2723 lines
76 KiB
C
2723 lines
76 KiB
C
// SPDX-License-Identifier: GPL-2.0-only
|
|
/*
|
|
* Copyright (C) 1999 - 2010 Intel Corporation.
|
|
* Copyright (C) 2010 - 2012 LAPIS SEMICONDUCTOR CO., LTD.
|
|
*
|
|
* This code was derived from the Intel e1000e Linux driver.
|
|
*/
|
|
|
|
#include "pch_gbe.h"
|
|
#include "pch_gbe_phy.h"
|
|
|
|
#include <linux/gpio/consumer.h>
|
|
#include <linux/gpio/machine.h>
|
|
#include <linux/iopoll.h>
|
|
#include <linux/module.h>
|
|
#include <linux/net_tstamp.h>
|
|
#include <linux/ptp_classify.h>
|
|
#include <linux/ptp_pch.h>
|
|
#include <linux/gpio.h>
|
|
|
|
#define PCH_GBE_MAR_ENTRIES 16
|
|
#define PCH_GBE_SHORT_PKT 64
|
|
#define DSC_INIT16 0xC000
|
|
#define PCH_GBE_DMA_ALIGN 0
|
|
#define PCH_GBE_DMA_PADDING 2
|
|
#define PCH_GBE_WATCHDOG_PERIOD (5 * HZ) /* watchdog time */
|
|
#define PCH_GBE_PCI_BAR 1
|
|
#define PCH_GBE_RESERVE_MEMORY 0x200000 /* 2MB */
|
|
|
|
#define PCI_DEVICE_ID_INTEL_IOH1_GBE 0x8802
|
|
|
|
#define PCI_DEVICE_ID_ROHM_ML7223_GBE 0x8013
|
|
#define PCI_DEVICE_ID_ROHM_ML7831_GBE 0x8802
|
|
|
|
#define PCH_GBE_RX_BUFFER_WRITE 16
|
|
|
|
/* Initialize the wake-on-LAN settings */
|
|
#define PCH_GBE_WL_INIT_SETTING (PCH_GBE_WLC_MP)
|
|
|
|
#define PCH_GBE_MAC_RGMII_CTRL_SETTING ( \
|
|
PCH_GBE_CHIP_TYPE_INTERNAL | \
|
|
PCH_GBE_RGMII_MODE_RGMII \
|
|
)
|
|
|
|
/* Ethertype field values */
|
|
#define PCH_GBE_MAX_RX_BUFFER_SIZE 0x2880
|
|
#define PCH_GBE_MAX_JUMBO_FRAME_SIZE 10318
|
|
#define PCH_GBE_FRAME_SIZE_2048 2048
|
|
#define PCH_GBE_FRAME_SIZE_4096 4096
|
|
#define PCH_GBE_FRAME_SIZE_8192 8192
|
|
|
|
#define PCH_GBE_GET_DESC(R, i, type) (&(((struct type *)((R).desc))[i]))
|
|
#define PCH_GBE_RX_DESC(R, i) PCH_GBE_GET_DESC(R, i, pch_gbe_rx_desc)
|
|
#define PCH_GBE_TX_DESC(R, i) PCH_GBE_GET_DESC(R, i, pch_gbe_tx_desc)
|
|
#define PCH_GBE_DESC_UNUSED(R) \
|
|
((((R)->next_to_clean > (R)->next_to_use) ? 0 : (R)->count) + \
|
|
(R)->next_to_clean - (R)->next_to_use - 1)
|
|
|
|
/* Pause packet value */
|
|
#define PCH_GBE_PAUSE_PKT1_VALUE 0x00C28001
|
|
#define PCH_GBE_PAUSE_PKT2_VALUE 0x00000100
|
|
#define PCH_GBE_PAUSE_PKT4_VALUE 0x01000888
|
|
#define PCH_GBE_PAUSE_PKT5_VALUE 0x0000FFFF
|
|
|
|
|
|
/* This defines the bits that are set in the Interrupt Mask
|
|
* Set/Read Register. Each bit is documented below:
|
|
* o RXT0 = Receiver Timer Interrupt (ring 0)
|
|
* o TXDW = Transmit Descriptor Written Back
|
|
* o RXDMT0 = Receive Descriptor Minimum Threshold hit (ring 0)
|
|
* o RXSEQ = Receive Sequence Error
|
|
* o LSC = Link Status Change
|
|
*/
|
|
#define PCH_GBE_INT_ENABLE_MASK ( \
|
|
PCH_GBE_INT_RX_DMA_CMPLT | \
|
|
PCH_GBE_INT_RX_DSC_EMP | \
|
|
PCH_GBE_INT_RX_FIFO_ERR | \
|
|
PCH_GBE_INT_WOL_DET | \
|
|
PCH_GBE_INT_TX_CMPLT \
|
|
)
|
|
|
|
#define PCH_GBE_INT_DISABLE_ALL 0
|
|
|
|
/* Macros for ieee1588 */
|
|
/* 0x40 Time Synchronization Channel Control Register Bits */
|
|
#define MASTER_MODE (1<<0)
|
|
#define SLAVE_MODE (0)
|
|
#define V2_MODE (1<<31)
|
|
#define CAP_MODE0 (0)
|
|
#define CAP_MODE2 (1<<17)
|
|
|
|
/* 0x44 Time Synchronization Channel Event Register Bits */
|
|
#define TX_SNAPSHOT_LOCKED (1<<0)
|
|
#define RX_SNAPSHOT_LOCKED (1<<1)
|
|
|
|
#define PTP_L4_MULTICAST_SA "01:00:5e:00:01:81"
|
|
#define PTP_L2_MULTICAST_SA "01:1b:19:00:00:00"
|
|
|
|
static int pch_gbe_mdio_read(struct net_device *netdev, int addr, int reg);
|
|
static void pch_gbe_mdio_write(struct net_device *netdev, int addr, int reg,
|
|
int data);
|
|
static void pch_gbe_set_multi(struct net_device *netdev);
|
|
|
|
static int pch_ptp_match(struct sk_buff *skb, u16 uid_hi, u32 uid_lo, u16 seqid)
|
|
{
|
|
u8 *data = skb->data;
|
|
unsigned int offset;
|
|
u16 hi, id;
|
|
u32 lo;
|
|
|
|
if (ptp_classify_raw(skb) == PTP_CLASS_NONE)
|
|
return 0;
|
|
|
|
offset = ETH_HLEN + IPV4_HLEN(data) + UDP_HLEN;
|
|
|
|
if (skb->len < offset + OFF_PTP_SEQUENCE_ID + sizeof(seqid))
|
|
return 0;
|
|
|
|
hi = get_unaligned_be16(data + offset + OFF_PTP_SOURCE_UUID + 0);
|
|
lo = get_unaligned_be32(data + offset + OFF_PTP_SOURCE_UUID + 2);
|
|
id = get_unaligned_be16(data + offset + OFF_PTP_SEQUENCE_ID);
|
|
|
|
return (uid_hi == hi && uid_lo == lo && seqid == id);
|
|
}
|
|
|
|
static void
|
|
pch_rx_timestamp(struct pch_gbe_adapter *adapter, struct sk_buff *skb)
|
|
{
|
|
struct skb_shared_hwtstamps *shhwtstamps;
|
|
struct pci_dev *pdev;
|
|
u64 ns;
|
|
u32 hi, lo, val;
|
|
|
|
if (!adapter->hwts_rx_en)
|
|
return;
|
|
|
|
/* Get ieee1588's dev information */
|
|
pdev = adapter->ptp_pdev;
|
|
|
|
val = pch_ch_event_read(pdev);
|
|
|
|
if (!(val & RX_SNAPSHOT_LOCKED))
|
|
return;
|
|
|
|
lo = pch_src_uuid_lo_read(pdev);
|
|
hi = pch_src_uuid_hi_read(pdev);
|
|
|
|
if (!pch_ptp_match(skb, hi, lo, hi >> 16))
|
|
goto out;
|
|
|
|
ns = pch_rx_snap_read(pdev);
|
|
|
|
shhwtstamps = skb_hwtstamps(skb);
|
|
memset(shhwtstamps, 0, sizeof(*shhwtstamps));
|
|
shhwtstamps->hwtstamp = ns_to_ktime(ns);
|
|
out:
|
|
pch_ch_event_write(pdev, RX_SNAPSHOT_LOCKED);
|
|
}
|
|
|
|
static void
|
|
pch_tx_timestamp(struct pch_gbe_adapter *adapter, struct sk_buff *skb)
|
|
{
|
|
struct skb_shared_hwtstamps shhwtstamps;
|
|
struct pci_dev *pdev;
|
|
struct skb_shared_info *shtx;
|
|
u64 ns;
|
|
u32 cnt, val;
|
|
|
|
shtx = skb_shinfo(skb);
|
|
if (likely(!(shtx->tx_flags & SKBTX_HW_TSTAMP && adapter->hwts_tx_en)))
|
|
return;
|
|
|
|
shtx->tx_flags |= SKBTX_IN_PROGRESS;
|
|
|
|
/* Get ieee1588's dev information */
|
|
pdev = adapter->ptp_pdev;
|
|
|
|
/*
|
|
* This really stinks, but we have to poll for the Tx time stamp.
|
|
*/
|
|
for (cnt = 0; cnt < 100; cnt++) {
|
|
val = pch_ch_event_read(pdev);
|
|
if (val & TX_SNAPSHOT_LOCKED)
|
|
break;
|
|
udelay(1);
|
|
}
|
|
if (!(val & TX_SNAPSHOT_LOCKED)) {
|
|
shtx->tx_flags &= ~SKBTX_IN_PROGRESS;
|
|
return;
|
|
}
|
|
|
|
ns = pch_tx_snap_read(pdev);
|
|
|
|
memset(&shhwtstamps, 0, sizeof(shhwtstamps));
|
|
shhwtstamps.hwtstamp = ns_to_ktime(ns);
|
|
skb_tstamp_tx(skb, &shhwtstamps);
|
|
|
|
pch_ch_event_write(pdev, TX_SNAPSHOT_LOCKED);
|
|
}
|
|
|
|
static int hwtstamp_ioctl(struct net_device *netdev, struct ifreq *ifr, int cmd)
|
|
{
|
|
struct hwtstamp_config cfg;
|
|
struct pch_gbe_adapter *adapter = netdev_priv(netdev);
|
|
struct pci_dev *pdev;
|
|
u8 station[20];
|
|
|
|
if (copy_from_user(&cfg, ifr->ifr_data, sizeof(cfg)))
|
|
return -EFAULT;
|
|
|
|
/* Get ieee1588's dev information */
|
|
pdev = adapter->ptp_pdev;
|
|
|
|
if (cfg.tx_type != HWTSTAMP_TX_OFF && cfg.tx_type != HWTSTAMP_TX_ON)
|
|
return -ERANGE;
|
|
|
|
switch (cfg.rx_filter) {
|
|
case HWTSTAMP_FILTER_NONE:
|
|
adapter->hwts_rx_en = 0;
|
|
break;
|
|
case HWTSTAMP_FILTER_PTP_V1_L4_SYNC:
|
|
adapter->hwts_rx_en = 0;
|
|
pch_ch_control_write(pdev, SLAVE_MODE | CAP_MODE0);
|
|
break;
|
|
case HWTSTAMP_FILTER_PTP_V1_L4_DELAY_REQ:
|
|
adapter->hwts_rx_en = 1;
|
|
pch_ch_control_write(pdev, MASTER_MODE | CAP_MODE0);
|
|
break;
|
|
case HWTSTAMP_FILTER_PTP_V2_L4_EVENT:
|
|
adapter->hwts_rx_en = 1;
|
|
pch_ch_control_write(pdev, V2_MODE | CAP_MODE2);
|
|
strcpy(station, PTP_L4_MULTICAST_SA);
|
|
pch_set_station_address(station, pdev);
|
|
break;
|
|
case HWTSTAMP_FILTER_PTP_V2_L2_EVENT:
|
|
adapter->hwts_rx_en = 1;
|
|
pch_ch_control_write(pdev, V2_MODE | CAP_MODE2);
|
|
strcpy(station, PTP_L2_MULTICAST_SA);
|
|
pch_set_station_address(station, pdev);
|
|
break;
|
|
default:
|
|
return -ERANGE;
|
|
}
|
|
|
|
adapter->hwts_tx_en = cfg.tx_type == HWTSTAMP_TX_ON;
|
|
|
|
/* Clear out any old time stamps. */
|
|
pch_ch_event_write(pdev, TX_SNAPSHOT_LOCKED | RX_SNAPSHOT_LOCKED);
|
|
|
|
return copy_to_user(ifr->ifr_data, &cfg, sizeof(cfg)) ? -EFAULT : 0;
|
|
}
|
|
|
|
static inline void pch_gbe_mac_load_mac_addr(struct pch_gbe_hw *hw)
|
|
{
|
|
iowrite32(0x01, &hw->reg->MAC_ADDR_LOAD);
|
|
}
|
|
|
|
/**
|
|
* pch_gbe_mac_read_mac_addr - Read MAC address
|
|
* @hw: Pointer to the HW structure
|
|
* Returns:
|
|
* 0: Successful.
|
|
*/
|
|
static s32 pch_gbe_mac_read_mac_addr(struct pch_gbe_hw *hw)
|
|
{
|
|
struct pch_gbe_adapter *adapter = pch_gbe_hw_to_adapter(hw);
|
|
u32 adr1a, adr1b;
|
|
|
|
adr1a = ioread32(&hw->reg->mac_adr[0].high);
|
|
adr1b = ioread32(&hw->reg->mac_adr[0].low);
|
|
|
|
hw->mac.addr[0] = (u8)(adr1a & 0xFF);
|
|
hw->mac.addr[1] = (u8)((adr1a >> 8) & 0xFF);
|
|
hw->mac.addr[2] = (u8)((adr1a >> 16) & 0xFF);
|
|
hw->mac.addr[3] = (u8)((adr1a >> 24) & 0xFF);
|
|
hw->mac.addr[4] = (u8)(adr1b & 0xFF);
|
|
hw->mac.addr[5] = (u8)((adr1b >> 8) & 0xFF);
|
|
|
|
netdev_dbg(adapter->netdev, "hw->mac.addr : %pM\n", hw->mac.addr);
|
|
return 0;
|
|
}
|
|
|
|
/**
|
|
* pch_gbe_wait_clr_bit - Wait to clear a bit
|
|
* @reg: Pointer of register
|
|
* @bit: Busy bit
|
|
*/
|
|
static void pch_gbe_wait_clr_bit(void __iomem *reg, u32 bit)
|
|
{
|
|
u32 tmp;
|
|
|
|
/* wait busy */
|
|
if (readx_poll_timeout_atomic(ioread32, reg, tmp, !(tmp & bit), 0, 10))
|
|
pr_err("Error: busy bit is not cleared\n");
|
|
}
|
|
|
|
/**
|
|
* pch_gbe_mac_mar_set - Set MAC address register
|
|
* @hw: Pointer to the HW structure
|
|
* @addr: Pointer to the MAC address
|
|
* @index: MAC address array register
|
|
*/
|
|
static void pch_gbe_mac_mar_set(struct pch_gbe_hw *hw, u8 * addr, u32 index)
|
|
{
|
|
struct pch_gbe_adapter *adapter = pch_gbe_hw_to_adapter(hw);
|
|
u32 mar_low, mar_high, adrmask;
|
|
|
|
netdev_dbg(adapter->netdev, "index : 0x%x\n", index);
|
|
|
|
/*
|
|
* HW expects these in little endian so we reverse the byte order
|
|
* from network order (big endian) to little endian
|
|
*/
|
|
mar_high = ((u32) addr[0] | ((u32) addr[1] << 8) |
|
|
((u32) addr[2] << 16) | ((u32) addr[3] << 24));
|
|
mar_low = ((u32) addr[4] | ((u32) addr[5] << 8));
|
|
/* Stop the MAC Address of index. */
|
|
adrmask = ioread32(&hw->reg->ADDR_MASK);
|
|
iowrite32((adrmask | (0x0001 << index)), &hw->reg->ADDR_MASK);
|
|
/* wait busy */
|
|
pch_gbe_wait_clr_bit(&hw->reg->ADDR_MASK, PCH_GBE_BUSY);
|
|
/* Set the MAC address to the MAC address 1A/1B register */
|
|
iowrite32(mar_high, &hw->reg->mac_adr[index].high);
|
|
iowrite32(mar_low, &hw->reg->mac_adr[index].low);
|
|
/* Start the MAC address of index */
|
|
iowrite32((adrmask & ~(0x0001 << index)), &hw->reg->ADDR_MASK);
|
|
/* wait busy */
|
|
pch_gbe_wait_clr_bit(&hw->reg->ADDR_MASK, PCH_GBE_BUSY);
|
|
}
|
|
|
|
/**
|
|
* pch_gbe_mac_reset_hw - Reset hardware
|
|
* @hw: Pointer to the HW structure
|
|
*/
|
|
static void pch_gbe_mac_reset_hw(struct pch_gbe_hw *hw)
|
|
{
|
|
/* Read the MAC address. and store to the private data */
|
|
pch_gbe_mac_read_mac_addr(hw);
|
|
iowrite32(PCH_GBE_ALL_RST, &hw->reg->RESET);
|
|
iowrite32(PCH_GBE_MODE_GMII_ETHER, &hw->reg->MODE);
|
|
pch_gbe_wait_clr_bit(&hw->reg->RESET, PCH_GBE_ALL_RST);
|
|
/* Setup the receive addresses */
|
|
pch_gbe_mac_mar_set(hw, hw->mac.addr, 0);
|
|
return;
|
|
}
|
|
|
|
static void pch_gbe_disable_mac_rx(struct pch_gbe_hw *hw)
|
|
{
|
|
u32 rctl;
|
|
/* Disables Receive MAC */
|
|
rctl = ioread32(&hw->reg->MAC_RX_EN);
|
|
iowrite32((rctl & ~PCH_GBE_MRE_MAC_RX_EN), &hw->reg->MAC_RX_EN);
|
|
}
|
|
|
|
static void pch_gbe_enable_mac_rx(struct pch_gbe_hw *hw)
|
|
{
|
|
u32 rctl;
|
|
/* Enables Receive MAC */
|
|
rctl = ioread32(&hw->reg->MAC_RX_EN);
|
|
iowrite32((rctl | PCH_GBE_MRE_MAC_RX_EN), &hw->reg->MAC_RX_EN);
|
|
}
|
|
|
|
/**
|
|
* pch_gbe_mac_init_rx_addrs - Initialize receive address's
|
|
* @hw: Pointer to the HW structure
|
|
* @mar_count: Receive address registers
|
|
*/
|
|
static void pch_gbe_mac_init_rx_addrs(struct pch_gbe_hw *hw, u16 mar_count)
|
|
{
|
|
u32 i;
|
|
|
|
/* Setup the receive address */
|
|
pch_gbe_mac_mar_set(hw, hw->mac.addr, 0);
|
|
|
|
/* Zero out the other receive addresses */
|
|
for (i = 1; i < mar_count; i++) {
|
|
iowrite32(0, &hw->reg->mac_adr[i].high);
|
|
iowrite32(0, &hw->reg->mac_adr[i].low);
|
|
}
|
|
iowrite32(0xFFFE, &hw->reg->ADDR_MASK);
|
|
/* wait busy */
|
|
pch_gbe_wait_clr_bit(&hw->reg->ADDR_MASK, PCH_GBE_BUSY);
|
|
}
|
|
|
|
/**
|
|
* pch_gbe_mac_force_mac_fc - Force the MAC's flow control settings
|
|
* @hw: Pointer to the HW structure
|
|
* Returns:
|
|
* 0: Successful.
|
|
* Negative value: Failed.
|
|
*/
|
|
s32 pch_gbe_mac_force_mac_fc(struct pch_gbe_hw *hw)
|
|
{
|
|
struct pch_gbe_adapter *adapter = pch_gbe_hw_to_adapter(hw);
|
|
struct pch_gbe_mac_info *mac = &hw->mac;
|
|
u32 rx_fctrl;
|
|
|
|
netdev_dbg(adapter->netdev, "mac->fc = %u\n", mac->fc);
|
|
|
|
rx_fctrl = ioread32(&hw->reg->RX_FCTRL);
|
|
|
|
switch (mac->fc) {
|
|
case PCH_GBE_FC_NONE:
|
|
rx_fctrl &= ~PCH_GBE_FL_CTRL_EN;
|
|
mac->tx_fc_enable = false;
|
|
break;
|
|
case PCH_GBE_FC_RX_PAUSE:
|
|
rx_fctrl |= PCH_GBE_FL_CTRL_EN;
|
|
mac->tx_fc_enable = false;
|
|
break;
|
|
case PCH_GBE_FC_TX_PAUSE:
|
|
rx_fctrl &= ~PCH_GBE_FL_CTRL_EN;
|
|
mac->tx_fc_enable = true;
|
|
break;
|
|
case PCH_GBE_FC_FULL:
|
|
rx_fctrl |= PCH_GBE_FL_CTRL_EN;
|
|
mac->tx_fc_enable = true;
|
|
break;
|
|
default:
|
|
netdev_err(adapter->netdev,
|
|
"Flow control param set incorrectly\n");
|
|
return -EINVAL;
|
|
}
|
|
if (mac->link_duplex == DUPLEX_HALF)
|
|
rx_fctrl &= ~PCH_GBE_FL_CTRL_EN;
|
|
iowrite32(rx_fctrl, &hw->reg->RX_FCTRL);
|
|
netdev_dbg(adapter->netdev,
|
|
"RX_FCTRL reg : 0x%08x mac->tx_fc_enable : %d\n",
|
|
ioread32(&hw->reg->RX_FCTRL), mac->tx_fc_enable);
|
|
return 0;
|
|
}
|
|
|
|
/**
|
|
* pch_gbe_mac_set_wol_event - Set wake-on-lan event
|
|
* @hw: Pointer to the HW structure
|
|
* @wu_evt: Wake up event
|
|
*/
|
|
static void pch_gbe_mac_set_wol_event(struct pch_gbe_hw *hw, u32 wu_evt)
|
|
{
|
|
struct pch_gbe_adapter *adapter = pch_gbe_hw_to_adapter(hw);
|
|
u32 addr_mask;
|
|
|
|
netdev_dbg(adapter->netdev, "wu_evt : 0x%08x ADDR_MASK reg : 0x%08x\n",
|
|
wu_evt, ioread32(&hw->reg->ADDR_MASK));
|
|
|
|
if (wu_evt) {
|
|
/* Set Wake-On-Lan address mask */
|
|
addr_mask = ioread32(&hw->reg->ADDR_MASK);
|
|
iowrite32(addr_mask, &hw->reg->WOL_ADDR_MASK);
|
|
/* wait busy */
|
|
pch_gbe_wait_clr_bit(&hw->reg->WOL_ADDR_MASK, PCH_GBE_WLA_BUSY);
|
|
iowrite32(0, &hw->reg->WOL_ST);
|
|
iowrite32((wu_evt | PCH_GBE_WLC_WOL_MODE), &hw->reg->WOL_CTRL);
|
|
iowrite32(0x02, &hw->reg->TCPIP_ACC);
|
|
iowrite32(PCH_GBE_INT_ENABLE_MASK, &hw->reg->INT_EN);
|
|
} else {
|
|
iowrite32(0, &hw->reg->WOL_CTRL);
|
|
iowrite32(0, &hw->reg->WOL_ST);
|
|
}
|
|
return;
|
|
}
|
|
|
|
/**
|
|
* pch_gbe_mac_ctrl_miim - Control MIIM interface
|
|
* @hw: Pointer to the HW structure
|
|
* @addr: Address of PHY
|
|
* @dir: Operetion. (Write or Read)
|
|
* @reg: Access register of PHY
|
|
* @data: Write data.
|
|
*
|
|
* Returns: Read date.
|
|
*/
|
|
u16 pch_gbe_mac_ctrl_miim(struct pch_gbe_hw *hw, u32 addr, u32 dir, u32 reg,
|
|
u16 data)
|
|
{
|
|
struct pch_gbe_adapter *adapter = pch_gbe_hw_to_adapter(hw);
|
|
unsigned long flags;
|
|
u32 data_out;
|
|
|
|
spin_lock_irqsave(&hw->miim_lock, flags);
|
|
|
|
if (readx_poll_timeout_atomic(ioread32, &hw->reg->MIIM, data_out,
|
|
data_out & PCH_GBE_MIIM_OPER_READY, 20, 2000)) {
|
|
netdev_err(adapter->netdev, "pch-gbe.miim won't go Ready\n");
|
|
spin_unlock_irqrestore(&hw->miim_lock, flags);
|
|
return 0; /* No way to indicate timeout error */
|
|
}
|
|
iowrite32(((reg << PCH_GBE_MIIM_REG_ADDR_SHIFT) |
|
|
(addr << PCH_GBE_MIIM_PHY_ADDR_SHIFT) |
|
|
dir | data), &hw->reg->MIIM);
|
|
readx_poll_timeout_atomic(ioread32, &hw->reg->MIIM, data_out,
|
|
data_out & PCH_GBE_MIIM_OPER_READY, 20, 2000);
|
|
spin_unlock_irqrestore(&hw->miim_lock, flags);
|
|
|
|
netdev_dbg(adapter->netdev, "PHY %s: reg=%d, data=0x%04X\n",
|
|
dir == PCH_GBE_MIIM_OPER_READ ? "READ" : "WRITE", reg,
|
|
dir == PCH_GBE_MIIM_OPER_READ ? data_out : data);
|
|
return (u16) data_out;
|
|
}
|
|
|
|
/**
|
|
* pch_gbe_mac_set_pause_packet - Set pause packet
|
|
* @hw: Pointer to the HW structure
|
|
*/
|
|
static void pch_gbe_mac_set_pause_packet(struct pch_gbe_hw *hw)
|
|
{
|
|
struct pch_gbe_adapter *adapter = pch_gbe_hw_to_adapter(hw);
|
|
unsigned long tmp2, tmp3;
|
|
|
|
/* Set Pause packet */
|
|
tmp2 = hw->mac.addr[1];
|
|
tmp2 = (tmp2 << 8) | hw->mac.addr[0];
|
|
tmp2 = PCH_GBE_PAUSE_PKT2_VALUE | (tmp2 << 16);
|
|
|
|
tmp3 = hw->mac.addr[5];
|
|
tmp3 = (tmp3 << 8) | hw->mac.addr[4];
|
|
tmp3 = (tmp3 << 8) | hw->mac.addr[3];
|
|
tmp3 = (tmp3 << 8) | hw->mac.addr[2];
|
|
|
|
iowrite32(PCH_GBE_PAUSE_PKT1_VALUE, &hw->reg->PAUSE_PKT1);
|
|
iowrite32(tmp2, &hw->reg->PAUSE_PKT2);
|
|
iowrite32(tmp3, &hw->reg->PAUSE_PKT3);
|
|
iowrite32(PCH_GBE_PAUSE_PKT4_VALUE, &hw->reg->PAUSE_PKT4);
|
|
iowrite32(PCH_GBE_PAUSE_PKT5_VALUE, &hw->reg->PAUSE_PKT5);
|
|
|
|
/* Transmit Pause Packet */
|
|
iowrite32(PCH_GBE_PS_PKT_RQ, &hw->reg->PAUSE_REQ);
|
|
|
|
netdev_dbg(adapter->netdev,
|
|
"PAUSE_PKT1-5 reg : 0x%08x 0x%08x 0x%08x 0x%08x 0x%08x\n",
|
|
ioread32(&hw->reg->PAUSE_PKT1),
|
|
ioread32(&hw->reg->PAUSE_PKT2),
|
|
ioread32(&hw->reg->PAUSE_PKT3),
|
|
ioread32(&hw->reg->PAUSE_PKT4),
|
|
ioread32(&hw->reg->PAUSE_PKT5));
|
|
|
|
return;
|
|
}
|
|
|
|
|
|
/**
|
|
* pch_gbe_alloc_queues - Allocate memory for all rings
|
|
* @adapter: Board private structure to initialize
|
|
* Returns:
|
|
* 0: Successfully
|
|
* Negative value: Failed
|
|
*/
|
|
static int pch_gbe_alloc_queues(struct pch_gbe_adapter *adapter)
|
|
{
|
|
adapter->tx_ring = devm_kzalloc(&adapter->pdev->dev,
|
|
sizeof(*adapter->tx_ring), GFP_KERNEL);
|
|
if (!adapter->tx_ring)
|
|
return -ENOMEM;
|
|
|
|
adapter->rx_ring = devm_kzalloc(&adapter->pdev->dev,
|
|
sizeof(*adapter->rx_ring), GFP_KERNEL);
|
|
if (!adapter->rx_ring)
|
|
return -ENOMEM;
|
|
return 0;
|
|
}
|
|
|
|
/**
|
|
* pch_gbe_init_stats - Initialize status
|
|
* @adapter: Board private structure to initialize
|
|
*/
|
|
static void pch_gbe_init_stats(struct pch_gbe_adapter *adapter)
|
|
{
|
|
memset(&adapter->stats, 0, sizeof(adapter->stats));
|
|
return;
|
|
}
|
|
|
|
/**
|
|
* pch_gbe_init_phy - Initialize PHY
|
|
* @adapter: Board private structure to initialize
|
|
* Returns:
|
|
* 0: Successfully
|
|
* Negative value: Failed
|
|
*/
|
|
static int pch_gbe_init_phy(struct pch_gbe_adapter *adapter)
|
|
{
|
|
struct net_device *netdev = adapter->netdev;
|
|
u32 addr;
|
|
u16 bmcr, stat;
|
|
|
|
/* Discover phy addr by searching addrs in order {1,0,2,..., 31} */
|
|
for (addr = 0; addr < PCH_GBE_PHY_REGS_LEN; addr++) {
|
|
adapter->mii.phy_id = (addr == 0) ? 1 : (addr == 1) ? 0 : addr;
|
|
bmcr = pch_gbe_mdio_read(netdev, adapter->mii.phy_id, MII_BMCR);
|
|
stat = pch_gbe_mdio_read(netdev, adapter->mii.phy_id, MII_BMSR);
|
|
stat = pch_gbe_mdio_read(netdev, adapter->mii.phy_id, MII_BMSR);
|
|
if (!((bmcr == 0xFFFF) || ((stat == 0) && (bmcr == 0))))
|
|
break;
|
|
}
|
|
adapter->hw.phy.addr = adapter->mii.phy_id;
|
|
netdev_dbg(netdev, "phy_addr = %d\n", adapter->mii.phy_id);
|
|
if (addr == PCH_GBE_PHY_REGS_LEN)
|
|
return -EAGAIN;
|
|
/* Selected the phy and isolate the rest */
|
|
for (addr = 0; addr < PCH_GBE_PHY_REGS_LEN; addr++) {
|
|
if (addr != adapter->mii.phy_id) {
|
|
pch_gbe_mdio_write(netdev, addr, MII_BMCR,
|
|
BMCR_ISOLATE);
|
|
} else {
|
|
bmcr = pch_gbe_mdio_read(netdev, addr, MII_BMCR);
|
|
pch_gbe_mdio_write(netdev, addr, MII_BMCR,
|
|
bmcr & ~BMCR_ISOLATE);
|
|
}
|
|
}
|
|
|
|
/* MII setup */
|
|
adapter->mii.phy_id_mask = 0x1F;
|
|
adapter->mii.reg_num_mask = 0x1F;
|
|
adapter->mii.dev = adapter->netdev;
|
|
adapter->mii.mdio_read = pch_gbe_mdio_read;
|
|
adapter->mii.mdio_write = pch_gbe_mdio_write;
|
|
adapter->mii.supports_gmii = mii_check_gmii_support(&adapter->mii);
|
|
return 0;
|
|
}
|
|
|
|
/**
|
|
* pch_gbe_mdio_read - The read function for mii
|
|
* @netdev: Network interface device structure
|
|
* @addr: Phy ID
|
|
* @reg: Access location
|
|
* Returns:
|
|
* 0: Successfully
|
|
* Negative value: Failed
|
|
*/
|
|
static int pch_gbe_mdio_read(struct net_device *netdev, int addr, int reg)
|
|
{
|
|
struct pch_gbe_adapter *adapter = netdev_priv(netdev);
|
|
struct pch_gbe_hw *hw = &adapter->hw;
|
|
|
|
return pch_gbe_mac_ctrl_miim(hw, addr, PCH_GBE_HAL_MIIM_READ, reg,
|
|
(u16) 0);
|
|
}
|
|
|
|
/**
|
|
* pch_gbe_mdio_write - The write function for mii
|
|
* @netdev: Network interface device structure
|
|
* @addr: Phy ID (not used)
|
|
* @reg: Access location
|
|
* @data: Write data
|
|
*/
|
|
static void pch_gbe_mdio_write(struct net_device *netdev,
|
|
int addr, int reg, int data)
|
|
{
|
|
struct pch_gbe_adapter *adapter = netdev_priv(netdev);
|
|
struct pch_gbe_hw *hw = &adapter->hw;
|
|
|
|
pch_gbe_mac_ctrl_miim(hw, addr, PCH_GBE_HAL_MIIM_WRITE, reg, data);
|
|
}
|
|
|
|
/**
|
|
* pch_gbe_reset_task - Reset processing at the time of transmission timeout
|
|
* @work: Pointer of board private structure
|
|
*/
|
|
static void pch_gbe_reset_task(struct work_struct *work)
|
|
{
|
|
struct pch_gbe_adapter *adapter;
|
|
adapter = container_of(work, struct pch_gbe_adapter, reset_task);
|
|
|
|
rtnl_lock();
|
|
pch_gbe_reinit_locked(adapter);
|
|
rtnl_unlock();
|
|
}
|
|
|
|
/**
|
|
* pch_gbe_reinit_locked- Re-initialization
|
|
* @adapter: Board private structure
|
|
*/
|
|
void pch_gbe_reinit_locked(struct pch_gbe_adapter *adapter)
|
|
{
|
|
pch_gbe_down(adapter);
|
|
pch_gbe_up(adapter);
|
|
}
|
|
|
|
/**
|
|
* pch_gbe_reset - Reset GbE
|
|
* @adapter: Board private structure
|
|
*/
|
|
void pch_gbe_reset(struct pch_gbe_adapter *adapter)
|
|
{
|
|
struct net_device *netdev = adapter->netdev;
|
|
struct pch_gbe_hw *hw = &adapter->hw;
|
|
s32 ret_val;
|
|
|
|
pch_gbe_mac_reset_hw(hw);
|
|
/* reprogram multicast address register after reset */
|
|
pch_gbe_set_multi(netdev);
|
|
/* Setup the receive address. */
|
|
pch_gbe_mac_init_rx_addrs(hw, PCH_GBE_MAR_ENTRIES);
|
|
|
|
ret_val = pch_gbe_phy_get_id(hw);
|
|
if (ret_val) {
|
|
netdev_err(adapter->netdev, "pch_gbe_phy_get_id error\n");
|
|
return;
|
|
}
|
|
pch_gbe_phy_init_setting(hw);
|
|
/* Setup Mac interface option RGMII */
|
|
pch_gbe_phy_set_rgmii(hw);
|
|
}
|
|
|
|
/**
|
|
* pch_gbe_free_irq - Free an interrupt
|
|
* @adapter: Board private structure
|
|
*/
|
|
static void pch_gbe_free_irq(struct pch_gbe_adapter *adapter)
|
|
{
|
|
struct net_device *netdev = adapter->netdev;
|
|
|
|
free_irq(adapter->irq, netdev);
|
|
pci_free_irq_vectors(adapter->pdev);
|
|
}
|
|
|
|
/**
|
|
* pch_gbe_irq_disable - Mask off interrupt generation on the NIC
|
|
* @adapter: Board private structure
|
|
*/
|
|
static void pch_gbe_irq_disable(struct pch_gbe_adapter *adapter)
|
|
{
|
|
struct pch_gbe_hw *hw = &adapter->hw;
|
|
|
|
atomic_inc(&adapter->irq_sem);
|
|
iowrite32(0, &hw->reg->INT_EN);
|
|
ioread32(&hw->reg->INT_ST);
|
|
synchronize_irq(adapter->irq);
|
|
|
|
netdev_dbg(adapter->netdev, "INT_EN reg : 0x%08x\n",
|
|
ioread32(&hw->reg->INT_EN));
|
|
}
|
|
|
|
/**
|
|
* pch_gbe_irq_enable - Enable default interrupt generation settings
|
|
* @adapter: Board private structure
|
|
*/
|
|
static void pch_gbe_irq_enable(struct pch_gbe_adapter *adapter)
|
|
{
|
|
struct pch_gbe_hw *hw = &adapter->hw;
|
|
|
|
if (likely(atomic_dec_and_test(&adapter->irq_sem)))
|
|
iowrite32(PCH_GBE_INT_ENABLE_MASK, &hw->reg->INT_EN);
|
|
ioread32(&hw->reg->INT_ST);
|
|
netdev_dbg(adapter->netdev, "INT_EN reg : 0x%08x\n",
|
|
ioread32(&hw->reg->INT_EN));
|
|
}
|
|
|
|
|
|
|
|
/**
|
|
* pch_gbe_setup_tctl - configure the Transmit control registers
|
|
* @adapter: Board private structure
|
|
*/
|
|
static void pch_gbe_setup_tctl(struct pch_gbe_adapter *adapter)
|
|
{
|
|
struct pch_gbe_hw *hw = &adapter->hw;
|
|
u32 tx_mode, tcpip;
|
|
|
|
tx_mode = PCH_GBE_TM_LONG_PKT |
|
|
PCH_GBE_TM_ST_AND_FD |
|
|
PCH_GBE_TM_SHORT_PKT |
|
|
PCH_GBE_TM_TH_TX_STRT_8 |
|
|
PCH_GBE_TM_TH_ALM_EMP_4 | PCH_GBE_TM_TH_ALM_FULL_8;
|
|
|
|
iowrite32(tx_mode, &hw->reg->TX_MODE);
|
|
|
|
tcpip = ioread32(&hw->reg->TCPIP_ACC);
|
|
tcpip |= PCH_GBE_TX_TCPIPACC_EN;
|
|
iowrite32(tcpip, &hw->reg->TCPIP_ACC);
|
|
return;
|
|
}
|
|
|
|
/**
|
|
* pch_gbe_configure_tx - Configure Transmit Unit after Reset
|
|
* @adapter: Board private structure
|
|
*/
|
|
static void pch_gbe_configure_tx(struct pch_gbe_adapter *adapter)
|
|
{
|
|
struct pch_gbe_hw *hw = &adapter->hw;
|
|
u32 tdba, tdlen, dctrl;
|
|
|
|
netdev_dbg(adapter->netdev, "dma addr = 0x%08llx size = 0x%08x\n",
|
|
(unsigned long long)adapter->tx_ring->dma,
|
|
adapter->tx_ring->size);
|
|
|
|
/* Setup the HW Tx Head and Tail descriptor pointers */
|
|
tdba = adapter->tx_ring->dma;
|
|
tdlen = adapter->tx_ring->size - 0x10;
|
|
iowrite32(tdba, &hw->reg->TX_DSC_BASE);
|
|
iowrite32(tdlen, &hw->reg->TX_DSC_SIZE);
|
|
iowrite32(tdba, &hw->reg->TX_DSC_SW_P);
|
|
|
|
/* Enables Transmission DMA */
|
|
dctrl = ioread32(&hw->reg->DMA_CTRL);
|
|
dctrl |= PCH_GBE_TX_DMA_EN;
|
|
iowrite32(dctrl, &hw->reg->DMA_CTRL);
|
|
}
|
|
|
|
/**
|
|
* pch_gbe_setup_rctl - Configure the receive control registers
|
|
* @adapter: Board private structure
|
|
*/
|
|
static void pch_gbe_setup_rctl(struct pch_gbe_adapter *adapter)
|
|
{
|
|
struct pch_gbe_hw *hw = &adapter->hw;
|
|
u32 rx_mode, tcpip;
|
|
|
|
rx_mode = PCH_GBE_ADD_FIL_EN | PCH_GBE_MLT_FIL_EN |
|
|
PCH_GBE_RH_ALM_EMP_4 | PCH_GBE_RH_ALM_FULL_4 | PCH_GBE_RH_RD_TRG_8;
|
|
|
|
iowrite32(rx_mode, &hw->reg->RX_MODE);
|
|
|
|
tcpip = ioread32(&hw->reg->TCPIP_ACC);
|
|
|
|
tcpip |= PCH_GBE_RX_TCPIPACC_OFF;
|
|
tcpip &= ~PCH_GBE_RX_TCPIPACC_EN;
|
|
iowrite32(tcpip, &hw->reg->TCPIP_ACC);
|
|
return;
|
|
}
|
|
|
|
/**
|
|
* pch_gbe_configure_rx - Configure Receive Unit after Reset
|
|
* @adapter: Board private structure
|
|
*/
|
|
static void pch_gbe_configure_rx(struct pch_gbe_adapter *adapter)
|
|
{
|
|
struct pch_gbe_hw *hw = &adapter->hw;
|
|
u32 rdba, rdlen, rxdma;
|
|
|
|
netdev_dbg(adapter->netdev, "dma adr = 0x%08llx size = 0x%08x\n",
|
|
(unsigned long long)adapter->rx_ring->dma,
|
|
adapter->rx_ring->size);
|
|
|
|
pch_gbe_mac_force_mac_fc(hw);
|
|
|
|
pch_gbe_disable_mac_rx(hw);
|
|
|
|
/* Disables Receive DMA */
|
|
rxdma = ioread32(&hw->reg->DMA_CTRL);
|
|
rxdma &= ~PCH_GBE_RX_DMA_EN;
|
|
iowrite32(rxdma, &hw->reg->DMA_CTRL);
|
|
|
|
netdev_dbg(adapter->netdev,
|
|
"MAC_RX_EN reg = 0x%08x DMA_CTRL reg = 0x%08x\n",
|
|
ioread32(&hw->reg->MAC_RX_EN),
|
|
ioread32(&hw->reg->DMA_CTRL));
|
|
|
|
/* Setup the HW Rx Head and Tail Descriptor Pointers and
|
|
* the Base and Length of the Rx Descriptor Ring */
|
|
rdba = adapter->rx_ring->dma;
|
|
rdlen = adapter->rx_ring->size - 0x10;
|
|
iowrite32(rdba, &hw->reg->RX_DSC_BASE);
|
|
iowrite32(rdlen, &hw->reg->RX_DSC_SIZE);
|
|
iowrite32((rdba + rdlen), &hw->reg->RX_DSC_SW_P);
|
|
}
|
|
|
|
/**
|
|
* pch_gbe_unmap_and_free_tx_resource - Unmap and free tx socket buffer
|
|
* @adapter: Board private structure
|
|
* @buffer_info: Buffer information structure
|
|
*/
|
|
static void pch_gbe_unmap_and_free_tx_resource(
|
|
struct pch_gbe_adapter *adapter, struct pch_gbe_buffer *buffer_info)
|
|
{
|
|
if (buffer_info->mapped) {
|
|
dma_unmap_single(&adapter->pdev->dev, buffer_info->dma,
|
|
buffer_info->length, DMA_TO_DEVICE);
|
|
buffer_info->mapped = false;
|
|
}
|
|
if (buffer_info->skb) {
|
|
dev_kfree_skb_any(buffer_info->skb);
|
|
buffer_info->skb = NULL;
|
|
}
|
|
}
|
|
|
|
/**
|
|
* pch_gbe_unmap_and_free_rx_resource - Unmap and free rx socket buffer
|
|
* @adapter: Board private structure
|
|
* @buffer_info: Buffer information structure
|
|
*/
|
|
static void pch_gbe_unmap_and_free_rx_resource(
|
|
struct pch_gbe_adapter *adapter,
|
|
struct pch_gbe_buffer *buffer_info)
|
|
{
|
|
if (buffer_info->mapped) {
|
|
dma_unmap_single(&adapter->pdev->dev, buffer_info->dma,
|
|
buffer_info->length, DMA_FROM_DEVICE);
|
|
buffer_info->mapped = false;
|
|
}
|
|
if (buffer_info->skb) {
|
|
dev_kfree_skb_any(buffer_info->skb);
|
|
buffer_info->skb = NULL;
|
|
}
|
|
}
|
|
|
|
/**
|
|
* pch_gbe_clean_tx_ring - Free Tx Buffers
|
|
* @adapter: Board private structure
|
|
* @tx_ring: Ring to be cleaned
|
|
*/
|
|
static void pch_gbe_clean_tx_ring(struct pch_gbe_adapter *adapter,
|
|
struct pch_gbe_tx_ring *tx_ring)
|
|
{
|
|
struct pch_gbe_hw *hw = &adapter->hw;
|
|
struct pch_gbe_buffer *buffer_info;
|
|
unsigned long size;
|
|
unsigned int i;
|
|
|
|
/* Free all the Tx ring sk_buffs */
|
|
for (i = 0; i < tx_ring->count; i++) {
|
|
buffer_info = &tx_ring->buffer_info[i];
|
|
pch_gbe_unmap_and_free_tx_resource(adapter, buffer_info);
|
|
}
|
|
netdev_dbg(adapter->netdev,
|
|
"call pch_gbe_unmap_and_free_tx_resource() %d count\n", i);
|
|
|
|
size = (unsigned long)sizeof(struct pch_gbe_buffer) * tx_ring->count;
|
|
memset(tx_ring->buffer_info, 0, size);
|
|
|
|
/* Zero out the descriptor ring */
|
|
memset(tx_ring->desc, 0, tx_ring->size);
|
|
tx_ring->next_to_use = 0;
|
|
tx_ring->next_to_clean = 0;
|
|
iowrite32(tx_ring->dma, &hw->reg->TX_DSC_HW_P);
|
|
iowrite32((tx_ring->size - 0x10), &hw->reg->TX_DSC_SIZE);
|
|
}
|
|
|
|
/**
|
|
* pch_gbe_clean_rx_ring - Free Rx Buffers
|
|
* @adapter: Board private structure
|
|
* @rx_ring: Ring to free buffers from
|
|
*/
|
|
static void
|
|
pch_gbe_clean_rx_ring(struct pch_gbe_adapter *adapter,
|
|
struct pch_gbe_rx_ring *rx_ring)
|
|
{
|
|
struct pch_gbe_hw *hw = &adapter->hw;
|
|
struct pch_gbe_buffer *buffer_info;
|
|
unsigned long size;
|
|
unsigned int i;
|
|
|
|
/* Free all the Rx ring sk_buffs */
|
|
for (i = 0; i < rx_ring->count; i++) {
|
|
buffer_info = &rx_ring->buffer_info[i];
|
|
pch_gbe_unmap_and_free_rx_resource(adapter, buffer_info);
|
|
}
|
|
netdev_dbg(adapter->netdev,
|
|
"call pch_gbe_unmap_and_free_rx_resource() %d count\n", i);
|
|
size = (unsigned long)sizeof(struct pch_gbe_buffer) * rx_ring->count;
|
|
memset(rx_ring->buffer_info, 0, size);
|
|
|
|
/* Zero out the descriptor ring */
|
|
memset(rx_ring->desc, 0, rx_ring->size);
|
|
rx_ring->next_to_clean = 0;
|
|
rx_ring->next_to_use = 0;
|
|
iowrite32(rx_ring->dma, &hw->reg->RX_DSC_HW_P);
|
|
iowrite32((rx_ring->size - 0x10), &hw->reg->RX_DSC_SIZE);
|
|
}
|
|
|
|
static void pch_gbe_set_rgmii_ctrl(struct pch_gbe_adapter *adapter, u16 speed,
|
|
u16 duplex)
|
|
{
|
|
struct pch_gbe_hw *hw = &adapter->hw;
|
|
unsigned long rgmii = 0;
|
|
|
|
/* Set the RGMII control. */
|
|
switch (speed) {
|
|
case SPEED_10:
|
|
rgmii = (PCH_GBE_RGMII_RATE_2_5M |
|
|
PCH_GBE_MAC_RGMII_CTRL_SETTING);
|
|
break;
|
|
case SPEED_100:
|
|
rgmii = (PCH_GBE_RGMII_RATE_25M |
|
|
PCH_GBE_MAC_RGMII_CTRL_SETTING);
|
|
break;
|
|
case SPEED_1000:
|
|
rgmii = (PCH_GBE_RGMII_RATE_125M |
|
|
PCH_GBE_MAC_RGMII_CTRL_SETTING);
|
|
break;
|
|
}
|
|
iowrite32(rgmii, &hw->reg->RGMII_CTRL);
|
|
}
|
|
static void pch_gbe_set_mode(struct pch_gbe_adapter *adapter, u16 speed,
|
|
u16 duplex)
|
|
{
|
|
struct net_device *netdev = adapter->netdev;
|
|
struct pch_gbe_hw *hw = &adapter->hw;
|
|
unsigned long mode = 0;
|
|
|
|
/* Set the communication mode */
|
|
switch (speed) {
|
|
case SPEED_10:
|
|
mode = PCH_GBE_MODE_MII_ETHER;
|
|
netdev->tx_queue_len = 10;
|
|
break;
|
|
case SPEED_100:
|
|
mode = PCH_GBE_MODE_MII_ETHER;
|
|
netdev->tx_queue_len = 100;
|
|
break;
|
|
case SPEED_1000:
|
|
mode = PCH_GBE_MODE_GMII_ETHER;
|
|
break;
|
|
}
|
|
if (duplex == DUPLEX_FULL)
|
|
mode |= PCH_GBE_MODE_FULL_DUPLEX;
|
|
else
|
|
mode |= PCH_GBE_MODE_HALF_DUPLEX;
|
|
iowrite32(mode, &hw->reg->MODE);
|
|
}
|
|
|
|
/**
|
|
* pch_gbe_watchdog - Watchdog process
|
|
* @t: timer list containing a Board private structure
|
|
*/
|
|
static void pch_gbe_watchdog(struct timer_list *t)
|
|
{
|
|
struct pch_gbe_adapter *adapter = from_timer(adapter, t,
|
|
watchdog_timer);
|
|
struct net_device *netdev = adapter->netdev;
|
|
struct pch_gbe_hw *hw = &adapter->hw;
|
|
|
|
netdev_dbg(netdev, "right now = %ld\n", jiffies);
|
|
|
|
pch_gbe_update_stats(adapter);
|
|
if ((mii_link_ok(&adapter->mii)) && (!netif_carrier_ok(netdev))) {
|
|
struct ethtool_cmd cmd = { .cmd = ETHTOOL_GSET };
|
|
netdev->tx_queue_len = adapter->tx_queue_len;
|
|
/* mii library handles link maintenance tasks */
|
|
mii_ethtool_gset(&adapter->mii, &cmd);
|
|
hw->mac.link_speed = ethtool_cmd_speed(&cmd);
|
|
hw->mac.link_duplex = cmd.duplex;
|
|
/* Set the RGMII control. */
|
|
pch_gbe_set_rgmii_ctrl(adapter, hw->mac.link_speed,
|
|
hw->mac.link_duplex);
|
|
/* Set the communication mode */
|
|
pch_gbe_set_mode(adapter, hw->mac.link_speed,
|
|
hw->mac.link_duplex);
|
|
netdev_dbg(netdev,
|
|
"Link is Up %d Mbps %s-Duplex\n",
|
|
hw->mac.link_speed,
|
|
cmd.duplex == DUPLEX_FULL ? "Full" : "Half");
|
|
netif_carrier_on(netdev);
|
|
netif_wake_queue(netdev);
|
|
} else if ((!mii_link_ok(&adapter->mii)) &&
|
|
(netif_carrier_ok(netdev))) {
|
|
netdev_dbg(netdev, "NIC Link is Down\n");
|
|
hw->mac.link_speed = SPEED_10;
|
|
hw->mac.link_duplex = DUPLEX_HALF;
|
|
netif_carrier_off(netdev);
|
|
netif_stop_queue(netdev);
|
|
}
|
|
mod_timer(&adapter->watchdog_timer,
|
|
round_jiffies(jiffies + PCH_GBE_WATCHDOG_PERIOD));
|
|
}
|
|
|
|
/**
|
|
* pch_gbe_tx_queue - Carry out queuing of the transmission data
|
|
* @adapter: Board private structure
|
|
* @tx_ring: Tx descriptor ring structure
|
|
* @skb: Sockt buffer structure
|
|
*/
|
|
static void pch_gbe_tx_queue(struct pch_gbe_adapter *adapter,
|
|
struct pch_gbe_tx_ring *tx_ring,
|
|
struct sk_buff *skb)
|
|
{
|
|
struct pch_gbe_hw *hw = &adapter->hw;
|
|
struct pch_gbe_tx_desc *tx_desc;
|
|
struct pch_gbe_buffer *buffer_info;
|
|
struct sk_buff *tmp_skb;
|
|
unsigned int frame_ctrl;
|
|
unsigned int ring_num;
|
|
|
|
/*-- Set frame control --*/
|
|
frame_ctrl = 0;
|
|
if (unlikely(skb->len < PCH_GBE_SHORT_PKT))
|
|
frame_ctrl |= PCH_GBE_TXD_CTRL_APAD;
|
|
if (skb->ip_summed == CHECKSUM_NONE)
|
|
frame_ctrl |= PCH_GBE_TXD_CTRL_TCPIP_ACC_OFF;
|
|
|
|
/* Performs checksum processing */
|
|
/*
|
|
* It is because the hardware accelerator does not support a checksum,
|
|
* when the received data size is less than 64 bytes.
|
|
*/
|
|
if (skb->len < PCH_GBE_SHORT_PKT && skb->ip_summed != CHECKSUM_NONE) {
|
|
frame_ctrl |= PCH_GBE_TXD_CTRL_APAD |
|
|
PCH_GBE_TXD_CTRL_TCPIP_ACC_OFF;
|
|
if (skb->protocol == htons(ETH_P_IP)) {
|
|
struct iphdr *iph = ip_hdr(skb);
|
|
unsigned int offset;
|
|
offset = skb_transport_offset(skb);
|
|
if (iph->protocol == IPPROTO_TCP) {
|
|
skb->csum = 0;
|
|
tcp_hdr(skb)->check = 0;
|
|
skb->csum = skb_checksum(skb, offset,
|
|
skb->len - offset, 0);
|
|
tcp_hdr(skb)->check =
|
|
csum_tcpudp_magic(iph->saddr,
|
|
iph->daddr,
|
|
skb->len - offset,
|
|
IPPROTO_TCP,
|
|
skb->csum);
|
|
} else if (iph->protocol == IPPROTO_UDP) {
|
|
skb->csum = 0;
|
|
udp_hdr(skb)->check = 0;
|
|
skb->csum =
|
|
skb_checksum(skb, offset,
|
|
skb->len - offset, 0);
|
|
udp_hdr(skb)->check =
|
|
csum_tcpudp_magic(iph->saddr,
|
|
iph->daddr,
|
|
skb->len - offset,
|
|
IPPROTO_UDP,
|
|
skb->csum);
|
|
}
|
|
}
|
|
}
|
|
|
|
ring_num = tx_ring->next_to_use;
|
|
if (unlikely((ring_num + 1) == tx_ring->count))
|
|
tx_ring->next_to_use = 0;
|
|
else
|
|
tx_ring->next_to_use = ring_num + 1;
|
|
|
|
|
|
buffer_info = &tx_ring->buffer_info[ring_num];
|
|
tmp_skb = buffer_info->skb;
|
|
|
|
/* [Header:14][payload] ---> [Header:14][paddong:2][payload] */
|
|
memcpy(tmp_skb->data, skb->data, ETH_HLEN);
|
|
tmp_skb->data[ETH_HLEN] = 0x00;
|
|
tmp_skb->data[ETH_HLEN + 1] = 0x00;
|
|
tmp_skb->len = skb->len;
|
|
memcpy(&tmp_skb->data[ETH_HLEN + 2], &skb->data[ETH_HLEN],
|
|
(skb->len - ETH_HLEN));
|
|
/*-- Set Buffer information --*/
|
|
buffer_info->length = tmp_skb->len;
|
|
buffer_info->dma = dma_map_single(&adapter->pdev->dev, tmp_skb->data,
|
|
buffer_info->length,
|
|
DMA_TO_DEVICE);
|
|
if (dma_mapping_error(&adapter->pdev->dev, buffer_info->dma)) {
|
|
netdev_err(adapter->netdev, "TX DMA map failed\n");
|
|
buffer_info->dma = 0;
|
|
buffer_info->time_stamp = 0;
|
|
tx_ring->next_to_use = ring_num;
|
|
dev_kfree_skb_any(skb);
|
|
return;
|
|
}
|
|
buffer_info->mapped = true;
|
|
buffer_info->time_stamp = jiffies;
|
|
|
|
/*-- Set Tx descriptor --*/
|
|
tx_desc = PCH_GBE_TX_DESC(*tx_ring, ring_num);
|
|
tx_desc->buffer_addr = (buffer_info->dma);
|
|
tx_desc->length = (tmp_skb->len);
|
|
tx_desc->tx_words_eob = ((tmp_skb->len + 3));
|
|
tx_desc->tx_frame_ctrl = (frame_ctrl);
|
|
tx_desc->gbec_status = (DSC_INIT16);
|
|
|
|
if (unlikely(++ring_num == tx_ring->count))
|
|
ring_num = 0;
|
|
|
|
/* Update software pointer of TX descriptor */
|
|
iowrite32(tx_ring->dma +
|
|
(int)sizeof(struct pch_gbe_tx_desc) * ring_num,
|
|
&hw->reg->TX_DSC_SW_P);
|
|
|
|
pch_tx_timestamp(adapter, skb);
|
|
|
|
dev_kfree_skb_any(skb);
|
|
}
|
|
|
|
/**
|
|
* pch_gbe_update_stats - Update the board statistics counters
|
|
* @adapter: Board private structure
|
|
*/
|
|
void pch_gbe_update_stats(struct pch_gbe_adapter *adapter)
|
|
{
|
|
struct net_device *netdev = adapter->netdev;
|
|
struct pci_dev *pdev = adapter->pdev;
|
|
struct pch_gbe_hw_stats *stats = &adapter->stats;
|
|
unsigned long flags;
|
|
|
|
/*
|
|
* Prevent stats update while adapter is being reset, or if the pci
|
|
* connection is down.
|
|
*/
|
|
if ((pdev->error_state) && (pdev->error_state != pci_channel_io_normal))
|
|
return;
|
|
|
|
spin_lock_irqsave(&adapter->stats_lock, flags);
|
|
|
|
/* Update device status "adapter->stats" */
|
|
stats->rx_errors = stats->rx_crc_errors + stats->rx_frame_errors;
|
|
stats->tx_errors = stats->tx_length_errors +
|
|
stats->tx_aborted_errors +
|
|
stats->tx_carrier_errors + stats->tx_timeout_count;
|
|
|
|
/* Update network device status "adapter->net_stats" */
|
|
netdev->stats.rx_packets = stats->rx_packets;
|
|
netdev->stats.rx_bytes = stats->rx_bytes;
|
|
netdev->stats.rx_dropped = stats->rx_dropped;
|
|
netdev->stats.tx_packets = stats->tx_packets;
|
|
netdev->stats.tx_bytes = stats->tx_bytes;
|
|
netdev->stats.tx_dropped = stats->tx_dropped;
|
|
/* Fill out the OS statistics structure */
|
|
netdev->stats.multicast = stats->multicast;
|
|
netdev->stats.collisions = stats->collisions;
|
|
/* Rx Errors */
|
|
netdev->stats.rx_errors = stats->rx_errors;
|
|
netdev->stats.rx_crc_errors = stats->rx_crc_errors;
|
|
netdev->stats.rx_frame_errors = stats->rx_frame_errors;
|
|
/* Tx Errors */
|
|
netdev->stats.tx_errors = stats->tx_errors;
|
|
netdev->stats.tx_aborted_errors = stats->tx_aborted_errors;
|
|
netdev->stats.tx_carrier_errors = stats->tx_carrier_errors;
|
|
|
|
spin_unlock_irqrestore(&adapter->stats_lock, flags);
|
|
}
|
|
|
|
static void pch_gbe_disable_dma_rx(struct pch_gbe_hw *hw)
|
|
{
|
|
u32 rxdma;
|
|
|
|
/* Disable Receive DMA */
|
|
rxdma = ioread32(&hw->reg->DMA_CTRL);
|
|
rxdma &= ~PCH_GBE_RX_DMA_EN;
|
|
iowrite32(rxdma, &hw->reg->DMA_CTRL);
|
|
}
|
|
|
|
static void pch_gbe_enable_dma_rx(struct pch_gbe_hw *hw)
|
|
{
|
|
u32 rxdma;
|
|
|
|
/* Enables Receive DMA */
|
|
rxdma = ioread32(&hw->reg->DMA_CTRL);
|
|
rxdma |= PCH_GBE_RX_DMA_EN;
|
|
iowrite32(rxdma, &hw->reg->DMA_CTRL);
|
|
}
|
|
|
|
/**
|
|
* pch_gbe_intr - Interrupt Handler
|
|
* @irq: Interrupt number
|
|
* @data: Pointer to a network interface device structure
|
|
* Returns:
|
|
* - IRQ_HANDLED: Our interrupt
|
|
* - IRQ_NONE: Not our interrupt
|
|
*/
|
|
static irqreturn_t pch_gbe_intr(int irq, void *data)
|
|
{
|
|
struct net_device *netdev = data;
|
|
struct pch_gbe_adapter *adapter = netdev_priv(netdev);
|
|
struct pch_gbe_hw *hw = &adapter->hw;
|
|
u32 int_st;
|
|
u32 int_en;
|
|
|
|
/* Check request status */
|
|
int_st = ioread32(&hw->reg->INT_ST);
|
|
int_st = int_st & ioread32(&hw->reg->INT_EN);
|
|
/* When request status is no interruption factor */
|
|
if (unlikely(!int_st))
|
|
return IRQ_NONE; /* Not our interrupt. End processing. */
|
|
netdev_dbg(netdev, "%s occur int_st = 0x%08x\n", __func__, int_st);
|
|
if (int_st & PCH_GBE_INT_RX_FRAME_ERR)
|
|
adapter->stats.intr_rx_frame_err_count++;
|
|
if (int_st & PCH_GBE_INT_RX_FIFO_ERR)
|
|
if (!adapter->rx_stop_flag) {
|
|
adapter->stats.intr_rx_fifo_err_count++;
|
|
netdev_dbg(netdev, "Rx fifo over run\n");
|
|
adapter->rx_stop_flag = true;
|
|
int_en = ioread32(&hw->reg->INT_EN);
|
|
iowrite32((int_en & ~PCH_GBE_INT_RX_FIFO_ERR),
|
|
&hw->reg->INT_EN);
|
|
pch_gbe_disable_dma_rx(&adapter->hw);
|
|
int_st |= ioread32(&hw->reg->INT_ST);
|
|
int_st = int_st & ioread32(&hw->reg->INT_EN);
|
|
}
|
|
if (int_st & PCH_GBE_INT_RX_DMA_ERR)
|
|
adapter->stats.intr_rx_dma_err_count++;
|
|
if (int_st & PCH_GBE_INT_TX_FIFO_ERR)
|
|
adapter->stats.intr_tx_fifo_err_count++;
|
|
if (int_st & PCH_GBE_INT_TX_DMA_ERR)
|
|
adapter->stats.intr_tx_dma_err_count++;
|
|
if (int_st & PCH_GBE_INT_TCPIP_ERR)
|
|
adapter->stats.intr_tcpip_err_count++;
|
|
/* When Rx descriptor is empty */
|
|
if ((int_st & PCH_GBE_INT_RX_DSC_EMP)) {
|
|
adapter->stats.intr_rx_dsc_empty_count++;
|
|
netdev_dbg(netdev, "Rx descriptor is empty\n");
|
|
int_en = ioread32(&hw->reg->INT_EN);
|
|
iowrite32((int_en & ~PCH_GBE_INT_RX_DSC_EMP), &hw->reg->INT_EN);
|
|
if (hw->mac.tx_fc_enable) {
|
|
/* Set Pause packet */
|
|
pch_gbe_mac_set_pause_packet(hw);
|
|
}
|
|
}
|
|
|
|
/* When request status is Receive interruption */
|
|
if ((int_st & (PCH_GBE_INT_RX_DMA_CMPLT | PCH_GBE_INT_TX_CMPLT)) ||
|
|
(adapter->rx_stop_flag)) {
|
|
if (likely(napi_schedule_prep(&adapter->napi))) {
|
|
/* Enable only Rx Descriptor empty */
|
|
atomic_inc(&adapter->irq_sem);
|
|
int_en = ioread32(&hw->reg->INT_EN);
|
|
int_en &=
|
|
~(PCH_GBE_INT_RX_DMA_CMPLT | PCH_GBE_INT_TX_CMPLT);
|
|
iowrite32(int_en, &hw->reg->INT_EN);
|
|
/* Start polling for NAPI */
|
|
__napi_schedule(&adapter->napi);
|
|
}
|
|
}
|
|
netdev_dbg(netdev, "return = 0x%08x INT_EN reg = 0x%08x\n",
|
|
IRQ_HANDLED, ioread32(&hw->reg->INT_EN));
|
|
return IRQ_HANDLED;
|
|
}
|
|
|
|
/**
|
|
* pch_gbe_alloc_rx_buffers - Replace used receive buffers; legacy & extended
|
|
* @adapter: Board private structure
|
|
* @rx_ring: Rx descriptor ring
|
|
* @cleaned_count: Cleaned count
|
|
*/
|
|
static void
|
|
pch_gbe_alloc_rx_buffers(struct pch_gbe_adapter *adapter,
|
|
struct pch_gbe_rx_ring *rx_ring, int cleaned_count)
|
|
{
|
|
struct net_device *netdev = adapter->netdev;
|
|
struct pci_dev *pdev = adapter->pdev;
|
|
struct pch_gbe_hw *hw = &adapter->hw;
|
|
struct pch_gbe_rx_desc *rx_desc;
|
|
struct pch_gbe_buffer *buffer_info;
|
|
struct sk_buff *skb;
|
|
unsigned int i;
|
|
unsigned int bufsz;
|
|
|
|
bufsz = adapter->rx_buffer_len + NET_IP_ALIGN;
|
|
i = rx_ring->next_to_use;
|
|
|
|
while ((cleaned_count--)) {
|
|
buffer_info = &rx_ring->buffer_info[i];
|
|
skb = netdev_alloc_skb(netdev, bufsz);
|
|
if (unlikely(!skb)) {
|
|
/* Better luck next round */
|
|
adapter->stats.rx_alloc_buff_failed++;
|
|
break;
|
|
}
|
|
/* align */
|
|
skb_reserve(skb, NET_IP_ALIGN);
|
|
buffer_info->skb = skb;
|
|
|
|
buffer_info->dma = dma_map_single(&pdev->dev,
|
|
buffer_info->rx_buffer,
|
|
buffer_info->length,
|
|
DMA_FROM_DEVICE);
|
|
if (dma_mapping_error(&adapter->pdev->dev, buffer_info->dma)) {
|
|
dev_kfree_skb(skb);
|
|
buffer_info->skb = NULL;
|
|
buffer_info->dma = 0;
|
|
adapter->stats.rx_alloc_buff_failed++;
|
|
break; /* while !buffer_info->skb */
|
|
}
|
|
buffer_info->mapped = true;
|
|
rx_desc = PCH_GBE_RX_DESC(*rx_ring, i);
|
|
rx_desc->buffer_addr = (buffer_info->dma);
|
|
rx_desc->gbec_status = DSC_INIT16;
|
|
|
|
netdev_dbg(netdev,
|
|
"i = %d buffer_info->dma = 0x08%llx buffer_info->length = 0x%x\n",
|
|
i, (unsigned long long)buffer_info->dma,
|
|
buffer_info->length);
|
|
|
|
if (unlikely(++i == rx_ring->count))
|
|
i = 0;
|
|
}
|
|
if (likely(rx_ring->next_to_use != i)) {
|
|
rx_ring->next_to_use = i;
|
|
if (unlikely(i-- == 0))
|
|
i = (rx_ring->count - 1);
|
|
iowrite32(rx_ring->dma +
|
|
(int)sizeof(struct pch_gbe_rx_desc) * i,
|
|
&hw->reg->RX_DSC_SW_P);
|
|
}
|
|
return;
|
|
}
|
|
|
|
static int
|
|
pch_gbe_alloc_rx_buffers_pool(struct pch_gbe_adapter *adapter,
|
|
struct pch_gbe_rx_ring *rx_ring, int cleaned_count)
|
|
{
|
|
struct pci_dev *pdev = adapter->pdev;
|
|
struct pch_gbe_buffer *buffer_info;
|
|
unsigned int i;
|
|
unsigned int bufsz;
|
|
unsigned int size;
|
|
|
|
bufsz = adapter->rx_buffer_len;
|
|
|
|
size = rx_ring->count * bufsz + PCH_GBE_RESERVE_MEMORY;
|
|
rx_ring->rx_buff_pool =
|
|
dma_alloc_coherent(&pdev->dev, size,
|
|
&rx_ring->rx_buff_pool_logic, GFP_KERNEL);
|
|
if (!rx_ring->rx_buff_pool)
|
|
return -ENOMEM;
|
|
|
|
rx_ring->rx_buff_pool_size = size;
|
|
for (i = 0; i < rx_ring->count; i++) {
|
|
buffer_info = &rx_ring->buffer_info[i];
|
|
buffer_info->rx_buffer = rx_ring->rx_buff_pool + bufsz * i;
|
|
buffer_info->length = bufsz;
|
|
}
|
|
return 0;
|
|
}
|
|
|
|
/**
|
|
* pch_gbe_alloc_tx_buffers - Allocate transmit buffers
|
|
* @adapter: Board private structure
|
|
* @tx_ring: Tx descriptor ring
|
|
*/
|
|
static void pch_gbe_alloc_tx_buffers(struct pch_gbe_adapter *adapter,
|
|
struct pch_gbe_tx_ring *tx_ring)
|
|
{
|
|
struct pch_gbe_buffer *buffer_info;
|
|
struct sk_buff *skb;
|
|
unsigned int i;
|
|
unsigned int bufsz;
|
|
struct pch_gbe_tx_desc *tx_desc;
|
|
|
|
bufsz =
|
|
adapter->hw.mac.max_frame_size + PCH_GBE_DMA_ALIGN + NET_IP_ALIGN;
|
|
|
|
for (i = 0; i < tx_ring->count; i++) {
|
|
buffer_info = &tx_ring->buffer_info[i];
|
|
skb = netdev_alloc_skb(adapter->netdev, bufsz);
|
|
skb_reserve(skb, PCH_GBE_DMA_ALIGN);
|
|
buffer_info->skb = skb;
|
|
tx_desc = PCH_GBE_TX_DESC(*tx_ring, i);
|
|
tx_desc->gbec_status = (DSC_INIT16);
|
|
}
|
|
return;
|
|
}
|
|
|
|
/**
|
|
* pch_gbe_clean_tx - Reclaim resources after transmit completes
|
|
* @adapter: Board private structure
|
|
* @tx_ring: Tx descriptor ring
|
|
* Returns:
|
|
* true: Cleaned the descriptor
|
|
* false: Not cleaned the descriptor
|
|
*/
|
|
static bool
|
|
pch_gbe_clean_tx(struct pch_gbe_adapter *adapter,
|
|
struct pch_gbe_tx_ring *tx_ring)
|
|
{
|
|
struct pch_gbe_tx_desc *tx_desc;
|
|
struct pch_gbe_buffer *buffer_info;
|
|
struct sk_buff *skb;
|
|
unsigned int i;
|
|
unsigned int cleaned_count = 0;
|
|
bool cleaned = false;
|
|
int unused, thresh;
|
|
|
|
netdev_dbg(adapter->netdev, "next_to_clean : %d\n",
|
|
tx_ring->next_to_clean);
|
|
|
|
i = tx_ring->next_to_clean;
|
|
tx_desc = PCH_GBE_TX_DESC(*tx_ring, i);
|
|
netdev_dbg(adapter->netdev, "gbec_status:0x%04x dma_status:0x%04x\n",
|
|
tx_desc->gbec_status, tx_desc->dma_status);
|
|
|
|
unused = PCH_GBE_DESC_UNUSED(tx_ring);
|
|
thresh = tx_ring->count - NAPI_POLL_WEIGHT;
|
|
if ((tx_desc->gbec_status == DSC_INIT16) && (unused < thresh))
|
|
{ /* current marked clean, tx queue filling up, do extra clean */
|
|
int j, k;
|
|
if (unused < 8) { /* tx queue nearly full */
|
|
netdev_dbg(adapter->netdev,
|
|
"clean_tx: transmit queue warning (%x,%x) unused=%d\n",
|
|
tx_ring->next_to_clean, tx_ring->next_to_use,
|
|
unused);
|
|
}
|
|
|
|
/* current marked clean, scan for more that need cleaning. */
|
|
k = i;
|
|
for (j = 0; j < NAPI_POLL_WEIGHT; j++)
|
|
{
|
|
tx_desc = PCH_GBE_TX_DESC(*tx_ring, k);
|
|
if (tx_desc->gbec_status != DSC_INIT16) break; /*found*/
|
|
if (++k >= tx_ring->count) k = 0; /*increment, wrap*/
|
|
}
|
|
if (j < NAPI_POLL_WEIGHT) {
|
|
netdev_dbg(adapter->netdev,
|
|
"clean_tx: unused=%d loops=%d found tx_desc[%x,%x:%x].gbec_status=%04x\n",
|
|
unused, j, i, k, tx_ring->next_to_use,
|
|
tx_desc->gbec_status);
|
|
i = k; /*found one to clean, usu gbec_status==2000.*/
|
|
}
|
|
}
|
|
|
|
while ((tx_desc->gbec_status & DSC_INIT16) == 0x0000) {
|
|
netdev_dbg(adapter->netdev, "gbec_status:0x%04x\n",
|
|
tx_desc->gbec_status);
|
|
buffer_info = &tx_ring->buffer_info[i];
|
|
skb = buffer_info->skb;
|
|
cleaned = true;
|
|
|
|
if ((tx_desc->gbec_status & PCH_GBE_TXD_GMAC_STAT_ABT)) {
|
|
adapter->stats.tx_aborted_errors++;
|
|
netdev_err(adapter->netdev, "Transfer Abort Error\n");
|
|
} else if ((tx_desc->gbec_status & PCH_GBE_TXD_GMAC_STAT_CRSER)
|
|
) {
|
|
adapter->stats.tx_carrier_errors++;
|
|
netdev_err(adapter->netdev,
|
|
"Transfer Carrier Sense Error\n");
|
|
} else if ((tx_desc->gbec_status & PCH_GBE_TXD_GMAC_STAT_EXCOL)
|
|
) {
|
|
adapter->stats.tx_aborted_errors++;
|
|
netdev_err(adapter->netdev,
|
|
"Transfer Collision Abort Error\n");
|
|
} else if ((tx_desc->gbec_status &
|
|
(PCH_GBE_TXD_GMAC_STAT_SNGCOL |
|
|
PCH_GBE_TXD_GMAC_STAT_MLTCOL))) {
|
|
adapter->stats.collisions++;
|
|
adapter->stats.tx_packets++;
|
|
adapter->stats.tx_bytes += skb->len;
|
|
netdev_dbg(adapter->netdev, "Transfer Collision\n");
|
|
} else if ((tx_desc->gbec_status & PCH_GBE_TXD_GMAC_STAT_CMPLT)
|
|
) {
|
|
adapter->stats.tx_packets++;
|
|
adapter->stats.tx_bytes += skb->len;
|
|
}
|
|
if (buffer_info->mapped) {
|
|
netdev_dbg(adapter->netdev,
|
|
"unmap buffer_info->dma : %d\n", i);
|
|
dma_unmap_single(&adapter->pdev->dev, buffer_info->dma,
|
|
buffer_info->length, DMA_TO_DEVICE);
|
|
buffer_info->mapped = false;
|
|
}
|
|
if (buffer_info->skb) {
|
|
netdev_dbg(adapter->netdev,
|
|
"trim buffer_info->skb : %d\n", i);
|
|
skb_trim(buffer_info->skb, 0);
|
|
}
|
|
tx_desc->gbec_status = DSC_INIT16;
|
|
if (unlikely(++i == tx_ring->count))
|
|
i = 0;
|
|
tx_desc = PCH_GBE_TX_DESC(*tx_ring, i);
|
|
|
|
/* weight of a sort for tx, to avoid endless transmit cleanup */
|
|
if (cleaned_count++ == NAPI_POLL_WEIGHT) {
|
|
cleaned = false;
|
|
break;
|
|
}
|
|
}
|
|
netdev_dbg(adapter->netdev,
|
|
"called pch_gbe_unmap_and_free_tx_resource() %d count\n",
|
|
cleaned_count);
|
|
if (cleaned_count > 0) { /*skip this if nothing cleaned*/
|
|
/* Recover from running out of Tx resources in xmit_frame */
|
|
netif_tx_lock(adapter->netdev);
|
|
if (unlikely(cleaned && (netif_queue_stopped(adapter->netdev))))
|
|
{
|
|
netif_wake_queue(adapter->netdev);
|
|
adapter->stats.tx_restart_count++;
|
|
netdev_dbg(adapter->netdev, "Tx wake queue\n");
|
|
}
|
|
|
|
tx_ring->next_to_clean = i;
|
|
|
|
netdev_dbg(adapter->netdev, "next_to_clean : %d\n",
|
|
tx_ring->next_to_clean);
|
|
netif_tx_unlock(adapter->netdev);
|
|
}
|
|
return cleaned;
|
|
}
|
|
|
|
/**
|
|
* pch_gbe_clean_rx - Send received data up the network stack; legacy
|
|
* @adapter: Board private structure
|
|
* @rx_ring: Rx descriptor ring
|
|
* @work_done: Completed count
|
|
* @work_to_do: Request count
|
|
* Returns:
|
|
* true: Cleaned the descriptor
|
|
* false: Not cleaned the descriptor
|
|
*/
|
|
static bool
|
|
pch_gbe_clean_rx(struct pch_gbe_adapter *adapter,
|
|
struct pch_gbe_rx_ring *rx_ring,
|
|
int *work_done, int work_to_do)
|
|
{
|
|
struct net_device *netdev = adapter->netdev;
|
|
struct pci_dev *pdev = adapter->pdev;
|
|
struct pch_gbe_buffer *buffer_info;
|
|
struct pch_gbe_rx_desc *rx_desc;
|
|
u32 length;
|
|
unsigned int i;
|
|
unsigned int cleaned_count = 0;
|
|
bool cleaned = false;
|
|
struct sk_buff *skb;
|
|
u8 dma_status;
|
|
u16 gbec_status;
|
|
u32 tcp_ip_status;
|
|
|
|
i = rx_ring->next_to_clean;
|
|
|
|
while (*work_done < work_to_do) {
|
|
/* Check Rx descriptor status */
|
|
rx_desc = PCH_GBE_RX_DESC(*rx_ring, i);
|
|
if (rx_desc->gbec_status == DSC_INIT16)
|
|
break;
|
|
cleaned = true;
|
|
cleaned_count++;
|
|
|
|
dma_status = rx_desc->dma_status;
|
|
gbec_status = rx_desc->gbec_status;
|
|
tcp_ip_status = rx_desc->tcp_ip_status;
|
|
rx_desc->gbec_status = DSC_INIT16;
|
|
buffer_info = &rx_ring->buffer_info[i];
|
|
skb = buffer_info->skb;
|
|
buffer_info->skb = NULL;
|
|
|
|
/* unmap dma */
|
|
dma_unmap_single(&pdev->dev, buffer_info->dma,
|
|
buffer_info->length, DMA_FROM_DEVICE);
|
|
buffer_info->mapped = false;
|
|
|
|
netdev_dbg(netdev,
|
|
"RxDecNo = 0x%04x Status[DMA:0x%02x GBE:0x%04x TCP:0x%08x] BufInf = 0x%p\n",
|
|
i, dma_status, gbec_status, tcp_ip_status,
|
|
buffer_info);
|
|
/* Error check */
|
|
if (unlikely(gbec_status & PCH_GBE_RXD_GMAC_STAT_NOTOCTAL)) {
|
|
adapter->stats.rx_frame_errors++;
|
|
netdev_err(netdev, "Receive Not Octal Error\n");
|
|
} else if (unlikely(gbec_status &
|
|
PCH_GBE_RXD_GMAC_STAT_NBLERR)) {
|
|
adapter->stats.rx_frame_errors++;
|
|
netdev_err(netdev, "Receive Nibble Error\n");
|
|
} else if (unlikely(gbec_status &
|
|
PCH_GBE_RXD_GMAC_STAT_CRCERR)) {
|
|
adapter->stats.rx_crc_errors++;
|
|
netdev_err(netdev, "Receive CRC Error\n");
|
|
} else {
|
|
/* get receive length */
|
|
/* length convert[-3], length includes FCS length */
|
|
length = (rx_desc->rx_words_eob) - 3 - ETH_FCS_LEN;
|
|
if (rx_desc->rx_words_eob & 0x02)
|
|
length = length - 4;
|
|
/*
|
|
* buffer_info->rx_buffer: [Header:14][payload]
|
|
* skb->data: [Reserve:2][Header:14][payload]
|
|
*/
|
|
memcpy(skb->data, buffer_info->rx_buffer, length);
|
|
|
|
/* update status of driver */
|
|
adapter->stats.rx_bytes += length;
|
|
adapter->stats.rx_packets++;
|
|
if ((gbec_status & PCH_GBE_RXD_GMAC_STAT_MARMLT))
|
|
adapter->stats.multicast++;
|
|
/* Write meta date of skb */
|
|
skb_put(skb, length);
|
|
|
|
pch_rx_timestamp(adapter, skb);
|
|
|
|
skb->protocol = eth_type_trans(skb, netdev);
|
|
if (tcp_ip_status & PCH_GBE_RXD_ACC_STAT_TCPIPOK)
|
|
skb->ip_summed = CHECKSUM_UNNECESSARY;
|
|
else
|
|
skb->ip_summed = CHECKSUM_NONE;
|
|
|
|
napi_gro_receive(&adapter->napi, skb);
|
|
(*work_done)++;
|
|
netdev_dbg(netdev,
|
|
"Receive skb->ip_summed: %d length: %d\n",
|
|
skb->ip_summed, length);
|
|
}
|
|
/* return some buffers to hardware, one at a time is too slow */
|
|
if (unlikely(cleaned_count >= PCH_GBE_RX_BUFFER_WRITE)) {
|
|
pch_gbe_alloc_rx_buffers(adapter, rx_ring,
|
|
cleaned_count);
|
|
cleaned_count = 0;
|
|
}
|
|
if (++i == rx_ring->count)
|
|
i = 0;
|
|
}
|
|
rx_ring->next_to_clean = i;
|
|
if (cleaned_count)
|
|
pch_gbe_alloc_rx_buffers(adapter, rx_ring, cleaned_count);
|
|
return cleaned;
|
|
}
|
|
|
|
/**
|
|
* pch_gbe_setup_tx_resources - Allocate Tx resources (Descriptors)
|
|
* @adapter: Board private structure
|
|
* @tx_ring: Tx descriptor ring (for a specific queue) to setup
|
|
* Returns:
|
|
* 0: Successfully
|
|
* Negative value: Failed
|
|
*/
|
|
int pch_gbe_setup_tx_resources(struct pch_gbe_adapter *adapter,
|
|
struct pch_gbe_tx_ring *tx_ring)
|
|
{
|
|
struct pci_dev *pdev = adapter->pdev;
|
|
struct pch_gbe_tx_desc *tx_desc;
|
|
int size;
|
|
int desNo;
|
|
|
|
size = (int)sizeof(struct pch_gbe_buffer) * tx_ring->count;
|
|
tx_ring->buffer_info = vzalloc(size);
|
|
if (!tx_ring->buffer_info)
|
|
return -ENOMEM;
|
|
|
|
tx_ring->size = tx_ring->count * (int)sizeof(struct pch_gbe_tx_desc);
|
|
|
|
tx_ring->desc = dma_alloc_coherent(&pdev->dev, tx_ring->size,
|
|
&tx_ring->dma, GFP_KERNEL);
|
|
if (!tx_ring->desc) {
|
|
vfree(tx_ring->buffer_info);
|
|
return -ENOMEM;
|
|
}
|
|
|
|
tx_ring->next_to_use = 0;
|
|
tx_ring->next_to_clean = 0;
|
|
|
|
for (desNo = 0; desNo < tx_ring->count; desNo++) {
|
|
tx_desc = PCH_GBE_TX_DESC(*tx_ring, desNo);
|
|
tx_desc->gbec_status = DSC_INIT16;
|
|
}
|
|
netdev_dbg(adapter->netdev,
|
|
"tx_ring->desc = 0x%p tx_ring->dma = 0x%08llx next_to_clean = 0x%08x next_to_use = 0x%08x\n",
|
|
tx_ring->desc, (unsigned long long)tx_ring->dma,
|
|
tx_ring->next_to_clean, tx_ring->next_to_use);
|
|
return 0;
|
|
}
|
|
|
|
/**
|
|
* pch_gbe_setup_rx_resources - Allocate Rx resources (Descriptors)
|
|
* @adapter: Board private structure
|
|
* @rx_ring: Rx descriptor ring (for a specific queue) to setup
|
|
* Returns:
|
|
* 0: Successfully
|
|
* Negative value: Failed
|
|
*/
|
|
int pch_gbe_setup_rx_resources(struct pch_gbe_adapter *adapter,
|
|
struct pch_gbe_rx_ring *rx_ring)
|
|
{
|
|
struct pci_dev *pdev = adapter->pdev;
|
|
struct pch_gbe_rx_desc *rx_desc;
|
|
int size;
|
|
int desNo;
|
|
|
|
size = (int)sizeof(struct pch_gbe_buffer) * rx_ring->count;
|
|
rx_ring->buffer_info = vzalloc(size);
|
|
if (!rx_ring->buffer_info)
|
|
return -ENOMEM;
|
|
|
|
rx_ring->size = rx_ring->count * (int)sizeof(struct pch_gbe_rx_desc);
|
|
rx_ring->desc = dma_alloc_coherent(&pdev->dev, rx_ring->size,
|
|
&rx_ring->dma, GFP_KERNEL);
|
|
if (!rx_ring->desc) {
|
|
vfree(rx_ring->buffer_info);
|
|
return -ENOMEM;
|
|
}
|
|
rx_ring->next_to_clean = 0;
|
|
rx_ring->next_to_use = 0;
|
|
for (desNo = 0; desNo < rx_ring->count; desNo++) {
|
|
rx_desc = PCH_GBE_RX_DESC(*rx_ring, desNo);
|
|
rx_desc->gbec_status = DSC_INIT16;
|
|
}
|
|
netdev_dbg(adapter->netdev,
|
|
"rx_ring->desc = 0x%p rx_ring->dma = 0x%08llx next_to_clean = 0x%08x next_to_use = 0x%08x\n",
|
|
rx_ring->desc, (unsigned long long)rx_ring->dma,
|
|
rx_ring->next_to_clean, rx_ring->next_to_use);
|
|
return 0;
|
|
}
|
|
|
|
/**
|
|
* pch_gbe_free_tx_resources - Free Tx Resources
|
|
* @adapter: Board private structure
|
|
* @tx_ring: Tx descriptor ring for a specific queue
|
|
*/
|
|
void pch_gbe_free_tx_resources(struct pch_gbe_adapter *adapter,
|
|
struct pch_gbe_tx_ring *tx_ring)
|
|
{
|
|
struct pci_dev *pdev = adapter->pdev;
|
|
|
|
pch_gbe_clean_tx_ring(adapter, tx_ring);
|
|
vfree(tx_ring->buffer_info);
|
|
tx_ring->buffer_info = NULL;
|
|
dma_free_coherent(&pdev->dev, tx_ring->size, tx_ring->desc,
|
|
tx_ring->dma);
|
|
tx_ring->desc = NULL;
|
|
}
|
|
|
|
/**
|
|
* pch_gbe_free_rx_resources - Free Rx Resources
|
|
* @adapter: Board private structure
|
|
* @rx_ring: Ring to clean the resources from
|
|
*/
|
|
void pch_gbe_free_rx_resources(struct pch_gbe_adapter *adapter,
|
|
struct pch_gbe_rx_ring *rx_ring)
|
|
{
|
|
struct pci_dev *pdev = adapter->pdev;
|
|
|
|
pch_gbe_clean_rx_ring(adapter, rx_ring);
|
|
vfree(rx_ring->buffer_info);
|
|
rx_ring->buffer_info = NULL;
|
|
dma_free_coherent(&pdev->dev, rx_ring->size, rx_ring->desc,
|
|
rx_ring->dma);
|
|
rx_ring->desc = NULL;
|
|
}
|
|
|
|
/**
|
|
* pch_gbe_request_irq - Allocate an interrupt line
|
|
* @adapter: Board private structure
|
|
* Returns:
|
|
* 0: Successfully
|
|
* Negative value: Failed
|
|
*/
|
|
static int pch_gbe_request_irq(struct pch_gbe_adapter *adapter)
|
|
{
|
|
struct net_device *netdev = adapter->netdev;
|
|
int err;
|
|
|
|
err = pci_alloc_irq_vectors(adapter->pdev, 1, 1, PCI_IRQ_ALL_TYPES);
|
|
if (err < 0)
|
|
return err;
|
|
|
|
adapter->irq = pci_irq_vector(adapter->pdev, 0);
|
|
|
|
err = request_irq(adapter->irq, &pch_gbe_intr, IRQF_SHARED,
|
|
netdev->name, netdev);
|
|
if (err)
|
|
netdev_err(netdev, "Unable to allocate interrupt Error: %d\n",
|
|
err);
|
|
netdev_dbg(netdev, "have_msi : %d return : 0x%04x\n",
|
|
pci_dev_msi_enabled(adapter->pdev), err);
|
|
return err;
|
|
}
|
|
|
|
/**
|
|
* pch_gbe_up - Up GbE network device
|
|
* @adapter: Board private structure
|
|
* Returns:
|
|
* 0: Successfully
|
|
* Negative value: Failed
|
|
*/
|
|
int pch_gbe_up(struct pch_gbe_adapter *adapter)
|
|
{
|
|
struct net_device *netdev = adapter->netdev;
|
|
struct pch_gbe_tx_ring *tx_ring = adapter->tx_ring;
|
|
struct pch_gbe_rx_ring *rx_ring = adapter->rx_ring;
|
|
int err = -EINVAL;
|
|
|
|
/* Ensure we have a valid MAC */
|
|
if (!is_valid_ether_addr(adapter->hw.mac.addr)) {
|
|
netdev_err(netdev, "Error: Invalid MAC address\n");
|
|
goto out;
|
|
}
|
|
|
|
/* hardware has been reset, we need to reload some things */
|
|
pch_gbe_set_multi(netdev);
|
|
|
|
pch_gbe_setup_tctl(adapter);
|
|
pch_gbe_configure_tx(adapter);
|
|
pch_gbe_setup_rctl(adapter);
|
|
pch_gbe_configure_rx(adapter);
|
|
|
|
err = pch_gbe_request_irq(adapter);
|
|
if (err) {
|
|
netdev_err(netdev,
|
|
"Error: can't bring device up - irq request failed\n");
|
|
goto out;
|
|
}
|
|
err = pch_gbe_alloc_rx_buffers_pool(adapter, rx_ring, rx_ring->count);
|
|
if (err) {
|
|
netdev_err(netdev,
|
|
"Error: can't bring device up - alloc rx buffers pool failed\n");
|
|
goto freeirq;
|
|
}
|
|
pch_gbe_alloc_tx_buffers(adapter, tx_ring);
|
|
pch_gbe_alloc_rx_buffers(adapter, rx_ring, rx_ring->count);
|
|
adapter->tx_queue_len = netdev->tx_queue_len;
|
|
pch_gbe_enable_dma_rx(&adapter->hw);
|
|
pch_gbe_enable_mac_rx(&adapter->hw);
|
|
|
|
mod_timer(&adapter->watchdog_timer, jiffies);
|
|
|
|
napi_enable(&adapter->napi);
|
|
pch_gbe_irq_enable(adapter);
|
|
netif_start_queue(adapter->netdev);
|
|
|
|
return 0;
|
|
|
|
freeirq:
|
|
pch_gbe_free_irq(adapter);
|
|
out:
|
|
return err;
|
|
}
|
|
|
|
/**
|
|
* pch_gbe_down - Down GbE network device
|
|
* @adapter: Board private structure
|
|
*/
|
|
void pch_gbe_down(struct pch_gbe_adapter *adapter)
|
|
{
|
|
struct net_device *netdev = adapter->netdev;
|
|
struct pci_dev *pdev = adapter->pdev;
|
|
struct pch_gbe_rx_ring *rx_ring = adapter->rx_ring;
|
|
|
|
/* signal that we're down so the interrupt handler does not
|
|
* reschedule our watchdog timer */
|
|
napi_disable(&adapter->napi);
|
|
atomic_set(&adapter->irq_sem, 0);
|
|
|
|
pch_gbe_irq_disable(adapter);
|
|
pch_gbe_free_irq(adapter);
|
|
|
|
del_timer_sync(&adapter->watchdog_timer);
|
|
|
|
netdev->tx_queue_len = adapter->tx_queue_len;
|
|
netif_carrier_off(netdev);
|
|
netif_stop_queue(netdev);
|
|
|
|
if ((pdev->error_state) && (pdev->error_state != pci_channel_io_normal))
|
|
pch_gbe_reset(adapter);
|
|
pch_gbe_clean_tx_ring(adapter, adapter->tx_ring);
|
|
pch_gbe_clean_rx_ring(adapter, adapter->rx_ring);
|
|
|
|
dma_free_coherent(&adapter->pdev->dev, rx_ring->rx_buff_pool_size,
|
|
rx_ring->rx_buff_pool, rx_ring->rx_buff_pool_logic);
|
|
rx_ring->rx_buff_pool_logic = 0;
|
|
rx_ring->rx_buff_pool_size = 0;
|
|
rx_ring->rx_buff_pool = NULL;
|
|
}
|
|
|
|
/**
|
|
* pch_gbe_sw_init - Initialize general software structures (struct pch_gbe_adapter)
|
|
* @adapter: Board private structure to initialize
|
|
* Returns:
|
|
* 0: Successfully
|
|
* Negative value: Failed
|
|
*/
|
|
static int pch_gbe_sw_init(struct pch_gbe_adapter *adapter)
|
|
{
|
|
struct pch_gbe_hw *hw = &adapter->hw;
|
|
struct net_device *netdev = adapter->netdev;
|
|
|
|
adapter->rx_buffer_len = PCH_GBE_FRAME_SIZE_2048;
|
|
hw->mac.max_frame_size = netdev->mtu + ETH_HLEN + ETH_FCS_LEN;
|
|
hw->mac.min_frame_size = ETH_ZLEN + ETH_FCS_LEN;
|
|
hw->phy.reset_delay_us = PCH_GBE_PHY_RESET_DELAY_US;
|
|
|
|
if (pch_gbe_alloc_queues(adapter)) {
|
|
netdev_err(netdev, "Unable to allocate memory for queues\n");
|
|
return -ENOMEM;
|
|
}
|
|
spin_lock_init(&adapter->hw.miim_lock);
|
|
spin_lock_init(&adapter->stats_lock);
|
|
spin_lock_init(&adapter->ethtool_lock);
|
|
atomic_set(&adapter->irq_sem, 0);
|
|
pch_gbe_irq_disable(adapter);
|
|
|
|
pch_gbe_init_stats(adapter);
|
|
|
|
netdev_dbg(netdev,
|
|
"rx_buffer_len : %d mac.min_frame_size : %d mac.max_frame_size : %d\n",
|
|
(u32) adapter->rx_buffer_len,
|
|
hw->mac.min_frame_size, hw->mac.max_frame_size);
|
|
return 0;
|
|
}
|
|
|
|
/**
|
|
* pch_gbe_open - Called when a network interface is made active
|
|
* @netdev: Network interface device structure
|
|
* Returns:
|
|
* 0: Successfully
|
|
* Negative value: Failed
|
|
*/
|
|
static int pch_gbe_open(struct net_device *netdev)
|
|
{
|
|
struct pch_gbe_adapter *adapter = netdev_priv(netdev);
|
|
struct pch_gbe_hw *hw = &adapter->hw;
|
|
int err;
|
|
|
|
/* allocate transmit descriptors */
|
|
err = pch_gbe_setup_tx_resources(adapter, adapter->tx_ring);
|
|
if (err)
|
|
goto err_setup_tx;
|
|
/* allocate receive descriptors */
|
|
err = pch_gbe_setup_rx_resources(adapter, adapter->rx_ring);
|
|
if (err)
|
|
goto err_setup_rx;
|
|
pch_gbe_phy_power_up(hw);
|
|
err = pch_gbe_up(adapter);
|
|
if (err)
|
|
goto err_up;
|
|
netdev_dbg(netdev, "Success End\n");
|
|
return 0;
|
|
|
|
err_up:
|
|
if (!adapter->wake_up_evt)
|
|
pch_gbe_phy_power_down(hw);
|
|
pch_gbe_free_rx_resources(adapter, adapter->rx_ring);
|
|
err_setup_rx:
|
|
pch_gbe_free_tx_resources(adapter, adapter->tx_ring);
|
|
err_setup_tx:
|
|
pch_gbe_reset(adapter);
|
|
netdev_err(netdev, "Error End\n");
|
|
return err;
|
|
}
|
|
|
|
/**
|
|
* pch_gbe_stop - Disables a network interface
|
|
* @netdev: Network interface device structure
|
|
* Returns:
|
|
* 0: Successfully
|
|
*/
|
|
static int pch_gbe_stop(struct net_device *netdev)
|
|
{
|
|
struct pch_gbe_adapter *adapter = netdev_priv(netdev);
|
|
struct pch_gbe_hw *hw = &adapter->hw;
|
|
|
|
pch_gbe_down(adapter);
|
|
if (!adapter->wake_up_evt)
|
|
pch_gbe_phy_power_down(hw);
|
|
pch_gbe_free_tx_resources(adapter, adapter->tx_ring);
|
|
pch_gbe_free_rx_resources(adapter, adapter->rx_ring);
|
|
return 0;
|
|
}
|
|
|
|
/**
|
|
* pch_gbe_xmit_frame - Packet transmitting start
|
|
* @skb: Socket buffer structure
|
|
* @netdev: Network interface device structure
|
|
* Returns:
|
|
* - NETDEV_TX_OK: Normal end
|
|
* - NETDEV_TX_BUSY: Error end
|
|
*/
|
|
static netdev_tx_t pch_gbe_xmit_frame(struct sk_buff *skb, struct net_device *netdev)
|
|
{
|
|
struct pch_gbe_adapter *adapter = netdev_priv(netdev);
|
|
struct pch_gbe_tx_ring *tx_ring = adapter->tx_ring;
|
|
|
|
if (unlikely(!PCH_GBE_DESC_UNUSED(tx_ring))) {
|
|
netif_stop_queue(netdev);
|
|
netdev_dbg(netdev,
|
|
"Return : BUSY next_to use : 0x%08x next_to clean : 0x%08x\n",
|
|
tx_ring->next_to_use, tx_ring->next_to_clean);
|
|
return NETDEV_TX_BUSY;
|
|
}
|
|
|
|
/* CRC,ITAG no support */
|
|
pch_gbe_tx_queue(adapter, tx_ring, skb);
|
|
return NETDEV_TX_OK;
|
|
}
|
|
|
|
/**
|
|
* pch_gbe_set_multi - Multicast and Promiscuous mode set
|
|
* @netdev: Network interface device structure
|
|
*/
|
|
static void pch_gbe_set_multi(struct net_device *netdev)
|
|
{
|
|
struct pch_gbe_adapter *adapter = netdev_priv(netdev);
|
|
struct pch_gbe_hw *hw = &adapter->hw;
|
|
struct netdev_hw_addr *ha;
|
|
u32 rctl, adrmask;
|
|
int mc_count, i;
|
|
|
|
netdev_dbg(netdev, "netdev->flags : 0x%08x\n", netdev->flags);
|
|
|
|
/* By default enable address & multicast filtering */
|
|
rctl = ioread32(&hw->reg->RX_MODE);
|
|
rctl |= PCH_GBE_ADD_FIL_EN | PCH_GBE_MLT_FIL_EN;
|
|
|
|
/* Promiscuous mode disables all hardware address filtering */
|
|
if (netdev->flags & IFF_PROMISC)
|
|
rctl &= ~(PCH_GBE_ADD_FIL_EN | PCH_GBE_MLT_FIL_EN);
|
|
|
|
/* If we want to monitor more multicast addresses than the hardware can
|
|
* support then disable hardware multicast filtering.
|
|
*/
|
|
mc_count = netdev_mc_count(netdev);
|
|
if ((netdev->flags & IFF_ALLMULTI) || mc_count >= PCH_GBE_MAR_ENTRIES)
|
|
rctl &= ~PCH_GBE_MLT_FIL_EN;
|
|
|
|
iowrite32(rctl, &hw->reg->RX_MODE);
|
|
|
|
/* If we're not using multicast filtering then there's no point
|
|
* configuring the unused MAC address registers.
|
|
*/
|
|
if (!(rctl & PCH_GBE_MLT_FIL_EN))
|
|
return;
|
|
|
|
/* Load the first set of multicast addresses into MAC address registers
|
|
* for use by hardware filtering.
|
|
*/
|
|
i = 1;
|
|
netdev_for_each_mc_addr(ha, netdev)
|
|
pch_gbe_mac_mar_set(hw, ha->addr, i++);
|
|
|
|
/* If there are spare MAC registers, mask & clear them */
|
|
for (; i < PCH_GBE_MAR_ENTRIES; i++) {
|
|
/* Clear MAC address mask */
|
|
adrmask = ioread32(&hw->reg->ADDR_MASK);
|
|
iowrite32(adrmask | BIT(i), &hw->reg->ADDR_MASK);
|
|
/* wait busy */
|
|
pch_gbe_wait_clr_bit(&hw->reg->ADDR_MASK, PCH_GBE_BUSY);
|
|
/* Clear MAC address */
|
|
iowrite32(0, &hw->reg->mac_adr[i].high);
|
|
iowrite32(0, &hw->reg->mac_adr[i].low);
|
|
}
|
|
|
|
netdev_dbg(netdev,
|
|
"RX_MODE reg(check bit31,30 ADD,MLT) : 0x%08x netdev->mc_count : 0x%08x\n",
|
|
ioread32(&hw->reg->RX_MODE), mc_count);
|
|
}
|
|
|
|
/**
|
|
* pch_gbe_set_mac - Change the Ethernet Address of the NIC
|
|
* @netdev: Network interface device structure
|
|
* @addr: Pointer to an address structure
|
|
* Returns:
|
|
* 0: Successfully
|
|
* -EADDRNOTAVAIL: Failed
|
|
*/
|
|
static int pch_gbe_set_mac(struct net_device *netdev, void *addr)
|
|
{
|
|
struct pch_gbe_adapter *adapter = netdev_priv(netdev);
|
|
struct sockaddr *skaddr = addr;
|
|
int ret_val;
|
|
|
|
if (!is_valid_ether_addr(skaddr->sa_data)) {
|
|
ret_val = -EADDRNOTAVAIL;
|
|
} else {
|
|
eth_hw_addr_set(netdev, skaddr->sa_data);
|
|
memcpy(adapter->hw.mac.addr, skaddr->sa_data, netdev->addr_len);
|
|
pch_gbe_mac_mar_set(&adapter->hw, adapter->hw.mac.addr, 0);
|
|
ret_val = 0;
|
|
}
|
|
netdev_dbg(netdev, "ret_val : 0x%08x\n", ret_val);
|
|
netdev_dbg(netdev, "dev_addr : %pM\n", netdev->dev_addr);
|
|
netdev_dbg(netdev, "mac_addr : %pM\n", adapter->hw.mac.addr);
|
|
netdev_dbg(netdev, "MAC_ADR1AB reg : 0x%08x 0x%08x\n",
|
|
ioread32(&adapter->hw.reg->mac_adr[0].high),
|
|
ioread32(&adapter->hw.reg->mac_adr[0].low));
|
|
return ret_val;
|
|
}
|
|
|
|
/**
|
|
* pch_gbe_change_mtu - Change the Maximum Transfer Unit
|
|
* @netdev: Network interface device structure
|
|
* @new_mtu: New value for maximum frame size
|
|
* Returns:
|
|
* 0: Successfully
|
|
* -EINVAL: Failed
|
|
*/
|
|
static int pch_gbe_change_mtu(struct net_device *netdev, int new_mtu)
|
|
{
|
|
struct pch_gbe_adapter *adapter = netdev_priv(netdev);
|
|
int max_frame = new_mtu + ETH_HLEN + ETH_FCS_LEN;
|
|
unsigned long old_rx_buffer_len = adapter->rx_buffer_len;
|
|
int err;
|
|
|
|
if (max_frame <= PCH_GBE_FRAME_SIZE_2048)
|
|
adapter->rx_buffer_len = PCH_GBE_FRAME_SIZE_2048;
|
|
else if (max_frame <= PCH_GBE_FRAME_SIZE_4096)
|
|
adapter->rx_buffer_len = PCH_GBE_FRAME_SIZE_4096;
|
|
else if (max_frame <= PCH_GBE_FRAME_SIZE_8192)
|
|
adapter->rx_buffer_len = PCH_GBE_FRAME_SIZE_8192;
|
|
else
|
|
adapter->rx_buffer_len = PCH_GBE_MAX_RX_BUFFER_SIZE;
|
|
|
|
if (netif_running(netdev)) {
|
|
pch_gbe_down(adapter);
|
|
err = pch_gbe_up(adapter);
|
|
if (err) {
|
|
adapter->rx_buffer_len = old_rx_buffer_len;
|
|
pch_gbe_up(adapter);
|
|
return err;
|
|
} else {
|
|
netdev->mtu = new_mtu;
|
|
adapter->hw.mac.max_frame_size = max_frame;
|
|
}
|
|
} else {
|
|
pch_gbe_reset(adapter);
|
|
netdev->mtu = new_mtu;
|
|
adapter->hw.mac.max_frame_size = max_frame;
|
|
}
|
|
|
|
netdev_dbg(netdev,
|
|
"max_frame : %d rx_buffer_len : %d mtu : %d max_frame_size : %d\n",
|
|
max_frame, (u32) adapter->rx_buffer_len, netdev->mtu,
|
|
adapter->hw.mac.max_frame_size);
|
|
return 0;
|
|
}
|
|
|
|
/**
|
|
* pch_gbe_set_features - Reset device after features changed
|
|
* @netdev: Network interface device structure
|
|
* @features: New features
|
|
* Returns:
|
|
* 0: HW state updated successfully
|
|
*/
|
|
static int pch_gbe_set_features(struct net_device *netdev,
|
|
netdev_features_t features)
|
|
{
|
|
struct pch_gbe_adapter *adapter = netdev_priv(netdev);
|
|
netdev_features_t changed = features ^ netdev->features;
|
|
|
|
if (!(changed & NETIF_F_RXCSUM))
|
|
return 0;
|
|
|
|
if (netif_running(netdev))
|
|
pch_gbe_reinit_locked(adapter);
|
|
else
|
|
pch_gbe_reset(adapter);
|
|
|
|
return 0;
|
|
}
|
|
|
|
/**
|
|
* pch_gbe_ioctl - Controls register through a MII interface
|
|
* @netdev: Network interface device structure
|
|
* @ifr: Pointer to ifr structure
|
|
* @cmd: Control command
|
|
* Returns:
|
|
* 0: Successfully
|
|
* Negative value: Failed
|
|
*/
|
|
static int pch_gbe_ioctl(struct net_device *netdev, struct ifreq *ifr, int cmd)
|
|
{
|
|
struct pch_gbe_adapter *adapter = netdev_priv(netdev);
|
|
|
|
netdev_dbg(netdev, "cmd : 0x%04x\n", cmd);
|
|
|
|
if (cmd == SIOCSHWTSTAMP)
|
|
return hwtstamp_ioctl(netdev, ifr, cmd);
|
|
|
|
return generic_mii_ioctl(&adapter->mii, if_mii(ifr), cmd, NULL);
|
|
}
|
|
|
|
/**
|
|
* pch_gbe_tx_timeout - Respond to a Tx Hang
|
|
* @netdev: Network interface device structure
|
|
* @txqueue: index of hanging queue
|
|
*/
|
|
static void pch_gbe_tx_timeout(struct net_device *netdev, unsigned int txqueue)
|
|
{
|
|
struct pch_gbe_adapter *adapter = netdev_priv(netdev);
|
|
|
|
/* Do the reset outside of interrupt context */
|
|
adapter->stats.tx_timeout_count++;
|
|
schedule_work(&adapter->reset_task);
|
|
}
|
|
|
|
/**
|
|
* pch_gbe_napi_poll - NAPI receive and transfer polling callback
|
|
* @napi: Pointer of polling device struct
|
|
* @budget: The maximum number of a packet
|
|
* Returns:
|
|
* false: Exit the polling mode
|
|
* true: Continue the polling mode
|
|
*/
|
|
static int pch_gbe_napi_poll(struct napi_struct *napi, int budget)
|
|
{
|
|
struct pch_gbe_adapter *adapter =
|
|
container_of(napi, struct pch_gbe_adapter, napi);
|
|
int work_done = 0;
|
|
bool poll_end_flag = false;
|
|
bool cleaned = false;
|
|
|
|
netdev_dbg(adapter->netdev, "budget : %d\n", budget);
|
|
|
|
pch_gbe_clean_rx(adapter, adapter->rx_ring, &work_done, budget);
|
|
cleaned = pch_gbe_clean_tx(adapter, adapter->tx_ring);
|
|
|
|
if (cleaned)
|
|
work_done = budget;
|
|
/* If no Tx and not enough Rx work done,
|
|
* exit the polling mode
|
|
*/
|
|
if (work_done < budget)
|
|
poll_end_flag = true;
|
|
|
|
if (poll_end_flag) {
|
|
napi_complete_done(napi, work_done);
|
|
pch_gbe_irq_enable(adapter);
|
|
}
|
|
|
|
if (adapter->rx_stop_flag) {
|
|
adapter->rx_stop_flag = false;
|
|
pch_gbe_enable_dma_rx(&adapter->hw);
|
|
}
|
|
|
|
netdev_dbg(adapter->netdev,
|
|
"poll_end_flag : %d work_done : %d budget : %d\n",
|
|
poll_end_flag, work_done, budget);
|
|
|
|
return work_done;
|
|
}
|
|
|
|
#ifdef CONFIG_NET_POLL_CONTROLLER
|
|
/**
|
|
* pch_gbe_netpoll - Used by things like netconsole to send skbs
|
|
* @netdev: Network interface device structure
|
|
*/
|
|
static void pch_gbe_netpoll(struct net_device *netdev)
|
|
{
|
|
struct pch_gbe_adapter *adapter = netdev_priv(netdev);
|
|
|
|
disable_irq(adapter->irq);
|
|
pch_gbe_intr(adapter->irq, netdev);
|
|
enable_irq(adapter->irq);
|
|
}
|
|
#endif
|
|
|
|
static const struct net_device_ops pch_gbe_netdev_ops = {
|
|
.ndo_open = pch_gbe_open,
|
|
.ndo_stop = pch_gbe_stop,
|
|
.ndo_start_xmit = pch_gbe_xmit_frame,
|
|
.ndo_set_mac_address = pch_gbe_set_mac,
|
|
.ndo_tx_timeout = pch_gbe_tx_timeout,
|
|
.ndo_change_mtu = pch_gbe_change_mtu,
|
|
.ndo_set_features = pch_gbe_set_features,
|
|
.ndo_eth_ioctl = pch_gbe_ioctl,
|
|
.ndo_set_rx_mode = pch_gbe_set_multi,
|
|
#ifdef CONFIG_NET_POLL_CONTROLLER
|
|
.ndo_poll_controller = pch_gbe_netpoll,
|
|
#endif
|
|
};
|
|
|
|
static pci_ers_result_t pch_gbe_io_error_detected(struct pci_dev *pdev,
|
|
pci_channel_state_t state)
|
|
{
|
|
struct net_device *netdev = pci_get_drvdata(pdev);
|
|
struct pch_gbe_adapter *adapter = netdev_priv(netdev);
|
|
|
|
netif_device_detach(netdev);
|
|
if (netif_running(netdev))
|
|
pch_gbe_down(adapter);
|
|
pci_disable_device(pdev);
|
|
/* Request a slot slot reset. */
|
|
return PCI_ERS_RESULT_NEED_RESET;
|
|
}
|
|
|
|
static pci_ers_result_t pch_gbe_io_slot_reset(struct pci_dev *pdev)
|
|
{
|
|
struct net_device *netdev = pci_get_drvdata(pdev);
|
|
struct pch_gbe_adapter *adapter = netdev_priv(netdev);
|
|
struct pch_gbe_hw *hw = &adapter->hw;
|
|
|
|
if (pci_enable_device(pdev)) {
|
|
netdev_err(netdev, "Cannot re-enable PCI device after reset\n");
|
|
return PCI_ERS_RESULT_DISCONNECT;
|
|
}
|
|
pci_set_master(pdev);
|
|
pci_enable_wake(pdev, PCI_D0, 0);
|
|
pch_gbe_phy_power_up(hw);
|
|
pch_gbe_reset(adapter);
|
|
/* Clear wake up status */
|
|
pch_gbe_mac_set_wol_event(hw, 0);
|
|
|
|
return PCI_ERS_RESULT_RECOVERED;
|
|
}
|
|
|
|
static void pch_gbe_io_resume(struct pci_dev *pdev)
|
|
{
|
|
struct net_device *netdev = pci_get_drvdata(pdev);
|
|
struct pch_gbe_adapter *adapter = netdev_priv(netdev);
|
|
|
|
if (netif_running(netdev)) {
|
|
if (pch_gbe_up(adapter)) {
|
|
netdev_dbg(netdev,
|
|
"can't bring device back up after reset\n");
|
|
return;
|
|
}
|
|
}
|
|
netif_device_attach(netdev);
|
|
}
|
|
|
|
static int __pch_gbe_suspend(struct pci_dev *pdev)
|
|
{
|
|
struct net_device *netdev = pci_get_drvdata(pdev);
|
|
struct pch_gbe_adapter *adapter = netdev_priv(netdev);
|
|
struct pch_gbe_hw *hw = &adapter->hw;
|
|
u32 wufc = adapter->wake_up_evt;
|
|
|
|
netif_device_detach(netdev);
|
|
if (netif_running(netdev))
|
|
pch_gbe_down(adapter);
|
|
if (wufc) {
|
|
pch_gbe_set_multi(netdev);
|
|
pch_gbe_setup_rctl(adapter);
|
|
pch_gbe_configure_rx(adapter);
|
|
pch_gbe_set_rgmii_ctrl(adapter, hw->mac.link_speed,
|
|
hw->mac.link_duplex);
|
|
pch_gbe_set_mode(adapter, hw->mac.link_speed,
|
|
hw->mac.link_duplex);
|
|
pch_gbe_mac_set_wol_event(hw, wufc);
|
|
pci_disable_device(pdev);
|
|
} else {
|
|
pch_gbe_phy_power_down(hw);
|
|
pch_gbe_mac_set_wol_event(hw, wufc);
|
|
pci_disable_device(pdev);
|
|
}
|
|
return 0;
|
|
}
|
|
|
|
#ifdef CONFIG_PM
|
|
static int pch_gbe_suspend(struct device *device)
|
|
{
|
|
struct pci_dev *pdev = to_pci_dev(device);
|
|
|
|
return __pch_gbe_suspend(pdev);
|
|
}
|
|
|
|
static int pch_gbe_resume(struct device *device)
|
|
{
|
|
struct pci_dev *pdev = to_pci_dev(device);
|
|
struct net_device *netdev = pci_get_drvdata(pdev);
|
|
struct pch_gbe_adapter *adapter = netdev_priv(netdev);
|
|
struct pch_gbe_hw *hw = &adapter->hw;
|
|
u32 err;
|
|
|
|
err = pci_enable_device(pdev);
|
|
if (err) {
|
|
netdev_err(netdev, "Cannot enable PCI device from suspend\n");
|
|
return err;
|
|
}
|
|
pci_set_master(pdev);
|
|
pch_gbe_phy_power_up(hw);
|
|
pch_gbe_reset(adapter);
|
|
/* Clear wake on lan control and status */
|
|
pch_gbe_mac_set_wol_event(hw, 0);
|
|
|
|
if (netif_running(netdev))
|
|
pch_gbe_up(adapter);
|
|
netif_device_attach(netdev);
|
|
|
|
return 0;
|
|
}
|
|
#endif /* CONFIG_PM */
|
|
|
|
static void pch_gbe_shutdown(struct pci_dev *pdev)
|
|
{
|
|
__pch_gbe_suspend(pdev);
|
|
if (system_state == SYSTEM_POWER_OFF) {
|
|
pci_wake_from_d3(pdev, true);
|
|
pci_set_power_state(pdev, PCI_D3hot);
|
|
}
|
|
}
|
|
|
|
static void pch_gbe_remove(struct pci_dev *pdev)
|
|
{
|
|
struct net_device *netdev = pci_get_drvdata(pdev);
|
|
struct pch_gbe_adapter *adapter = netdev_priv(netdev);
|
|
|
|
cancel_work_sync(&adapter->reset_task);
|
|
unregister_netdev(netdev);
|
|
|
|
pch_gbe_phy_hw_reset(&adapter->hw);
|
|
pci_dev_put(adapter->ptp_pdev);
|
|
|
|
free_netdev(netdev);
|
|
}
|
|
|
|
static int pch_gbe_probe(struct pci_dev *pdev,
|
|
const struct pci_device_id *pci_id)
|
|
{
|
|
struct net_device *netdev;
|
|
struct pch_gbe_adapter *adapter;
|
|
int ret;
|
|
|
|
ret = pcim_enable_device(pdev);
|
|
if (ret)
|
|
return ret;
|
|
|
|
if (dma_set_mask_and_coherent(&pdev->dev, DMA_BIT_MASK(64))) {
|
|
ret = dma_set_mask_and_coherent(&pdev->dev, DMA_BIT_MASK(32));
|
|
if (ret) {
|
|
dev_err(&pdev->dev, "ERR: No usable DMA configuration, aborting\n");
|
|
return ret;
|
|
}
|
|
}
|
|
|
|
ret = pcim_iomap_regions(pdev, 1 << PCH_GBE_PCI_BAR, pci_name(pdev));
|
|
if (ret) {
|
|
dev_err(&pdev->dev,
|
|
"ERR: Can't reserve PCI I/O and memory resources\n");
|
|
return ret;
|
|
}
|
|
pci_set_master(pdev);
|
|
|
|
netdev = alloc_etherdev((int)sizeof(struct pch_gbe_adapter));
|
|
if (!netdev)
|
|
return -ENOMEM;
|
|
SET_NETDEV_DEV(netdev, &pdev->dev);
|
|
|
|
pci_set_drvdata(pdev, netdev);
|
|
adapter = netdev_priv(netdev);
|
|
adapter->netdev = netdev;
|
|
adapter->pdev = pdev;
|
|
adapter->hw.back = adapter;
|
|
adapter->hw.reg = pcim_iomap_table(pdev)[PCH_GBE_PCI_BAR];
|
|
|
|
adapter->pdata = (struct pch_gbe_privdata *)pci_id->driver_data;
|
|
if (adapter->pdata && adapter->pdata->platform_init) {
|
|
ret = adapter->pdata->platform_init(pdev);
|
|
if (ret)
|
|
goto err_free_netdev;
|
|
}
|
|
|
|
adapter->ptp_pdev =
|
|
pci_get_domain_bus_and_slot(pci_domain_nr(adapter->pdev->bus),
|
|
adapter->pdev->bus->number,
|
|
PCI_DEVFN(12, 4));
|
|
|
|
netdev->netdev_ops = &pch_gbe_netdev_ops;
|
|
netdev->watchdog_timeo = PCH_GBE_WATCHDOG_PERIOD;
|
|
netif_napi_add(netdev, &adapter->napi, pch_gbe_napi_poll);
|
|
netdev->hw_features = NETIF_F_RXCSUM |
|
|
NETIF_F_IP_CSUM | NETIF_F_IPV6_CSUM;
|
|
netdev->features = netdev->hw_features;
|
|
pch_gbe_set_ethtool_ops(netdev);
|
|
|
|
/* MTU range: 46 - 10300 */
|
|
netdev->min_mtu = ETH_ZLEN - ETH_HLEN;
|
|
netdev->max_mtu = PCH_GBE_MAX_JUMBO_FRAME_SIZE -
|
|
(ETH_HLEN + ETH_FCS_LEN);
|
|
|
|
pch_gbe_mac_load_mac_addr(&adapter->hw);
|
|
pch_gbe_mac_reset_hw(&adapter->hw);
|
|
|
|
/* setup the private structure */
|
|
ret = pch_gbe_sw_init(adapter);
|
|
if (ret)
|
|
goto err_put_dev;
|
|
|
|
/* Initialize PHY */
|
|
ret = pch_gbe_init_phy(adapter);
|
|
if (ret) {
|
|
dev_err(&pdev->dev, "PHY initialize error\n");
|
|
goto err_free_adapter;
|
|
}
|
|
|
|
/* Read the MAC address. and store to the private data */
|
|
ret = pch_gbe_mac_read_mac_addr(&adapter->hw);
|
|
if (ret) {
|
|
dev_err(&pdev->dev, "MAC address Read Error\n");
|
|
goto err_free_adapter;
|
|
}
|
|
|
|
eth_hw_addr_set(netdev, adapter->hw.mac.addr);
|
|
if (!is_valid_ether_addr(netdev->dev_addr)) {
|
|
/*
|
|
* If the MAC is invalid (or just missing), display a warning
|
|
* but do not abort setting up the device. pch_gbe_up will
|
|
* prevent the interface from being brought up until a valid MAC
|
|
* is set.
|
|
*/
|
|
dev_err(&pdev->dev, "Invalid MAC address, "
|
|
"interface disabled.\n");
|
|
}
|
|
timer_setup(&adapter->watchdog_timer, pch_gbe_watchdog, 0);
|
|
|
|
INIT_WORK(&adapter->reset_task, pch_gbe_reset_task);
|
|
|
|
pch_gbe_check_options(adapter);
|
|
|
|
/* initialize the wol settings based on the eeprom settings */
|
|
adapter->wake_up_evt = PCH_GBE_WL_INIT_SETTING;
|
|
dev_info(&pdev->dev, "MAC address : %pM\n", netdev->dev_addr);
|
|
|
|
/* reset the hardware with the new settings */
|
|
pch_gbe_reset(adapter);
|
|
|
|
ret = register_netdev(netdev);
|
|
if (ret)
|
|
goto err_free_adapter;
|
|
/* tell the stack to leave us alone until pch_gbe_open() is called */
|
|
netif_carrier_off(netdev);
|
|
netif_stop_queue(netdev);
|
|
|
|
dev_dbg(&pdev->dev, "PCH Network Connection\n");
|
|
|
|
/* Disable hibernation on certain platforms */
|
|
if (adapter->pdata && adapter->pdata->phy_disable_hibernate)
|
|
pch_gbe_phy_disable_hibernate(&adapter->hw);
|
|
|
|
device_set_wakeup_enable(&pdev->dev, 1);
|
|
return 0;
|
|
|
|
err_free_adapter:
|
|
pch_gbe_phy_hw_reset(&adapter->hw);
|
|
err_put_dev:
|
|
pci_dev_put(adapter->ptp_pdev);
|
|
err_free_netdev:
|
|
free_netdev(netdev);
|
|
return ret;
|
|
}
|
|
|
|
static void pch_gbe_gpio_remove_table(void *table)
|
|
{
|
|
gpiod_remove_lookup_table(table);
|
|
}
|
|
|
|
static int pch_gbe_gpio_add_table(struct device *dev, void *table)
|
|
{
|
|
gpiod_add_lookup_table(table);
|
|
return devm_add_action_or_reset(dev, pch_gbe_gpio_remove_table, table);
|
|
}
|
|
|
|
static struct gpiod_lookup_table pch_gbe_minnow_gpio_table = {
|
|
.dev_id = "0000:02:00.1",
|
|
.table = {
|
|
GPIO_LOOKUP("sch_gpio.33158", 13, NULL, GPIO_ACTIVE_LOW),
|
|
{}
|
|
},
|
|
};
|
|
|
|
/* The AR803X PHY on the MinnowBoard requires a physical pin to be toggled to
|
|
* ensure it is awake for probe and init. Request the line and reset the PHY.
|
|
*/
|
|
static int pch_gbe_minnow_platform_init(struct pci_dev *pdev)
|
|
{
|
|
struct gpio_desc *gpiod;
|
|
int ret;
|
|
|
|
ret = pch_gbe_gpio_add_table(&pdev->dev, &pch_gbe_minnow_gpio_table);
|
|
if (ret)
|
|
return ret;
|
|
|
|
gpiod = devm_gpiod_get(&pdev->dev, NULL, GPIOD_OUT_HIGH);
|
|
if (IS_ERR(gpiod))
|
|
return dev_err_probe(&pdev->dev, PTR_ERR(gpiod),
|
|
"Can't request PHY reset GPIO line\n");
|
|
|
|
gpiod_set_value(gpiod, 1);
|
|
usleep_range(1250, 1500);
|
|
gpiod_set_value(gpiod, 0);
|
|
usleep_range(1250, 1500);
|
|
|
|
return ret;
|
|
}
|
|
|
|
static struct pch_gbe_privdata pch_gbe_minnow_privdata = {
|
|
.phy_tx_clk_delay = true,
|
|
.phy_disable_hibernate = true,
|
|
.platform_init = pch_gbe_minnow_platform_init,
|
|
};
|
|
|
|
static const struct pci_device_id pch_gbe_pcidev_id[] = {
|
|
{.vendor = PCI_VENDOR_ID_INTEL,
|
|
.device = PCI_DEVICE_ID_INTEL_IOH1_GBE,
|
|
.subvendor = PCI_VENDOR_ID_CIRCUITCO,
|
|
.subdevice = PCI_SUBSYSTEM_ID_CIRCUITCO_MINNOWBOARD,
|
|
.class = (PCI_CLASS_NETWORK_ETHERNET << 8),
|
|
.class_mask = (0xFFFF00),
|
|
.driver_data = (kernel_ulong_t)&pch_gbe_minnow_privdata
|
|
},
|
|
{.vendor = PCI_VENDOR_ID_INTEL,
|
|
.device = PCI_DEVICE_ID_INTEL_IOH1_GBE,
|
|
.subvendor = PCI_ANY_ID,
|
|
.subdevice = PCI_ANY_ID,
|
|
.class = (PCI_CLASS_NETWORK_ETHERNET << 8),
|
|
.class_mask = (0xFFFF00)
|
|
},
|
|
{.vendor = PCI_VENDOR_ID_ROHM,
|
|
.device = PCI_DEVICE_ID_ROHM_ML7223_GBE,
|
|
.subvendor = PCI_ANY_ID,
|
|
.subdevice = PCI_ANY_ID,
|
|
.class = (PCI_CLASS_NETWORK_ETHERNET << 8),
|
|
.class_mask = (0xFFFF00)
|
|
},
|
|
{.vendor = PCI_VENDOR_ID_ROHM,
|
|
.device = PCI_DEVICE_ID_ROHM_ML7831_GBE,
|
|
.subvendor = PCI_ANY_ID,
|
|
.subdevice = PCI_ANY_ID,
|
|
.class = (PCI_CLASS_NETWORK_ETHERNET << 8),
|
|
.class_mask = (0xFFFF00)
|
|
},
|
|
/* required last entry */
|
|
{0}
|
|
};
|
|
|
|
#ifdef CONFIG_PM
|
|
static const struct dev_pm_ops pch_gbe_pm_ops = {
|
|
.suspend = pch_gbe_suspend,
|
|
.resume = pch_gbe_resume,
|
|
.freeze = pch_gbe_suspend,
|
|
.thaw = pch_gbe_resume,
|
|
.poweroff = pch_gbe_suspend,
|
|
.restore = pch_gbe_resume,
|
|
};
|
|
#endif
|
|
|
|
static const struct pci_error_handlers pch_gbe_err_handler = {
|
|
.error_detected = pch_gbe_io_error_detected,
|
|
.slot_reset = pch_gbe_io_slot_reset,
|
|
.resume = pch_gbe_io_resume
|
|
};
|
|
|
|
static struct pci_driver pch_gbe_driver = {
|
|
.name = KBUILD_MODNAME,
|
|
.id_table = pch_gbe_pcidev_id,
|
|
.probe = pch_gbe_probe,
|
|
.remove = pch_gbe_remove,
|
|
#ifdef CONFIG_PM
|
|
.driver.pm = &pch_gbe_pm_ops,
|
|
#endif
|
|
.shutdown = pch_gbe_shutdown,
|
|
.err_handler = &pch_gbe_err_handler
|
|
};
|
|
module_pci_driver(pch_gbe_driver);
|
|
|
|
MODULE_DESCRIPTION("EG20T PCH Gigabit ethernet Driver");
|
|
MODULE_AUTHOR("LAPIS SEMICONDUCTOR, <tshimizu818@gmail.com>");
|
|
MODULE_LICENSE("GPL");
|
|
MODULE_DEVICE_TABLE(pci, pch_gbe_pcidev_id);
|
|
|
|
/* pch_gbe_main.c */
|