
|
/*
|
|
* Device Tree file for the Intel IXDPG425 reference design.
|
|
* Derived from boardfiles written by MontaVista software.
|
|
* Ethernet set-up from OpenWrt.
|
|
*
|
|
* The device has 4 x FXS RJ11 ports for analog phones for
|
|
* internet telephony. (Not supported yet.)
|
|
*
|
|
* The device has 9 status LEDs we do not support yet.
|
|
*
|
|
* This device is very similar to ADI engingeering Coyote.
|
|
*/
|
|
|
|
/dts-v1/;
|
|
|
|
#include "intel-ixp42x.dtsi"
|
|
#include <dt-bindings/input/input.h>
|
|
|
|
/ {
|
|
model = "Intel IXDPG425 reference design";
|
|
compatible = "intel,ixdpg425", "intel,ixp42x";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
memory@0 {
|
|
/* 32 MB SDRAM */
|
|
device_type = "memory";
|
|
reg = <0x00000000 0x02000000>;
|
|
};
|
|
|
|
chosen {
|
|
bootargs = "console=ttyS0,115200n8 root=/dev/sda1 rw rootwait";
|
|
stdout-path = "uart0:115200n8";
|
|
};
|
|
|
|
aliases {
|
|
serial0 = &uart0;
|
|
};
|
|
|
|
soc {
|
|
bus@c4000000 {
|
|
flash@0,0 {
|
|
compatible = "intel,ixp4xx-flash", "cfi-flash";
|
|
bank-width = <2>;
|
|
/*
|
|
* CHECKME: the product brief says 16MB in a flash
|
|
* socket.
|
|
*/
|
|
reg = <0 0x00000000 0x1000000>;
|
|
|
|
/* Configure expansion bus to allow writes */
|
|
intel,ixp4xx-eb-write-enable = <1>;
|
|
|
|
partitions {
|
|
compatible = "redboot-fis";
|
|
/* CHECKME: guess this is Redboot FIS */
|
|
fis-index-block = <0x7f>;
|
|
};
|
|
};
|
|
};
|
|
|
|
pci@c0000000 {
|
|
status = "ok";
|
|
|
|
/*
|
|
* Taken from IXDPG425 PCI boardfile.
|
|
* We have slots (IDSEL) 12, 13 and 14 with one assigned IRQ
|
|
* for 12 & 13 and one for 14.
|
|
*/
|
|
#interrupt-cells = <1>;
|
|
interrupt-map-mask = <0xf800 0 0 7>;
|
|
interrupt-map =
|
|
/* IDSEL 12 */
|
|
<0x6000 0 0 1 &gpio0 7 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 12 is irq 7 */
|
|
<0x6000 0 0 2 &gpio0 7 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 12 is irq 7 */
|
|
<0x6000 0 0 3 &gpio0 7 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 12 is irq 7 */
|
|
<0x6000 0 0 4 &gpio0 7 IRQ_TYPE_LEVEL_LOW>, /* INT D on slot 12 is irq 7 */
|
|
/* IDSEL 13 */
|
|
<0x6800 0 0 1 &gpio0 7 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 13 is irq 7 */
|
|
<0x6800 0 0 2 &gpio0 7 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 13 is irq 7 */
|
|
<0x6800 0 0 3 &gpio0 7 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 13 is irq 7 */
|
|
<0x6800 0 0 4 &gpio0 7 IRQ_TYPE_LEVEL_LOW>, /* INT D on slot 13 is irq 7 */
|
|
/* IDSEL 14 */
|
|
<0x7000 0 0 1 &gpio0 6 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 14 is irq 6 */
|
|
<0x7000 0 0 2 &gpio0 6 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 14 is irq 6 */
|
|
<0x7000 0 0 3 &gpio0 6 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 14 is irq 6 */
|
|
<0x7000 0 0 4 &gpio0 6 IRQ_TYPE_LEVEL_LOW>; /* INT D on slot 14 is irq 6 */
|
|
};
|
|
|
|
/*
|
|
* CHECKME: this ethernet setup seems dubious. Photos of the board shows some kind
|
|
* of Realtek DSA switch on the board.
|
|
*/
|
|
|
|
/* EthB */
|
|
ethernet@c8009000 {
|
|
status = "ok";
|
|
queue-rx = <&qmgr 3>;
|
|
queue-txready = <&qmgr 20>;
|
|
phy-mode = "rgmii";
|
|
phy-handle = <&phy5>;
|
|
|
|
mdio {
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
phy4: ethernet-phy@4 {
|
|
reg = <4>;
|
|
};
|
|
|
|
phy5: ethernet-phy@5 {
|
|
reg = <5>;
|
|
};
|
|
};
|
|
};
|
|
|
|
/* EthC */
|
|
ethernet@c800a000 {
|
|
status = "ok";
|
|
queue-rx = <&qmgr 4>;
|
|
queue-txready = <&qmgr 21>;
|
|
phy-mode = "rgmii";
|
|
phy-handle = <&phy4>;
|
|
};
|
|
};
|
|
};
|