2149 lines
64 KiB
C
2149 lines
64 KiB
C
// SPDX-License-Identifier: GPL-2.0
|
|
/* Realtek SMI subdriver for the Realtek RTL8365MB-VC ethernet switch.
|
|
*
|
|
* Copyright (C) 2021 Alvin Šipraga <alsi@bang-olufsen.dk>
|
|
* Copyright (C) 2021 Michael Rasmussen <mir@bang-olufsen.dk>
|
|
*
|
|
* The RTL8365MB-VC is a 4+1 port 10/100/1000M switch controller. It includes 4
|
|
* integrated PHYs for the user facing ports, and an extension interface which
|
|
* can be connected to the CPU - or another PHY - via either MII, RMII, or
|
|
* RGMII. The switch is configured via the Realtek Simple Management Interface
|
|
* (SMI), which uses the MDIO/MDC lines.
|
|
*
|
|
* Below is a simplified block diagram of the chip and its relevant interfaces.
|
|
*
|
|
* .-----------------------------------.
|
|
* | |
|
|
* UTP <---------------> Giga PHY <-> PCS <-> P0 GMAC |
|
|
* UTP <---------------> Giga PHY <-> PCS <-> P1 GMAC |
|
|
* UTP <---------------> Giga PHY <-> PCS <-> P2 GMAC |
|
|
* UTP <---------------> Giga PHY <-> PCS <-> P3 GMAC |
|
|
* | |
|
|
* CPU/PHY <-MII/RMII/RGMII---> Extension <---> Extension |
|
|
* | interface 1 GMAC 1 |
|
|
* | |
|
|
* SMI driver/ <-MDC/SCL---> Management ~~~~~~~~~~~~~~ |
|
|
* EEPROM <-MDIO/SDA--> interface ~REALTEK ~~~~~ |
|
|
* | ~RTL8365MB ~~~ |
|
|
* | ~GXXXC TAIWAN~ |
|
|
* GPIO <--------------> Reset ~~~~~~~~~~~~~~ |
|
|
* | |
|
|
* Interrupt <----------> Link UP/DOWN events |
|
|
* controller | |
|
|
* '-----------------------------------'
|
|
*
|
|
* The driver uses DSA to integrate the 4 user and 1 extension ports into the
|
|
* kernel. Netdevices are created for the user ports, as are PHY devices for
|
|
* their integrated PHYs. The device tree firmware should also specify the link
|
|
* partner of the extension port - either via a fixed-link or other phy-handle.
|
|
* See the device tree bindings for more detailed information. Note that the
|
|
* driver has only been tested with a fixed-link, but in principle it should not
|
|
* matter.
|
|
*
|
|
* NOTE: Currently, only the RGMII interface is implemented in this driver.
|
|
*
|
|
* The interrupt line is asserted on link UP/DOWN events. The driver creates a
|
|
* custom irqchip to handle this interrupt and demultiplex the events by reading
|
|
* the status registers via SMI. Interrupts are then propagated to the relevant
|
|
* PHY device.
|
|
*
|
|
* The EEPROM contains initial register values which the chip will read over I2C
|
|
* upon hardware reset. It is also possible to omit the EEPROM. In both cases,
|
|
* the driver will manually reprogram some registers using jam tables to reach
|
|
* an initial state defined by the vendor driver.
|
|
*
|
|
* This Linux driver is written based on an OS-agnostic vendor driver from
|
|
* Realtek. The reference GPL-licensed sources can be found in the OpenWrt
|
|
* source tree under the name rtl8367c. The vendor driver claims to support a
|
|
* number of similar switch controllers from Realtek, but the only hardware we
|
|
* have is the RTL8365MB-VC. Moreover, there does not seem to be any chip under
|
|
* the name RTL8367C. Although one wishes that the 'C' stood for some kind of
|
|
* common hardware revision, there exist examples of chips with the suffix -VC
|
|
* which are explicitly not supported by the rtl8367c driver and which instead
|
|
* require the rtl8367d vendor driver. With all this uncertainty, the driver has
|
|
* been modestly named rtl8365mb. Future implementors may wish to rename things
|
|
* accordingly.
|
|
*
|
|
* In the same family of chips, some carry up to 8 user ports and up to 2
|
|
* extension ports. Where possible this driver tries to make things generic, but
|
|
* more work must be done to support these configurations. According to
|
|
* documentation from Realtek, the family should include the following chips:
|
|
*
|
|
* - RTL8363NB
|
|
* - RTL8363NB-VB
|
|
* - RTL8363SC
|
|
* - RTL8363SC-VB
|
|
* - RTL8364NB
|
|
* - RTL8364NB-VB
|
|
* - RTL8365MB-VC
|
|
* - RTL8366SC
|
|
* - RTL8367RB-VB
|
|
* - RTL8367SB
|
|
* - RTL8367S
|
|
* - RTL8370MB
|
|
* - RTL8310SR
|
|
*
|
|
* Some of the register logic for these additional chips has been skipped over
|
|
* while implementing this driver. It is therefore not possible to assume that
|
|
* things will work out-of-the-box for other chips, and a careful review of the
|
|
* vendor driver may be needed to expand support. The RTL8365MB-VC seems to be
|
|
* one of the simpler chips.
|
|
*/
|
|
|
|
#include <linux/bitfield.h>
|
|
#include <linux/bitops.h>
|
|
#include <linux/interrupt.h>
|
|
#include <linux/irqdomain.h>
|
|
#include <linux/mutex.h>
|
|
#include <linux/of_irq.h>
|
|
#include <linux/regmap.h>
|
|
#include <linux/if_bridge.h>
|
|
|
|
#include "realtek.h"
|
|
|
|
/* Family-specific data and limits */
|
|
#define RTL8365MB_PHYADDRMAX 7
|
|
#define RTL8365MB_NUM_PHYREGS 32
|
|
#define RTL8365MB_PHYREGMAX (RTL8365MB_NUM_PHYREGS - 1)
|
|
#define RTL8365MB_MAX_NUM_PORTS 11
|
|
#define RTL8365MB_MAX_NUM_EXTINTS 3
|
|
#define RTL8365MB_LEARN_LIMIT_MAX 2112
|
|
|
|
/* Chip identification registers */
|
|
#define RTL8365MB_CHIP_ID_REG 0x1300
|
|
|
|
#define RTL8365MB_CHIP_VER_REG 0x1301
|
|
|
|
#define RTL8365MB_MAGIC_REG 0x13C2
|
|
#define RTL8365MB_MAGIC_VALUE 0x0249
|
|
|
|
/* Chip reset register */
|
|
#define RTL8365MB_CHIP_RESET_REG 0x1322
|
|
#define RTL8365MB_CHIP_RESET_SW_MASK 0x0002
|
|
#define RTL8365MB_CHIP_RESET_HW_MASK 0x0001
|
|
|
|
/* Interrupt polarity register */
|
|
#define RTL8365MB_INTR_POLARITY_REG 0x1100
|
|
#define RTL8365MB_INTR_POLARITY_MASK 0x0001
|
|
#define RTL8365MB_INTR_POLARITY_HIGH 0
|
|
#define RTL8365MB_INTR_POLARITY_LOW 1
|
|
|
|
/* Interrupt control/status register - enable/check specific interrupt types */
|
|
#define RTL8365MB_INTR_CTRL_REG 0x1101
|
|
#define RTL8365MB_INTR_STATUS_REG 0x1102
|
|
#define RTL8365MB_INTR_SLIENT_START_2_MASK 0x1000
|
|
#define RTL8365MB_INTR_SLIENT_START_MASK 0x0800
|
|
#define RTL8365MB_INTR_ACL_ACTION_MASK 0x0200
|
|
#define RTL8365MB_INTR_CABLE_DIAG_FIN_MASK 0x0100
|
|
#define RTL8365MB_INTR_INTERRUPT_8051_MASK 0x0080
|
|
#define RTL8365MB_INTR_LOOP_DETECTION_MASK 0x0040
|
|
#define RTL8365MB_INTR_GREEN_TIMER_MASK 0x0020
|
|
#define RTL8365MB_INTR_SPECIAL_CONGEST_MASK 0x0010
|
|
#define RTL8365MB_INTR_SPEED_CHANGE_MASK 0x0008
|
|
#define RTL8365MB_INTR_LEARN_OVER_MASK 0x0004
|
|
#define RTL8365MB_INTR_METER_EXCEEDED_MASK 0x0002
|
|
#define RTL8365MB_INTR_LINK_CHANGE_MASK 0x0001
|
|
#define RTL8365MB_INTR_ALL_MASK \
|
|
(RTL8365MB_INTR_SLIENT_START_2_MASK | \
|
|
RTL8365MB_INTR_SLIENT_START_MASK | \
|
|
RTL8365MB_INTR_ACL_ACTION_MASK | \
|
|
RTL8365MB_INTR_CABLE_DIAG_FIN_MASK | \
|
|
RTL8365MB_INTR_INTERRUPT_8051_MASK | \
|
|
RTL8365MB_INTR_LOOP_DETECTION_MASK | \
|
|
RTL8365MB_INTR_GREEN_TIMER_MASK | \
|
|
RTL8365MB_INTR_SPECIAL_CONGEST_MASK | \
|
|
RTL8365MB_INTR_SPEED_CHANGE_MASK | \
|
|
RTL8365MB_INTR_LEARN_OVER_MASK | \
|
|
RTL8365MB_INTR_METER_EXCEEDED_MASK | \
|
|
RTL8365MB_INTR_LINK_CHANGE_MASK)
|
|
|
|
/* Per-port interrupt type status registers */
|
|
#define RTL8365MB_PORT_LINKDOWN_IND_REG 0x1106
|
|
#define RTL8365MB_PORT_LINKDOWN_IND_MASK 0x07FF
|
|
|
|
#define RTL8365MB_PORT_LINKUP_IND_REG 0x1107
|
|
#define RTL8365MB_PORT_LINKUP_IND_MASK 0x07FF
|
|
|
|
/* PHY indirect access registers */
|
|
#define RTL8365MB_INDIRECT_ACCESS_CTRL_REG 0x1F00
|
|
#define RTL8365MB_INDIRECT_ACCESS_CTRL_RW_MASK 0x0002
|
|
#define RTL8365MB_INDIRECT_ACCESS_CTRL_RW_READ 0
|
|
#define RTL8365MB_INDIRECT_ACCESS_CTRL_RW_WRITE 1
|
|
#define RTL8365MB_INDIRECT_ACCESS_CTRL_CMD_MASK 0x0001
|
|
#define RTL8365MB_INDIRECT_ACCESS_CTRL_CMD_VALUE 1
|
|
#define RTL8365MB_INDIRECT_ACCESS_STATUS_REG 0x1F01
|
|
#define RTL8365MB_INDIRECT_ACCESS_ADDRESS_REG 0x1F02
|
|
#define RTL8365MB_INDIRECT_ACCESS_ADDRESS_OCPADR_5_1_MASK GENMASK(4, 0)
|
|
#define RTL8365MB_INDIRECT_ACCESS_ADDRESS_PHYNUM_MASK GENMASK(7, 5)
|
|
#define RTL8365MB_INDIRECT_ACCESS_ADDRESS_OCPADR_9_6_MASK GENMASK(11, 8)
|
|
#define RTL8365MB_PHY_BASE 0x2000
|
|
#define RTL8365MB_INDIRECT_ACCESS_WRITE_DATA_REG 0x1F03
|
|
#define RTL8365MB_INDIRECT_ACCESS_READ_DATA_REG 0x1F04
|
|
|
|
/* PHY OCP address prefix register */
|
|
#define RTL8365MB_GPHY_OCP_MSB_0_REG 0x1D15
|
|
#define RTL8365MB_GPHY_OCP_MSB_0_CFG_CPU_OCPADR_MASK 0x0FC0
|
|
#define RTL8365MB_PHY_OCP_ADDR_PREFIX_MASK 0xFC00
|
|
|
|
/* The PHY OCP addresses of PHY registers 0~31 start here */
|
|
#define RTL8365MB_PHY_OCP_ADDR_PHYREG_BASE 0xA400
|
|
|
|
/* External interface port mode values - used in DIGITAL_INTERFACE_SELECT */
|
|
#define RTL8365MB_EXT_PORT_MODE_DISABLE 0
|
|
#define RTL8365MB_EXT_PORT_MODE_RGMII 1
|
|
#define RTL8365MB_EXT_PORT_MODE_MII_MAC 2
|
|
#define RTL8365MB_EXT_PORT_MODE_MII_PHY 3
|
|
#define RTL8365MB_EXT_PORT_MODE_TMII_MAC 4
|
|
#define RTL8365MB_EXT_PORT_MODE_TMII_PHY 5
|
|
#define RTL8365MB_EXT_PORT_MODE_GMII 6
|
|
#define RTL8365MB_EXT_PORT_MODE_RMII_MAC 7
|
|
#define RTL8365MB_EXT_PORT_MODE_RMII_PHY 8
|
|
#define RTL8365MB_EXT_PORT_MODE_SGMII 9
|
|
#define RTL8365MB_EXT_PORT_MODE_HSGMII 10
|
|
#define RTL8365MB_EXT_PORT_MODE_1000X_100FX 11
|
|
#define RTL8365MB_EXT_PORT_MODE_1000X 12
|
|
#define RTL8365MB_EXT_PORT_MODE_100FX 13
|
|
|
|
/* External interface mode configuration registers 0~1 */
|
|
#define RTL8365MB_DIGITAL_INTERFACE_SELECT_REG0 0x1305 /* EXT1 */
|
|
#define RTL8365MB_DIGITAL_INTERFACE_SELECT_REG1 0x13C3 /* EXT2 */
|
|
#define RTL8365MB_DIGITAL_INTERFACE_SELECT_REG(_extint) \
|
|
((_extint) == 1 ? RTL8365MB_DIGITAL_INTERFACE_SELECT_REG0 : \
|
|
(_extint) == 2 ? RTL8365MB_DIGITAL_INTERFACE_SELECT_REG1 : \
|
|
0x0)
|
|
#define RTL8365MB_DIGITAL_INTERFACE_SELECT_MODE_MASK(_extint) \
|
|
(0xF << (((_extint) % 2)))
|
|
#define RTL8365MB_DIGITAL_INTERFACE_SELECT_MODE_OFFSET(_extint) \
|
|
(((_extint) % 2) * 4)
|
|
|
|
/* External interface RGMII TX/RX delay configuration registers 0~2 */
|
|
#define RTL8365MB_EXT_RGMXF_REG0 0x1306 /* EXT0 */
|
|
#define RTL8365MB_EXT_RGMXF_REG1 0x1307 /* EXT1 */
|
|
#define RTL8365MB_EXT_RGMXF_REG2 0x13C5 /* EXT2 */
|
|
#define RTL8365MB_EXT_RGMXF_REG(_extint) \
|
|
((_extint) == 0 ? RTL8365MB_EXT_RGMXF_REG0 : \
|
|
(_extint) == 1 ? RTL8365MB_EXT_RGMXF_REG1 : \
|
|
(_extint) == 2 ? RTL8365MB_EXT_RGMXF_REG2 : \
|
|
0x0)
|
|
#define RTL8365MB_EXT_RGMXF_RXDELAY_MASK 0x0007
|
|
#define RTL8365MB_EXT_RGMXF_TXDELAY_MASK 0x0008
|
|
|
|
/* External interface port speed values - used in DIGITAL_INTERFACE_FORCE */
|
|
#define RTL8365MB_PORT_SPEED_10M 0
|
|
#define RTL8365MB_PORT_SPEED_100M 1
|
|
#define RTL8365MB_PORT_SPEED_1000M 2
|
|
|
|
/* External interface force configuration registers 0~2 */
|
|
#define RTL8365MB_DIGITAL_INTERFACE_FORCE_REG0 0x1310 /* EXT0 */
|
|
#define RTL8365MB_DIGITAL_INTERFACE_FORCE_REG1 0x1311 /* EXT1 */
|
|
#define RTL8365MB_DIGITAL_INTERFACE_FORCE_REG2 0x13C4 /* EXT2 */
|
|
#define RTL8365MB_DIGITAL_INTERFACE_FORCE_REG(_extint) \
|
|
((_extint) == 0 ? RTL8365MB_DIGITAL_INTERFACE_FORCE_REG0 : \
|
|
(_extint) == 1 ? RTL8365MB_DIGITAL_INTERFACE_FORCE_REG1 : \
|
|
(_extint) == 2 ? RTL8365MB_DIGITAL_INTERFACE_FORCE_REG2 : \
|
|
0x0)
|
|
#define RTL8365MB_DIGITAL_INTERFACE_FORCE_EN_MASK 0x1000
|
|
#define RTL8365MB_DIGITAL_INTERFACE_FORCE_NWAY_MASK 0x0080
|
|
#define RTL8365MB_DIGITAL_INTERFACE_FORCE_TXPAUSE_MASK 0x0040
|
|
#define RTL8365MB_DIGITAL_INTERFACE_FORCE_RXPAUSE_MASK 0x0020
|
|
#define RTL8365MB_DIGITAL_INTERFACE_FORCE_LINK_MASK 0x0010
|
|
#define RTL8365MB_DIGITAL_INTERFACE_FORCE_DUPLEX_MASK 0x0004
|
|
#define RTL8365MB_DIGITAL_INTERFACE_FORCE_SPEED_MASK 0x0003
|
|
|
|
/* CPU port mask register - controls which ports are treated as CPU ports */
|
|
#define RTL8365MB_CPU_PORT_MASK_REG 0x1219
|
|
#define RTL8365MB_CPU_PORT_MASK_MASK 0x07FF
|
|
|
|
/* CPU control register */
|
|
#define RTL8365MB_CPU_CTRL_REG 0x121A
|
|
#define RTL8365MB_CPU_CTRL_TRAP_PORT_EXT_MASK 0x0400
|
|
#define RTL8365MB_CPU_CTRL_TAG_FORMAT_MASK 0x0200
|
|
#define RTL8365MB_CPU_CTRL_RXBYTECOUNT_MASK 0x0080
|
|
#define RTL8365MB_CPU_CTRL_TAG_POSITION_MASK 0x0040
|
|
#define RTL8365MB_CPU_CTRL_TRAP_PORT_MASK 0x0038
|
|
#define RTL8365MB_CPU_CTRL_INSERTMODE_MASK 0x0006
|
|
#define RTL8365MB_CPU_CTRL_EN_MASK 0x0001
|
|
|
|
/* Maximum packet length register */
|
|
#define RTL8365MB_CFG0_MAX_LEN_REG 0x088C
|
|
#define RTL8365MB_CFG0_MAX_LEN_MASK 0x3FFF
|
|
|
|
/* Port learning limit registers */
|
|
#define RTL8365MB_LUT_PORT_LEARN_LIMIT_BASE 0x0A20
|
|
#define RTL8365MB_LUT_PORT_LEARN_LIMIT_REG(_physport) \
|
|
(RTL8365MB_LUT_PORT_LEARN_LIMIT_BASE + (_physport))
|
|
|
|
/* Port isolation (forwarding mask) registers */
|
|
#define RTL8365MB_PORT_ISOLATION_REG_BASE 0x08A2
|
|
#define RTL8365MB_PORT_ISOLATION_REG(_physport) \
|
|
(RTL8365MB_PORT_ISOLATION_REG_BASE + (_physport))
|
|
#define RTL8365MB_PORT_ISOLATION_MASK 0x07FF
|
|
|
|
/* MSTP port state registers - indexed by tree instance */
|
|
#define RTL8365MB_MSTI_CTRL_BASE 0x0A00
|
|
#define RTL8365MB_MSTI_CTRL_REG(_msti, _physport) \
|
|
(RTL8365MB_MSTI_CTRL_BASE + ((_msti) << 1) + ((_physport) >> 3))
|
|
#define RTL8365MB_MSTI_CTRL_PORT_STATE_OFFSET(_physport) ((_physport) << 1)
|
|
#define RTL8365MB_MSTI_CTRL_PORT_STATE_MASK(_physport) \
|
|
(0x3 << RTL8365MB_MSTI_CTRL_PORT_STATE_OFFSET((_physport)))
|
|
|
|
/* MIB counter value registers */
|
|
#define RTL8365MB_MIB_COUNTER_BASE 0x1000
|
|
#define RTL8365MB_MIB_COUNTER_REG(_x) (RTL8365MB_MIB_COUNTER_BASE + (_x))
|
|
|
|
/* MIB counter address register */
|
|
#define RTL8365MB_MIB_ADDRESS_REG 0x1004
|
|
#define RTL8365MB_MIB_ADDRESS_PORT_OFFSET 0x007C
|
|
#define RTL8365MB_MIB_ADDRESS(_p, _x) \
|
|
(((RTL8365MB_MIB_ADDRESS_PORT_OFFSET) * (_p) + (_x)) >> 2)
|
|
|
|
#define RTL8365MB_MIB_CTRL0_REG 0x1005
|
|
#define RTL8365MB_MIB_CTRL0_RESET_MASK 0x0002
|
|
#define RTL8365MB_MIB_CTRL0_BUSY_MASK 0x0001
|
|
|
|
/* The DSA callback .get_stats64 runs in atomic context, so we are not allowed
|
|
* to block. On the other hand, accessing MIB counters absolutely requires us to
|
|
* block. The solution is thus to schedule work which polls the MIB counters
|
|
* asynchronously and updates some private data, which the callback can then
|
|
* fetch atomically. Three seconds should be a good enough polling interval.
|
|
*/
|
|
#define RTL8365MB_STATS_INTERVAL_JIFFIES (3 * HZ)
|
|
|
|
enum rtl8365mb_mib_counter_index {
|
|
RTL8365MB_MIB_ifInOctets,
|
|
RTL8365MB_MIB_dot3StatsFCSErrors,
|
|
RTL8365MB_MIB_dot3StatsSymbolErrors,
|
|
RTL8365MB_MIB_dot3InPauseFrames,
|
|
RTL8365MB_MIB_dot3ControlInUnknownOpcodes,
|
|
RTL8365MB_MIB_etherStatsFragments,
|
|
RTL8365MB_MIB_etherStatsJabbers,
|
|
RTL8365MB_MIB_ifInUcastPkts,
|
|
RTL8365MB_MIB_etherStatsDropEvents,
|
|
RTL8365MB_MIB_ifInMulticastPkts,
|
|
RTL8365MB_MIB_ifInBroadcastPkts,
|
|
RTL8365MB_MIB_inMldChecksumError,
|
|
RTL8365MB_MIB_inIgmpChecksumError,
|
|
RTL8365MB_MIB_inMldSpecificQuery,
|
|
RTL8365MB_MIB_inMldGeneralQuery,
|
|
RTL8365MB_MIB_inIgmpSpecificQuery,
|
|
RTL8365MB_MIB_inIgmpGeneralQuery,
|
|
RTL8365MB_MIB_inMldLeaves,
|
|
RTL8365MB_MIB_inIgmpLeaves,
|
|
RTL8365MB_MIB_etherStatsOctets,
|
|
RTL8365MB_MIB_etherStatsUnderSizePkts,
|
|
RTL8365MB_MIB_etherOversizeStats,
|
|
RTL8365MB_MIB_etherStatsPkts64Octets,
|
|
RTL8365MB_MIB_etherStatsPkts65to127Octets,
|
|
RTL8365MB_MIB_etherStatsPkts128to255Octets,
|
|
RTL8365MB_MIB_etherStatsPkts256to511Octets,
|
|
RTL8365MB_MIB_etherStatsPkts512to1023Octets,
|
|
RTL8365MB_MIB_etherStatsPkts1024to1518Octets,
|
|
RTL8365MB_MIB_ifOutOctets,
|
|
RTL8365MB_MIB_dot3StatsSingleCollisionFrames,
|
|
RTL8365MB_MIB_dot3StatsMultipleCollisionFrames,
|
|
RTL8365MB_MIB_dot3StatsDeferredTransmissions,
|
|
RTL8365MB_MIB_dot3StatsLateCollisions,
|
|
RTL8365MB_MIB_etherStatsCollisions,
|
|
RTL8365MB_MIB_dot3StatsExcessiveCollisions,
|
|
RTL8365MB_MIB_dot3OutPauseFrames,
|
|
RTL8365MB_MIB_ifOutDiscards,
|
|
RTL8365MB_MIB_dot1dTpPortInDiscards,
|
|
RTL8365MB_MIB_ifOutUcastPkts,
|
|
RTL8365MB_MIB_ifOutMulticastPkts,
|
|
RTL8365MB_MIB_ifOutBroadcastPkts,
|
|
RTL8365MB_MIB_outOampduPkts,
|
|
RTL8365MB_MIB_inOampduPkts,
|
|
RTL8365MB_MIB_inIgmpJoinsSuccess,
|
|
RTL8365MB_MIB_inIgmpJoinsFail,
|
|
RTL8365MB_MIB_inMldJoinsSuccess,
|
|
RTL8365MB_MIB_inMldJoinsFail,
|
|
RTL8365MB_MIB_inReportSuppressionDrop,
|
|
RTL8365MB_MIB_inLeaveSuppressionDrop,
|
|
RTL8365MB_MIB_outIgmpReports,
|
|
RTL8365MB_MIB_outIgmpLeaves,
|
|
RTL8365MB_MIB_outIgmpGeneralQuery,
|
|
RTL8365MB_MIB_outIgmpSpecificQuery,
|
|
RTL8365MB_MIB_outMldReports,
|
|
RTL8365MB_MIB_outMldLeaves,
|
|
RTL8365MB_MIB_outMldGeneralQuery,
|
|
RTL8365MB_MIB_outMldSpecificQuery,
|
|
RTL8365MB_MIB_inKnownMulticastPkts,
|
|
RTL8365MB_MIB_END,
|
|
};
|
|
|
|
struct rtl8365mb_mib_counter {
|
|
u32 offset;
|
|
u32 length;
|
|
const char *name;
|
|
};
|
|
|
|
#define RTL8365MB_MAKE_MIB_COUNTER(_offset, _length, _name) \
|
|
[RTL8365MB_MIB_ ## _name] = { _offset, _length, #_name }
|
|
|
|
static struct rtl8365mb_mib_counter rtl8365mb_mib_counters[] = {
|
|
RTL8365MB_MAKE_MIB_COUNTER(0, 4, ifInOctets),
|
|
RTL8365MB_MAKE_MIB_COUNTER(4, 2, dot3StatsFCSErrors),
|
|
RTL8365MB_MAKE_MIB_COUNTER(6, 2, dot3StatsSymbolErrors),
|
|
RTL8365MB_MAKE_MIB_COUNTER(8, 2, dot3InPauseFrames),
|
|
RTL8365MB_MAKE_MIB_COUNTER(10, 2, dot3ControlInUnknownOpcodes),
|
|
RTL8365MB_MAKE_MIB_COUNTER(12, 2, etherStatsFragments),
|
|
RTL8365MB_MAKE_MIB_COUNTER(14, 2, etherStatsJabbers),
|
|
RTL8365MB_MAKE_MIB_COUNTER(16, 2, ifInUcastPkts),
|
|
RTL8365MB_MAKE_MIB_COUNTER(18, 2, etherStatsDropEvents),
|
|
RTL8365MB_MAKE_MIB_COUNTER(20, 2, ifInMulticastPkts),
|
|
RTL8365MB_MAKE_MIB_COUNTER(22, 2, ifInBroadcastPkts),
|
|
RTL8365MB_MAKE_MIB_COUNTER(24, 2, inMldChecksumError),
|
|
RTL8365MB_MAKE_MIB_COUNTER(26, 2, inIgmpChecksumError),
|
|
RTL8365MB_MAKE_MIB_COUNTER(28, 2, inMldSpecificQuery),
|
|
RTL8365MB_MAKE_MIB_COUNTER(30, 2, inMldGeneralQuery),
|
|
RTL8365MB_MAKE_MIB_COUNTER(32, 2, inIgmpSpecificQuery),
|
|
RTL8365MB_MAKE_MIB_COUNTER(34, 2, inIgmpGeneralQuery),
|
|
RTL8365MB_MAKE_MIB_COUNTER(36, 2, inMldLeaves),
|
|
RTL8365MB_MAKE_MIB_COUNTER(38, 2, inIgmpLeaves),
|
|
RTL8365MB_MAKE_MIB_COUNTER(40, 4, etherStatsOctets),
|
|
RTL8365MB_MAKE_MIB_COUNTER(44, 2, etherStatsUnderSizePkts),
|
|
RTL8365MB_MAKE_MIB_COUNTER(46, 2, etherOversizeStats),
|
|
RTL8365MB_MAKE_MIB_COUNTER(48, 2, etherStatsPkts64Octets),
|
|
RTL8365MB_MAKE_MIB_COUNTER(50, 2, etherStatsPkts65to127Octets),
|
|
RTL8365MB_MAKE_MIB_COUNTER(52, 2, etherStatsPkts128to255Octets),
|
|
RTL8365MB_MAKE_MIB_COUNTER(54, 2, etherStatsPkts256to511Octets),
|
|
RTL8365MB_MAKE_MIB_COUNTER(56, 2, etherStatsPkts512to1023Octets),
|
|
RTL8365MB_MAKE_MIB_COUNTER(58, 2, etherStatsPkts1024to1518Octets),
|
|
RTL8365MB_MAKE_MIB_COUNTER(60, 4, ifOutOctets),
|
|
RTL8365MB_MAKE_MIB_COUNTER(64, 2, dot3StatsSingleCollisionFrames),
|
|
RTL8365MB_MAKE_MIB_COUNTER(66, 2, dot3StatsMultipleCollisionFrames),
|
|
RTL8365MB_MAKE_MIB_COUNTER(68, 2, dot3StatsDeferredTransmissions),
|
|
RTL8365MB_MAKE_MIB_COUNTER(70, 2, dot3StatsLateCollisions),
|
|
RTL8365MB_MAKE_MIB_COUNTER(72, 2, etherStatsCollisions),
|
|
RTL8365MB_MAKE_MIB_COUNTER(74, 2, dot3StatsExcessiveCollisions),
|
|
RTL8365MB_MAKE_MIB_COUNTER(76, 2, dot3OutPauseFrames),
|
|
RTL8365MB_MAKE_MIB_COUNTER(78, 2, ifOutDiscards),
|
|
RTL8365MB_MAKE_MIB_COUNTER(80, 2, dot1dTpPortInDiscards),
|
|
RTL8365MB_MAKE_MIB_COUNTER(82, 2, ifOutUcastPkts),
|
|
RTL8365MB_MAKE_MIB_COUNTER(84, 2, ifOutMulticastPkts),
|
|
RTL8365MB_MAKE_MIB_COUNTER(86, 2, ifOutBroadcastPkts),
|
|
RTL8365MB_MAKE_MIB_COUNTER(88, 2, outOampduPkts),
|
|
RTL8365MB_MAKE_MIB_COUNTER(90, 2, inOampduPkts),
|
|
RTL8365MB_MAKE_MIB_COUNTER(92, 4, inIgmpJoinsSuccess),
|
|
RTL8365MB_MAKE_MIB_COUNTER(96, 2, inIgmpJoinsFail),
|
|
RTL8365MB_MAKE_MIB_COUNTER(98, 2, inMldJoinsSuccess),
|
|
RTL8365MB_MAKE_MIB_COUNTER(100, 2, inMldJoinsFail),
|
|
RTL8365MB_MAKE_MIB_COUNTER(102, 2, inReportSuppressionDrop),
|
|
RTL8365MB_MAKE_MIB_COUNTER(104, 2, inLeaveSuppressionDrop),
|
|
RTL8365MB_MAKE_MIB_COUNTER(106, 2, outIgmpReports),
|
|
RTL8365MB_MAKE_MIB_COUNTER(108, 2, outIgmpLeaves),
|
|
RTL8365MB_MAKE_MIB_COUNTER(110, 2, outIgmpGeneralQuery),
|
|
RTL8365MB_MAKE_MIB_COUNTER(112, 2, outIgmpSpecificQuery),
|
|
RTL8365MB_MAKE_MIB_COUNTER(114, 2, outMldReports),
|
|
RTL8365MB_MAKE_MIB_COUNTER(116, 2, outMldLeaves),
|
|
RTL8365MB_MAKE_MIB_COUNTER(118, 2, outMldGeneralQuery),
|
|
RTL8365MB_MAKE_MIB_COUNTER(120, 2, outMldSpecificQuery),
|
|
RTL8365MB_MAKE_MIB_COUNTER(122, 2, inKnownMulticastPkts),
|
|
};
|
|
|
|
static_assert(ARRAY_SIZE(rtl8365mb_mib_counters) == RTL8365MB_MIB_END);
|
|
|
|
struct rtl8365mb_jam_tbl_entry {
|
|
u16 reg;
|
|
u16 val;
|
|
};
|
|
|
|
/* Lifted from the vendor driver sources */
|
|
static const struct rtl8365mb_jam_tbl_entry rtl8365mb_init_jam_8365mb_vc[] = {
|
|
{ 0x13EB, 0x15BB }, { 0x1303, 0x06D6 }, { 0x1304, 0x0700 },
|
|
{ 0x13E2, 0x003F }, { 0x13F9, 0x0090 }, { 0x121E, 0x03CA },
|
|
{ 0x1233, 0x0352 }, { 0x1237, 0x00A0 }, { 0x123A, 0x0030 },
|
|
{ 0x1239, 0x0084 }, { 0x0301, 0x1000 }, { 0x1349, 0x001F },
|
|
{ 0x18E0, 0x4004 }, { 0x122B, 0x241C }, { 0x1305, 0xC000 },
|
|
{ 0x13F0, 0x0000 },
|
|
};
|
|
|
|
static const struct rtl8365mb_jam_tbl_entry rtl8365mb_init_jam_common[] = {
|
|
{ 0x1200, 0x7FCB }, { 0x0884, 0x0003 }, { 0x06EB, 0x0001 },
|
|
{ 0x03Fa, 0x0007 }, { 0x08C8, 0x00C0 }, { 0x0A30, 0x020E },
|
|
{ 0x0800, 0x0000 }, { 0x0802, 0x0000 }, { 0x09DA, 0x0013 },
|
|
{ 0x1D32, 0x0002 },
|
|
};
|
|
|
|
enum rtl8365mb_phy_interface_mode {
|
|
RTL8365MB_PHY_INTERFACE_MODE_INVAL = 0,
|
|
RTL8365MB_PHY_INTERFACE_MODE_INTERNAL = BIT(0),
|
|
RTL8365MB_PHY_INTERFACE_MODE_MII = BIT(1),
|
|
RTL8365MB_PHY_INTERFACE_MODE_TMII = BIT(2),
|
|
RTL8365MB_PHY_INTERFACE_MODE_RMII = BIT(3),
|
|
RTL8365MB_PHY_INTERFACE_MODE_RGMII = BIT(4),
|
|
RTL8365MB_PHY_INTERFACE_MODE_SGMII = BIT(5),
|
|
RTL8365MB_PHY_INTERFACE_MODE_HSGMII = BIT(6),
|
|
};
|
|
|
|
/**
|
|
* struct rtl8365mb_extint - external interface info
|
|
* @port: the port with an external interface
|
|
* @id: the external interface ID, which is either 0, 1, or 2
|
|
* @supported_interfaces: a bitmask of supported PHY interface modes
|
|
*
|
|
* Represents a mapping: port -> { id, supported_interfaces }. To be embedded
|
|
* in &struct rtl8365mb_chip_info for every port with an external interface.
|
|
*/
|
|
struct rtl8365mb_extint {
|
|
int port;
|
|
int id;
|
|
unsigned int supported_interfaces;
|
|
};
|
|
|
|
/**
|
|
* struct rtl8365mb_chip_info - static chip-specific info
|
|
* @name: human-readable chip name
|
|
* @chip_id: chip identifier
|
|
* @chip_ver: chip silicon revision
|
|
* @extints: available external interfaces
|
|
* @jam_table: chip-specific initialization jam table
|
|
* @jam_size: size of the chip's jam table
|
|
*
|
|
* These data are specific to a given chip in the family of switches supported
|
|
* by this driver. When adding support for another chip in the family, a new
|
|
* chip info should be added to the rtl8365mb_chip_infos array.
|
|
*/
|
|
struct rtl8365mb_chip_info {
|
|
const char *name;
|
|
u32 chip_id;
|
|
u32 chip_ver;
|
|
const struct rtl8365mb_extint extints[RTL8365MB_MAX_NUM_EXTINTS];
|
|
const struct rtl8365mb_jam_tbl_entry *jam_table;
|
|
size_t jam_size;
|
|
};
|
|
|
|
/* Chip info for each supported switch in the family */
|
|
#define PHY_INTF(_mode) (RTL8365MB_PHY_INTERFACE_MODE_ ## _mode)
|
|
static const struct rtl8365mb_chip_info rtl8365mb_chip_infos[] = {
|
|
{
|
|
.name = "RTL8365MB-VC",
|
|
.chip_id = 0x6367,
|
|
.chip_ver = 0x0040,
|
|
.extints = {
|
|
{ 6, 1, PHY_INTF(MII) | PHY_INTF(TMII) |
|
|
PHY_INTF(RMII) | PHY_INTF(RGMII) },
|
|
},
|
|
.jam_table = rtl8365mb_init_jam_8365mb_vc,
|
|
.jam_size = ARRAY_SIZE(rtl8365mb_init_jam_8365mb_vc),
|
|
},
|
|
{
|
|
.name = "RTL8367S",
|
|
.chip_id = 0x6367,
|
|
.chip_ver = 0x00A0,
|
|
.extints = {
|
|
{ 6, 1, PHY_INTF(SGMII) | PHY_INTF(HSGMII) },
|
|
{ 7, 2, PHY_INTF(MII) | PHY_INTF(TMII) |
|
|
PHY_INTF(RMII) | PHY_INTF(RGMII) },
|
|
},
|
|
.jam_table = rtl8365mb_init_jam_8365mb_vc,
|
|
.jam_size = ARRAY_SIZE(rtl8365mb_init_jam_8365mb_vc),
|
|
},
|
|
{
|
|
.name = "RTL8367RB-VB",
|
|
.chip_id = 0x6367,
|
|
.chip_ver = 0x0020,
|
|
.extints = {
|
|
{ 6, 1, PHY_INTF(MII) | PHY_INTF(TMII) |
|
|
PHY_INTF(RMII) | PHY_INTF(RGMII) },
|
|
{ 7, 2, PHY_INTF(MII) | PHY_INTF(TMII) |
|
|
PHY_INTF(RMII) | PHY_INTF(RGMII) },
|
|
},
|
|
.jam_table = rtl8365mb_init_jam_8365mb_vc,
|
|
.jam_size = ARRAY_SIZE(rtl8365mb_init_jam_8365mb_vc),
|
|
},
|
|
};
|
|
|
|
enum rtl8365mb_stp_state {
|
|
RTL8365MB_STP_STATE_DISABLED = 0,
|
|
RTL8365MB_STP_STATE_BLOCKING = 1,
|
|
RTL8365MB_STP_STATE_LEARNING = 2,
|
|
RTL8365MB_STP_STATE_FORWARDING = 3,
|
|
};
|
|
|
|
enum rtl8365mb_cpu_insert {
|
|
RTL8365MB_CPU_INSERT_TO_ALL = 0,
|
|
RTL8365MB_CPU_INSERT_TO_TRAPPING = 1,
|
|
RTL8365MB_CPU_INSERT_TO_NONE = 2,
|
|
};
|
|
|
|
enum rtl8365mb_cpu_position {
|
|
RTL8365MB_CPU_POS_AFTER_SA = 0,
|
|
RTL8365MB_CPU_POS_BEFORE_CRC = 1,
|
|
};
|
|
|
|
enum rtl8365mb_cpu_format {
|
|
RTL8365MB_CPU_FORMAT_8BYTES = 0,
|
|
RTL8365MB_CPU_FORMAT_4BYTES = 1,
|
|
};
|
|
|
|
enum rtl8365mb_cpu_rxlen {
|
|
RTL8365MB_CPU_RXLEN_72BYTES = 0,
|
|
RTL8365MB_CPU_RXLEN_64BYTES = 1,
|
|
};
|
|
|
|
/**
|
|
* struct rtl8365mb_cpu - CPU port configuration
|
|
* @enable: enable/disable hardware insertion of CPU tag in switch->CPU frames
|
|
* @mask: port mask of ports that parse should parse CPU tags
|
|
* @trap_port: forward trapped frames to this port
|
|
* @insert: CPU tag insertion mode in switch->CPU frames
|
|
* @position: position of CPU tag in frame
|
|
* @rx_length: minimum CPU RX length
|
|
* @format: CPU tag format
|
|
*
|
|
* Represents the CPU tagging and CPU port configuration of the switch. These
|
|
* settings are configurable at runtime.
|
|
*/
|
|
struct rtl8365mb_cpu {
|
|
bool enable;
|
|
u32 mask;
|
|
u32 trap_port;
|
|
enum rtl8365mb_cpu_insert insert;
|
|
enum rtl8365mb_cpu_position position;
|
|
enum rtl8365mb_cpu_rxlen rx_length;
|
|
enum rtl8365mb_cpu_format format;
|
|
};
|
|
|
|
/**
|
|
* struct rtl8365mb_port - private per-port data
|
|
* @priv: pointer to parent realtek_priv data
|
|
* @index: DSA port index, same as dsa_port::index
|
|
* @stats: link statistics populated by rtl8365mb_stats_poll, ready for atomic
|
|
* access via rtl8365mb_get_stats64
|
|
* @stats_lock: protect the stats structure during read/update
|
|
* @mib_work: delayed work for polling MIB counters
|
|
*/
|
|
struct rtl8365mb_port {
|
|
struct realtek_priv *priv;
|
|
unsigned int index;
|
|
struct rtnl_link_stats64 stats;
|
|
spinlock_t stats_lock;
|
|
struct delayed_work mib_work;
|
|
};
|
|
|
|
/**
|
|
* struct rtl8365mb - driver private data
|
|
* @priv: pointer to parent realtek_priv data
|
|
* @irq: registered IRQ or zero
|
|
* @chip_info: chip-specific info about the attached switch
|
|
* @cpu: CPU tagging and CPU port configuration for this chip
|
|
* @mib_lock: prevent concurrent reads of MIB counters
|
|
* @ports: per-port data
|
|
*
|
|
* Private data for this driver.
|
|
*/
|
|
struct rtl8365mb {
|
|
struct realtek_priv *priv;
|
|
int irq;
|
|
const struct rtl8365mb_chip_info *chip_info;
|
|
struct rtl8365mb_cpu cpu;
|
|
struct mutex mib_lock;
|
|
struct rtl8365mb_port ports[RTL8365MB_MAX_NUM_PORTS];
|
|
};
|
|
|
|
static int rtl8365mb_phy_poll_busy(struct realtek_priv *priv)
|
|
{
|
|
u32 val;
|
|
|
|
return regmap_read_poll_timeout(priv->map_nolock,
|
|
RTL8365MB_INDIRECT_ACCESS_STATUS_REG,
|
|
val, !val, 10, 100);
|
|
}
|
|
|
|
static int rtl8365mb_phy_ocp_prepare(struct realtek_priv *priv, int phy,
|
|
u32 ocp_addr)
|
|
{
|
|
u32 val;
|
|
int ret;
|
|
|
|
/* Set OCP prefix */
|
|
val = FIELD_GET(RTL8365MB_PHY_OCP_ADDR_PREFIX_MASK, ocp_addr);
|
|
ret = regmap_update_bits(
|
|
priv->map_nolock, RTL8365MB_GPHY_OCP_MSB_0_REG,
|
|
RTL8365MB_GPHY_OCP_MSB_0_CFG_CPU_OCPADR_MASK,
|
|
FIELD_PREP(RTL8365MB_GPHY_OCP_MSB_0_CFG_CPU_OCPADR_MASK, val));
|
|
if (ret)
|
|
return ret;
|
|
|
|
/* Set PHY register address */
|
|
val = RTL8365MB_PHY_BASE;
|
|
val |= FIELD_PREP(RTL8365MB_INDIRECT_ACCESS_ADDRESS_PHYNUM_MASK, phy);
|
|
val |= FIELD_PREP(RTL8365MB_INDIRECT_ACCESS_ADDRESS_OCPADR_5_1_MASK,
|
|
ocp_addr >> 1);
|
|
val |= FIELD_PREP(RTL8365MB_INDIRECT_ACCESS_ADDRESS_OCPADR_9_6_MASK,
|
|
ocp_addr >> 6);
|
|
ret = regmap_write(priv->map_nolock,
|
|
RTL8365MB_INDIRECT_ACCESS_ADDRESS_REG, val);
|
|
if (ret)
|
|
return ret;
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int rtl8365mb_phy_ocp_read(struct realtek_priv *priv, int phy,
|
|
u32 ocp_addr, u16 *data)
|
|
{
|
|
u32 val;
|
|
int ret;
|
|
|
|
mutex_lock(&priv->map_lock);
|
|
|
|
ret = rtl8365mb_phy_poll_busy(priv);
|
|
if (ret)
|
|
goto out;
|
|
|
|
ret = rtl8365mb_phy_ocp_prepare(priv, phy, ocp_addr);
|
|
if (ret)
|
|
goto out;
|
|
|
|
/* Execute read operation */
|
|
val = FIELD_PREP(RTL8365MB_INDIRECT_ACCESS_CTRL_CMD_MASK,
|
|
RTL8365MB_INDIRECT_ACCESS_CTRL_CMD_VALUE) |
|
|
FIELD_PREP(RTL8365MB_INDIRECT_ACCESS_CTRL_RW_MASK,
|
|
RTL8365MB_INDIRECT_ACCESS_CTRL_RW_READ);
|
|
ret = regmap_write(priv->map_nolock, RTL8365MB_INDIRECT_ACCESS_CTRL_REG,
|
|
val);
|
|
if (ret)
|
|
goto out;
|
|
|
|
ret = rtl8365mb_phy_poll_busy(priv);
|
|
if (ret)
|
|
goto out;
|
|
|
|
/* Get PHY register data */
|
|
ret = regmap_read(priv->map_nolock,
|
|
RTL8365MB_INDIRECT_ACCESS_READ_DATA_REG, &val);
|
|
if (ret)
|
|
goto out;
|
|
|
|
*data = val & 0xFFFF;
|
|
|
|
out:
|
|
mutex_unlock(&priv->map_lock);
|
|
|
|
return ret;
|
|
}
|
|
|
|
static int rtl8365mb_phy_ocp_write(struct realtek_priv *priv, int phy,
|
|
u32 ocp_addr, u16 data)
|
|
{
|
|
u32 val;
|
|
int ret;
|
|
|
|
mutex_lock(&priv->map_lock);
|
|
|
|
ret = rtl8365mb_phy_poll_busy(priv);
|
|
if (ret)
|
|
goto out;
|
|
|
|
ret = rtl8365mb_phy_ocp_prepare(priv, phy, ocp_addr);
|
|
if (ret)
|
|
goto out;
|
|
|
|
/* Set PHY register data */
|
|
ret = regmap_write(priv->map_nolock,
|
|
RTL8365MB_INDIRECT_ACCESS_WRITE_DATA_REG, data);
|
|
if (ret)
|
|
goto out;
|
|
|
|
/* Execute write operation */
|
|
val = FIELD_PREP(RTL8365MB_INDIRECT_ACCESS_CTRL_CMD_MASK,
|
|
RTL8365MB_INDIRECT_ACCESS_CTRL_CMD_VALUE) |
|
|
FIELD_PREP(RTL8365MB_INDIRECT_ACCESS_CTRL_RW_MASK,
|
|
RTL8365MB_INDIRECT_ACCESS_CTRL_RW_WRITE);
|
|
ret = regmap_write(priv->map_nolock, RTL8365MB_INDIRECT_ACCESS_CTRL_REG,
|
|
val);
|
|
if (ret)
|
|
goto out;
|
|
|
|
ret = rtl8365mb_phy_poll_busy(priv);
|
|
if (ret)
|
|
goto out;
|
|
|
|
out:
|
|
mutex_unlock(&priv->map_lock);
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int rtl8365mb_phy_read(struct realtek_priv *priv, int phy, int regnum)
|
|
{
|
|
u32 ocp_addr;
|
|
u16 val;
|
|
int ret;
|
|
|
|
if (phy > RTL8365MB_PHYADDRMAX)
|
|
return -EINVAL;
|
|
|
|
if (regnum > RTL8365MB_PHYREGMAX)
|
|
return -EINVAL;
|
|
|
|
ocp_addr = RTL8365MB_PHY_OCP_ADDR_PHYREG_BASE + regnum * 2;
|
|
|
|
ret = rtl8365mb_phy_ocp_read(priv, phy, ocp_addr, &val);
|
|
if (ret) {
|
|
dev_err(priv->dev,
|
|
"failed to read PHY%d reg %02x @ %04x, ret %d\n", phy,
|
|
regnum, ocp_addr, ret);
|
|
return ret;
|
|
}
|
|
|
|
dev_dbg(priv->dev, "read PHY%d register 0x%02x @ %04x, val <- %04x\n",
|
|
phy, regnum, ocp_addr, val);
|
|
|
|
return val;
|
|
}
|
|
|
|
static int rtl8365mb_phy_write(struct realtek_priv *priv, int phy, int regnum,
|
|
u16 val)
|
|
{
|
|
u32 ocp_addr;
|
|
int ret;
|
|
|
|
if (phy > RTL8365MB_PHYADDRMAX)
|
|
return -EINVAL;
|
|
|
|
if (regnum > RTL8365MB_PHYREGMAX)
|
|
return -EINVAL;
|
|
|
|
ocp_addr = RTL8365MB_PHY_OCP_ADDR_PHYREG_BASE + regnum * 2;
|
|
|
|
ret = rtl8365mb_phy_ocp_write(priv, phy, ocp_addr, val);
|
|
if (ret) {
|
|
dev_err(priv->dev,
|
|
"failed to write PHY%d reg %02x @ %04x, ret %d\n", phy,
|
|
regnum, ocp_addr, ret);
|
|
return ret;
|
|
}
|
|
|
|
dev_dbg(priv->dev, "write PHY%d register 0x%02x @ %04x, val -> %04x\n",
|
|
phy, regnum, ocp_addr, val);
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int rtl8365mb_dsa_phy_read(struct dsa_switch *ds, int phy, int regnum)
|
|
{
|
|
return rtl8365mb_phy_read(ds->priv, phy, regnum);
|
|
}
|
|
|
|
static int rtl8365mb_dsa_phy_write(struct dsa_switch *ds, int phy, int regnum,
|
|
u16 val)
|
|
{
|
|
return rtl8365mb_phy_write(ds->priv, phy, regnum, val);
|
|
}
|
|
|
|
static const struct rtl8365mb_extint *
|
|
rtl8365mb_get_port_extint(struct realtek_priv *priv, int port)
|
|
{
|
|
struct rtl8365mb *mb = priv->chip_data;
|
|
int i;
|
|
|
|
for (i = 0; i < RTL8365MB_MAX_NUM_EXTINTS; i++) {
|
|
const struct rtl8365mb_extint *extint =
|
|
&mb->chip_info->extints[i];
|
|
|
|
if (!extint->supported_interfaces)
|
|
continue;
|
|
|
|
if (extint->port == port)
|
|
return extint;
|
|
}
|
|
|
|
return NULL;
|
|
}
|
|
|
|
static enum dsa_tag_protocol
|
|
rtl8365mb_get_tag_protocol(struct dsa_switch *ds, int port,
|
|
enum dsa_tag_protocol mp)
|
|
{
|
|
struct realtek_priv *priv = ds->priv;
|
|
struct rtl8365mb_cpu *cpu;
|
|
struct rtl8365mb *mb;
|
|
|
|
mb = priv->chip_data;
|
|
cpu = &mb->cpu;
|
|
|
|
if (cpu->position == RTL8365MB_CPU_POS_BEFORE_CRC)
|
|
return DSA_TAG_PROTO_RTL8_4T;
|
|
|
|
return DSA_TAG_PROTO_RTL8_4;
|
|
}
|
|
|
|
static int rtl8365mb_ext_config_rgmii(struct realtek_priv *priv, int port,
|
|
phy_interface_t interface)
|
|
{
|
|
const struct rtl8365mb_extint *extint =
|
|
rtl8365mb_get_port_extint(priv, port);
|
|
struct device_node *dn;
|
|
struct dsa_port *dp;
|
|
int tx_delay = 0;
|
|
int rx_delay = 0;
|
|
u32 val;
|
|
int ret;
|
|
|
|
if (!extint)
|
|
return -ENODEV;
|
|
|
|
dp = dsa_to_port(priv->ds, port);
|
|
dn = dp->dn;
|
|
|
|
/* Set the RGMII TX/RX delay
|
|
*
|
|
* The Realtek vendor driver indicates the following possible
|
|
* configuration settings:
|
|
*
|
|
* TX delay:
|
|
* 0 = no delay, 1 = 2 ns delay
|
|
* RX delay:
|
|
* 0 = no delay, 7 = maximum delay
|
|
* Each step is approximately 0.3 ns, so the maximum delay is about
|
|
* 2.1 ns.
|
|
*
|
|
* The vendor driver also states that this must be configured *before*
|
|
* forcing the external interface into a particular mode, which is done
|
|
* in the rtl8365mb_phylink_mac_link_{up,down} functions.
|
|
*
|
|
* Only configure an RGMII TX (resp. RX) delay if the
|
|
* tx-internal-delay-ps (resp. rx-internal-delay-ps) OF property is
|
|
* specified. We ignore the detail of the RGMII interface mode
|
|
* (RGMII_{RXID, TXID, etc.}), as this is considered to be a PHY-only
|
|
* property.
|
|
*/
|
|
if (!of_property_read_u32(dn, "tx-internal-delay-ps", &val)) {
|
|
val = val / 1000; /* convert to ns */
|
|
|
|
if (val == 0 || val == 2)
|
|
tx_delay = val / 2;
|
|
else
|
|
dev_warn(priv->dev,
|
|
"RGMII TX delay must be 0 or 2 ns\n");
|
|
}
|
|
|
|
if (!of_property_read_u32(dn, "rx-internal-delay-ps", &val)) {
|
|
val = DIV_ROUND_CLOSEST(val, 300); /* convert to 0.3 ns step */
|
|
|
|
if (val <= 7)
|
|
rx_delay = val;
|
|
else
|
|
dev_warn(priv->dev,
|
|
"RGMII RX delay must be 0 to 2.1 ns\n");
|
|
}
|
|
|
|
ret = regmap_update_bits(
|
|
priv->map, RTL8365MB_EXT_RGMXF_REG(extint->id),
|
|
RTL8365MB_EXT_RGMXF_TXDELAY_MASK |
|
|
RTL8365MB_EXT_RGMXF_RXDELAY_MASK,
|
|
FIELD_PREP(RTL8365MB_EXT_RGMXF_TXDELAY_MASK, tx_delay) |
|
|
FIELD_PREP(RTL8365MB_EXT_RGMXF_RXDELAY_MASK, rx_delay));
|
|
if (ret)
|
|
return ret;
|
|
|
|
ret = regmap_update_bits(
|
|
priv->map, RTL8365MB_DIGITAL_INTERFACE_SELECT_REG(extint->id),
|
|
RTL8365MB_DIGITAL_INTERFACE_SELECT_MODE_MASK(extint->id),
|
|
RTL8365MB_EXT_PORT_MODE_RGMII
|
|
<< RTL8365MB_DIGITAL_INTERFACE_SELECT_MODE_OFFSET(
|
|
extint->id));
|
|
if (ret)
|
|
return ret;
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int rtl8365mb_ext_config_forcemode(struct realtek_priv *priv, int port,
|
|
bool link, int speed, int duplex,
|
|
bool tx_pause, bool rx_pause)
|
|
{
|
|
const struct rtl8365mb_extint *extint =
|
|
rtl8365mb_get_port_extint(priv, port);
|
|
u32 r_tx_pause;
|
|
u32 r_rx_pause;
|
|
u32 r_duplex;
|
|
u32 r_speed;
|
|
u32 r_link;
|
|
int val;
|
|
int ret;
|
|
|
|
if (!extint)
|
|
return -ENODEV;
|
|
|
|
if (link) {
|
|
/* Force the link up with the desired configuration */
|
|
r_link = 1;
|
|
r_rx_pause = rx_pause ? 1 : 0;
|
|
r_tx_pause = tx_pause ? 1 : 0;
|
|
|
|
if (speed == SPEED_1000) {
|
|
r_speed = RTL8365MB_PORT_SPEED_1000M;
|
|
} else if (speed == SPEED_100) {
|
|
r_speed = RTL8365MB_PORT_SPEED_100M;
|
|
} else if (speed == SPEED_10) {
|
|
r_speed = RTL8365MB_PORT_SPEED_10M;
|
|
} else {
|
|
dev_err(priv->dev, "unsupported port speed %s\n",
|
|
phy_speed_to_str(speed));
|
|
return -EINVAL;
|
|
}
|
|
|
|
if (duplex == DUPLEX_FULL) {
|
|
r_duplex = 1;
|
|
} else if (duplex == DUPLEX_HALF) {
|
|
r_duplex = 0;
|
|
} else {
|
|
dev_err(priv->dev, "unsupported duplex %s\n",
|
|
phy_duplex_to_str(duplex));
|
|
return -EINVAL;
|
|
}
|
|
} else {
|
|
/* Force the link down and reset any programmed configuration */
|
|
r_link = 0;
|
|
r_tx_pause = 0;
|
|
r_rx_pause = 0;
|
|
r_speed = 0;
|
|
r_duplex = 0;
|
|
}
|
|
|
|
val = FIELD_PREP(RTL8365MB_DIGITAL_INTERFACE_FORCE_EN_MASK, 1) |
|
|
FIELD_PREP(RTL8365MB_DIGITAL_INTERFACE_FORCE_TXPAUSE_MASK,
|
|
r_tx_pause) |
|
|
FIELD_PREP(RTL8365MB_DIGITAL_INTERFACE_FORCE_RXPAUSE_MASK,
|
|
r_rx_pause) |
|
|
FIELD_PREP(RTL8365MB_DIGITAL_INTERFACE_FORCE_LINK_MASK, r_link) |
|
|
FIELD_PREP(RTL8365MB_DIGITAL_INTERFACE_FORCE_DUPLEX_MASK,
|
|
r_duplex) |
|
|
FIELD_PREP(RTL8365MB_DIGITAL_INTERFACE_FORCE_SPEED_MASK, r_speed);
|
|
ret = regmap_write(priv->map,
|
|
RTL8365MB_DIGITAL_INTERFACE_FORCE_REG(extint->id),
|
|
val);
|
|
if (ret)
|
|
return ret;
|
|
|
|
return 0;
|
|
}
|
|
|
|
static void rtl8365mb_phylink_get_caps(struct dsa_switch *ds, int port,
|
|
struct phylink_config *config)
|
|
{
|
|
const struct rtl8365mb_extint *extint =
|
|
rtl8365mb_get_port_extint(ds->priv, port);
|
|
|
|
config->mac_capabilities = MAC_SYM_PAUSE | MAC_ASYM_PAUSE |
|
|
MAC_10 | MAC_100 | MAC_1000FD;
|
|
|
|
if (!extint) {
|
|
__set_bit(PHY_INTERFACE_MODE_INTERNAL,
|
|
config->supported_interfaces);
|
|
|
|
/* GMII is the default interface mode for phylib, so
|
|
* we have to support it for ports with integrated PHY.
|
|
*/
|
|
__set_bit(PHY_INTERFACE_MODE_GMII,
|
|
config->supported_interfaces);
|
|
return;
|
|
}
|
|
|
|
/* Populate according to the modes supported by _this driver_,
|
|
* not necessarily the modes supported by the hardware, some of
|
|
* which remain unimplemented.
|
|
*/
|
|
|
|
if (extint->supported_interfaces & RTL8365MB_PHY_INTERFACE_MODE_RGMII)
|
|
phy_interface_set_rgmii(config->supported_interfaces);
|
|
}
|
|
|
|
static void rtl8365mb_phylink_mac_config(struct dsa_switch *ds, int port,
|
|
unsigned int mode,
|
|
const struct phylink_link_state *state)
|
|
{
|
|
struct realtek_priv *priv = ds->priv;
|
|
int ret;
|
|
|
|
if (mode != MLO_AN_PHY && mode != MLO_AN_FIXED) {
|
|
dev_err(priv->dev,
|
|
"port %d supports only conventional PHY or fixed-link\n",
|
|
port);
|
|
return;
|
|
}
|
|
|
|
if (phy_interface_mode_is_rgmii(state->interface)) {
|
|
ret = rtl8365mb_ext_config_rgmii(priv, port, state->interface);
|
|
if (ret)
|
|
dev_err(priv->dev,
|
|
"failed to configure RGMII mode on port %d: %d\n",
|
|
port, ret);
|
|
return;
|
|
}
|
|
|
|
/* TODO: Implement MII and RMII modes, which the RTL8365MB-VC also
|
|
* supports
|
|
*/
|
|
}
|
|
|
|
static void rtl8365mb_phylink_mac_link_down(struct dsa_switch *ds, int port,
|
|
unsigned int mode,
|
|
phy_interface_t interface)
|
|
{
|
|
struct realtek_priv *priv = ds->priv;
|
|
struct rtl8365mb_port *p;
|
|
struct rtl8365mb *mb;
|
|
int ret;
|
|
|
|
mb = priv->chip_data;
|
|
p = &mb->ports[port];
|
|
cancel_delayed_work_sync(&p->mib_work);
|
|
|
|
if (phy_interface_mode_is_rgmii(interface)) {
|
|
ret = rtl8365mb_ext_config_forcemode(priv, port, false, 0, 0,
|
|
false, false);
|
|
if (ret)
|
|
dev_err(priv->dev,
|
|
"failed to reset forced mode on port %d: %d\n",
|
|
port, ret);
|
|
|
|
return;
|
|
}
|
|
}
|
|
|
|
static void rtl8365mb_phylink_mac_link_up(struct dsa_switch *ds, int port,
|
|
unsigned int mode,
|
|
phy_interface_t interface,
|
|
struct phy_device *phydev, int speed,
|
|
int duplex, bool tx_pause,
|
|
bool rx_pause)
|
|
{
|
|
struct realtek_priv *priv = ds->priv;
|
|
struct rtl8365mb_port *p;
|
|
struct rtl8365mb *mb;
|
|
int ret;
|
|
|
|
mb = priv->chip_data;
|
|
p = &mb->ports[port];
|
|
schedule_delayed_work(&p->mib_work, 0);
|
|
|
|
if (phy_interface_mode_is_rgmii(interface)) {
|
|
ret = rtl8365mb_ext_config_forcemode(priv, port, true, speed,
|
|
duplex, tx_pause,
|
|
rx_pause);
|
|
if (ret)
|
|
dev_err(priv->dev,
|
|
"failed to force mode on port %d: %d\n", port,
|
|
ret);
|
|
|
|
return;
|
|
}
|
|
}
|
|
|
|
static void rtl8365mb_port_stp_state_set(struct dsa_switch *ds, int port,
|
|
u8 state)
|
|
{
|
|
struct realtek_priv *priv = ds->priv;
|
|
enum rtl8365mb_stp_state val;
|
|
int msti = 0;
|
|
|
|
switch (state) {
|
|
case BR_STATE_DISABLED:
|
|
val = RTL8365MB_STP_STATE_DISABLED;
|
|
break;
|
|
case BR_STATE_BLOCKING:
|
|
case BR_STATE_LISTENING:
|
|
val = RTL8365MB_STP_STATE_BLOCKING;
|
|
break;
|
|
case BR_STATE_LEARNING:
|
|
val = RTL8365MB_STP_STATE_LEARNING;
|
|
break;
|
|
case BR_STATE_FORWARDING:
|
|
val = RTL8365MB_STP_STATE_FORWARDING;
|
|
break;
|
|
default:
|
|
dev_err(priv->dev, "invalid STP state: %u\n", state);
|
|
return;
|
|
}
|
|
|
|
regmap_update_bits(priv->map, RTL8365MB_MSTI_CTRL_REG(msti, port),
|
|
RTL8365MB_MSTI_CTRL_PORT_STATE_MASK(port),
|
|
val << RTL8365MB_MSTI_CTRL_PORT_STATE_OFFSET(port));
|
|
}
|
|
|
|
static int rtl8365mb_port_set_learning(struct realtek_priv *priv, int port,
|
|
bool enable)
|
|
{
|
|
/* Enable/disable learning by limiting the number of L2 addresses the
|
|
* port can learn. Realtek documentation states that a limit of zero
|
|
* disables learning. When enabling learning, set it to the chip's
|
|
* maximum.
|
|
*/
|
|
return regmap_write(priv->map, RTL8365MB_LUT_PORT_LEARN_LIMIT_REG(port),
|
|
enable ? RTL8365MB_LEARN_LIMIT_MAX : 0);
|
|
}
|
|
|
|
static int rtl8365mb_port_set_isolation(struct realtek_priv *priv, int port,
|
|
u32 mask)
|
|
{
|
|
return regmap_write(priv->map, RTL8365MB_PORT_ISOLATION_REG(port), mask);
|
|
}
|
|
|
|
static int rtl8365mb_mib_counter_read(struct realtek_priv *priv, int port,
|
|
u32 offset, u32 length, u64 *mibvalue)
|
|
{
|
|
u64 tmpvalue = 0;
|
|
u32 val;
|
|
int ret;
|
|
int i;
|
|
|
|
/* The MIB address is an SRAM address. We request a particular address
|
|
* and then poll the control register before reading the value from some
|
|
* counter registers.
|
|
*/
|
|
ret = regmap_write(priv->map, RTL8365MB_MIB_ADDRESS_REG,
|
|
RTL8365MB_MIB_ADDRESS(port, offset));
|
|
if (ret)
|
|
return ret;
|
|
|
|
/* Poll for completion */
|
|
ret = regmap_read_poll_timeout(priv->map, RTL8365MB_MIB_CTRL0_REG, val,
|
|
!(val & RTL8365MB_MIB_CTRL0_BUSY_MASK),
|
|
10, 100);
|
|
if (ret)
|
|
return ret;
|
|
|
|
/* Presumably this indicates a MIB counter read failure */
|
|
if (val & RTL8365MB_MIB_CTRL0_RESET_MASK)
|
|
return -EIO;
|
|
|
|
/* There are four MIB counter registers each holding a 16 bit word of a
|
|
* MIB counter. Depending on the offset, we should read from the upper
|
|
* two or lower two registers. In case the MIB counter is 4 words, we
|
|
* read from all four registers.
|
|
*/
|
|
if (length == 4)
|
|
offset = 3;
|
|
else
|
|
offset = (offset + 1) % 4;
|
|
|
|
/* Read the MIB counter 16 bits at a time */
|
|
for (i = 0; i < length; i++) {
|
|
ret = regmap_read(priv->map,
|
|
RTL8365MB_MIB_COUNTER_REG(offset - i), &val);
|
|
if (ret)
|
|
return ret;
|
|
|
|
tmpvalue = ((tmpvalue) << 16) | (val & 0xFFFF);
|
|
}
|
|
|
|
/* Only commit the result if no error occurred */
|
|
*mibvalue = tmpvalue;
|
|
|
|
return 0;
|
|
}
|
|
|
|
static void rtl8365mb_get_ethtool_stats(struct dsa_switch *ds, int port, u64 *data)
|
|
{
|
|
struct realtek_priv *priv = ds->priv;
|
|
struct rtl8365mb *mb;
|
|
int ret;
|
|
int i;
|
|
|
|
mb = priv->chip_data;
|
|
|
|
mutex_lock(&mb->mib_lock);
|
|
for (i = 0; i < RTL8365MB_MIB_END; i++) {
|
|
struct rtl8365mb_mib_counter *mib = &rtl8365mb_mib_counters[i];
|
|
|
|
ret = rtl8365mb_mib_counter_read(priv, port, mib->offset,
|
|
mib->length, &data[i]);
|
|
if (ret) {
|
|
dev_err(priv->dev,
|
|
"failed to read port %d counters: %d\n", port,
|
|
ret);
|
|
break;
|
|
}
|
|
}
|
|
mutex_unlock(&mb->mib_lock);
|
|
}
|
|
|
|
static void rtl8365mb_get_strings(struct dsa_switch *ds, int port, u32 stringset, u8 *data)
|
|
{
|
|
int i;
|
|
|
|
if (stringset != ETH_SS_STATS)
|
|
return;
|
|
|
|
for (i = 0; i < RTL8365MB_MIB_END; i++) {
|
|
struct rtl8365mb_mib_counter *mib = &rtl8365mb_mib_counters[i];
|
|
|
|
strncpy(data + i * ETH_GSTRING_LEN, mib->name, ETH_GSTRING_LEN);
|
|
}
|
|
}
|
|
|
|
static int rtl8365mb_get_sset_count(struct dsa_switch *ds, int port, int sset)
|
|
{
|
|
if (sset != ETH_SS_STATS)
|
|
return -EOPNOTSUPP;
|
|
|
|
return RTL8365MB_MIB_END;
|
|
}
|
|
|
|
static void rtl8365mb_get_phy_stats(struct dsa_switch *ds, int port,
|
|
struct ethtool_eth_phy_stats *phy_stats)
|
|
{
|
|
struct realtek_priv *priv = ds->priv;
|
|
struct rtl8365mb_mib_counter *mib;
|
|
struct rtl8365mb *mb;
|
|
|
|
mb = priv->chip_data;
|
|
mib = &rtl8365mb_mib_counters[RTL8365MB_MIB_dot3StatsSymbolErrors];
|
|
|
|
mutex_lock(&mb->mib_lock);
|
|
rtl8365mb_mib_counter_read(priv, port, mib->offset, mib->length,
|
|
&phy_stats->SymbolErrorDuringCarrier);
|
|
mutex_unlock(&mb->mib_lock);
|
|
}
|
|
|
|
static void rtl8365mb_get_mac_stats(struct dsa_switch *ds, int port,
|
|
struct ethtool_eth_mac_stats *mac_stats)
|
|
{
|
|
u64 cnt[RTL8365MB_MIB_END] = {
|
|
[RTL8365MB_MIB_ifOutOctets] = 1,
|
|
[RTL8365MB_MIB_ifOutUcastPkts] = 1,
|
|
[RTL8365MB_MIB_ifOutMulticastPkts] = 1,
|
|
[RTL8365MB_MIB_ifOutBroadcastPkts] = 1,
|
|
[RTL8365MB_MIB_dot3OutPauseFrames] = 1,
|
|
[RTL8365MB_MIB_ifOutDiscards] = 1,
|
|
[RTL8365MB_MIB_ifInOctets] = 1,
|
|
[RTL8365MB_MIB_ifInUcastPkts] = 1,
|
|
[RTL8365MB_MIB_ifInMulticastPkts] = 1,
|
|
[RTL8365MB_MIB_ifInBroadcastPkts] = 1,
|
|
[RTL8365MB_MIB_dot3InPauseFrames] = 1,
|
|
[RTL8365MB_MIB_dot3StatsSingleCollisionFrames] = 1,
|
|
[RTL8365MB_MIB_dot3StatsMultipleCollisionFrames] = 1,
|
|
[RTL8365MB_MIB_dot3StatsFCSErrors] = 1,
|
|
[RTL8365MB_MIB_dot3StatsDeferredTransmissions] = 1,
|
|
[RTL8365MB_MIB_dot3StatsLateCollisions] = 1,
|
|
[RTL8365MB_MIB_dot3StatsExcessiveCollisions] = 1,
|
|
|
|
};
|
|
struct realtek_priv *priv = ds->priv;
|
|
struct rtl8365mb *mb;
|
|
int ret;
|
|
int i;
|
|
|
|
mb = priv->chip_data;
|
|
|
|
mutex_lock(&mb->mib_lock);
|
|
for (i = 0; i < RTL8365MB_MIB_END; i++) {
|
|
struct rtl8365mb_mib_counter *mib = &rtl8365mb_mib_counters[i];
|
|
|
|
/* Only fetch required MIB counters (marked = 1 above) */
|
|
if (!cnt[i])
|
|
continue;
|
|
|
|
ret = rtl8365mb_mib_counter_read(priv, port, mib->offset,
|
|
mib->length, &cnt[i]);
|
|
if (ret)
|
|
break;
|
|
}
|
|
mutex_unlock(&mb->mib_lock);
|
|
|
|
/* The RTL8365MB-VC exposes MIB objects, which we have to translate into
|
|
* IEEE 802.3 Managed Objects. This is not always completely faithful,
|
|
* but we try out best. See RFC 3635 for a detailed treatment of the
|
|
* subject.
|
|
*/
|
|
|
|
mac_stats->FramesTransmittedOK = cnt[RTL8365MB_MIB_ifOutUcastPkts] +
|
|
cnt[RTL8365MB_MIB_ifOutMulticastPkts] +
|
|
cnt[RTL8365MB_MIB_ifOutBroadcastPkts] +
|
|
cnt[RTL8365MB_MIB_dot3OutPauseFrames] -
|
|
cnt[RTL8365MB_MIB_ifOutDiscards];
|
|
mac_stats->SingleCollisionFrames =
|
|
cnt[RTL8365MB_MIB_dot3StatsSingleCollisionFrames];
|
|
mac_stats->MultipleCollisionFrames =
|
|
cnt[RTL8365MB_MIB_dot3StatsMultipleCollisionFrames];
|
|
mac_stats->FramesReceivedOK = cnt[RTL8365MB_MIB_ifInUcastPkts] +
|
|
cnt[RTL8365MB_MIB_ifInMulticastPkts] +
|
|
cnt[RTL8365MB_MIB_ifInBroadcastPkts] +
|
|
cnt[RTL8365MB_MIB_dot3InPauseFrames];
|
|
mac_stats->FrameCheckSequenceErrors =
|
|
cnt[RTL8365MB_MIB_dot3StatsFCSErrors];
|
|
mac_stats->OctetsTransmittedOK = cnt[RTL8365MB_MIB_ifOutOctets] -
|
|
18 * mac_stats->FramesTransmittedOK;
|
|
mac_stats->FramesWithDeferredXmissions =
|
|
cnt[RTL8365MB_MIB_dot3StatsDeferredTransmissions];
|
|
mac_stats->LateCollisions = cnt[RTL8365MB_MIB_dot3StatsLateCollisions];
|
|
mac_stats->FramesAbortedDueToXSColls =
|
|
cnt[RTL8365MB_MIB_dot3StatsExcessiveCollisions];
|
|
mac_stats->OctetsReceivedOK = cnt[RTL8365MB_MIB_ifInOctets] -
|
|
18 * mac_stats->FramesReceivedOK;
|
|
mac_stats->MulticastFramesXmittedOK =
|
|
cnt[RTL8365MB_MIB_ifOutMulticastPkts];
|
|
mac_stats->BroadcastFramesXmittedOK =
|
|
cnt[RTL8365MB_MIB_ifOutBroadcastPkts];
|
|
mac_stats->MulticastFramesReceivedOK =
|
|
cnt[RTL8365MB_MIB_ifInMulticastPkts];
|
|
mac_stats->BroadcastFramesReceivedOK =
|
|
cnt[RTL8365MB_MIB_ifInBroadcastPkts];
|
|
}
|
|
|
|
static void rtl8365mb_get_ctrl_stats(struct dsa_switch *ds, int port,
|
|
struct ethtool_eth_ctrl_stats *ctrl_stats)
|
|
{
|
|
struct realtek_priv *priv = ds->priv;
|
|
struct rtl8365mb_mib_counter *mib;
|
|
struct rtl8365mb *mb;
|
|
|
|
mb = priv->chip_data;
|
|
mib = &rtl8365mb_mib_counters[RTL8365MB_MIB_dot3ControlInUnknownOpcodes];
|
|
|
|
mutex_lock(&mb->mib_lock);
|
|
rtl8365mb_mib_counter_read(priv, port, mib->offset, mib->length,
|
|
&ctrl_stats->UnsupportedOpcodesReceived);
|
|
mutex_unlock(&mb->mib_lock);
|
|
}
|
|
|
|
static void rtl8365mb_stats_update(struct realtek_priv *priv, int port)
|
|
{
|
|
u64 cnt[RTL8365MB_MIB_END] = {
|
|
[RTL8365MB_MIB_ifOutOctets] = 1,
|
|
[RTL8365MB_MIB_ifOutUcastPkts] = 1,
|
|
[RTL8365MB_MIB_ifOutMulticastPkts] = 1,
|
|
[RTL8365MB_MIB_ifOutBroadcastPkts] = 1,
|
|
[RTL8365MB_MIB_ifOutDiscards] = 1,
|
|
[RTL8365MB_MIB_ifInOctets] = 1,
|
|
[RTL8365MB_MIB_ifInUcastPkts] = 1,
|
|
[RTL8365MB_MIB_ifInMulticastPkts] = 1,
|
|
[RTL8365MB_MIB_ifInBroadcastPkts] = 1,
|
|
[RTL8365MB_MIB_etherStatsDropEvents] = 1,
|
|
[RTL8365MB_MIB_etherStatsCollisions] = 1,
|
|
[RTL8365MB_MIB_etherStatsFragments] = 1,
|
|
[RTL8365MB_MIB_etherStatsJabbers] = 1,
|
|
[RTL8365MB_MIB_dot3StatsFCSErrors] = 1,
|
|
[RTL8365MB_MIB_dot3StatsLateCollisions] = 1,
|
|
};
|
|
struct rtl8365mb *mb = priv->chip_data;
|
|
struct rtnl_link_stats64 *stats;
|
|
int ret;
|
|
int i;
|
|
|
|
stats = &mb->ports[port].stats;
|
|
|
|
mutex_lock(&mb->mib_lock);
|
|
for (i = 0; i < RTL8365MB_MIB_END; i++) {
|
|
struct rtl8365mb_mib_counter *c = &rtl8365mb_mib_counters[i];
|
|
|
|
/* Only fetch required MIB counters (marked = 1 above) */
|
|
if (!cnt[i])
|
|
continue;
|
|
|
|
ret = rtl8365mb_mib_counter_read(priv, port, c->offset,
|
|
c->length, &cnt[i]);
|
|
if (ret)
|
|
break;
|
|
}
|
|
mutex_unlock(&mb->mib_lock);
|
|
|
|
/* Don't update statistics if there was an error reading the counters */
|
|
if (ret)
|
|
return;
|
|
|
|
spin_lock(&mb->ports[port].stats_lock);
|
|
|
|
stats->rx_packets = cnt[RTL8365MB_MIB_ifInUcastPkts] +
|
|
cnt[RTL8365MB_MIB_ifInMulticastPkts] +
|
|
cnt[RTL8365MB_MIB_ifInBroadcastPkts] -
|
|
cnt[RTL8365MB_MIB_ifOutDiscards];
|
|
|
|
stats->tx_packets = cnt[RTL8365MB_MIB_ifOutUcastPkts] +
|
|
cnt[RTL8365MB_MIB_ifOutMulticastPkts] +
|
|
cnt[RTL8365MB_MIB_ifOutBroadcastPkts];
|
|
|
|
/* if{In,Out}Octets includes FCS - remove it */
|
|
stats->rx_bytes = cnt[RTL8365MB_MIB_ifInOctets] - 4 * stats->rx_packets;
|
|
stats->tx_bytes =
|
|
cnt[RTL8365MB_MIB_ifOutOctets] - 4 * stats->tx_packets;
|
|
|
|
stats->rx_dropped = cnt[RTL8365MB_MIB_etherStatsDropEvents];
|
|
stats->tx_dropped = cnt[RTL8365MB_MIB_ifOutDiscards];
|
|
|
|
stats->multicast = cnt[RTL8365MB_MIB_ifInMulticastPkts];
|
|
stats->collisions = cnt[RTL8365MB_MIB_etherStatsCollisions];
|
|
|
|
stats->rx_length_errors = cnt[RTL8365MB_MIB_etherStatsFragments] +
|
|
cnt[RTL8365MB_MIB_etherStatsJabbers];
|
|
stats->rx_crc_errors = cnt[RTL8365MB_MIB_dot3StatsFCSErrors];
|
|
stats->rx_errors = stats->rx_length_errors + stats->rx_crc_errors;
|
|
|
|
stats->tx_aborted_errors = cnt[RTL8365MB_MIB_ifOutDiscards];
|
|
stats->tx_window_errors = cnt[RTL8365MB_MIB_dot3StatsLateCollisions];
|
|
stats->tx_errors = stats->tx_aborted_errors + stats->tx_window_errors;
|
|
|
|
spin_unlock(&mb->ports[port].stats_lock);
|
|
}
|
|
|
|
static void rtl8365mb_stats_poll(struct work_struct *work)
|
|
{
|
|
struct rtl8365mb_port *p = container_of(to_delayed_work(work),
|
|
struct rtl8365mb_port,
|
|
mib_work);
|
|
struct realtek_priv *priv = p->priv;
|
|
|
|
rtl8365mb_stats_update(priv, p->index);
|
|
|
|
schedule_delayed_work(&p->mib_work, RTL8365MB_STATS_INTERVAL_JIFFIES);
|
|
}
|
|
|
|
static void rtl8365mb_get_stats64(struct dsa_switch *ds, int port,
|
|
struct rtnl_link_stats64 *s)
|
|
{
|
|
struct realtek_priv *priv = ds->priv;
|
|
struct rtl8365mb_port *p;
|
|
struct rtl8365mb *mb;
|
|
|
|
mb = priv->chip_data;
|
|
p = &mb->ports[port];
|
|
|
|
spin_lock(&p->stats_lock);
|
|
memcpy(s, &p->stats, sizeof(*s));
|
|
spin_unlock(&p->stats_lock);
|
|
}
|
|
|
|
static void rtl8365mb_stats_setup(struct realtek_priv *priv)
|
|
{
|
|
struct rtl8365mb *mb = priv->chip_data;
|
|
int i;
|
|
|
|
/* Per-chip global mutex to protect MIB counter access, since doing
|
|
* so requires accessing a series of registers in a particular order.
|
|
*/
|
|
mutex_init(&mb->mib_lock);
|
|
|
|
for (i = 0; i < priv->num_ports; i++) {
|
|
struct rtl8365mb_port *p = &mb->ports[i];
|
|
|
|
if (dsa_is_unused_port(priv->ds, i))
|
|
continue;
|
|
|
|
/* Per-port spinlock to protect the stats64 data */
|
|
spin_lock_init(&p->stats_lock);
|
|
|
|
/* This work polls the MIB counters and keeps the stats64 data
|
|
* up-to-date.
|
|
*/
|
|
INIT_DELAYED_WORK(&p->mib_work, rtl8365mb_stats_poll);
|
|
}
|
|
}
|
|
|
|
static void rtl8365mb_stats_teardown(struct realtek_priv *priv)
|
|
{
|
|
struct rtl8365mb *mb = priv->chip_data;
|
|
int i;
|
|
|
|
for (i = 0; i < priv->num_ports; i++) {
|
|
struct rtl8365mb_port *p = &mb->ports[i];
|
|
|
|
if (dsa_is_unused_port(priv->ds, i))
|
|
continue;
|
|
|
|
cancel_delayed_work_sync(&p->mib_work);
|
|
}
|
|
}
|
|
|
|
static int rtl8365mb_get_and_clear_status_reg(struct realtek_priv *priv, u32 reg,
|
|
u32 *val)
|
|
{
|
|
int ret;
|
|
|
|
ret = regmap_read(priv->map, reg, val);
|
|
if (ret)
|
|
return ret;
|
|
|
|
return regmap_write(priv->map, reg, *val);
|
|
}
|
|
|
|
static irqreturn_t rtl8365mb_irq(int irq, void *data)
|
|
{
|
|
struct realtek_priv *priv = data;
|
|
unsigned long line_changes = 0;
|
|
u32 stat;
|
|
int line;
|
|
int ret;
|
|
|
|
ret = rtl8365mb_get_and_clear_status_reg(priv, RTL8365MB_INTR_STATUS_REG,
|
|
&stat);
|
|
if (ret)
|
|
goto out_error;
|
|
|
|
if (stat & RTL8365MB_INTR_LINK_CHANGE_MASK) {
|
|
u32 linkdown_ind;
|
|
u32 linkup_ind;
|
|
u32 val;
|
|
|
|
ret = rtl8365mb_get_and_clear_status_reg(
|
|
priv, RTL8365MB_PORT_LINKUP_IND_REG, &val);
|
|
if (ret)
|
|
goto out_error;
|
|
|
|
linkup_ind = FIELD_GET(RTL8365MB_PORT_LINKUP_IND_MASK, val);
|
|
|
|
ret = rtl8365mb_get_and_clear_status_reg(
|
|
priv, RTL8365MB_PORT_LINKDOWN_IND_REG, &val);
|
|
if (ret)
|
|
goto out_error;
|
|
|
|
linkdown_ind = FIELD_GET(RTL8365MB_PORT_LINKDOWN_IND_MASK, val);
|
|
|
|
line_changes = linkup_ind | linkdown_ind;
|
|
}
|
|
|
|
if (!line_changes)
|
|
goto out_none;
|
|
|
|
for_each_set_bit(line, &line_changes, priv->num_ports) {
|
|
int child_irq = irq_find_mapping(priv->irqdomain, line);
|
|
|
|
handle_nested_irq(child_irq);
|
|
}
|
|
|
|
return IRQ_HANDLED;
|
|
|
|
out_error:
|
|
dev_err(priv->dev, "failed to read interrupt status: %d\n", ret);
|
|
|
|
out_none:
|
|
return IRQ_NONE;
|
|
}
|
|
|
|
static struct irq_chip rtl8365mb_irq_chip = {
|
|
.name = "rtl8365mb",
|
|
/* The hardware doesn't support masking IRQs on a per-port basis */
|
|
};
|
|
|
|
static int rtl8365mb_irq_map(struct irq_domain *domain, unsigned int irq,
|
|
irq_hw_number_t hwirq)
|
|
{
|
|
irq_set_chip_data(irq, domain->host_data);
|
|
irq_set_chip_and_handler(irq, &rtl8365mb_irq_chip, handle_simple_irq);
|
|
irq_set_nested_thread(irq, 1);
|
|
irq_set_noprobe(irq);
|
|
|
|
return 0;
|
|
}
|
|
|
|
static void rtl8365mb_irq_unmap(struct irq_domain *d, unsigned int irq)
|
|
{
|
|
irq_set_nested_thread(irq, 0);
|
|
irq_set_chip_and_handler(irq, NULL, NULL);
|
|
irq_set_chip_data(irq, NULL);
|
|
}
|
|
|
|
static const struct irq_domain_ops rtl8365mb_irqdomain_ops = {
|
|
.map = rtl8365mb_irq_map,
|
|
.unmap = rtl8365mb_irq_unmap,
|
|
.xlate = irq_domain_xlate_onecell,
|
|
};
|
|
|
|
static int rtl8365mb_set_irq_enable(struct realtek_priv *priv, bool enable)
|
|
{
|
|
return regmap_update_bits(priv->map, RTL8365MB_INTR_CTRL_REG,
|
|
RTL8365MB_INTR_LINK_CHANGE_MASK,
|
|
FIELD_PREP(RTL8365MB_INTR_LINK_CHANGE_MASK,
|
|
enable ? 1 : 0));
|
|
}
|
|
|
|
static int rtl8365mb_irq_enable(struct realtek_priv *priv)
|
|
{
|
|
return rtl8365mb_set_irq_enable(priv, true);
|
|
}
|
|
|
|
static int rtl8365mb_irq_disable(struct realtek_priv *priv)
|
|
{
|
|
return rtl8365mb_set_irq_enable(priv, false);
|
|
}
|
|
|
|
static int rtl8365mb_irq_setup(struct realtek_priv *priv)
|
|
{
|
|
struct rtl8365mb *mb = priv->chip_data;
|
|
struct device_node *intc;
|
|
u32 irq_trig;
|
|
int virq;
|
|
int irq;
|
|
u32 val;
|
|
int ret;
|
|
int i;
|
|
|
|
intc = of_get_child_by_name(priv->dev->of_node, "interrupt-controller");
|
|
if (!intc) {
|
|
dev_err(priv->dev, "missing child interrupt-controller node\n");
|
|
return -EINVAL;
|
|
}
|
|
|
|
/* rtl8365mb IRQs cascade off this one */
|
|
irq = of_irq_get(intc, 0);
|
|
if (irq <= 0) {
|
|
if (irq != -EPROBE_DEFER)
|
|
dev_err(priv->dev, "failed to get parent irq: %d\n",
|
|
irq);
|
|
ret = irq ? irq : -EINVAL;
|
|
goto out_put_node;
|
|
}
|
|
|
|
priv->irqdomain = irq_domain_add_linear(intc, priv->num_ports,
|
|
&rtl8365mb_irqdomain_ops, priv);
|
|
if (!priv->irqdomain) {
|
|
dev_err(priv->dev, "failed to add irq domain\n");
|
|
ret = -ENOMEM;
|
|
goto out_put_node;
|
|
}
|
|
|
|
for (i = 0; i < priv->num_ports; i++) {
|
|
virq = irq_create_mapping(priv->irqdomain, i);
|
|
if (!virq) {
|
|
dev_err(priv->dev,
|
|
"failed to create irq domain mapping\n");
|
|
ret = -EINVAL;
|
|
goto out_remove_irqdomain;
|
|
}
|
|
|
|
irq_set_parent(virq, irq);
|
|
}
|
|
|
|
/* Configure chip interrupt signal polarity */
|
|
irq_trig = irqd_get_trigger_type(irq_get_irq_data(irq));
|
|
switch (irq_trig) {
|
|
case IRQF_TRIGGER_RISING:
|
|
case IRQF_TRIGGER_HIGH:
|
|
val = RTL8365MB_INTR_POLARITY_HIGH;
|
|
break;
|
|
case IRQF_TRIGGER_FALLING:
|
|
case IRQF_TRIGGER_LOW:
|
|
val = RTL8365MB_INTR_POLARITY_LOW;
|
|
break;
|
|
default:
|
|
dev_err(priv->dev, "unsupported irq trigger type %u\n",
|
|
irq_trig);
|
|
ret = -EINVAL;
|
|
goto out_remove_irqdomain;
|
|
}
|
|
|
|
ret = regmap_update_bits(priv->map, RTL8365MB_INTR_POLARITY_REG,
|
|
RTL8365MB_INTR_POLARITY_MASK,
|
|
FIELD_PREP(RTL8365MB_INTR_POLARITY_MASK, val));
|
|
if (ret)
|
|
goto out_remove_irqdomain;
|
|
|
|
/* Disable the interrupt in case the chip has it enabled on reset */
|
|
ret = rtl8365mb_irq_disable(priv);
|
|
if (ret)
|
|
goto out_remove_irqdomain;
|
|
|
|
/* Clear the interrupt status register */
|
|
ret = regmap_write(priv->map, RTL8365MB_INTR_STATUS_REG,
|
|
RTL8365MB_INTR_ALL_MASK);
|
|
if (ret)
|
|
goto out_remove_irqdomain;
|
|
|
|
ret = request_threaded_irq(irq, NULL, rtl8365mb_irq, IRQF_ONESHOT,
|
|
"rtl8365mb", priv);
|
|
if (ret) {
|
|
dev_err(priv->dev, "failed to request irq: %d\n", ret);
|
|
goto out_remove_irqdomain;
|
|
}
|
|
|
|
/* Store the irq so that we know to free it during teardown */
|
|
mb->irq = irq;
|
|
|
|
ret = rtl8365mb_irq_enable(priv);
|
|
if (ret)
|
|
goto out_free_irq;
|
|
|
|
of_node_put(intc);
|
|
|
|
return 0;
|
|
|
|
out_free_irq:
|
|
free_irq(mb->irq, priv);
|
|
mb->irq = 0;
|
|
|
|
out_remove_irqdomain:
|
|
for (i = 0; i < priv->num_ports; i++) {
|
|
virq = irq_find_mapping(priv->irqdomain, i);
|
|
irq_dispose_mapping(virq);
|
|
}
|
|
|
|
irq_domain_remove(priv->irqdomain);
|
|
priv->irqdomain = NULL;
|
|
|
|
out_put_node:
|
|
of_node_put(intc);
|
|
|
|
return ret;
|
|
}
|
|
|
|
static void rtl8365mb_irq_teardown(struct realtek_priv *priv)
|
|
{
|
|
struct rtl8365mb *mb = priv->chip_data;
|
|
int virq;
|
|
int i;
|
|
|
|
if (mb->irq) {
|
|
free_irq(mb->irq, priv);
|
|
mb->irq = 0;
|
|
}
|
|
|
|
if (priv->irqdomain) {
|
|
for (i = 0; i < priv->num_ports; i++) {
|
|
virq = irq_find_mapping(priv->irqdomain, i);
|
|
irq_dispose_mapping(virq);
|
|
}
|
|
|
|
irq_domain_remove(priv->irqdomain);
|
|
priv->irqdomain = NULL;
|
|
}
|
|
}
|
|
|
|
static int rtl8365mb_cpu_config(struct realtek_priv *priv)
|
|
{
|
|
struct rtl8365mb *mb = priv->chip_data;
|
|
struct rtl8365mb_cpu *cpu = &mb->cpu;
|
|
u32 val;
|
|
int ret;
|
|
|
|
ret = regmap_update_bits(priv->map, RTL8365MB_CPU_PORT_MASK_REG,
|
|
RTL8365MB_CPU_PORT_MASK_MASK,
|
|
FIELD_PREP(RTL8365MB_CPU_PORT_MASK_MASK,
|
|
cpu->mask));
|
|
if (ret)
|
|
return ret;
|
|
|
|
val = FIELD_PREP(RTL8365MB_CPU_CTRL_EN_MASK, cpu->enable ? 1 : 0) |
|
|
FIELD_PREP(RTL8365MB_CPU_CTRL_INSERTMODE_MASK, cpu->insert) |
|
|
FIELD_PREP(RTL8365MB_CPU_CTRL_TAG_POSITION_MASK, cpu->position) |
|
|
FIELD_PREP(RTL8365MB_CPU_CTRL_RXBYTECOUNT_MASK, cpu->rx_length) |
|
|
FIELD_PREP(RTL8365MB_CPU_CTRL_TAG_FORMAT_MASK, cpu->format) |
|
|
FIELD_PREP(RTL8365MB_CPU_CTRL_TRAP_PORT_MASK, cpu->trap_port & 0x7) |
|
|
FIELD_PREP(RTL8365MB_CPU_CTRL_TRAP_PORT_EXT_MASK,
|
|
cpu->trap_port >> 3 & 0x1);
|
|
ret = regmap_write(priv->map, RTL8365MB_CPU_CTRL_REG, val);
|
|
if (ret)
|
|
return ret;
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int rtl8365mb_change_tag_protocol(struct dsa_switch *ds,
|
|
enum dsa_tag_protocol proto)
|
|
{
|
|
struct realtek_priv *priv = ds->priv;
|
|
struct rtl8365mb_cpu *cpu;
|
|
struct rtl8365mb *mb;
|
|
|
|
mb = priv->chip_data;
|
|
cpu = &mb->cpu;
|
|
|
|
switch (proto) {
|
|
case DSA_TAG_PROTO_RTL8_4:
|
|
cpu->format = RTL8365MB_CPU_FORMAT_8BYTES;
|
|
cpu->position = RTL8365MB_CPU_POS_AFTER_SA;
|
|
break;
|
|
case DSA_TAG_PROTO_RTL8_4T:
|
|
cpu->format = RTL8365MB_CPU_FORMAT_8BYTES;
|
|
cpu->position = RTL8365MB_CPU_POS_BEFORE_CRC;
|
|
break;
|
|
/* The switch also supports a 4-byte format, similar to rtl4a but with
|
|
* the same 0x04 8-bit version and probably 8-bit port source/dest.
|
|
* There is no public doc about it. Not supported yet and it will probably
|
|
* never be.
|
|
*/
|
|
default:
|
|
return -EPROTONOSUPPORT;
|
|
}
|
|
|
|
return rtl8365mb_cpu_config(priv);
|
|
}
|
|
|
|
static int rtl8365mb_switch_init(struct realtek_priv *priv)
|
|
{
|
|
struct rtl8365mb *mb = priv->chip_data;
|
|
const struct rtl8365mb_chip_info *ci;
|
|
int ret;
|
|
int i;
|
|
|
|
ci = mb->chip_info;
|
|
|
|
/* Do any chip-specific init jam before getting to the common stuff */
|
|
if (ci->jam_table) {
|
|
for (i = 0; i < ci->jam_size; i++) {
|
|
ret = regmap_write(priv->map, ci->jam_table[i].reg,
|
|
ci->jam_table[i].val);
|
|
if (ret)
|
|
return ret;
|
|
}
|
|
}
|
|
|
|
/* Common init jam */
|
|
for (i = 0; i < ARRAY_SIZE(rtl8365mb_init_jam_common); i++) {
|
|
ret = regmap_write(priv->map, rtl8365mb_init_jam_common[i].reg,
|
|
rtl8365mb_init_jam_common[i].val);
|
|
if (ret)
|
|
return ret;
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int rtl8365mb_reset_chip(struct realtek_priv *priv)
|
|
{
|
|
u32 val;
|
|
|
|
priv->write_reg_noack(priv, RTL8365MB_CHIP_RESET_REG,
|
|
FIELD_PREP(RTL8365MB_CHIP_RESET_HW_MASK, 1));
|
|
|
|
/* Realtek documentation says the chip needs 1 second to reset. Sleep
|
|
* for 100 ms before accessing any registers to prevent ACK timeouts.
|
|
*/
|
|
msleep(100);
|
|
return regmap_read_poll_timeout(priv->map, RTL8365MB_CHIP_RESET_REG, val,
|
|
!(val & RTL8365MB_CHIP_RESET_HW_MASK),
|
|
20000, 1e6);
|
|
}
|
|
|
|
static int rtl8365mb_setup(struct dsa_switch *ds)
|
|
{
|
|
struct realtek_priv *priv = ds->priv;
|
|
struct rtl8365mb_cpu *cpu;
|
|
struct dsa_port *cpu_dp;
|
|
struct rtl8365mb *mb;
|
|
int ret;
|
|
int i;
|
|
|
|
mb = priv->chip_data;
|
|
cpu = &mb->cpu;
|
|
|
|
ret = rtl8365mb_reset_chip(priv);
|
|
if (ret) {
|
|
dev_err(priv->dev, "failed to reset chip: %d\n", ret);
|
|
goto out_error;
|
|
}
|
|
|
|
/* Configure switch to vendor-defined initial state */
|
|
ret = rtl8365mb_switch_init(priv);
|
|
if (ret) {
|
|
dev_err(priv->dev, "failed to initialize switch: %d\n", ret);
|
|
goto out_error;
|
|
}
|
|
|
|
/* Set up cascading IRQs */
|
|
ret = rtl8365mb_irq_setup(priv);
|
|
if (ret == -EPROBE_DEFER)
|
|
return ret;
|
|
else if (ret)
|
|
dev_info(priv->dev, "no interrupt support\n");
|
|
|
|
/* Configure CPU tagging */
|
|
dsa_switch_for_each_cpu_port(cpu_dp, priv->ds) {
|
|
cpu->mask |= BIT(cpu_dp->index);
|
|
|
|
if (cpu->trap_port == RTL8365MB_MAX_NUM_PORTS)
|
|
cpu->trap_port = cpu_dp->index;
|
|
}
|
|
cpu->enable = cpu->mask > 0;
|
|
ret = rtl8365mb_cpu_config(priv);
|
|
if (ret)
|
|
goto out_teardown_irq;
|
|
|
|
/* Configure ports */
|
|
for (i = 0; i < priv->num_ports; i++) {
|
|
struct rtl8365mb_port *p = &mb->ports[i];
|
|
|
|
if (dsa_is_unused_port(priv->ds, i))
|
|
continue;
|
|
|
|
/* Forward only to the CPU */
|
|
ret = rtl8365mb_port_set_isolation(priv, i, cpu->mask);
|
|
if (ret)
|
|
goto out_teardown_irq;
|
|
|
|
/* Disable learning */
|
|
ret = rtl8365mb_port_set_learning(priv, i, false);
|
|
if (ret)
|
|
goto out_teardown_irq;
|
|
|
|
/* Set the initial STP state of all ports to DISABLED, otherwise
|
|
* ports will still forward frames to the CPU despite being
|
|
* administratively down by default.
|
|
*/
|
|
rtl8365mb_port_stp_state_set(priv->ds, i, BR_STATE_DISABLED);
|
|
|
|
/* Set up per-port private data */
|
|
p->priv = priv;
|
|
p->index = i;
|
|
}
|
|
|
|
/* Set maximum packet length to 1536 bytes */
|
|
ret = regmap_update_bits(priv->map, RTL8365MB_CFG0_MAX_LEN_REG,
|
|
RTL8365MB_CFG0_MAX_LEN_MASK,
|
|
FIELD_PREP(RTL8365MB_CFG0_MAX_LEN_MASK, 1536));
|
|
if (ret)
|
|
goto out_teardown_irq;
|
|
|
|
if (priv->setup_interface) {
|
|
ret = priv->setup_interface(ds);
|
|
if (ret) {
|
|
dev_err(priv->dev, "could not set up MDIO bus\n");
|
|
goto out_teardown_irq;
|
|
}
|
|
}
|
|
|
|
/* Start statistics counter polling */
|
|
rtl8365mb_stats_setup(priv);
|
|
|
|
return 0;
|
|
|
|
out_teardown_irq:
|
|
rtl8365mb_irq_teardown(priv);
|
|
|
|
out_error:
|
|
return ret;
|
|
}
|
|
|
|
static void rtl8365mb_teardown(struct dsa_switch *ds)
|
|
{
|
|
struct realtek_priv *priv = ds->priv;
|
|
|
|
rtl8365mb_stats_teardown(priv);
|
|
rtl8365mb_irq_teardown(priv);
|
|
}
|
|
|
|
static int rtl8365mb_get_chip_id_and_ver(struct regmap *map, u32 *id, u32 *ver)
|
|
{
|
|
int ret;
|
|
|
|
/* For some reason we have to write a magic value to an arbitrary
|
|
* register whenever accessing the chip ID/version registers.
|
|
*/
|
|
ret = regmap_write(map, RTL8365MB_MAGIC_REG, RTL8365MB_MAGIC_VALUE);
|
|
if (ret)
|
|
return ret;
|
|
|
|
ret = regmap_read(map, RTL8365MB_CHIP_ID_REG, id);
|
|
if (ret)
|
|
return ret;
|
|
|
|
ret = regmap_read(map, RTL8365MB_CHIP_VER_REG, ver);
|
|
if (ret)
|
|
return ret;
|
|
|
|
/* Reset magic register */
|
|
ret = regmap_write(map, RTL8365MB_MAGIC_REG, 0);
|
|
if (ret)
|
|
return ret;
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int rtl8365mb_detect(struct realtek_priv *priv)
|
|
{
|
|
struct rtl8365mb *mb = priv->chip_data;
|
|
u32 chip_id;
|
|
u32 chip_ver;
|
|
int ret;
|
|
int i;
|
|
|
|
ret = rtl8365mb_get_chip_id_and_ver(priv->map, &chip_id, &chip_ver);
|
|
if (ret) {
|
|
dev_err(priv->dev, "failed to read chip id and version: %d\n",
|
|
ret);
|
|
return ret;
|
|
}
|
|
|
|
for (i = 0; i < ARRAY_SIZE(rtl8365mb_chip_infos); i++) {
|
|
const struct rtl8365mb_chip_info *ci = &rtl8365mb_chip_infos[i];
|
|
|
|
if (ci->chip_id == chip_id && ci->chip_ver == chip_ver) {
|
|
mb->chip_info = ci;
|
|
break;
|
|
}
|
|
}
|
|
|
|
if (!mb->chip_info) {
|
|
dev_err(priv->dev,
|
|
"unrecognized switch (id=0x%04x, ver=0x%04x)", chip_id,
|
|
chip_ver);
|
|
return -ENODEV;
|
|
}
|
|
|
|
dev_info(priv->dev, "found an %s switch\n", mb->chip_info->name);
|
|
|
|
priv->num_ports = RTL8365MB_MAX_NUM_PORTS;
|
|
mb->priv = priv;
|
|
mb->cpu.trap_port = RTL8365MB_MAX_NUM_PORTS;
|
|
mb->cpu.insert = RTL8365MB_CPU_INSERT_TO_ALL;
|
|
mb->cpu.position = RTL8365MB_CPU_POS_AFTER_SA;
|
|
mb->cpu.rx_length = RTL8365MB_CPU_RXLEN_64BYTES;
|
|
mb->cpu.format = RTL8365MB_CPU_FORMAT_8BYTES;
|
|
|
|
return 0;
|
|
}
|
|
|
|
static const struct dsa_switch_ops rtl8365mb_switch_ops_smi = {
|
|
.get_tag_protocol = rtl8365mb_get_tag_protocol,
|
|
.change_tag_protocol = rtl8365mb_change_tag_protocol,
|
|
.setup = rtl8365mb_setup,
|
|
.teardown = rtl8365mb_teardown,
|
|
.phylink_get_caps = rtl8365mb_phylink_get_caps,
|
|
.phylink_mac_config = rtl8365mb_phylink_mac_config,
|
|
.phylink_mac_link_down = rtl8365mb_phylink_mac_link_down,
|
|
.phylink_mac_link_up = rtl8365mb_phylink_mac_link_up,
|
|
.port_stp_state_set = rtl8365mb_port_stp_state_set,
|
|
.get_strings = rtl8365mb_get_strings,
|
|
.get_ethtool_stats = rtl8365mb_get_ethtool_stats,
|
|
.get_sset_count = rtl8365mb_get_sset_count,
|
|
.get_eth_phy_stats = rtl8365mb_get_phy_stats,
|
|
.get_eth_mac_stats = rtl8365mb_get_mac_stats,
|
|
.get_eth_ctrl_stats = rtl8365mb_get_ctrl_stats,
|
|
.get_stats64 = rtl8365mb_get_stats64,
|
|
};
|
|
|
|
static const struct dsa_switch_ops rtl8365mb_switch_ops_mdio = {
|
|
.get_tag_protocol = rtl8365mb_get_tag_protocol,
|
|
.change_tag_protocol = rtl8365mb_change_tag_protocol,
|
|
.setup = rtl8365mb_setup,
|
|
.teardown = rtl8365mb_teardown,
|
|
.phylink_get_caps = rtl8365mb_phylink_get_caps,
|
|
.phylink_mac_config = rtl8365mb_phylink_mac_config,
|
|
.phylink_mac_link_down = rtl8365mb_phylink_mac_link_down,
|
|
.phylink_mac_link_up = rtl8365mb_phylink_mac_link_up,
|
|
.phy_read = rtl8365mb_dsa_phy_read,
|
|
.phy_write = rtl8365mb_dsa_phy_write,
|
|
.port_stp_state_set = rtl8365mb_port_stp_state_set,
|
|
.get_strings = rtl8365mb_get_strings,
|
|
.get_ethtool_stats = rtl8365mb_get_ethtool_stats,
|
|
.get_sset_count = rtl8365mb_get_sset_count,
|
|
.get_eth_phy_stats = rtl8365mb_get_phy_stats,
|
|
.get_eth_mac_stats = rtl8365mb_get_mac_stats,
|
|
.get_eth_ctrl_stats = rtl8365mb_get_ctrl_stats,
|
|
.get_stats64 = rtl8365mb_get_stats64,
|
|
};
|
|
|
|
static const struct realtek_ops rtl8365mb_ops = {
|
|
.detect = rtl8365mb_detect,
|
|
.phy_read = rtl8365mb_phy_read,
|
|
.phy_write = rtl8365mb_phy_write,
|
|
};
|
|
|
|
const struct realtek_variant rtl8365mb_variant = {
|
|
.ds_ops_smi = &rtl8365mb_switch_ops_smi,
|
|
.ds_ops_mdio = &rtl8365mb_switch_ops_mdio,
|
|
.ops = &rtl8365mb_ops,
|
|
.clk_delay = 10,
|
|
.cmd_read = 0xb9,
|
|
.cmd_write = 0xb8,
|
|
.chip_data_sz = sizeof(struct rtl8365mb),
|
|
};
|
|
EXPORT_SYMBOL_GPL(rtl8365mb_variant);
|
|
|
|
MODULE_AUTHOR("Alvin Šipraga <alsi@bang-olufsen.dk>");
|
|
MODULE_DESCRIPTION("Driver for RTL8365MB-VC ethernet switch");
|
|
MODULE_LICENSE("GPL");
|